diff options
Diffstat (limited to 'arch/ppc/syslib/hawk_common.c')
| -rw-r--r-- | arch/ppc/syslib/hawk_common.c | 319 |
1 files changed, 319 insertions, 0 deletions
diff --git a/arch/ppc/syslib/hawk_common.c b/arch/ppc/syslib/hawk_common.c new file mode 100644 index 000000000000..a9911dc3a82f --- /dev/null +++ b/arch/ppc/syslib/hawk_common.c @@ -0,0 +1,319 @@ +/* + * arch/ppc/syslib/hawk_common.c + * + * Common Motorola PowerPlus Platform--really Falcon/Raven or HAWK. + * + * Author: Mark A. Greer + * mgreer@mvista.com + * + * 2001 (c) MontaVista, Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/pci.h> + +#include <asm/byteorder.h> +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/pci.h> +#include <asm/pci-bridge.h> +#include <asm/open_pic.h> +#include <asm/hawk.h> + +/* + * The Falcon/Raven and HAWK has 4 sets of registers: + * 1) PPC Registers which define the mappings from PPC bus to PCI bus, + * etc. + * 2) PCI Registers which define the mappings from PCI bus to PPC bus and the + * MPIC base address. + * 3) MPIC registers. + * 4) System Memory Controller (SMC) registers. + */ + +/* + * Initialize the Motorola MCG Raven or HAWK host bridge. + * + * This means setting up the PPC bus to PCI memory and I/O space mappings, + * setting the PCI memory space address of the MPIC (mapped straight + * through), and ioremap'ing the mpic registers. + * This routine will set the PCI_CONFIG_ADDR or PCI_CONFIG_DATA + * addresses based on the PCI I/O address that is passed in. + * 'OpenPIC_Addr' will be set correctly by this routine. + */ +int __init +hawk_init(struct pci_controller *hose, + uint ppc_reg_base, + ulong processor_pci_mem_start, + ulong processor_pci_mem_end, + ulong processor_pci_io_start, + ulong processor_pci_io_end, + ulong processor_mpic_base) +{ + uint addr, offset; + + /* + * Some sanity checks... + */ + if (((processor_pci_mem_start&0xffff0000) != processor_pci_mem_start) || + ((processor_pci_io_start &0xffff0000) != processor_pci_io_start)) { + printk("hawk_init: %s\n", + "PPC to PCI mappings must start on 64 KB boundaries"); + return -1; + } + + if (((processor_pci_mem_end &0x0000ffff) != 0x0000ffff) || + ((processor_pci_io_end &0x0000ffff) != 0x0000ffff)) { + printk("hawk_init: PPC to PCI mappings %s\n", + "must end just before a 64 KB boundaries"); + return -1; + } + + if (((processor_pci_mem_end - processor_pci_mem_start) != + (hose->mem_space.end - hose->mem_space.start)) || + ((processor_pci_io_end - processor_pci_io_start) != + (hose->io_space.end - hose->io_space.start))) { + printk("hawk_init: %s\n", + "PPC and PCI memory or I/O space sizes don't match"); + return -1; + } + + if ((processor_mpic_base & 0xfffc0000) != processor_mpic_base) { + printk("hawk_init: %s\n", + "MPIC address must start on 256 MB boundary"); + return -1; + } + + if ((pci_dram_offset & 0xffff0000) != pci_dram_offset) { + printk("hawk_init: %s\n", + "pci_dram_offset must be multiple of 64 KB"); + return -1; + } + + /* + * Disable previous PPC->PCI mappings. + */ + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSOFF0_OFF), 0x00000000); + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSOFF1_OFF), 