summaryrefslogtreecommitdiffstats
path: root/drivers/bus
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/bus')
-rw-r--r--drivers/bus/Kconfig8
-rw-r--r--drivers/bus/Makefile1
-rw-r--r--drivers/bus/omap-ocp2scp.c2
-rw-r--r--drivers/bus/sunxi-rsb.c8
-rw-r--r--drivers/bus/uniphier-system-bus.c281
-rw-r--r--drivers/bus/vexpress-config.c4
6 files changed, 298 insertions, 6 deletions
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index 116b363b7987..9a92c072a485 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -131,6 +131,14 @@ config SUNXI_RSB
with various RSB based devices, such as AXP223, AXP8XX PMICs,
and AC100/AC200 ICs.
+config UNIPHIER_SYSTEM_BUS
+ tristate "UniPhier System Bus driver"
+ depends on ARCH_UNIPHIER && OF
+ default y
+ help
+ Support for UniPhier System Bus, a simple external bus. This is
+ needed to use on-board devices connected to UniPhier SoCs.
+
config VEXPRESS_CONFIG
bool "Versatile Express configuration bus"
default y if ARCH_VEXPRESS
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index fcb9f9794a1f..ccff007ee7e8 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -17,4 +17,5 @@ obj-$(CONFIG_OMAP_INTERCONNECT) += omap_l3_smx.o omap_l3_noc.o
obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o
obj-$(CONFIG_SUNXI_RSB) += sunxi-rsb.o
obj-$(CONFIG_SIMPLE_PM_BUS) += simple-pm-bus.o
+obj-$(CONFIG_UNIPHIER_SYSTEM_BUS) += uniphier-system-bus.o
obj-$(CONFIG_VEXPRESS_CONFIG) += vexpress-config.o
diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
index 9f1856948758..bf500e0e7362 100644
--- a/drivers/bus/omap-ocp2scp.c
+++ b/drivers/bus/omap-ocp2scp.c
@@ -117,7 +117,7 @@ static struct platform_driver omap_ocp2scp_driver = {
module_platform_driver(omap_ocp2scp_driver);
-MODULE_ALIAS("platform: omap-ocp2scp");
+MODULE_ALIAS("platform:omap-ocp2scp");
MODULE_AUTHOR("Texas Instruments Inc.");
MODULE_DESCRIPTION("OMAP OCP2SCP driver");
MODULE_LICENSE("GPL v2");
diff --git a/drivers/bus/sunxi-rsb.c b/drivers/bus/sunxi-rsb.c
index 846bc29c157d..25996e256110 100644
--- a/drivers/bus/sunxi-rsb.c
+++ b/drivers/bus/sunxi-rsb.c
@@ -342,13 +342,13 @@ static int sunxi_rsb_read(struct sunxi_rsb *rsb, u8 rtaddr, u8 addr,
ret = _sunxi_rsb_run_xfer(rsb);
if (ret)
- goto out;
+ goto unlock;
*buf = readl(rsb->regs + RSB_DATA);
+unlock:
mutex_unlock(&rsb->lock);
-out:
return ret;
}
@@ -527,9 +527,9 @@ static int sunxi_rsb_init_device_mode(struct sunxi_rsb *rsb)
*/
static const struct sunxi_rsb_addr_map sunxi_rsb_addr_maps[] = {
- { 0x3e3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */
+ { 0x3a3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */
{ 0x745, 0x3a }, /* Secondary PMIC: AXP806, ... */
- { 0xe89, 0x45 }, /* Peripheral IC: AC100, ... */
+ { 0xe89, 0x4e }, /* Peripheral IC: AC100, ... */
};
static u8 sunxi_rsb_get_rtaddr(u16 hwaddr)
diff --git a/drivers/bus/uniphier-system-bus.c b/drivers/bus/uniphier-system-bus.c
new file mode 100644
index 000000000000..834a2aeaf27a
--- /dev/null
+++ b/drivers/bus/uniphier-system-bus.c
@@ -0,0 +1,281 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/log2.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+/* System Bus Controller registers */
+#define UNIPHIER_SBC_BASE 0x100 /* base address of bank0 space */
+#define UNIPHIER_SBC_BASE_BE BIT(0) /* bank_enable */
+#define UNIPHIER_SBC_CTRL0 0x200 /* timing parameter 0 of bank0 */
+#define UNIPHIER_SBC_CTRL1 0x204 /* timing parameter 1 of bank0 */
+#define UNIPHIER_SBC_CTRL2 0x208 /* timing parameter 2 of bank0 */
+#define UNIPHIER_SBC_CTRL3 0x20c /* timing parameter 3 of bank0 */
