diff options
Diffstat (limited to 'drivers/firmware/ti_sci.h')
| -rw-r--r-- | drivers/firmware/ti_sci.h | 492 |
1 files changed, 492 insertions, 0 deletions
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h new file mode 100644 index 000000000000..9b611e9e6f6d --- /dev/null +++ b/drivers/firmware/ti_sci.h @@ -0,0 +1,492 @@ +/* + * Texas Instruments System Control Interface (TISCI) Protocol + * + * Communication protocol with TI SCI hardware + * The system works in a message response protocol + * See: http://processors.wiki.ti.com/index.php/TISCI for details + * + * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/ + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * + * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the + * distribution. + * + * Neither the name of Texas Instruments Incorporated nor the names of + * its contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef __TI_SCI_H +#define __TI_SCI_H + +/* Generic Messages */ +#define TI_SCI_MSG_ENABLE_WDT 0x0000 +#define TI_SCI_MSG_WAKE_RESET 0x0001 +#define TI_SCI_MSG_VERSION 0x0002 +#define TI_SCI_MSG_WAKE_REASON 0x0003 +#define TI_SCI_MSG_GOODBYE 0x0004 +#define TI_SCI_MSG_SYS_RESET 0x0005 + +/* Device requests */ +#define TI_SCI_MSG_SET_DEVICE_STATE 0x0200 +#define TI_SCI_MSG_GET_DEVICE_STATE 0x0201 +#define TI_SCI_MSG_SET_DEVICE_RESETS 0x0202 + +/* Clock requests */ +#define TI_SCI_MSG_SET_CLOCK_STATE 0x0100 +#define TI_SCI_MSG_GET_CLOCK_STATE 0x0101 +#define TI_SCI_MSG_SET_CLOCK_PARENT 0x0102 +#define TI_SCI_MSG_GET_CLOCK_PARENT 0x0103 +#define TI_SCI_MSG_GET_NUM_CLOCK_PARENTS 0x0104 +#define TI_SCI_MSG_SET_CLOCK_FREQ 0x010c +#define TI_SCI_MSG_QUERY_CLOCK_FREQ 0x010d +#define TI_SCI_MSG_GET_CLOCK_FREQ 0x010e + +/** + * struct ti_sci_msg_hdr - Generic Message Header for All messages and responses + * @type: Type of messages: One of TI_SCI_MSG* values + * @host: Host of the message + * @seq: Message identifier indicating a transfer sequence + * @flags: Flag for the message + */ +struct ti_sci_msg_hdr { + u16 type; + u8 host; + u8 seq; +#define TI_SCI_MSG_FLAG(val) (1 << (val)) +#define TI_SCI_FLAG_REQ_GENERIC_NORESPONSE 0x0 +#define TI_SCI_FLAG_REQ_ACK_ON_RECEIVED TI_SCI_MSG_FLAG(0) +#define TI_SCI_FLAG_REQ_ACK_ON_PROCESSED TI_SCI_MSG_FLAG(1) +#define TI_SCI_FLAG_RESP_GENERIC_NACK 0x0 +#define TI_SCI_FLAG_RESP_GENERIC_ACK TI_SCI_MSG_FLAG(1) + /* Additional Flags */ + u32 flags; +} __packed; + +/** + * struct ti_sci_msg_resp_version - Response for a message + * @hdr: Generic header + * @firmware_description: String describing the firmware + * @firmware_revision: Firmware revision + * @abi_major: Major version of the ABI that firmware supports + * @abi_minor: Minor version of the ABI that firmware supports + * + * In general, ABI version changes follow the rule that minor version increments + * are backward compatible. Major revision changes in ABI may not be + * backward compatible. + * + * Response to a generic message with message type TI_SCI_MSG_VERSION + */ +struct ti_sci_msg_resp_version { + struct ti_sci_msg_hdr hdr; + char firmware_description[32]; + u16 firmware_revision; + u8 abi_major; + u8 abi_minor; +} __packed; + +/** + * struct ti_sci_msg_req_reboot - Reboot the SoC + * @hdr: Generic Header + * + * Request type is TI_SCI_MSG_SYS_RESET, responded with a generic + * ACK/NACK message. + */ +struct ti_sci_msg_req_reboot { + struct ti_sci_msg_hdr hdr; +} __packed; + +/** + * struct ti_sci_msg_req_set_device_state - Set the desired state of the device + * @hdr: Generic header + * @id: Indicates which device to modify + * @reserved: Reserved space in message, must be 0 for backward compatibility + * @state: The desired state of the device. + * + * Certain flags can also be set to alter the device state: + * + MSG_FLAG_DEVICE_WAKE_ENABLED - Configure the device to be a wake source. + * The meaning of this flag will vary slightly from device to device and from + * SoC to SoC but it generally allows the device to wake the SoC out of deep + * suspend states. + * + MSG_FLAG_DEVICE_RESET_ISO - Enable reset isolation for this device. + * + MSG_FLAG_DEVICE_EXCLUSIVE - Claim this device exclusively. When passed + * with STATE_RETENTION or STATE_ON, it will claim the device exclusively. + * If another host