diff options
Diffstat (limited to 'arch/sh/boards')
27 files changed, 111 insertions, 1335 deletions
diff --git a/arch/sh/boards/Kconfig b/arch/sh/boards/Kconfig index 9c94711aa6ca..2018c7ea4c93 100644 --- a/arch/sh/boards/Kconfig +++ b/arch/sh/boards/Kconfig @@ -81,13 +81,6 @@ config SH_7343_SOLUTION_ENGINE Select 7343 SolutionEngine if configuring for a Hitachi SH7343 (SH-Mobile 3AS) evaluation board. -config SH_7751_SYSTEMH - bool "SystemH7751R" - depends on CPU_SUBTYPE_SH7751R - help - Select SystemH if you are configuring for a Renesas SystemH - 7751R evaluation board. - config SH_HP6XX bool "HP6XX" select SYS_SUPPORTS_APM_EMULATION diff --git a/arch/sh/boards/Makefile b/arch/sh/boards/Makefile index 38ef655cc0f0..be7d11d04b26 100644 --- a/arch/sh/boards/Makefile +++ b/arch/sh/boards/Makefile @@ -2,10 +2,12 @@ # Specific board support, not covered by a mach group. # obj-$(CONFIG_SH_MAGIC_PANEL_R2) += board-magicpanelr2.o +obj-$(CONFIG_SH_SECUREEDGE5410) += board-secureedge5410.o obj-$(CONFIG_SH_SH2007) += board-sh2007.o obj-$(CONFIG_SH_SH7785LCR) += board-sh7785lcr.o obj-$(CONFIG_SH_URQUELL) += board-urquell.o obj-$(CONFIG_SH_SHMIN) += board-shmin.o +obj-$(CONFIG_SH_EDOSK7705) += board-edosk7705.o obj-$(CONFIG_SH_EDOSK7760) += board-edosk7760.o obj-$(CONFIG_SH_ESPT) += board-espt.o obj-$(CONFIG_SH_POLARIS) += board-polaris.o diff --git a/arch/sh/boards/board-edosk7705.c b/arch/sh/boards/board-edosk7705.c new file mode 100644 index 000000000000..4cb3bb74c36f --- /dev/null +++ b/arch/sh/boards/board-edosk7705.c @@ -0,0 +1,78 @@ +/* + * arch/sh/boards/renesas/edosk7705/setup.c + * + * Copyright (C) 2000 Kazumoto Kojima + * + * Hitachi SolutionEngine Support. + * + * Modified for edosk7705 development + * board by S. Dunn, 2003. + */ +#include <linux/init.h> +#include <linux/irq.h> +#include <linux/platform_device.h> +#include <linux/interrupt.h> +#include <linux/smc91x.h> +#include <asm/machvec.h> +#include <asm/sizes.h> + +#define SMC_IOBASE 0xA2000000 +#define SMC_IO_OFFSET 0x300 +#define SMC_IOADDR (SMC_IOBASE + SMC_IO_OFFSET) + +#define ETHERNET_IRQ 0x09 + +static void __init sh_edosk7705_init_irq(void) +{ + make_imask_irq(ETHERNET_IRQ); +} + +/* eth initialization functions */ +static struct smc91x_platdata smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_IO_SHIFT_1 | IORESOURCE_IRQ_LOWLEVEL, +}; + +static struct resource smc91x_res[] = { + [0] = { + .start = SMC_IOADDR, + .end = SMC_IOADDR + SZ_32 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = ETHERNET_IRQ, + .end = ETHERNET_IRQ, + .flags = IORESOURCE_IRQ , + } +}; + +static struct platform_device smc91x_dev = { + .name = "smc91x", + .id = -1, + .num_resources = ARRAY_SIZE(smc91x_res), + .resource = smc91x_res, + + .dev = { + .platform_data = &smc91x_info, + }, +}; + +/* platform init code */ +static struct platform_device *edosk7705_devices[] __initdata = { + &smc91x_dev, +}; + +static int __init init_edosk7705_devices(void) +{ + return platform_add_devices(edosk7705_devices, + ARRAY_SIZE(edosk7705_devices)); +} +__initcall(init_edosk7705_devices); + +/* + * The Machine Vector + */ +static struct sh_machine_vector mv_edosk7705 __initmv = { + .mv_name = "EDOSK7705", + .mv_nr_irqs = 80, + .mv_init_irq = sh_edosk7705_init_irq, +}; diff --git a/arch/sh/boards/mach-snapgear/setup.c b/arch/sh/boards/board-secureedge5410.c index 331745dee379..32f875e8493d 100644 --- a/arch/sh/boards/mach-snapgear/setup.c +++ b/arch/sh/boards/board-secureedge5410.c @@ -1,6 +1,4 @@ /* - * linux/arch/sh/boards/snapgear/setup.c - * * Copyright (C) 2002 David McCullough <davidm@snapgear.com> * Copyright (C) 2003 Paul Mundt <lethal@linux-sh.org> * @@ -19,18 +17,19 @@ #include <linux/module.h> #include <linux/sched.h> #include <asm/machvec.h> -#include <mach/snapgear.h> +#include <mach/secureedge5410.h> #include <asm/irq.h> #include <asm/io.h> #include <cpu/timer.h> +unsigned short secureedge5410_ioport; + /* * EraseConfig handling functions */ - static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id) { - (void)__raw_readb(0xb8000000); /* dummy read */ + ctrl_delay(); /* dummy read */ printk("SnapGear: erase switch interrupt!\n"); @@ -39,21 +38,22 @@ static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id) static int __init eraseconfig_init(void) { + unsigned int irq = evt2irq(0x240); + printk("SnapGear: EraseConfig init\n"); + /* Setup "EraseConfig" switch on external IRQ 0 */ - if (request_irq(IRL0_IRQ, eraseconfig_interrupt, IRQF_DISABLED, + if (request_irq(irq, eraseconfig_interrupt, IRQF_DISABLED, "Erase Config", NULL)) printk("SnapGear: failed to register IRQ%d for Reset witch\n", - IRL0_IRQ); + irq); else printk("SnapGear: registered EraseConfig switch on IRQ%d\n", - IRL0_IRQ); - return(0); + irq); + return 0; } - module_init(eraseconfig_init); -/****************************************************************************/ /* * Initialize IRQ setting * @@ -62,7 +62,6 @@ module_init(eraseconfig_init); * IRL2 = eth1 * IRL3 = crypto */ - static void __init init_snapgear_IRQ(void) { printk("Setup SnapGear IRQ/IPR ...