diff options
Diffstat (limited to 'arch/tile/kernel/setup.c')
| -rw-r--r-- | arch/tile/kernel/setup.c | 42 |
1 files changed, 24 insertions, 18 deletions
diff --git a/arch/tile/kernel/setup.c b/arch/tile/kernel/setup.c index e7d54c73d5c1..fb0b3cbeae14 100644 --- a/arch/tile/kernel/setup.c +++ b/arch/tile/kernel/setup.c @@ -30,8 +30,6 @@ #include <linux/timex.h> #include <asm/setup.h> #include <asm/sections.h> -#include <asm/sections.h> -#include <asm/cacheflush.h> #include <asm/cacheflush.h> #include <asm/pgalloc.h> #include <asm/mmu_context.h> @@ -187,11 +185,11 @@ early_param("vmalloc", parse_vmalloc); #ifdef CONFIG_HIGHMEM /* - * Determine for each controller where its lowmem is mapped and how - * much of it is mapped there. On controller zero, the first few - * megabytes are mapped at 0xfd000000 as code, so in principle we - * could start our data mappings higher up, but for now we don't - * bother, to avoid additional confusion. + * Determine for each controller where its lowmem is mapped and how much of + * it is mapped there. On controller zero, the first few megabytes are + * already mapped in as code at MEM_SV_INTRPT, so in principle we could + * start our data mappings higher up, but for now we don't bother, to avoid + * additional confusion. * * One question is whether, on systems with more than 768 Mb and * controllers of different sizes, to map in a proportionate amount of @@ -311,7 +309,7 @@ static void __init setup_memory(void) #endif /* We are using a char to hold the cpu_2_node[] mapping */ - BUG_ON(MAX_NUMNODES > 127); + BUILD_BUG_ON(MAX_NUMNODES > 127); /* Discover the ranges of memory available to us */ for (i = 0; ; ++i) { @@ -870,11 +868,14 @@ void __cpuinit setup_cpu(int boot) /* Allow asynchronous TLB interrupts. */ #if CHIP_HAS_TILE_DMA() - raw_local_irq_unmask(INT_DMATLB_MISS); - raw_local_irq_unmask(INT_DMATLB_ACCESS); + arch_local_irq_unmask(INT_DMATLB_MISS); + arch_local_irq_unmask(INT_DMATLB_ACCESS); #endif #if CHIP_HAS_SN_PROC() - raw_local_irq_unmask(INT_SNITLB_MISS); + arch_local_irq_unmask(INT_SNITLB_MISS); +#endif +#ifdef __tilegx__ + arch_local_irq_unmask(INT_SINGLE_STEP_K); #endif /* @@ -893,11 +894,12 @@ void __cpuinit setup_cpu(int boot) #endif /* - * Set the MPL for interrupt control 0 to user level. - * This includes access to the SYSTEM_SAVE and EX_CONTEXT SPRs, - * as well as the PL 0 interrupt mask. + * Set the MPL for interrupt control 0 & 1 to the corresponding + * values. This includes access to the SYSTEM_SAVE and EX_CONTEXT + * SPRs, as well as the interrupt mask. */ __insn_mtspr(SPR_MPL_INTCTRL_0_SET_0, 1); + __insn_mtspr(SPR_MPL_INTCTRL_1_SET_1, 1); /* Initialize IRQ support for this cpu. */ setup_irq_regs(); @@ -1033,7 +1035,7 @@ static void __init validate_va(void) * In addition, make sure we CAN'T use the end of memory, since * we use the last chunk of each pgd for the pgd_list. */ - int i, fc_fd_ok = 0; + int i, user_kernel_ok = 0; unsigned long max_va = 0; unsigned long list_va = ((PGD_LIST_OFFSET / sizeof(pgd_t)) << PGDIR_SHIFT); @@ -1044,13 +1046,13 @@ static void __init validate_va(void) break; if (range.start <= MEM_USER_INTRPT && range.start + range.size >= MEM_HV_INTRPT) - fc_fd_ok = 1; + user_kernel_ok = 1; if (range.start == 0) max_va = range.size; BUG_ON(range.start + range.size > list_va); } - if (!fc_fd_ok) - early_panic("Hypervisor not configured for VAs 0xfc/0xfd\n"); + if (!user_kernel_ok) + early_panic("Hypervisor not configured for user/kernel VAs\n"); if (max_va == 0) early_panic("Hypervisor not configured for low VAs\n"); if (max_va < KERNEL_HIGH_VADDR) @@ -1334,6 +1336,10 @@ static void __init pcpu_fc_populate_pte(unsigned long addr) pte_t *pte; BUG_ON(pgd_addr_invalid(addr)); + if (addr < VMALLOC_START || addr >= VMALLOC_END) + panic("PCPU addr %#lx outside vmalloc range %#lx..%#lx;" + " try increasing CONFIG_VMALLOC_RESERVE\n", + addr, VMALLOC_START, VMALLOC_END); pgd = swapper_pg_dir + pgd_index(addr); pud = pud_offset(pgd, addr); |