diff options
Diffstat (limited to 'arch/ppc/platforms/lite5200.c')
| -rw-r--r-- | arch/ppc/platforms/lite5200.c | 73 |
1 files changed, 40 insertions, 33 deletions
diff --git a/arch/ppc/platforms/lite5200.c b/arch/ppc/platforms/lite5200.c index 7ed52dc340c9..fecbe9adc9e0 100644 --- a/arch/ppc/platforms/lite5200.c +++ b/arch/ppc/platforms/lite5200.c @@ -1,6 +1,4 @@ /* - * arch/ppc/platforms/lite5200.c - * * Platform support file for the Freescale LITE5200 based on MPC52xx. * A maximum of this file should be moved to syslib/mpc52xx_????? * so that new platform based on MPC52xx need a minimal platform file @@ -36,8 +34,7 @@ #include <asm/mpc52xx.h> #include <asm/ppc_sys.h> #include <asm/machdep.h> - -#include <syslib/mpc52xx_pci.h> +#include <asm/pci-bridge.h> extern int powersave_nap; @@ -70,44 +67,53 @@ lite5200_show_cpuinfo(struct seq_file *m) } #ifdef CONFIG_PCI +#ifdef CONFIG_LITE5200B +static int +lite5200_map_irq(struct pci_dev *dev, unsigned char idsel, + unsigned char pin) +{ + static char pci_irq_table[][4] = + /* + * PCI IDSEL/INTPIN->INTLINE + * A B C D + */ + { + {MPC52xx_IRQ0, MPC52xx_IRQ1, MPC52xx_IRQ2, MPC52xx_IRQ3}, + {MPC52xx_IRQ1, MPC52xx_IRQ2, MPC52xx_IRQ3, MPC52xx_IRQ0}, + }; + + const long min_idsel = 24, max_idsel = 25, irqs_per_slot = 4; + return PCI_IRQ_TABLE_LOOKUP; +} +#else /* Original Lite */ static int lite5200_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) { return (pin == 1) && (idsel==24) ? MPC52xx_IRQ0 : -1; } #endif +#endif static void __init lite5200_setup_cpu(void) { - struct mpc52xx_cdm __iomem *cdm; struct mpc52xx_gpio __iomem *gpio; struct mpc52xx_intr __iomem *intr; - struct mpc52xx_xlb __iomem *xlb; u32 port_config; u32 intr_ctrl; /* Map zones */ - cdm = ioremap(MPC52xx_PA(MPC52xx_CDM_OFFSET), MPC52xx_CDM_SIZE); gpio = ioremap(MPC52xx_PA(MPC52xx_GPIO_OFFSET), MPC52xx_GPIO_SIZE); - xlb = ioremap(MPC52xx_PA(MPC52xx_XLB_OFFSET), MPC52xx_XLB_SIZE); intr = ioremap(MPC52xx_PA(MPC52xx_INTR_OFFSET), MPC52xx_INTR_SIZE); - if (!cdm || !gpio || !xlb || !intr) { - printk("lite5200.c: Error while mapping CDM/GPIO/XLB/INTR during" - "lite5200_setup_cpu\n"); + if (!gpio || !intr) { + printk(KERN_ERR __FILE__ ": " + "Error while mapping GPIO/INTR during " + "lite5200_setup_cpu\n"); goto unmap_regs; } - /* Use internal 48 Mhz */ - out_8(&cdm->ext_48mhz_en, 0x00); - out_8(&cdm->fd_enable, 0x01); - if (in_be32(&cdm->rstcfg) & 0x40) /* Assumes 33Mhz clock */ - out_be16(&cdm->fd_counters, 0x0001); - else - out_be16(&cdm->fd_counters, 0x5555); - /* Get port mux config */ port_config = in_be32(&gpio->port_config); @@ -118,29 +124,29 @@ lite5200_setup_cpu(void) port_config &= ~0x00007000; /* Differential mode - USB1 only */ port_config |= 0x00001000; + /* ATA CS is on csb_4/5 */ + port_config &= ~0x03000000; + port_config |= 0x01000000; + /* Commit port config */ out_be32(&gpio->port_config, port_config); - /* Configure the XLB Arbiter */ - out_be32(&xlb->master_pri_enable, 0xff); - out_be32(&xlb->master_priority, 0x11111111); - - /* Enable ram snooping for 1GB window */ - out_be32(&xlb->config, in_be32(&xlb->config) | MPC52xx_XLB_CFG_SNOOP); - out_be32(&xlb->snoop_window, MPC52xx_PCI_TARGET_MEM | 0x1d); - - /* IRQ[0-3] setup : IRQ0 - Level Active Low */ - /* IRQ[1-3] - Level Active High */ + /* IRQ[0-3] setup */ intr_ctrl = in_be32(&intr->ctrl); intr_ctrl &= ~0x00ff0000; - intr_ctrl |= 0x00c00000; +#ifdef CONFIG_LITE5200B + /* IRQ[0-3] Level Active Low */ + intr_ctrl |= 0x00ff0000; +#else + /* IRQ0 Level Active Low + * IRQ[1-3] Level Active High */ + intr_ctrl |= 0x00c00000; +#endif out_be32(&intr->ctrl, intr_ctrl); /* Unmap reg zone */ unmap_regs: - if (cdm) iounmap(cdm); if (gpio) iounmap(gpio); - if (xlb) iounmap(xlb); if (intr) iounmap(intr); } @@ -148,7 +154,8 @@ static void __init lite5200_setup_arch(void) { /* CPU & Port mux setup */ - lite5200_setup_cpu(); + mpc52xx_setup_cpu(); /* Generic */ + lite5200_setup_cpu(); /* Platform specific */ #ifdef CONFIG_PCI /* PCI Bridge setup */ |