\n"); @@ -76,20 +75,5 @@ static void __init init_snapgear_IRQ(void) static struct sh_machine_vector mv_snapgear __initmv = { .mv_name = "SnapGear SecureEdge5410", .mv_nr_irqs = 72, - - .mv_inb = snapgear_inb, - .mv_inw = snapgear_inw, - .mv_inl = snapgear_inl, - .mv_outb = snapgear_outb, - .mv_outw = snapgear_outw, - .mv_outl = snapgear_outl, - - .mv_inb_p = snapgear_inb_p, - .mv_inw_p = snapgear_inw, - .mv_inl_p = snapgear_inl, - .mv_outb_p = snapgear_outb_p, - .mv_outw_p = snapgear_outw, - .mv_outl_p = snapgear_outl, - .mv_init_irq = init_snapgear_IRQ, }; diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c index 2eaeb9e59585..f48c492a68d3 100644 --- a/arch/sh/boards/mach-ecovec24/setup.c +++ b/arch/sh/boards/mach-ecovec24/setup.c @@ -720,32 +720,6 @@ static struct platform_device camera_devices[] = { }; /* FSI */ -/* - * FSI-B use external clock which came from da7210. - * So, we should change parent of fsi - */ -#define FCLKBCR 0xa415000c -static void fsimck_init(struct clk *clk) -{ - u32 status = __raw_readl(clk->enable_reg); - - /* use external clock */ - status &= ~0x000000ff; - status |= 0x00000080; - - __raw_writel(status, clk->enable_reg); -} - -static struct clk_ops fsimck_clk_ops = { - .init = fsimck_init, -}; - -static struct clk fsimckb_clk = { - .ops = &fsimck_clk_ops, - .enable_reg = (void __iomem *)FCLKBCR, - .rate = 0, /* unknown */ -}; - static struct sh_fsi_platform_info fsi_info = { .portb_flags = SH_FSI_BRS_INV | SH_FSI_OUT_SLAVE_MODE | @@ -1264,10 +1238,10 @@ static int __init arch_setup(void) /* change parent of FSI B */ clk = clk_get(NULL, "fsib_clk"); if (!IS_ERR(clk)) { - clk_register(&fsimckb_clk); - clk_set_parent(clk, &fsimckb_clk); - clk_set_rate(clk, 11000); - clk_set_rate(&fsimckb_clk, 11000); + /* 48kHz dummy clock was used to make sure 1/1 divide */ + clk_set_rate(&sh7724_fsimckb_clk, 48000); + clk_set_parent(clk, &sh7724_fsimckb_clk); + clk_set_rate(clk, 48000); clk_put(clk); } diff --git a/arch/sh/boards/mach-edosk7705/Makefile b/arch/sh/boards/mach-edosk7705/Makefile deleted file mode 100644 index cd54acb51499..000000000000 --- a/arch/sh/boards/mach-edosk7705/Makefile +++ /dev/null @@ -1,5 +0,0 @@ -# -# Makefile for the EDOSK7705 specific parts of the kernel -# - -obj-y := setup.o io.o diff --git a/arch/sh/boards/mach-edosk7705/io.c b/arch/sh/boards/mach-edosk7705/io.c deleted file mode 100644 index 5b9c57c43241..000000000000 --- a/arch/sh/boards/mach-edosk7705/io.c +++ /dev/null @@ -1,71 +0,0 @@ -/* - * arch/sh/boards/renesas/edosk7705/io.c - * - * Copyright (C) 2001 Ian da Silva, Jeremy Siegel - * Based largely on io_se.c. - * - * I/O routines for Hitachi EDOSK7705 board. - * - */ - -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/io.h> -#include <mach/edosk7705.h> -#include <asm/addrspace.h> - -#define SMC_IOADDR 0xA2000000 - -/* Map the Ethernet addresses as if it is at 0x300 - 0x320 */ -static unsigned long sh_edosk7705_isa_port2addr(unsigned long port) -{ - /* - * SMC91C96 registers are 4 byte aligned rather than the - * usual 2 byte! - */ - if (port >= 0x300 && port < 0x320) - return SMC_IOADDR + ((port - 0x300) * 2); - - maybebadio(port); - return port; -} - -/* Trying to read / write bytes on odd-byte boundaries to the Ethernet - * registers causes problems. So we bit-shift the value and read / write - * in 2 byte chunks. Setting the low byte to 0 does not cause problems - * now as odd byte writes are only made on the bit mask / interrupt - * register. This may not be the case in future Mar-2003 SJD - */ -unsigned char sh_edosk7705_inb(unsigned long port) -{ - if (port >= 0x300 && port < 0x320 && port & 0x01) - return __raw_readw(port - 1) >> 8; - - return __raw_readb(sh_edosk7705_isa_port2addr(port)); -} - -void sh_edosk7705_outb(unsigned char value, unsigned long port) -{ - if (port >= 0x300 && port < 0x320 && port & 0x01) { - __raw_writew(((unsigned short)value << 8), port - 1); - return; - } - - __raw_writeb(value, sh_edosk7705_isa_port2addr(port)); -} - -void sh_edosk7705_insb(unsigned long port, void *addr, unsigned long count) -{ - unsigned char *p = addr; - - while (count--) - *p++ = sh_edosk7705_inb(port); -} - -void sh_edosk7705_outsb(unsigned long port, const void *addr, unsigned long count) -{ - unsigned char *p = (unsigned char *)addr; - - while (count--) - sh_edosk7705_outb(*p++, port); -} diff --git a/arch/sh/boards/mach-edosk7705/setup.c b/arch/sh/boards/mach-edosk7705/setup.c deleted file mode 100644 index d59225e26fb9..000000000000 --- a/arch/sh/boards/mach-edosk7705/setup.c +++ /dev/null @@ -1,36 +0,0 @@ -/* - * arch/sh/boards/renesas/edosk7705/setup.c - * - * Copyright (C) 2000 Kazumoto Kojima - * - * Hitachi SolutionEngine Support. - * - * Modified for edosk7705 development - * board by S. Dunn, 2003. - */ -#include <linux/init.h> -#include <linux/irq.h> -#include <asm/machvec.h> -#include <mach/edosk7705.h> - -static void __init sh_edosk7705_init_irq(void) -{ - /* This is the Ethernet interrupt */ - make_imask_irq(0x09); -} - -/* - * The Machine Vector - */ -static struct sh_machine_vector mv_edosk7705 __initmv = { - .mv_name = "EDOSK7705", - .mv_nr_irqs = 80, - - .mv_inb = sh_edosk7705_inb, - .mv_outb = sh_edosk7705_outb, - - .mv_insb = sh_edosk7705_insb, - .mv_outsb = sh_edosk7705_outsb, - - .mv_init_irq = sh_edosk7705_init_irq, -}; diff --git a/arch/sh/boards/mach-microdev/io.c b/arch/sh/boards/mach-microdev/io.c index 2960c659020e..acdafb0c6404 100644 --- a/arch/sh/boards/mach-microdev/io.c +++ b/arch/sh/boards/mach-microdev/io.c @@ -54,7 +54,7 @@ /* * map I/O ports to memory-mapped addresses */ -static unsigned long microdev_isa_port2addr(unsigned long offset) +void __iomem *microdev_ioport_map(unsigned long offset, unsigned int len) { unsigned long result; @@ -72,16 +72,6 @@ static unsigned long microdev_isa_port2addr(unsigned long offset) * Configuration Registers */ result = IO_SUPERIO_PHYS + (offset << 1); -#if 0 - } else if (offset == KBD_DATA_REG || offset == KBD_CNTL_REG || - offset == KBD_STATUS_REG) { - /* - * SMSC FDC37C93xAPM SuperIO chip - * - * PS/2 Keyboard + Mouse (ports 0x60 and 0x64). - */ - result = IO_SUPERIO_PHYS + (offset << 1); -#endif } else if (((offset >= IO_IDE1_BASE) && (offset < IO_IDE1_BASE + IO_IDE_EXTENT)) || (offset == IO_IDE1_MISC)) { @@ -131,237 +121,5 @@ static unsigned long microdev_isa_port2addr(unsigned long offset) result = PVR; } - return result; -} - -#define PORT2ADDR(x) (microdev_isa_port2addr(x)) - -static inline void delay(void) -{ -#if defined(CONFIG_PCI) - /* System board present, just make a dummy SRAM access. (CS0 will be - mapped to PCI memory, probably good to avoid it.) */ - __raw_readw(0xa6800000); -#else - /* CS0 will be mapped to flash, ROM etc so safe to access it. */ - __raw_readw(0xa0000000); -#endif -} - -unsigned char microdev_inb(unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) - return microdev_pci_inb(port); -#endif - return *(volatile unsigned char*)PORT2ADDR(port); -} - -unsigned short microdev_inw(unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) - return microdev_pci_inw(port); -#endif - return *(volatile unsigned short*)PORT2ADDR(port); -} - -unsigned int microdev_inl(unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) - return microdev_pci_inl(port); -#endif - return *(volatile unsigned int*)PORT2ADDR(port); -} - -void microdev_outw(unsigned short b, unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) { - microdev_pci_outw(b, port); - return; - } -#endif - *(volatile unsigned short*)PORT2ADDR(port) = b; -} - -void microdev_outb(unsigned char b, unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) { - microdev_pci_outb(b, port); - return; - } -#endif - - /* - * There is a board feature with the current SH4-202 MicroDev in - * that the 2 byte enables (nBE0 and nBE1) are tied together (and - * to the Chip Select Line (Ethernet_CS)). Due to this connectivity, - * it is not possible to safely perform 8-bit writes to the - * Ethernet registers, as 16-bits will be consumed from the Data - * lines (corrupting the other byte). Hence, this function is - * written to implement 16-bit read/modify/write for all byte-wide - * accesses. - * - * Note: there is no problem with byte READS (even or odd). - * - * Sean McGoogan - 16th June 2003. - */ - if ((port >= IO_LAN91C111_BASE) && - (port < IO_LAN91C111_BASE + IO_LAN91C111_EXTENT)) { - /* - * Then are trying to perform a byte-write to the - * LAN91C111. This needs special care. - */ - if (port % 2 == 1) { /* is the port odd ? */ - /* unset bit-0, i.e. make even */ - const unsigned long evenPort = port-1; - unsigned short word; - - /* - * do a 16-bit read/write to write to 'port', - * preserving even byte. - * - * Even addresses are bits 0-7 - * Odd addresses are bits 8-15 - */ - word = microdev_inw(evenPort); - word = (word & 0xffu) | (b << 8); - microdev_outw(word, evenPort); - } else { - /* else, we are trying to do an even byte write */ - unsigned short word; - - /* - * do a 16-bit read/write to write to 'port', - * preserving odd byte. - * - * Even addresses are bits 0-7 - * Odd addresses are bits 8-15 - */ - word = microdev_inw(port); - word = (word & 0xff00u) | (b); - microdev_outw(word, port); - } - } else { - *(volatile unsigned char*)PORT2ADDR(port) = b; - } -} - -void microdev_outl(unsigned int b, unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) { - microdev_pci_outl(b, port); - return; - } -#endif - *(volatile unsigned int*)PORT2ADDR(port) = b; -} - -unsigned char microdev_inb_p(unsigned long port) -{ - unsigned char v = microdev_inb(port); - delay(); - return v; -} - -unsigned short microdev_inw_p(unsigned long port) -{ - unsigned short v = microdev_inw(port); - delay(); - return v; -} - -unsigned int microdev_inl_p(unsigned long port) -{ - unsigned int v = microdev_inl(port); - delay(); - return v; -} - -void microdev_outb_p(unsigned char b, unsigned long port) -{ - microdev_outb(b, port); - delay(); -} - -void microdev_outw_p(unsigned short b, unsigned long port) -{ - microdev_outw(b, port); - delay(); -} - -void microdev_outl_p(unsigned int b, unsigned long port) -{ - microdev_outl(b, port); - delay(); -} - -void microdev_insb(unsigned long port, void *buffer, unsigned long count) -{ - volatile unsigned char *port_addr; - unsigned char *buf = buffer; - - port_addr = (volatile unsigned char *)PORT2ADDR(port); - - while (count--) - *buf++ = *port_addr; -} - -void microdev_insw(unsigned long port, void *buffer, unsigned long count) -{ - volatile unsigned short *port_addr; - unsigned short *buf = buffer; - - port_addr = (volatile unsigned short *)PORT2ADDR(port); - - while (count--) - *buf++ = *port_addr; -} - -void microdev_insl(unsigned long port, void *buffer, unsigned long count) -{ - volatile unsigned long *port_addr; - unsigned int *buf = buffer; - - port_addr = (volatile unsigned long *)PORT2ADDR(port); - - while (count--) - *buf++ = *port_addr; -} - -void microdev_outsb(unsigned long port, const void *buffer, unsigned long count) -{ - volatile unsigned char *port_addr; - const unsigned char *buf = buffer; - - port_addr = (volatile unsigned char *)PORT2ADDR(port); - - while (count--) - *port_addr = *buf++; -} - -void microdev_outsw(unsigned long port, const void *buffer, unsigned long count) -{ - volatile unsigned short *port_addr; - const unsigned short *buf = buffer; - - port_addr = (volatile unsigned short *)PORT2ADDR(port); - - while (count--) - *port_addr = *buf++; -} - -void microdev_outsl(unsigned long port, const void *buffer, unsigned long count) -{ - volatile unsigned long *port_addr; - const unsigned int *buf = buffer; - - port_addr = (volatile unsigned long *)PORT2ADDR(port); - - while (count--) - *port_addr = *buf++; + return (void __iomem *)result; } diff --git a/arch/sh/boards/mach-microdev/setup.c b/arch/sh/boards/mach-microdev/setup.c index d1df2a4fb9b8..d8a747291e03 100644 --- a/arch/sh/boards/mach-microdev/setup.c +++ b/arch/sh/boards/mach-microdev/setup.c @@ -195,27 +195,6 @@ device_initcall(microdev_devices_setup); static struct sh_machine_vector mv_sh4202_microdev __initmv = { .mv_name = "SH4-202 MicroDev", .mv_nr_irqs = 72, - - .mv_inb = microdev_inb, - .mv_inw = microdev_inw, - .mv_inl = microdev_inl, - .mv_outb = microdev_outb, - .mv_outw = microdev_outw, - .mv_outl = microdev_outl, - - .mv_inb_p = microdev_inb_p, - .mv_inw_p = microdev_inw_p, - .mv_inl_p = microdev_inl_p, - .mv_outb_p = microdev_outb_p, - .mv_outw_p = microdev_outw_p, - .mv_outl_p = microdev_outl_p, - - .mv_insb = microdev_insb, - .mv_insw = microdev_insw, - .mv_insl = microdev_insl, - .mv_outsb = microdev_outsb, - .mv_outsw = microdev_outsw, - .mv_outsl = microdev_outsl, - + .mv_ioport_map = microdev_ioport_map, .mv_init_irq = init_microdev_irq, }; diff --git a/arch/sh/boards/mach-se/7206/Makefile b/arch/sh/boards/mach-se/7206/Makefile index 63e7ed699f39..5c9eaa0535b9 100644 --- a/arch/sh/boards/mach-se/7206/Makefile +++ b/arch/sh/boards/mach-se/7206/Makefile @@ -2,4 +2,4 @@ # Makefile for the 7206 SolutionEngine specific parts of the kernel # -obj-y := setup.o io.o irq.o +obj-y := setup.o irq.o diff --git a/arch/sh/boards/mach-se/7206/io.c b/arch/sh/boards/mach-se/7206/io.c deleted file mode 100644 index adadc77532ee..000000000000 --- a/arch/sh/boards/mach-se/7206/io.c +++ /dev/null @@ -1,104 +0,0 @@ -/* $Id: io.c,v 1.5 2004/02/22 23:08:43 kkojima Exp $ - * - * linux/arch/sh/boards/se/7206/io.c - * - * Copyright (C) 2006 Yoshinori Sato - * - * I/O routine for Hitachi 7206 SolutionEngine. - * - */ - -#include <linux/kernel.h> -#include <linux/types.h> -#include <asm/io.h> -#include <mach-se/mach/se7206.h> - - -static inline void delay(void) -{ - __raw_readw(0x20000000); /* P2 ROM Area */ -} - -/* MS7750 requires special versions of in*, out* routines, since - PC-like io ports are located at upper half byte of 16-bit word which - can be accessed only with 16-bit wide. */ - -static inline volatile __u16 * -port2adr(unsigned int port) -{ - if (port >= 0x2000 && port < 0x2020) - return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000)); - else if (port >= 0x300 && port < 0x310) - return (volatile __u16 *) (PA_SMSC + (port - 0x300)); - - return (volatile __u16 *)port; -} - -unsigned char se7206_inb(unsigned long port) -{ - return (*port2adr(port)) & 0xff; -} - -unsigned char se7206_inb_p(unsigned long port) -{ - unsigned long v; - - v = (*port2adr(port)) & 0xff; - delay(); - return v; -} - -unsigned short se7206_inw(unsigned long port) -{ - return *port2adr(port); -} - -void se7206_outb(unsigned char value, unsigned long port) -{ - *(port2adr(port)) = value; -} - -void se7206_outb_p(unsigned char value, unsigned long port) -{ - *(port2adr(port)) = value; - delay(); -} - -void se7206_outw(unsigned short value, unsigned long port) -{ - *port2adr(port) = value; -} - -void se7206_insb(unsigned long port, void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - __u8 *ap = addr; - - while (count--) - *ap++ = *p; -} - -void se7206_insw(unsigned long port, void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - __u16 *ap = addr; - while (count--) - *ap++ = *p; -} - -void se7206_outsb(unsigned long port, const void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - const __u8 *ap = addr; - - while (count--) - *p = *ap++; -} - -void se7206_outsw(unsigned long port, const void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - const __u16 *ap = addr; - while (count--) - *p = *ap++; -} diff --git a/arch/sh/boards/mach-se/7206/irq.c b/arch/sh/boards/mach-se/7206/irq.c index 883b21eacaa6..d961949600fd 100644 --- a/arch/sh/boards/mach-se/7206/irq.c +++ b/arch/sh/boards/mach-se/7206/irq.c @@ -139,11 +139,13 @@ void __init init_se7206_IRQ(void) make_se7206_irq(IRQ0_IRQ); /* SMC91C111 */ make_se7206_irq(IRQ1_IRQ); /* ATA */ make_se7206_irq(IRQ3_IRQ); /* SLOT / PCM */ - __raw_writew(inw(INTC_ICR1) | 0x000b ,INTC_ICR1 ) ; /* ICR1 */ + + __raw_writew(__raw_readw(INTC_ICR1) | 0x000b, INTC_ICR); /* ICR1 */ /* FPGA System register setup*/ __raw_writew(0x0000,INTSTS0); /* Clear INTSTS0 */ __raw_writew(0x0000,INTSTS1); /* Clear INTSTS1 */ + /* IRQ0=LAN, IRQ1=ATA, IRQ3=SLT,PCM */ __raw_writew(0x0001,INTSEL); } diff --git a/arch/sh/boards/mach-se/7206/setup.c b/arch/sh/boards/mach-se/7206/setup.c index 8f5c65d43d1d..7f4871c71a01 100644 --- a/arch/sh/boards/mach-se/7206/setup.c +++ b/arch/sh/boards/mach-se/7206/setup.c @@ -86,20 +86,5 @@ __initcall(se7206_devices_setup); static struct sh_machine_vector mv_se __initmv = { .mv_name = "SolutionEngine", .mv_nr_irqs = 256, - .mv_inb = se7206_inb, - .mv_inw = se7206_inw, - .mv_outb = se7206_outb, - .mv_outw = se7206_outw, - - .mv_inb_p = se7206_inb_p, - .mv_inw_p = se7206_inw, - .mv_outb_p = se7206_outb_p, - .mv_outw_p = se7206_outw, - - .mv_insb = se7206_insb, - .mv_insw = se7206_insw, - .mv_outsb = se7206_outsb, - .mv_outsw = se7206_outsw, - .mv_init_irq = init_se7206_IRQ, }; diff --git a/arch/sh/boards/mach-se/770x/Makefile b/arch/sh/boards/mach-se/770x/Makefile index 8e624b06d5ea..43ea14feef51 100644 --- a/arch/sh/boards/mach-se/770x/Makefile +++ b/arch/sh/boards/mach-se/770x/Makefile @@ -2,4 +2,4 @@ # Makefile for the 770x SolutionEngine specific parts of the kernel # -obj-y := setup.o io.o irq.o +obj-y := setup.o irq.o diff --git a/arch/sh/boards/mach-se/770x/io.c b/arch/sh/boards/mach-se/770x/io.c deleted file mode 100644 index 28833c8786ea..000000000000 --- a/arch/sh/boards/mach-se/770x/io.c +++ /dev/null @@ -1,156 +0,0 @@ -/* - * Copyright (C) 2000 Kazumoto Kojima - * - * I/O routine for Hitachi SolutionEngine. - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <asm/io.h> -#include <mach-se/mach/se.h> - -/* MS7750 requires special versions of in*, out* routines, since - PC-like io ports are located at upper half byte of 16-bit word which - can be accessed only with 16-bit wide. */ - -static inline volatile __u16 * -port2adr(unsigned int port) -{ - if (port & 0xff000000) - return ( volatile __u16 *) port; - if (port >= 0x2000) - return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000)); - else if (port >= 0x1000) - return (volatile __u16 *) (PA_83902 + (port << 1)); - else - return (volatile __u16 *) (PA_SUPERIO + (port << 1)); -} - -static inline int -shifted_port(unsigned long port) -{ - /* For IDE registers, value is not shifted */ - if ((0x1f0 <= port && port < 0x1f8) || port == 0x3f6) - return 0; - else - return 1; -} - -unsigned char se_inb(unsigned long port) -{ - if (shifted_port(port)) - return (*port2adr(port) >> 8); - else - return (*port2adr(port))&0xff; -} - -unsigned char se_inb_p(unsigned long port) -{ - unsigned long v; - - if (shifted_port(port)) - v = (*port2adr(port) >> 8); - else - v = (*port2adr(port))&0xff; - ctrl_delay(); - return v; -} - -unsigned short se_inw(unsigned long port) -{ - if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -unsigned int se_inl(unsigned long port) -{ - maybebadio(port); - return 0; -} - -void se_outb(unsigned char value, unsigned long port) -{ - if (shifted_port(port)) - *(port2adr(port)) = value << 8; - else - *(port2adr(port)) = value; -} - -void se_outb_p(unsigned char value, unsigned long port) -{ - if (shifted_port(port)) - *(port2adr(port)) = value << 8; - else - *(port2adr(port)) = value; - ctrl_delay(); -} - -void se_outw(unsigned short value, unsigned long port) -{ - if (port >= 0x2000) - *port2adr(port) = value; - else - maybebadio(port); -} - -void se_outl(unsigned int value, unsigned long port) -{ - maybebadio(port); -} - -void se_insb(unsigned long port, void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - __u8 *ap = addr; - - if (shifted_port(port)) { - while (count--) - *ap++ = *p >> 8; - } else { - while (count--) - *ap++ = *p; - } -} - -void se_insw(unsigned long port, void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - __u16 *ap = addr; - while (count--) - *ap++ = *p; -} - -void se_insl(unsigned long port, void *addr, unsigned long count) -{ - maybebadio(port); -} - -void se_outsb(unsigned long port, const void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - const __u8 *ap = addr; - - if (shifted_port(port)) { - while (count--) - *p = *ap++ << 8; - } else { - while (count--) - *p = *ap++; - } -} - -void se_outsw(unsigned long port, const void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - const __u16 *ap = addr; - - while (count--) - *p = *ap++; -} - -void se_outsl(unsigned long port, const void *addr, unsigned long count) -{ - maybebadio(port); -} diff --git a/arch/sh/boards/mach-se/770x/setup.c b/arch/sh/boards/mach-se/770x/setup.c index 66d39d1b0901..31330c65c0ce 100644 --- a/arch/sh/boards/mach-se/770x/setup.c +++ b/arch/sh/boards/mach-se/770x/setup.c @@ -195,27 +195,5 @@ static struct sh_machine_vector mv_se __initmv = { #elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712) .mv_nr_irqs = 104, #endif - - .mv_inb = se_inb, - .mv_inw = se_inw, - .mv_inl = se_inl, - .mv_outb = se_outb, - .mv_outw = se_outw, - .mv_outl = se_outl, - - .mv_inb_p = se_inb_p, - .mv_inw_p = se_inw, - .mv_inl_p = se_inl, - .mv_outb_p = se_outb_p, - .mv_outw_p = se_outw, - .mv_outl_p = se_outl, - - .mv_insb = se_insb, - .mv_insw = se_insw, - .mv_insl = se_insl, - .mv_outsb = se_outsb, - .mv_outsw = se_outsw, - .mv_outsl = se_outsl, - .mv_init_irq = init_se_IRQ, }; diff --git a/arch/sh/boards/mach-se/7724/setup.c b/arch/sh/boards/mach-se/7724/setup.c index c31d228fdfc6..527a0cd956b5 100644 --- a/arch/sh/boards/mach-se/7724/setup.c +++ b/arch/sh/boards/mach-se/7724/setup.c @@ -283,31 +283,6 @@ static struct platform_device ceu1_device = { }; /* FSI */ -/* - * FSI-A use external clock which came from ak464x. - * So, we should change parent of fsi - */ -#define FCLKACR 0xa4150008 -static void fsimck_init(struct clk *clk) -{ - u32 status = __raw_readl(clk->enable_reg); - - /* use external clock */ - status &= ~0x000000ff; - status |= 0x00000080; - __raw_writel(status, clk->enable_reg); -} - -static struct clk_ops fsimck_clk_ops = { - .init = fsimck_init, -}; - -static struct clk fsimcka_clk = { - .ops = &fsimck_clk_ops, - .enable_reg = (void __iomem *)FCLKACR, - .rate = 0, /* unknown */ -}; - /* change J20, J21, J22 pin to 1-2 connection to use slave mode */ static struct sh_fsi_platform_info fsi_info = { .porta_flags = SH_FSI_BRS_INV | @@ -852,37 +827,29 @@ static int __init devices_setup(void) gpio_request(GPIO_FN_KEYOUT0, NULL); /* enable