0x00000000); + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSOFF2_OFF), 0x00000000); + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSOFF3_OFF), 0x00000000); + + /* + * Program the XSADD/XSOFF registers to set up the PCI Mem & I/O + * space mappings. These are the mappings going from the processor to + * the PCI bus. + * + * Note: Don't need to 'AND' start/end addresses with 0xffff0000 + * because sanity check above ensures that they are properly + * aligned. + */ + + /* Set up PPC->PCI Mem mapping */ + addr = processor_pci_mem_start | (processor_pci_mem_end >> 16); + offset = (hose->mem_space.start - processor_pci_mem_start) | 0xd2; + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSADD0_OFF), addr); + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSOFF0_OFF), offset); + + /* Set up PPC->MPIC mapping on the bridge */ + addr = processor_mpic_base | + (((processor_mpic_base + HAWK_MPIC_SIZE) >> 16) - 1); + /* No write posting for this PCI Mem space */ + offset = (hose->mem_space.start - processor_pci_mem_start) | 0xc2; + + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSADD1_OFF), addr); + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSOFF1_OFF), offset); + + /* Set up PPC->PCI I/O mapping -- Contiguous I/O space */ + addr = processor_pci_io_start | (processor_pci_io_end >> 16); + offset = (hose->io_space.start - processor_pci_io_start) | 0xc0; + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSADD3_OFF), addr); + out_be32((uint *)(ppc_reg_base + HAWK_PPC_XSOFF3_OFF), offset); + + hose->io_base_virt = (void *)ioremap(processor_pci_io_start, + (processor_pci_io_end - processor_pci_io_start + 1)); + + /* + * Set up the indirect method of accessing PCI config space. + * The PCI config addr/data pair based on start addr of PCI I/O space. + */ + setup_indirect_pci(hose, + processor_pci_io_start + HAWK_PCI_CONFIG_ADDR_OFF, + processor_pci_io_start + HAWK_PCI_CONFIG_DATA_OFF); + + /* + * Disable previous PCI->PPC mappings. + */ + + /* XXXX Put in mappings from PCI bus to processor bus XXXX */ + + /* + * Disable MPIC response to PCI I/O space (BAR 0). + * Make MPIC respond to PCI Mem space at specified address. + * (BAR 1). + */ + early_write_config_dword(hose, + 0, + PCI_DEVFN(0,0), + PCI_BASE_ADDRESS_0, + 0x00000000 | 0x1); + + early_write_config_dword(hose, + 0, + PCI_DEVFN(0,0), + PCI_BASE_ADDRESS_1, + (processor_mpic_base - + processor_pci_mem_start + + hose->mem_space.start) | 0x0); + + /* Map MPIC into vitual memory */ + OpenPIC_Addr = ioremap(processor_mpic_base, HAWK_MPIC_SIZE); + + return 0; +} + +/* + * Find the amount of RAM present. + * This assumes that PPCBug has initialized the memory controller (SMC) + * on the Falcon/HAWK correctly (i.e., it does no sanity checking). + * It also assumes that the memory base registers are set to configure the + * memory as contigous starting with "RAM A BASE", "RAM B BASE", etc. + * however, RAM base registers can be skipped (e.g. A, B, C are set, + * D is skipped but E is set is okay). + */ +#define MB (1024*1024) + +static uint reg_offset_table[] __initdata = { + HAWK_SMC_RAM_A_SIZE_REG_OFF, + HAWK_SMC_RAM_B_SIZE_REG_OFF, + HAWK_SMC_RAM_C_SIZE_REG_OFF, + HAWK_SMC_RAM_D_SIZE_REG_OFF, + HAWK_SMC_RAM_E_SIZE_REG_OFF, + HAWK_SMC_RAM_F_SIZE_REG_OFF, + HAWK_SMC_RAM_G_SIZE_REG_OFF, + HAWK_SMC_RAM_H_SIZE_REG_OFF +}; + +static uint falcon_size_table[] __initdata = { + 0 * MB, /* 0 ==> 0 MB */ + 16 * MB, /* 1 ==> 16 MB */ + 32 * MB, /* 2 ==> 32 MB */ + 64 * MB, /* 3 ==> 64 MB */ + 128 * MB, /* 4 ==> 128 MB */ + 256 * MB, /* 5 ==> 256 MB */ + 1024 * MB, /* 6 ==> 1024 MB (1 GB) */ +}; + +static uint hawk_size_table[] __initdata = { + 0 * MB, /* 0 ==> 0 MB */ + 32 * MB, /* 1 ==> 32 MB */ + 64 * MB, /* 2 ==> 64 MB */ + 64 * MB, /* 3 ==> 64 MB */ + 128 * MB, /* 4 ==> 128 MB */ + 128 * MB, /* 5 ==> 128 MB */ + 128 * MB, /* 6 ==> 128 MB */ + 256 * MB, /* 7 ==> 256 MB */ + 256 * MB, /* 8 ==> 256 MB */ + 512 * MB, /* 9 ==> 512 MB */ +}; + +/* + * *** WARNING: You MUST have a BAT set up to map in the SMC regs *** + * + * Read the memory controller's registers to determine the amount of system + * memory. Assumes that the memory controller registers are already mapped + * into virtual memory--too early to use ioremap(). + */ +unsigned long __init +hawk_get_mem_size(uint smc_base) +{ + unsigned long total; + int i, size_table_entries, reg_limit; + uint vend_dev_id; + uint *size_table; + u_char val; + + + vend_dev_id = in_be32((uint *)smc_base + PCI_VENDOR_ID); + + if (((vend_dev_id & 0xffff0000) >> 16) != PCI_VENDOR_ID_MOTOROLA) { + printk("hawk_get_mem_size: %s (0x%x)\n", + "Not a Motorola Memory Controller", vend_dev_id); + return 0; + } + + vend_dev_id &= 0x0000ffff; + + if (vend_dev_id == PCI_DEVICE_ID_MOTOROLA_FALCON) { + size_table = falcon_size_table; + size_table_entries = sizeof(falcon_size_table) / + sizeof(falcon_size_table[0]); + + reg_limit = FALCON_SMC_REG_COUNT; + } + else if (vend_dev_id == PCI_DEVICE_ID_MOTOROLA_HAWK) { + size_table = hawk_size_table; + size_table_entries = sizeof(hawk_size_table) / + sizeof(hawk_size_table[0]); + reg_limit = HAWK_SMC_REG_COUNT; + } + else { + printk("hawk_get_mem_size: %s (0x%x)\n", + "Not a Falcon or HAWK", vend_dev_id); + return 0; + } + + total = 0; + + /* Check every reg because PPCBug may skip some */ + for (i=0; i<reg_limit; i++) { + val = in_8((u_char *)(smc_base + reg_offset_table[i])); + + if (val & 0x80) { /* If enabled */ + val &= 0x0f; + + /* Don't go past end of size_table */ + if (val < size_table_entries) { + total += size_table[val]; + } + else { /* Register not set correctly */ + break; + } + } + } + + return total; +} + +int __init +hawk_mpic_init(unsigned int pci_mem_offset) +{ + unsigned short devid; + unsigned int pci_membase; + + /* Check the first PCI device to see if it is a Raven or Hawk. */ + early_read_config_word(0, 0, 0, PCI_DEVICE_ID, &devid); + + switch (devid) { + case PCI_DEVICE_ID_MOTOROLA_RAVEN: + case PCI_DEVICE_ID_MOTOROLA_HAWK: + break; + default: + OpenPIC_Addr = NULL; + return 1; + } + + /* Read the memory base register. */ + early_read_config_dword(0, 0, 0, PCI_BASE_ADDRESS_1, &pci_membase); + + if (pci_membase == 0) { + OpenPIC_Addr = NULL; + return 1; + } + + /* Map the MPIC registers to virtual memory. */ + OpenPIC_Addr = ioremap(pci_membase + pci_mem_offset, 0x22000); + + return 0; +} |