diff options
Diffstat (limited to 'drivers/bus')
| -rw-r--r-- | drivers/bus/Kconfig | 14 | ||||
| -rw-r--r-- | drivers/bus/Makefile | 1 | ||||
| -rw-r--r-- | drivers/bus/qcom-ebi2.c | 408 | ||||
| -rw-r--r-- | drivers/bus/tegra-aconnect.c | 22 |
4 files changed, 420 insertions, 25 deletions
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig index 3b205e212337..7010dcac9328 100644 --- a/drivers/bus/Kconfig +++ b/drivers/bus/Kconfig @@ -108,6 +108,14 @@ config OMAP_OCP2SCP OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via OCP2SCP. +config QCOM_EBI2 + bool "Qualcomm External Bus Interface 2 (EBI2)" + depends on HAS_IOMEM + help + Say y here to enable support for the Qualcomm External Bus + Interface 2, which can be used to connect things like NAND Flash, + SRAM, ethernet adapters, FPGAs and LCD displays. + config SIMPLE_PM_BUS bool "Simple Power-Managed Bus Driver" depends on OF && PM @@ -132,12 +140,8 @@ config SUNXI_RSB with various RSB based devices, such as AXP223, AXP8XX PMICs, and AC100/AC200 ICs. -# TODO: This uses pm_clk_*() symbols that aren't exported in v4.7 and hence -# the driver will fail to build as a module. However there are patches to -# address that queued for v4.8, so this can be turned into a tristate symbol -# after v4.8-rc1. config TEGRA_ACONNECT - bool "Tegra ACONNECT Bus Driver" + tristate "Tegra ACONNECT Bus Driver" depends on ARCH_TEGRA_210_SOC depends on OF && PM select PM_CLK diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile index ac84cc4348e3..c6cfa6b2606e 100644 --- a/drivers/bus/Makefile +++ b/drivers/bus/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_MVEBU_MBUS) += mvebu-mbus.o obj-$(CONFIG_OMAP_INTERCONNECT) += omap_l3_smx.o omap_l3_noc.o obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o +obj-$(CONFIG_QCOM_EBI2) += qcom-ebi2.o obj-$(CONFIG_SUNXI_RSB) += sunxi-rsb.o obj-$(CONFIG_SIMPLE_PM_BUS) += simple-pm-bus.o obj-$(CONFIG_TEGRA_ACONNECT) += tegra-aconnect.o diff --git a/drivers/bus/qcom-ebi2.c b/drivers/bus/qcom-ebi2.c new file mode 100644 index 000000000000..a6444244c411 --- /dev/null +++ b/drivers/bus/qcom-ebi2.c @@ -0,0 +1,408 @@ +/* + * Qualcomm External Bus Interface 2 (EBI2) driver + * an older version of the Qualcomm Parallel Interface Controller (QPIC) + * + * Copyright (C) 2016 Linaro Ltd. + * + * Author: Linus Walleij <linus.walleij@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2, as + * published by the Free Software Foundation. + * + * See the device tree bindings for this block for more details on the + * hardware. + */ + +#include <linux/module.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/platform_device.h> +#include <linux/bitops.h> + +/* + * CS0, CS1, CS4 and CS5 are two bits wide, CS2 and CS3 are one bit. + */ +#define EBI2_CS0_ENABLE_MASK BIT(0)|BIT(1) +#define EBI2_CS1_ENABLE_MASK BIT(2)|BIT(3) +#define EBI2_CS2_ENABLE_MASK BIT(4) +#define EBI2_CS3_ENABLE_MASK BIT(5) +#define EBI2_CS4_ENABLE_MASK BIT(6)|BIT(7) +#define EBI2_CS5_ENABLE_MASK BIT(8)|BIT(9) +#define EBI2_CSN_MASK GENMASK(9, 0) + +#define EBI2_XMEM_CFG 0x0000 /* Power management etc */ + +/* + * SLOW CSn CFG + * + * Bits 31-28: RECOVERY recovery cycles (0 = 1, 1 = 2 etc) this is the time the + * memory continues to drive the data bus after OE is de-asserted. + * Inserted when reading one CS and switching to another CS or read + * followed by write on the same CS. Valid values 0 thru 15. + * Bits 27-24: WR_HOLD