FSI */ - gpio_request(GPIO_FN_FSIMCKB, NULL); gpio_request(GPIO_FN_FSIMCKA, NULL); + gpio_request(GPIO_FN_FSIIASD, NULL); gpio_request(GPIO_FN_FSIOASD, NULL); gpio_request(GPIO_FN_FSIIABCK, NULL); gpio_request(GPIO_FN_FSIIALRCK, NULL); gpio_request(GPIO_FN_FSIOABCK, NULL); gpio_request(GPIO_FN_FSIOALRCK, NULL); gpio_request(GPIO_FN_CLKAUDIOAO, NULL); - gpio_request(GPIO_FN_FSIIBSD, NULL); - gpio_request(GPIO_FN_FSIOBSD, NULL); - gpio_request(GPIO_FN_FSIIBBCK, NULL); - gpio_request(GPIO_FN_FSIIBLRCK, NULL); - gpio_request(GPIO_FN_FSIOBBCK, NULL); - gpio_request(GPIO_FN_FSIOBLRCK, NULL); - gpio_request(GPIO_FN_CLKAUDIOBO, NULL); - gpio_request(GPIO_FN_FSIIASD, NULL); /* set SPU2 clock to 83.4 MHz */ clk = clk_get(NULL, "spu_clk"); - if (clk) { + if (!IS_ERR(clk)) { clk_set_rate(clk, clk_round_rate(clk, 83333333)); clk_put(clk); } /* change parent of FSI A */ clk = clk_get(NULL, "fsia_clk"); - if (clk) { - clk_register(&fsimcka_clk); - clk_set_parent(clk, &fsimcka_clk); - clk_set_rate(clk, 11000); - clk_set_rate(&fsimcka_clk, 11000); + if (!IS_ERR(clk)) { + /* 48kHz dummy clock was used to make sure 1/1 divide */ + clk_set_rate(&sh7724_fsimcka_clk, 48000); + clk_set_parent(clk, &sh7724_fsimcka_clk); + clk_set_rate(clk, 48000); clk_put(clk); } diff --git a/arch/sh/boards/mach-se/7751/Makefile b/arch/sh/boards/mach-se/7751/Makefile index e6f4341bfe6e..a338fd9d5039 100644 --- a/arch/sh/boards/mach-se/7751/Makefile +++ b/arch/sh/boards/mach-se/7751/Makefile @@ -2,4 +2,4 @@ # Makefile for the 7751 SolutionEngine specific parts of the kernel # -obj-y := setup.o io.o irq.o +obj-y := setup.o irq.o diff --git a/arch/sh/boards/mach-se/7751/io.c b/arch/sh/boards/mach-se/7751/io.c deleted file mode 100644 index 6e75bd4459e5..000000000000 --- a/arch/sh/boards/mach-se/7751/io.c +++ /dev/null @@ -1,119 +0,0 @@ -/* - * Copyright (C) 2001 Ian da Silva, Jeremy Siegel - * Based largely on io_se.c. - * - * I/O routine for Hitachi 7751 SolutionEngine. - * - * Initial version only to support LAN access; some - * placeholder code from io_se.c left in with the - * expectation of later SuperIO and PCMCIA access. - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/pci.h> -#include <asm/io.h> -#include <mach-se/mach/se7751.h> -#include <asm/addrspace.h> - -static inline volatile u16 *port2adr(unsigned int port) -{ - if (port >= 0x2000) - return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000)); - maybebadio((unsigned long)port); - return (volatile __u16*)port; -} - -/* - * General outline: remap really low stuff [eventually] to SuperIO, - * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO) - * is mapped through the PCI IO window. Stuff with high bits (PXSEG) - * should be way beyond the window, and is used w/o translation for - * compatibility. - */ -unsigned char sh7751se_inb(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned char *)port; - else - return (*port2adr(port)) & 0xff; -} - -unsigned char sh7751se_inb_p(unsigned long port) -{ - unsigned char v; - - if (PXSEG(port)) - v = *(volatile unsigned char *)port; - else - v = (*port2adr(port)) & 0xff; - ctrl_delay(); - return v; -} - -unsigned short sh7751se_inw(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned short *)port; - else if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -unsigned int sh7751se_inl(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned long *)port; - else if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -void sh7751se_outb(unsigned char value, unsigned long port) -{ - - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else - *(port2adr(port)) = value; -} - -void sh7751se_outb_p(unsigned char value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else - *(port2adr(port)) = value; - ctrl_delay(); -} - -void sh7751se_outw(unsigned short value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned short *)port = value; - else if (port >= 0x2000) - *port2adr(port) = value; - else - maybebadio(port); -} - -void sh7751se_outl(unsigned int value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned long *)port = value; - else - maybebadio(port); -} - -void sh7751se_insl(unsigned long port, void *addr, unsigned long count) -{ - maybebadio(port); -} - -void sh7751se_outsl(unsigned long port, const void *addr, unsigned long count) -{ - maybebadio(port); -} diff --git a/arch/sh/boards/mach-se/7751/setup.c b/arch/sh/boards/mach-se/7751/setup.c index 50572512e3e8..9fbc51beb181 100644 --- a/arch/sh/boards/mach-se/7751/setup.c +++ b/arch/sh/boards/mach-se/7751/setup.c @@ -56,23 +56,5 @@ __initcall(se7751_devices_setup); static struct sh_machine_vector mv_7751se __initmv = { .mv_name = "7751 SolutionEngine", .mv_nr_irqs = 72, - - .mv_inb = sh7751se_inb, - .mv_inw = sh7751se_inw, - .mv_inl = sh7751se_inl, - .mv_outb = sh7751se_outb, - .mv_outw = sh7751se_outw, - .mv_outl = sh7751se_outl, - - .mv_inb_p = sh7751se_inb_p, - .mv_inw_p = sh7751se_inw, - .mv_inl_p = sh7751se_inl, - .mv_outb_p = sh7751se_outb_p, - .mv_outw_p = sh7751se_outw, - .mv_outl_p = sh7751se_outl, - - .mv_insl = sh7751se_insl, - .mv_outsl = sh7751se_outsl, - .mv_init_irq = init_7751se_IRQ, }; diff --git a/arch/sh/boards/mach-snapgear/Makefile b/arch/sh/boards/mach-snapgear/Makefile deleted file mode 100644 index d2d2f4b6a502..000000000000 --- a/arch/sh/boards/mach-snapgear/Makefile +++ /dev/null @@ -1,5 +0,0 @@ -# -# Makefile for the SnapGear specific parts of the kernel -# - -obj-y := setup.o io.o diff --git