+#define UNIPHIER_SBC_CTRL4 0x300 /* timing parameter 4 of bank0 */
+
+#define UNIPHIER_SBC_STRIDE 0x10 /* register stride to next bank */
+#define UNIPHIER_SBC_NR_BANKS 8 /* number of banks (chip select) */
+#define UNIPHIER_SBC_BASE_DUMMY 0xffffffff /* data to squash bank 0, 1 */
+
+struct uniphier_system_bus_bank {
+ u32 base;
+ u32 end;
+};
+
+struct uniphier_system_bus_priv {
+ struct device *dev;
+ void __iomem *membase;
+ struct uniphier_system_bus_bank bank[UNIPHIER_SBC_NR_BANKS];
+};
+
+static int uniphier_system_bus_add_bank(struct uniphier_system_bus_priv *priv,
+ int bank, u32 addr, u64 paddr, u32 size)
+{
+ u64 end, mask;
+
+ dev_dbg(priv->dev,
+ "range found: bank = %d, addr = %08x, paddr = %08llx, size = %08x\n",
+ bank, addr, paddr, size);
+
+ if (bank >= ARRAY_SIZE(priv->bank)) {
+ dev_err(priv->dev, "unsupported bank number %d\n", bank);
+ return -EINVAL;
+ }
+
+ if (priv->bank[bank].base || priv->bank[bank].end) {
+ dev_err(priv->dev,
+ "range for bank %d has already been specified\n", bank);
+ return -EINVAL;
+ }
+
+ if (paddr > U32_MAX) {
+ dev_err(priv->dev, "base address %llx is too high\n", paddr);
+ return -EINVAL;
+ }
+
+ end = paddr + size;
+
+ if (addr > paddr) {
+ dev_err(priv->dev,
+ "base %08x cannot be mapped to %08llx of parent\n",
+ addr, paddr);
+ return -EINVAL;
+ }
+ paddr -= addr;
+
+ paddr = round_down(paddr, 0x00020000);
+ end = round_up(end, 0x00020000);
+
+ if (end > U32_MAX) {
+ dev_err(priv->dev, "end address %08llx is too high\n", end);
+ return -EINVAL;
+ }
+ mask = paddr ^ (end - 1);
+ mask = roundup_pow_of_two(mask);
+
+ paddr = round_down(paddr, mask);
+ end = round_up(end, mask);
+
+ priv->bank[bank].base = paddr;
+ priv->bank[bank].end = end;
+
+ dev_dbg(priv->dev, "range added: bank = %d, addr = %08x, end = %08x\n",
+ bank, priv->bank[bank].base, priv->bank[bank].end);
+
+ return 0;
+}
+
+static int uniphier_system_bus_check_overlap(
+ const struct uniphier_system_bus_priv *priv)
+{
+ int i, j;
+
+ for (i = 0; i < ARRAY_SIZE(priv->bank); i++) {
+ for (j = i + 1; j < ARRAY_SIZE(priv->bank); j++) {
+ if (priv->bank[i].end > priv->bank[j].base ||
+ priv->bank[i].base < priv->bank[j].end) {
+ dev_err(priv->dev,
+ "region overlap between bank%d and bank%d\n",
+ i, j);
+ return -EINVAL;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static void uniphier_system_bus_check_boot_swap(
+ struct uniphier_system_bus_priv *priv)
+{
+ void __iomem *base_reg = priv->membase + UNIPHIER_SBC_BASE;
+ int is_swapped;
+
+ is_swapped = !(readl(base_reg) & UNIPHIER_SBC_BASE_BE);
+
+ dev_dbg(priv->dev, "Boot Swap: %s\n", is_swapped ? "on" : "off");
+
+ /*
+ * If BOOT_SWAP was asserted on power-on-reset, the CS0 and CS1 are
+ * swapped. In this case, bank0 and bank1 should be swapped as well.
+ */
+ if (is_swapped)
+ swap(priv->bank[0], priv->bank[1]);
+}
+
+static void uniphier_system_bus_set_reg(
+ const struct uniphier_system_bus_priv *priv)
+{
+ void __iomem *base_reg = priv->membase + UNIPHIER_SBC_BASE;
+ u32 base, end, mask, val;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(priv->bank); i++) {
+ base = priv->bank[i].base;
+ end = priv->bank[i].end;
+
+ if (base == end) {
+ /*
+ * If SBC_BASE0 or SBC_BASE1 is set to zero, the access
+ * to anywhere in the system bus space is routed to
+ * bank 0 (if boot swap if off) or bank 1 (if boot swap
+ * if on). It means that CPUs cannot get access to
+ * bank 2 or later. In other words, bank 0/1 cannot
+ * be disabled even if its bank_enable bits is cleared.
