diff options
Diffstat (limited to 'arch/sh/drivers/pci/pci-sh7780.c')
| -rw-r--r-- | arch/sh/drivers/pci/pci-sh7780.c | 139 |
1 files changed, 139 insertions, 0 deletions
diff --git a/arch/sh/drivers/pci/pci-sh7780.c b/arch/sh/drivers/pci/pci-sh7780.c new file mode 100644 index 000000000000..bd3064a82087 --- /dev/null +++ b/arch/sh/drivers/pci/pci-sh7780.c @@ -0,0 +1,139 @@ +/* + * Low-Level PCI Support for the SH7780 + * + * Dustin McIntire (dustin@sensoria.com) + * Derived from arch/i386/kernel/pci-*.c which bore the message: + * (c) 1999--2000 Martin Mares <mj@ucw.cz> + * + * Ported to the new API by Paul Mundt <lethal@linux-sh.org> + * With cleanup by Paul van Gool <pvangool@mimotech.com> + * + * May be copied or modified under the terms of the GNU General Public + * License. See linux/COPYING for more information. + * + */ + +#undef DEBUG + +#include <linux/config.h> +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/pci.h> +#include <linux/errno.h> +#include <linux/delay.h> +#include "pci-sh4.h" + +/* + * Initialization. Try all known PCI access methods. Note that we support + * using both PCI BIOS and direct access: in such cases, we use I/O ports + * to access config space. + * + * Note that the platform specific initialization (BSC registers, and memory + * space mapping) will be called via the platform defined function + * pcibios_init_platform(). + */ +static int __init sh7780_pci_init(void) +{ + unsigned int id; + int ret; + + pr_debug("PCI: Starting intialization.\n"); + + outl(0x00000001, SH7780_PCI_VCR2); /* Enable PCIC */ + + /* check for SH7780/SH7780R hardware */ + id = pci_read_reg(SH7780_PCIVID); + if ((id != ((SH7780_DEVICE_ID << 16) | SH7780_VENDOR_ID)) && + (id != ((SH7781_DEVICE_ID << 16) | SH7780_VENDOR_ID))) { + printk(KERN_ERR "PCI: This is not an SH7780 (%x)\n", id); + return -ENODEV; + } + + /* Setup the INTC */ + ctrl_outl(0x00200000, INTC_ICR0); /* INTC SH-4 Mode */ + ctrl_outl(0x00078000, INTC_INT2MSKCR); /* enable PCIINTA - PCIINTD */ + ctrl_outl(0x40000000, INTC_INTMSK1); /* disable IRL4-7 Interrupt */ + ctrl_outl(0x0000fffe, INTC_INTMSK2); /* disable IRL4-7 Interrupt */ + ctrl_outl(0x80000000, INTC_INTMSKCLR1); /* enable IRL0-3 Interrupt */ + ctrl_outl(0xfffe0000, INTC_INTMSKCLR2); /* enable IRL0-3 Interrupt */ + + if ((ret = sh4_pci_check_direct()) != 0) + return ret; + + return pcibios_init_platform(); +} +core_initcall(sh7780_pci_init); + +int __init sh7780_pcic_init(struct sh4_pci_address_map *map) +{ + u32 word; + + /* + * This code is unused for some boards as it is done in the + * bootloader and doing it here means the MAC addresses loaded + * by the bootloader get lost. + */ + if (!(map->flags & SH4_PCIC_NO_RESET)) { + /* toggle PCI reset pin */ + word = SH4_PCICR_PREFIX | SH4_PCICR_PRST; + pci_write_reg(word, SH4_PCICR); + /* Wait for a long time... not 1 sec. but long enough */ + mdelay(100); + word = SH4_PCICR_PREFIX; + pci_write_reg(word, SH4_PCICR); + } + + /* set the command/status bits to: + * Wait Cycle Control + Parity Enable + Bus Master + + * Mem space enable + */ + pci_write_reg(0x00000046, SH7780_PCICMD); + + /* define this host as the host bridge */ + word = PCI_BASE_CLASS_BRIDGE << 24; + pci_write_reg(word, SH7780_PCIRID); + + /* Set IO and Mem windows to local address + * Make PCI and local address the same for easy 1 to 1 mapping + * Window0 = map->window0.size @ non-cached area base = SDRAM + * Window1 = map->window1.size @ cached area base = SDRAM + */ + word = ((map->window0.size - 1) & 0x1ff00001) | 0x01; + pci_write_reg(0x07f00001, SH4_PCILSR0); + word = ((map->window1.size - 1) & 0x1ff00001) | 0x01; + pci_write_reg(0x00000001, SH4_PCILSR1); + /* Set the values on window 0 PCI config registers */ + word = P2SEGADDR(map->window0.base); + pci_write_reg(0xa8000000, SH4_PCILAR0); + pci_write_reg(0x08000000, SH7780_PCIMBAR0); + /* Set the values on window 1 PCI config registers */ + word = P2SEGADDR(map->window1.base); + pci_write_reg(0x00000000, SH4_PCILAR1); + pci_write_reg(0x00000000, SH7780_PCIMBAR1); + + /* Map IO space into PCI IO window + * The IO window is 64K-PCIBIOS_MIN_IO in size + * IO addresses will be translated to the + * PCI IO window base address + */ + pr_debug("PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n", + PCIBIOS_MIN_IO, (64 << 10), + SH7780_PCI_IO_BASE + PCIBIOS_MIN_IO); + + /* NOTE: I'm ignoring the PCI error IRQs for now.. + * TODO: add support for the internal error interrupts and + * DMA interrupts... + */ + +#ifdef CONFIG_SH_R7780RP + pci_fixup_pcic(); +#endif + + /* SH7780 init done, set central function init complete */ + /* use round robin mode to stop a device starving/overruning */ + word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_FTO; + pci_write_reg(word, SH4_PCICR); + + return 1; +} |