a/arch/sh/boards/mach-snapgear/io.c b/arch/sh/boards/mach-snapgear/io.c deleted file mode 100644 index 476650e42dbc..000000000000 --- a/arch/sh/boards/mach-snapgear/io.c +++ /dev/null @@ -1,121 +0,0 @@ -/* - * Copyright (C) 2002 David McCullough <davidm@snapgear.com> - * Copyright (C) 2001 Ian da Silva, Jeremy Siegel - * Based largely on io_se.c. - * - * I/O routine for Hitachi 7751 SolutionEngine. - * - * Initial version only to support LAN access; some - * placeholder code from io_se.c left in with the - * expectation of later SuperIO and PCMCIA access. - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/pci.h> -#include <asm/io.h> -#include <asm/addrspace.h> - -#ifdef CONFIG_SH_SECUREEDGE5410 -unsigned short secureedge5410_ioport; -#endif - -static inline volatile __u16 *port2adr(unsigned int port) -{ - maybebadio((unsigned long)port); - return (volatile __u16*)port; -} - -/* - * General outline: remap really low stuff [eventually] to SuperIO, - * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO) - * is mapped through the PCI IO window. Stuff with high bits (PXSEG) - * should be way beyond the window, and is used w/o translation for - * compatibility. - */ -unsigned char snapgear_inb(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned char *)port; - else - return (*port2adr(port)) & 0xff; -} - -unsigned char snapgear_inb_p(unsigned long port) -{ - unsigned char v; - - if (PXSEG(port)) - v = *(volatile unsigned char *)port; - else - v = (*port2adr(port))&0xff; - ctrl_delay(); - return v; -} - -unsigned short snapgear_inw(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned short *)port; - else if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -unsigned int snapgear_inl(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned long *)port; - else if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -void snapgear_outb(unsigned char value, unsigned long port) -{ - - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else - *(port2adr(port)) = value; -} - -void snapgear_outb_p(unsigned char value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else - *(port2adr(port)) = value; - ctrl_delay(); -} - -void snapgear_outw(unsigned short value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned short *)port = value; - else if (port >= 0x2000) - *port2adr(port) = value; - else - maybebadio(port); -} - -void snapgear_outl(unsigned int value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned long *)port = value; - else - maybebadio(port); -} - -void snapgear_insl(unsigned long port, void *addr, unsigned long count) -{ - maybebadio(port); -} - -void snapgear_outsl(unsigned long port, const void *addr, unsigned long count) -{ - maybebadio(port); -} diff --git a/arch/sh/boards/mach-systemh/Makefile b/arch/sh/boards/mach-systemh/Makefile deleted file mode 100644 index 2cc6a23d9d39..000000000000 --- a/arch/sh/boards/mach-systemh/Makefile +++ /dev/null @@ -1,13 +0,0 @@ -# -# Makefile for the SystemH specific parts of the kernel -# - -obj-y := setup.o irq.o io.o - -# XXX: This wants to be consolidated in arch/sh/drivers/pci, and more -# importantly, with the generic sh7751_pcic_init() code. For now, we'll -# just abuse the hell out of kbuild, because we can.. - -obj-$(CONFIG_PCI) += pci.o -pci-y := ../../se/7751/pci.o - diff --git a/arch/sh/boards/mach-systemh/io.c b/arch/sh/boards/mach-systemh/io.c deleted file mode 100644 index 15577ff1f715..000000000000 --- a/arch/sh/boards/mach-systemh/io.c +++ /dev/null @@ -1,158 +0,0 @@ -/* - * linux/arch/sh/boards/renesas/systemh/io.c - * - * Copyright (C) 2001 Ian da Silva, Jeremy Siegel - * Based largely on io_se.c. - * - * I/O routine for Hitachi 7751 Systemh. - */ -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/pci.h> -#include <mach/systemh7751.h> -#include <asm/addrspace.h> -#include <asm/io.h> - -#define ETHER_IOMAP(adr) (0xB3000000 + (adr)) /*map to 16bits access area - of smc lan chip*/ -static inline volatile __u16 * -port2adr(unsigned int port) -{ - if (port >= 0x2000) - return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000)); - maybebadio((unsigned long)port); - return (volatile __u16*)port; -} - -/* - * General outline: remap really low stuff [eventually] to SuperIO, - * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO) - * is mapped through the PCI IO window. Stuff with high bits (PXSEG) - * should be way beyond the window, and is used w/o translation for - * compatibility. - */ -unsigned char sh7751systemh_inb(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned char *)port; - else if (port <= 0x3F1) - return *(volatile unsigned char *)ETHER_IOMAP(port); - else - return (*port2adr(port))&0xff; -} - -unsigned char sh7751systemh_inb_p(unsigned long port) -{ - unsigned char v; - - if (PXSEG(port)) - v = *(volatile unsigned char *)port; - else if (port <= 0x3F1) - v = *(volatile unsigned char *)ETHER_IOMAP(port); - else - v = (*port2adr(port))&0xff; - ctrl_delay(); - return v; -} - -unsigned short sh7751systemh_inw(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned short *)port; - else if (port >= 0x2000) - return *port2adr(port); - else if (port <= 0x3F1) - return *(volatile unsigned int *)ETHER_IOMAP(port); - else - maybebadio(port); - return 0; -} - -unsigned int sh7751systemh_inl(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned long *)port; - else if (port >= 0x2000) - return *port2adr(port); - else if (port <= 0x3F1) - return *(volatile unsigned int *)ETHER_IOMAP(port); - else - maybebadio(port); - return 0; -} - -void sh7751systemh_outb(unsigned char value, unsigned long port) -{ - - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else if (port <= 0x3F1) - *(volatile unsigned char *)ETHER_IOMAP(port) = value; - else - *(port2adr(port)) = value; -} - -void sh7751systemh_outb_p(unsigned char value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else if (port <= 0x3F1) - *(volatile unsigned char *)ETHER_IOMAP(port) = value; - else - *(port2adr(port)) = value; - ctrl_delay(); -} - -void sh7751systemh_outw(unsigned short value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned short *)port = value; - else if (port >= 0x2000) - *port2adr(port) = value; - else if (port <= 0x3F1) - *(volatile unsigned short *)ETHER_IOMAP(port) = value; - else - maybebadio(port); -} - -void sh7751systemh_outl(unsigned int value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned long *)port = value; - else - maybebadio(port); -} - -void sh7751systemh_insb(unsigned long port, void *addr, unsigned long count) -{ - unsigned char *p = addr; - while (count--) *p++ = sh7751systemh_inb(port); -} - -void sh7751systemh_insw(unsigned long port, void *addr, unsigned long count) -{ - unsigned short *p = addr; - while (count--) *p++ = sh7751systemh_inw(port); -} - -void sh7751systemh_insl(unsigned long port, void *addr, unsigned long count) -{ - maybebadio(port); -} - -void sh7751systemh_outsb(unsigned long port, const void *addr, unsigned long count) -{ - unsigned char *p = (unsigned char*)addr; - while (count--) sh7751systemh_outb(*p++, port); -} - -void sh7751systemh_outsw(unsigned long port, const void *addr, unsigned long count) -{ - unsigned short *p = (unsigned short*)addr; - while (count--) sh7751systemh_outw(*p++, port); -} - -void sh7751systemh_outsl(unsigned long port, const void *addr, unsigned long count) -{ - maybebadio(port); -} diff --git a/arch/sh/boards/mach-systemh/irq.c b/arch/sh/boards/mach-systemh/irq.c deleted file mode 100644 index e5ee13adeff4..000000000000 --- a/arch/sh/boards/mach-systemh/irq.c +++ /dev/null @@ -1,61 +0,0 @@ -/* - * linux/arch/sh/boards/renesas/systemh/irq.c - * - * Copyright (C) 2000 Kazumoto Kojima - * - * Hitachi SystemH Support. - * - * Modified for 7751 SystemH by - * Jonathan Short. - */ - -#include <linux/init.h> -#include <linux/irq.h> -#include <linux/interrupt.h> -#include <linux/io.h> - -#include <mach/systemh7751.h> -#include <asm/smc37c93x.h> - -/* address of external interrupt mask register - * address must be set prior to use these (maybe in init_XXX_irq()) - * XXX : is it better to use .config than specifying it in code? */ -static unsigned long *systemh_irq_mask_register = (unsigned long *)0xB3F10004; -static unsigned long *systemh_irq_request_register = (unsigned long *)0xB3F10000; - -static void disable_systemh_irq(struct irq_data *data) -{ - unsigned long val, mask = 0x01 << 1; - - /* Clear the "irq"th bit in the mask and set it in the request */ - val = __raw_readl((unsigned long)systemh_irq_mask_register); - val &= ~mask; - __raw_writel(val, (unsigned long)systemh_irq_mask_register); - - val = __raw_readl((unsigned long)systemh_irq_request_register); - val |= mask; - __raw_writel(val, (unsigned long)systemh_irq_request_register); -} - -static void enable_systemh_irq(struct irq_data *data) -{ - unsigned long val, mask = 0x01 << 1; - - /* Set "irq"th bit in the mask register */ - val = __raw_readl((unsigned long)systemh_irq_mask_register); - val |= mask; - __raw_writel(val, (unsigned long)systemh_irq_mask_register); -} - -static struct irq_chip systemh_irq_type = { - .name = "SystemH Register", - .irq_unmask = enable_systemh_irq, - .irq_mask = disable_systemh_irq, -}; - -void make_systemh_irq(unsigned int irq) -{ - disable_irq_nosync(irq); - set_irq_chip_and_handler(irq, &systemh_irq_type, handle_level_irq); - disable_systemh_irq(irq_get_irq_data(irq)); -} diff --git a/arch/sh/boards/mach-systemh/setup.c b/arch/sh/boards/mach-systemh/setup.c deleted file mode 100644 index 219fd800a43f..000000000000 --- a/arch/sh/boards/mach-systemh/setup.c +++ /dev/null @@ -1,57 +0,0 @@ -/* - * linux/arch/sh/boards/renesas/systemh/setup.c - * - * Copyright (C) 2000 Kazumoto Kojima - * Copyright (C) 2003 Paul Mundt - * - * Hitachi SystemH Support. - * - * Modified for 7751 SystemH by Jonathan Short. - * - * Rewritten for 2.6 by Paul Mundt. - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ -#include <linux/init.h> -#include <asm/machvec.h> -#include <mach/systemh7751.h> - -extern void make_systemh_irq(unsigned int irq); - -/* - * Initialize IRQ setting - */ -static void __init sh7751systemh_init_irq(void) -{ - make_systemh_irq(0xb); /* Ethernet interrupt */ -} - -static struct sh_machine_vector mv_7751systemh __initmv = { - .mv_name = "7751 SystemH", - .mv_nr_irqs = 72, - - .mv_inb = sh7751systemh_inb, - .mv_inw = sh7751systemh_inw, - .mv_inl = sh7751systemh_inl, - .mv_outb = sh7751systemh_outb, - .mv_outw = sh7751systemh_outw, - .mv_outl = sh7751systemh_outl, - - .mv_inb_p = sh7751systemh_inb_p, - .mv_inw_p = sh7751systemh_inw, - .mv_inl_p = sh7751systemh_inl, - .mv_outb_p = sh7751systemh_outb_p, - .mv_outw_p = sh7751systemh_outw, - .mv_outl_p = sh7751systemh_outl, - - .mv_insb = sh7751systemh_insb, - .mv_insw = sh7751systemh_insw, - .mv_insl = sh7751systemh_insl, - .mv_outsb = sh7751systemh_outsb, - .mv_outsw = sh7751systemh_outsw, - .mv_outsl = sh7751systemh_outsl, - - .mv_init_irq = sh7751systemh_init_irq, -}; |