already has this device set to STATE_RETENTION or STATE_ON, + * the message will fail. Once successful, other hosts attempting to set + * STATE_RETENTION or STATE_ON will fail. + * + * Request type is TI_SCI_MSG_SET_DEVICE_STATE, responded with a generic + * ACK/NACK message. + */ +struct ti_sci_msg_req_set_device_state { + /* Additional hdr->flags options */ +#define MSG_FLAG_DEVICE_WAKE_ENABLED TI_SCI_MSG_FLAG(8) +#define MSG_FLAG_DEVICE_RESET_ISO TI_SCI_MSG_FLAG(9) +#define MSG_FLAG_DEVICE_EXCLUSIVE TI_SCI_MSG_FLAG(10) + struct ti_sci_msg_hdr hdr; + u32 id; + u32 reserved; + +#define MSG_DEVICE_SW_STATE_AUTO_OFF 0 +#define MSG_DEVICE_SW_STATE_RETENTION 1 +#define MSG_DEVICE_SW_STATE_ON 2 + u8 state; +} __packed; + +/** + * struct ti_sci_msg_req_get_device_state - Request to get device. + * @hdr: Generic header + * @id: Device Identifier + * + * Request type is TI_SCI_MSG_GET_DEVICE_STATE, responded device state + * information + */ +struct ti_sci_msg_req_get_device_state { + struct ti_sci_msg_hdr hdr; + u32 id; +} __packed; + +/** + * struct ti_sci_msg_resp_get_device_state - Response to get device request. + * @hdr: Generic header + * @context_loss_count: Indicates how many times the device has lost context. A + * driver can use this monotonic counter to determine if the device has + * lost context since the last time this message was exchanged. + * @resets: Programmed state of the reset lines. + * @programmed_state: The state as programmed by set_device. + * - Uses the MSG_DEVICE_SW_* macros + * @current_state: The actual state of the hardware. + * + * Response to request TI_SCI_MSG_GET_DEVICE_STATE. + */ +struct ti_sci_msg_resp_get_device_state { + struct ti_sci_msg_hdr hdr; + u32 context_loss_count; + u32 resets; + u8 programmed_state; +#define MSG_DEVICE_HW_STATE_OFF 0 +#define MSG_DEVICE_HW_STATE_ON 1 +#define MSG_DEVICE_HW_STATE_TRANS 2 + u8 current_state; +} __packed; + +/** + * struct ti_sci_msg_req_set_device_resets - Set the desired resets + * configuration of the device + * @hdr: Generic header + * @id: Indicates which device to modify + * @resets: A bit field of resets for the device. The meaning, behavior, + * and usage of the reset flags are device specific. 0 for a bit + * indicates releasing the reset represented by that bit while 1 + * indicates keeping it held. + * + * Request type is TI_SCI_MSG_SET_DEVICE_RESETS, responded with a generic + * ACK/NACK message. + */ +struct ti_sci_msg_req_set_device_resets { + struct ti_sci_msg_hdr hdr; + u32 id; + u32 resets; +} __packed; + +/** + * struct ti_sci_msg_req_set_clock_state - Request to setup a Clock state + * @hdr: Generic Header, Certain flags can be set specific to the clocks: + * MSG_FLAG_CLOCK_ALLOW_SSC: Allow this clock to be modified + * via spread spectrum clocking. + * MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE: Allow this clock's + * frequency to be changed while it is running so long as it + * is within the min/max limits. + * MSG_FLAG_CLOCK_INPUT_TERM: Enable input termination, this + * is only applicable to clock inputs on the SoC pseudo-device. + * @dev_id: Device identifier this request is for + * @clk_id: Clock identifier for the device for this request. + * Each device has it's own set of clock inputs. This indexes + * which clock input to modify. + * @request_state: Request the state for the clock to be set to. + * MSG_CLOCK_SW_STATE_UNREQ: The IP does not require this clock, + * it can be disabled, regardless of the state of the device + * MSG_CLOCK_SW_STATE_AUTO: Allow the System Controller to + * automatically manage the state of this clock. If the device + * is enabled, then the clock is enabled. If the device is set + * to off or retention, then the clock is internally set as not + * being required by the device.