+ * This seems odd, but it is how this hardware goes.
+ * As a workaround, dummy data (0xffffffff) should be
+ * set when the bank 0/1 is unused. As for bank 2 and
+ * later, they can be simply disable by clearing the
+ * bank_enable bit.
+ */
+ if (i < 2)
+ val = UNIPHIER_SBC_BASE_DUMMY;
+ else
+ val = 0;
+ } else {
+ mask = base ^ (end - 1);
+
+ val = base & 0xfffe0000;
+ val |= (~mask >> 16) & 0xfffe;
+ val |= UNIPHIER_SBC_BASE_BE;
+ }
+ dev_dbg(priv->dev, "SBC_BASE[%d] = 0x%08x\n", i, val);
+
+ writel(val, base_reg + UNIPHIER_SBC_STRIDE * i);
+ }
+}
+
+static int uniphier_system_bus_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct uniphier_system_bus_priv *priv;
+ struct resource *regs;
+ const __be32 *ranges;
+ u32 cells, addr, size;
+ u64 paddr;
+ int pna, bank, rlen, rone, ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->membase = devm_ioremap_resource(dev, regs);
+ if (IS_ERR(priv->membase))
+ return PTR_ERR(priv->membase);
+
+ priv->dev = dev;
+
+ pna = of_n_addr_cells(dev->of_node);
+
+ ret = of_property_read_u32(dev->of_node, "#address-cells", &cells);
+ if (ret) {
+ dev_err(dev, "failed to get #address-cells\n");
+ return ret;
+ }
+ if (cells != 2) {
+ dev_err(dev, "#address-cells must be 2\n");
+ return -EINVAL;
+ }
+
+ ret = of_property_read_u32(dev->of_node, "#size-cells", &cells);
+ if (ret) {
+ dev_err(dev, "failed to get #size-cells\n");
+ return ret;
+ }
+ if (cells != 1) {
+ dev_err(dev, "#size-cells must be 1\n");
+ return -EINVAL;
+ }
+
+ ranges = of_get_property(dev->of_node, "ranges", &rlen);
+ if (!ranges) {
+ dev_err(dev, "failed to get ranges property\n");
+ return -ENOENT;
+ }
+
+ rlen /= sizeof(*ranges);
+ rone = pna + 2;
+
+ for (; rlen >= rone; rlen -= rone) {
+ bank = be32_to_cpup(ranges++);
+ addr = be32_to_cpup(ranges++);
+ paddr = of_translate_address(dev->of_node, ranges);
+ if (paddr == OF_BAD_ADDR)
+ return -EINVAL;
+ ranges += pna;
+ size = be32_to_cpup(ranges++);
+
+ ret = uniphier_system_bus_add_bank(priv, bank, addr,
+ paddr, size);
+ if (ret)
+ return ret;
+ }
+
+ ret = uniphier_system_bus_check_overlap(priv);
+ if (ret)
+ return ret;
+
+ uniphier_system_bus_check_boot_swap(priv);
+
+ uniphier_system_bus_set_reg(priv);
+
+ /* Now, the bus is configured. Populate platform_devices below it */
+ return of_platform_populate(dev->of_node, of_default_bus_match_table,
+ NULL, dev);
+}
+
+static const struct of_device_id uniphier_system_bus_match[] = {
+ { .compatible = "socionext,uniphier-system-bus" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, uniphier_system_bus_match);
+
+static struct platform_driver uniphier_system_bus_driver = {
+ .probe = uniphier_system_bus_probe,
+ .driver = {
+ .name = "uniphier-system-bus",
+ .of_match_table = uniphier_system_bus_match,
+ },
+};
+module_platform_driver(uniphier_system_bus_driver);
+
+MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
+MODULE_DESCRIPTION("UniPhier System Bus driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/bus/vexpress-config.c b/drivers/bus/vexpress-config.c
index 6575c0fe6a4e..c3cb76b363c6 100644
--- a/drivers/bus/vexpress-config.c
+++ b/drivers/bus/vexpress-config.c
@@ -192,8 +192,10 @@ static int __init vexpress_config_init(void)
/* Need the config devices early, before the "normal" devices... */
for_each_compatible_node(node, NULL, "arm,vexpress,config-bus") {
err = vexpress_config_populate(node);
- if (err)
+ if (err) {
+ of_node_put(node);
break;
+ }
}
return err;
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-12 06:51:00 +0100