diff options
Diffstat (limited to 'drivers/ata/sata_nv.c')
| -rw-r--r-- | drivers/ata/sata_nv.c | 62 |
1 files changed, 24 insertions, 38 deletions
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c index 8c683ddd0f58..b6e9ad6d33c9 100644 --- a/drivers/ata/sata_nv.c +++ b/drivers/ata/sata_nv.c @@ -740,32 +740,16 @@ static int nv_adma_slave_config(struct scsi_device *sdev) sdev1 = ap->host->ports[1]->link.device[0].sdev; if ((port0->flags & NV_ADMA_ATAPI_SETUP_COMPLETE) || (port1->flags & NV_ADMA_ATAPI_SETUP_COMPLETE)) { - /** We have to set the DMA mask to 32-bit if either port is in - ATAPI mode, since they are on the same PCI device which is - used for DMA mapping. If we set the mask we also need to set - the bounce limit on both ports to ensure that the block - layer doesn't feed addresses that cause DMA mapping to - choke. If either SCSI device is not allocated yet, it's OK - since that port will discover its correct setting when it - does get allocated. - Note: Setting 32-bit mask should not fail. */ - if (sdev0) - blk_queue_bounce_limit(sdev0->request_queue, - ATA_DMA_MASK); - if (sdev1) - blk_queue_bounce_limit(sdev1->request_queue, - ATA_DMA_MASK); - - dma_set_mask(&pdev->dev, ATA_DMA_MASK); + /* + * We have to set the DMA mask to 32-bit if either port is in + * ATAPI mode, since they are on the same PCI device which is + * used for DMA mapping. If either SCSI device is not allocated + * yet, it's OK since that port will discover its correct + * setting when it does get allocated. + */ + rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK); } else { - /** This shouldn't fail as it was set to this value before */ - dma_set_mask(&pdev->dev, pp->adma_dma_mask); - if (sdev0) - blk_queue_bounce_limit(sdev0->request_queue, - pp->adma_dma_mask); - if (sdev1) - blk_queue_bounce_limit(sdev1->request_queue, - pp->adma_dma_mask); + rc = dma_set_mask(&pdev->dev, pp->adma_dma_mask); } blk_queue_segment_boundary(sdev->request_queue, segment_boundary); @@ -1131,12 +1115,11 @@ static int nv_adma_port_start(struct ata_port *ap) VPRINTK("ENTER\n"); - /* Ensure DMA mask is set to 32-bit before allocating legacy PRD and - pad buffers */ - rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)); - if (rc) - return rc; - rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32)); + /* + * Ensure DMA mask is set to 32-bit before allocating legacy PRD and + * pad buffers. + */ + rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); if (rc) return rc; @@ -1156,13 +1139,16 @@ static int nv_adma_port_start(struct ata_port *ap) pp->notifier_clear_block = pp->gen_block + NV_ADMA_NOTIFIER_CLEAR + (4 * ap->port_no); - /* Now that the legacy PRD and padding buffer are allocated we can - safely raise the DMA mask to allocate the CPB/APRD table. - These are allowed to fail since we store the value that ends up - being used to set as the bounce limit in slave_config later if - needed. */ - dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)); - dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64)); + /* + * Now that the legacy PRD and padding buffer are allocated we can + * try to raise the DMA mask to allocate the CPB/APRD table. + */ + rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); + if (rc) { + rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); + if (rc) + return rc; + } pp->adma_dma_mask = *dev->dma_mask; mem = dmam_alloc_coherent(dev, NV_ADMA_PORT_PRIV_DMA_SZ, |