(default) + * MSG_CLOCK_SW_STATE_REQ: Configure the clock to be enabled, + * regardless of the state of the device. + * + * Normally, all required clocks are managed by TISCI entity, this is used + * only for specific control *IF* required. Auto managed state is + * MSG_CLOCK_SW_STATE_AUTO, in other states, TISCI entity assume remote + * will explicitly control. + * + * Request type is TI_SCI_MSG_SET_CLOCK_STATE, response is a generic + * ACK or NACK message. + */ +struct ti_sci_msg_req_set_clock_state { + /* Additional hdr->flags options */ +#define MSG_FLAG_CLOCK_ALLOW_SSC TI_SCI_MSG_FLAG(8) +#define MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE TI_SCI_MSG_FLAG(9) +#define MSG_FLAG_CLOCK_INPUT_TERM TI_SCI_MSG_FLAG(10) + struct ti_sci_msg_hdr hdr; + u32 dev_id; + u8 clk_id; +#define MSG_CLOCK_SW_STATE_UNREQ 0 +#define MSG_CLOCK_SW_STATE_AUTO 1 +#define MSG_CLOCK_SW_STATE_REQ 2 + u8 request_state; +} __packed; + +/** + * struct ti_sci_msg_req_get_clock_state - Request for clock state + * @hdr: Generic Header + * @dev_id: Device identifier this request is for + * @clk_id: Clock identifier for the device for this request. + * Each device has it's own set of clock inputs. This indexes + * which clock input to get state of. + * + * Request type is TI_SCI_MSG_GET_CLOCK_STATE, response is state + * of the clock + */ +struct ti_sci_msg_req_get_clock_state { + struct ti_sci_msg_hdr hdr; + u32 dev_id; + u8 clk_id; +} __packed; + +/** + * struct ti_sci_msg_resp_get_clock_state - Response to get clock state + * @hdr: Generic Header + * @programmed_state: Any programmed state of the clock. This is one of + * MSG_CLOCK_SW_STATE* values. + * @current_state: Current state of the clock. This is one of: + * MSG_CLOCK_HW_STATE_NOT_READY: Clock is not ready + * MSG_CLOCK_HW_STATE_READY: Clock is ready + * + * Response to TI_SCI_MSG_GET_CLOCK_STATE. + */ +struct ti_sci_msg_resp_get_clock_state { + struct ti_sci_msg_hdr hdr; + u8 programmed_state; +#define MSG_CLOCK_HW_STATE_NOT_READY 0 +#define MSG_CLOCK_HW_STATE_READY 1 + u8 current_state; +} __packed; + +/** + * struct ti_sci_msg_req_set_clock_parent - Set the clock parent + * @hdr: Generic Header + * @dev_id: Device identifier this request is for + * @clk_id: Clock identifier for the device for this request. + * Each device has it's own set of clock inputs. This indexes + * which clock input to modify. + * @parent_id: The new clock parent is selectable by an index via this + * parameter. + * + * Request type is TI_SCI_MSG_SET_CLOCK_PARENT, response is generic + * ACK / NACK message. + */ +struct ti_sci_msg_req_set_clock_parent { + struct ti_sci_msg_hdr hdr; + u32 dev_id; + u8 clk_id; + u8 parent_id; +} __packed; + +/** + * struct ti_sci_msg_req_get_clock_parent - Get the clock parent + * @hdr: Generic Header + * @dev_id: Device identifier this request is for + * @clk_id: Clock identifier for the device for this request. + * Each device has it's own set of clock inputs. This indexes + * which clock input to get the parent for. + * + * Request type is TI_SCI_MSG_GET_CLOCK_PARENT, response is parent information + */ +struct ti_sci_msg_req_get_clock_parent { + struct ti_sci_msg_hdr hdr; + u32 dev_id; + u8 clk_id; +} __packed; + +/** + * struct ti_sci_msg_resp_get_clock_parent - Response with clock parent + * @hdr: Generic Header + * @parent_id: The current clock parent + * + * Response to TI_SCI_MSG_GET_CLOCK_PARENT. + */ +struct ti_sci_msg_resp_get_clock_parent { + struct ti_sci_msg_hdr hdr; + u8 parent_id; +} __packed; + +/** + * struct ti_sci_msg_req_get_clock_num_parents - Request to get clock parents + * @hdr: Generic header + * @dev_id: Device identifier this request is for + * @clk_id: Clock identifier for the device for this request. + * + * This request provides information about how many clock parent options + * are available for a given clock to a device. This is typically used + * for input clocks. + * + * Request type is TI_SCI_MSG_GET_NUM_CLOCK_PARENTS, response is appropriate + * message, or NACK in case of inability to satisfy request. + */ +struct ti_sci_msg_req_get_clock_num_parents { + struct ti_sci_msg_hdr hdr; + u32 dev_id; + u8 clk_id; +} __packed; + +/** + * struct ti_sci_msg_resp_get_clock_num_parents - Response for get clk parents + * @hdr: Generic header + * @num_parents: Number of clock parents + * + * Response to TI_SCI_MSG_GET_NUM_CLOCK_PARENTS + */ +struct ti_sci_msg_resp_get_clock_num_parents { + struct ti_sci_msg_hdr hdr; + u8 num_parents; +} __packed; + +/** + * struct ti_sci_msg_req_query_clock_freq - Request to query a frequency + * @hdr: Generic Header + * @dev_id: Device identifier this request is for + * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum + * allowable