write hold cycles, these are extra cycles inserted after + * every write minimum 1. The data out is driven from the time WE is + * asserted until CS is asserted. With a hold of 1, the CS stays + * active for 1 extra cycle etc. Valid values 0 thru 15. + * Bits 23-16: WR_DELTA initial latency for write cycles inserted for the first + * write to a page or burst memory + * Bits 15-8: RD_DELTA initial latency for read cycles inserted for the first + * read to a page or burst memory + * Bits 7-4: WR_WAIT number of wait cycles for every write access, 0=1 cycle + * so 1 thru 16 cycles. + * Bits 3-0: RD_WAIT number of wait cycles for every read access, 0=1 cycle + * so 1 thru 16 cycles. + */ +#define EBI2_XMEM_CS0_SLOW_CFG 0x0008 +#define EBI2_XMEM_CS1_SLOW_CFG 0x000C +#define EBI2_XMEM_CS2_SLOW_CFG 0x0010 +#define EBI2_XMEM_CS3_SLOW_CFG 0x0014 +#define EBI2_XMEM_CS4_SLOW_CFG 0x0018 +#define EBI2_XMEM_CS5_SLOW_CFG 0x001C + +#define EBI2_XMEM_RECOVERY_SHIFT 28 +#define EBI2_XMEM_WR_HOLD_SHIFT 24 +#define EBI2_XMEM_WR_DELTA_SHIFT 16 +#define EBI2_XMEM_RD_DELTA_SHIFT 8 +#define EBI2_XMEM_WR_WAIT_SHIFT 4 +#define EBI2_XMEM_RD_WAIT_SHIFT 0 + +/* + * FAST CSn CFG + * Bits 31-28: ? + * Bits 27-24: RD_HOLD: the length in cycles of the first segment of a read + * transfer. For a single read trandfer this will be the time + * from CS assertion to OE assertion. + * Bits 18-24: ? + * Bits 17-16: ADV_OE_RECOVERY, the number of cycles elapsed before an OE + * assertion, with respect to the cycle where ADV is asserted. + * 2 means 2 cycles between ADV and OE. Values 0, 1, 2 or 3. + * Bits 5: ADDR_HOLD_ENA, The address is held for an extra cycle to meet + * hold time requirements with ADV assertion. + * + * The manual mentions "write precharge cycles" and "precharge cycles". + * We have not been able to figure out which bit fields these correspond to + * in the hardware, or what valid values exist. The current hypothesis is that + * this is something just used on the FAST chip selects. There is also a "byte + * device enable" flag somewhere for 8bit memories. + */ +#define EBI2_XMEM_CS0_FAST_CFG 0x0028 +#define EBI2_XMEM_CS1_FAST_CFG 0x002C +#define EBI2_XMEM_CS2_FAST_CFG 0x0030 +#define EBI2_XMEM_CS3_FAST_CFG 0x0034 +#define EBI2_XMEM_CS4_FAST_CFG 0x0038 +#define EBI2_XMEM_CS5_FAST_CFG 0x003C + +#define EBI2_XMEM_RD_HOLD_SHIFT 24 +#define EBI2_XMEM_ADV_OE_RECOVERY_SHIFT 16 +#define EBI2_XMEM_ADDR_HOLD_ENA_SHIFT 5 + +/** + * struct cs_data - struct with info on a chipselect setting + * @enable_mask: mask to enable the chipselect in the EBI2 config + * @slow_cfg0: offset to XMEMC slow CS config + * @fast_cfg1: offset to XMEMC fast CS config + */ +struct cs_data { + u32 enable_mask; + u16 slow_cfg; + u16 fast_cfg; +}; + +static const struct cs_data cs_info[] = { + { + /* CS0 */ + .enable_mask = EBI2_CS0_ENABLE_MASK, + .slow_cfg = EBI2_XMEM_CS0_SLOW_CFG, + .fast_cfg = EBI2_XMEM_CS0_FAST_CFG, + }, + { + /* CS1 */ + .enable_mask = EBI2_CS1_ENABLE_MASK, + .slow_cfg = EBI2_XMEM_CS1_SLOW_CFG, + .fast_cfg = EBI2_XMEM_CS1_FAST_CFG, + }, + { + /* CS2 */ + .enable_mask = EBI2_CS2_ENABLE_MASK, + .slow_cfg = EBI2_XMEM_CS2_SLOW_CFG, + .fast_cfg = EBI2_XMEM_CS2_FAST_CFG, + }, + { + /* CS3 */ + .enable_mask = EBI2_CS3_ENABLE_MASK, + .slow_cfg = EBI2_XMEM_CS3_SLOW_CFG, + .fast_cfg = EBI2_XMEM_CS3_FAST_CFG, + }, + { + /* CS4 */ + .enable_mask = EBI2_CS4_ENABLE_MASK, + .slow_cfg = EBI2_XMEM_CS4_SLOW_CFG, + .fast_cfg = EBI2_XMEM_CS4_FAST_CFG, + }, + { + /* CS5 */ + .enable_mask = EBI2_CS5_ENABLE_MASK, + .slow_cfg = EBI2_XMEM_CS5_SLOW_CFG, + .fast_cfg = EBI2_XMEM_CS5_FAST_CFG, + }, +}; + +/** + * struct ebi2_xmem_prop - describes an XMEM config property + * @prop: the device tree binding name + * @max: maximum value for the property + * @slowreg: true if this property is in the SLOW CS config register + * else it is assumed to be in the FAST config register + * @shift: the bit field start in the SLOW or FAST register for this + * property + */ +struct ebi2_xmem_prop { + const char *prop; + u32 max; + bool slowreg; + u16 shift; +}; + +static const struct ebi2_xmem_prop xmem_props[] = { + { + .prop = "qcom,xmem-recovery-cycles", + .max = 15, + .slowreg = true, + .shift = EBI2_XMEM_RECOVERY_SHIFT, + }, + { + .prop = "qcom,xmem-write-hold-cycles", + .max = 15, + .slowreg = true, + .shift = EBI2_XMEM_WR_HOLD_SHIFT, + }, + { + .prop = "qcom,xmem-write-delta-cycles", + .max = 255, + .slowreg = true, + .shift = EBI2_XMEM_WR_DELTA_SHIFT, + }, + { + .prop = "qcom,xmem-read-delta-cycles", + .max = 255, + .slowreg = true, + .shift = EBI2_XMEM_RD_DELTA_SHIFT, + }, + { + .prop = "qcom,xmem-write-wait-cycles", + .max = 15, + .slowreg = true, + .shift = EBI2_XMEM_WR_WAIT_SHIFT, + }, + { + .prop = "qcom,xmem-read-wait-cycles", + .max = 15, + .slowreg = true, + .shift = EBI2_XMEM_RD_WAIT_SHIFT, + }, + { + .prop = "qcom,xmem-address-hold-enable", + .max = 1, /* boolean prop */ + .slowreg = false, + .shift = EBI2_XMEM_ADDR_HOLD_ENA_SHIFT, + }, + { + .prop = "qcom,xmem-adv-to-oe-recovery-cycles", + .max = 3, + .slowreg = false, + .shift = EBI2_XMEM_ADV_OE_RECOVERY_SHIFT, + }, + { + .prop = "qcom,xmem-read-hold-cycles", + .max = 15, + .slowreg = false, + .shift = EBI2_XMEM_RD_HOLD_SHIFT, + }, +}; + +static void qcom_ebi2_setup_chipselect(struct device_node *np, + struct device *dev, + void __iomem *ebi2_base, + void __iomem *ebi2_xmem, + u32 csindex) +{ + const struct cs_data *csd; + u32 slowcfg, fastcfg; + u32 val; + int ret; + int i; + + csd = &cs_info[csindex]; + val = readl(ebi2_base); + val |= csd->enable_mask; + writel(val, ebi2_base); + dev_dbg(dev, "enabled CS%u\n", csindex); + + /* Next set up the XMEMC */ + slowcfg = 0; + fastcfg = 0; + + for (i = 0; i < ARRAY_SIZE(xmem_props); i++) { + const struct ebi2_xmem_prop *xp = &xmem_props[i]; + + /* All are regular u32 values */ + ret = of_property_read_u32(np, xp->prop, &val); + if (ret) { + dev_dbg(dev, "could not read %s for CS%d\n", + xp->prop, csindex); + continue; + } + + /* First check boolean props */ + if (xp->max == 1 && val) { + if (xp->slowreg) + slowcfg |= BIT(xp->shift); + else + fastcfg |= BIT(xp->shift); + dev_dbg(dev, "set %s flag\n", xp->prop); + continue; + } + + /* We're dealing with an u32 */ + if (val > xp->max) { + dev_err(dev, + "too high value for %s: %u, capped at %u\n", + xp->prop, val, xp->max); + val = xp->max; + } + if (xp->slowreg) + slowcfg |= (val << xp->shift); + else + fastcfg |= (val << xp->shift); + dev_dbg(dev, "set %s to %u\n", xp->prop, val); + } + + dev_info(dev, "CS%u: SLOW CFG 0x%08x, FAST CFG 0x%08x\n", + csindex, slowcfg, fastcfg); + + if (slowcfg) + writel(slowcfg, ebi2_xmem + csd->slow_cfg); + if (fastcfg) + writel(fastcfg, ebi2_xmem + csd->fast_cfg); +} + +static int qcom_ebi2_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct device_node *child; + struct device *dev = &pdev->dev; + struct resource *res; + void __iomem *ebi2_base; + void __iomem *ebi2_xmem; + struct clk *ebi2xclk; + struct clk *ebi2clk; + bool have_children = false; + u32 val; + int ret; + + ebi2xclk = devm_clk_get(dev, "ebi2x"); + if (IS_ERR(ebi2xclk)) + return PTR_ERR(ebi2xclk); + + ret = clk_prepare_enable(ebi2xclk); + if (ret) { + dev_err(dev, "could not enable EBI2X clk (%d)\n", ret); + return ret; + } + + ebi2clk = devm_clk_get(dev, "ebi2"); + if (IS_ERR(ebi2clk)) { + ret = PTR_ERR(ebi2clk); + goto err_disable_2x_clk; + } + + ret = clk_prepare_enable(ebi2clk); + if (ret) { + dev_err(dev, "could not enable EBI2 clk\n"); + goto err_disable_2x_clk; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + ebi2_base = devm_ioremap_resource(dev, res); + if (IS_ERR(ebi2_base)) { + ret = PTR_ERR(ebi2_base); + goto err_disable_clk; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + ebi2_xmem = devm_ioremap_resource(dev, res); + if (IS_ERR(ebi2_xmem)) { + ret = PTR_ERR(ebi2_xmem); + goto err_disable_clk; + } + + /* Allegedly this turns the power save mode off */ + writel(0UL, ebi2_xmem + EBI2_XMEM_CFG); + + /* Disable all chipselects */ + val = readl(ebi2_base); + val &= ~EBI2_CSN_MASK; + writel(val, ebi2_base); + + /* Walk over the child nodes and see what chipselects we use */ + for_each_available_child_of_node(np, child) { + u32 csindex; + + /* Figure out the chipselect */ + ret = of_property_read_u32(child, "reg", &csindex); + if (ret) + return ret; + + if (csindex > 5) { + dev_err(dev, + "invalid chipselect %u, we only support 0-5\n", + csindex); + continue; + } + + qcom_ebi2_setup_chipselect(child, + dev, + ebi2_base, + ebi2_xmem, + csindex); + + /* We have at least one child */ + have_children = true; + } + + if (have_children) + return of_platform_default_populate(np, NULL, dev); + return 0; + +err_disable_clk: + clk_disable_unprepare(ebi2clk); +err_disable_2x_clk: + clk_disable_unprepare(ebi2xclk); + + return ret; +} + +static const struct of_device_id qcom_ebi2_of_match[] = { + { .compatible = "qcom,msm8660-ebi2", }, + { .compatible = "qcom,apq8060-ebi2", }, + { } +}; + +static struct platform_driver qcom_ebi2_driver = { + .probe = qcom_ebi2_probe, + .driver = { + .name = "qcom-ebi2", + .of_match_table = qcom_ebi2_of_match, + }, +}; +module_platform_driver(qcom_ebi2_driver); +MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>"); +MODULE_DESCRIPTION("Qualcomm EBI2 driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/bus/tegra-aconnect.c b/drivers/bus/tegra-aconnect.c index 7e4104b74fa8..084ae286fa23 100644 --- a/drivers/bus/tegra-aconnect.c +++ b/drivers/bus/tegra-aconnect.c @@ -15,24 +15,6 @@ #include <linux/pm_clock.h> #include <linux/pm_runtime.h> -static int tegra_aconnect_add_clock(struct device *dev, char *name) -{ - struct clk *clk; - int ret; - - clk = clk_get(dev, name); - if (IS_ERR(clk)) { - dev_err(dev, "%s clock not found\n", name); - return PTR_ERR(clk); - } - - ret = pm_clk_add_clk(dev, clk); - if (ret) - clk_put(clk); - - return ret; -} - static int tegra_aconnect_probe(struct platform_device *pdev) { int ret; @@ -44,11 +26,11 @@ static int tegra_aconnect_probe(struct platform_device *pdev) if (ret) return ret; - ret = tegra_aconnect_add_clock(&pdev->dev, "ape"); + ret = of_pm_clk_add_clk(&pdev->dev, "ape"); if (ret) goto clk_destroy; - ret = tegra_aconnect_add_clock(&pdev->dev, "apb2ape"); + ret = of_pm_clk_add_clk(&pdev->dev, "apb2ape"); if (ret) goto clk_destroy; |