programmed frequency and does not account for clock + * tolerances and jitter. + * @target_freq_hz: The target clock frequency. A frequency will be found + * as close to this target frequency as possible. + * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum + * allowable programmed frequency and does not account for clock + * tolerances and jitter. + * @clk_id: Clock identifier for the device for this request. + * + * NOTE: Normally clock frequency management is automatically done by TISCI + * entity. In case of specific requests, TISCI evaluates capability to achieve + * requested frequency within provided range and responds with + * result message. + * + * Request type is TI_SCI_MSG_QUERY_CLOCK_FREQ, response is appropriate message, + * or NACK in case of inability to satisfy request. + */ +struct ti_sci_msg_req_query_clock_freq { + struct ti_sci_msg_hdr hdr; + u32 dev_id; + u64 min_freq_hz; + u64 target_freq_hz; + u64 max_freq_hz; + u8 clk_id; +} __packed; + +/** + * struct ti_sci_msg_resp_query_clock_freq - Response to a clock frequency query + * @hdr: Generic Header + * @freq_hz: Frequency that is the best match in Hz. + * + * Response to request type TI_SCI_MSG_QUERY_CLOCK_FREQ. NOTE: if the request + * cannot be satisfied, the message will be of type NACK. + */ +struct ti_sci_msg_resp_query_clock_freq { + struct ti_sci_msg_hdr hdr; + u64 freq_hz; +} __packed; + +/** + * struct ti_sci_msg_req_set_clock_freq - Request to setup a clock frequency + * @hdr: Generic Header + * @dev_id: Device identifier this request is for + * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum + * allowable programmed frequency and does not account for clock + * tolerances and jitter. + * @target_freq_hz: The target clock frequency. The clock will be programmed + * at a rate as close to this target frequency as possible. + * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum + * allowable programmed frequency and does not account for clock + * tolerances and jitter. + * @clk_id: Clock identifier for the device for this request. + * + * NOTE: Normally clock frequency management is automatically done by TISCI + * entity. In case of specific requests, TISCI evaluates capability to achieve + * requested range and responds with success/failure message. + * + * This sets the desired frequency for a clock within an allowable + * range. This message will fail on an enabled clock unless + * MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE is set for the clock. Additionally, + * if other clocks have their frequency modified due to this message, + * they also must have the MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE or be disabled. + * + * Calling set frequency on a clock input to the SoC pseudo-device will + * inform the PMMC of that clock's frequency. Setting a frequency of + * zero will indicate the clock is disabled. + * + * Calling set frequency on clock outputs from the SoC pseudo-device will + * function similarly to setting the clock frequency on a device. + * + * Request type is TI_SCI_MSG_SET_CLOCK_FREQ, response is a generic ACK/NACK + * message. + */ +struct ti_sci_msg_req_set_clock_freq { + struct ti_sci_msg_hdr hdr; + u32 dev_id; + u64 min_freq_hz; + u64 target_freq_hz; + u64 max_freq_hz; + u8 clk_id; +} __packed; + +/** + * struct ti_sci_msg_req_get_clock_freq - Request to get the clock frequency + * @hdr: Generic Header + * @dev_id: Device identifier this request is for + * @clk_id: Clock identifier for the device for this request. + * + * NOTE: Normally clock frequency management is automatically done by TISCI + * entity. In some cases, clock frequencies are configured by host. + * + * Request type is TI_SCI_MSG_GET_CLOCK_FREQ, responded with clock frequency + * that the clock is currently at. + */ +struct ti_sci_msg_req_get_clock_freq { + struct ti_sci_msg_hdr hdr; + u32 dev_id; + u8 clk_id; +} __packed; + +/** + * struct ti_sci_msg_resp_get_clock_freq - Response of clock frequency request + * @hdr: Generic Header + * @freq_hz: Frequency that the clock is currently on, in Hz. + * + * Response to request type TI_SCI_MSG_GET_CLOCK_FREQ. + */ +struct ti_sci_msg_resp_get_clock_freq { + struct ti_sci_msg_hdr hdr; + u64 freq_hz; +} __packed; + +#endif /* __TI_SCI_H */ |