1 files changed, 27 insertions, 19 deletions

diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index eaaf5d70e352..9f06dec0fc61 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -569,30 +569,13 @@ static void sun4i_tcon0_mode_set_rgb(struct sun4i_tcon *tcon,
 	if (info->bus_flags & DRM_BUS_FLAG_DE_LOW)
 		val |= SUN4I_TCON0_IO_POL_DE_NEGATIVE;
 
-	/*
-	 * On A20 and similar SoCs, the only way to achieve Positive Edge
-	 * (Rising Edge), is setting dclk clock phase to 2/3(240°).
-	 * By default TCON works in Negative Edge(Falling Edge),
-	 * this is why phase is set to 0 in that case.
-	 * Unfortunately there's no way to logically invert dclk through
-	 * IO_POL register.
-	 * The only acceptable way to work, triple checked with scope,
-	 * is using clock phase set to 0° for Negative Edge and set to 240°
-	 * for Positive Edge.
-	 * On A33 and similar SoCs there would be a 90° phase option,
-	 * but it divides also dclk by 2.
-	 * Following code is a way to avoid quirks all around TCON
-	 * and DOTCLOCK drivers.
-	 */
-	if (info->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE)
-		clk_set_phase(tcon->dclk, 240);
-
 	if (info->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
-		clk_set_phase(tcon->dclk, 0);
+		val |= SUN4I_TCON0_IO_POL_DCLK_DRIVE_NEGEDGE;
 
 	regmap_update_bits(tcon->regs, SUN4I_TCON0_IO_POL_REG,
 			   SUN4I_TCON0_IO_POL_HSYNC_POSITIVE |
 			   SUN4I_TCON0_IO_POL_VSYNC_POSITIVE |
+			   SUN4I_TCON0_IO_POL_DCLK_DRIVE_NEGEDGE |
 			   SUN4I_TCON0_IO_POL_DE_NEGATIVE,
 			   val);
 
@@ -689,6 +672,30 @@ static void sun4i_tcon1_mode_set(struct sun4i_tcon *tcon,
 		     SUN4I_TCON1_BASIC5_V_SYNC(vsync) |
 		     SUN4I_TCON1_BASIC5_H_SYNC(hsync));
 
+	/* Setup the polarity of multiple signals */
+	if (tcon->quirks->polarity_in_ch0) {
+		val = 0;
+
+		if (mode->flags & DRM_MODE_FLAG_PHSYNC)
+			val |= SUN4I_TCON0_IO_POL_HSYNC_POSITIVE;
+
+		if (mode->flags & DRM_MODE_FLAG_PVSYNC)
+			val |= SUN4I_TCON0_IO_POL_VSYNC_POSITIVE;
+
+		regmap_write(tcon->regs, SUN4I_TCON0_IO_POL_REG, val);
+	} else {
+		/* according to vendor driver, this bit must be always set */
+		val = SUN4I_TCON1_IO_POL_UNKNOWN;
+
+		if (mode->flags & DRM_MODE_FLAG_PHSYNC)
+			val |= SUN4I_TCON1_IO_POL_HSYNC_POSITIVE;
+
+		if (mode->flags & DRM_MODE_FLAG_PVSYNC)
+			val |= SUN4I_TCON1_IO_POL_VSYNC_POSITIVE;
+
+		regmap_write(tcon->regs, SUN4I_TCON1_IO_POL_REG, val);
+	}
+
 	/* Map output pins to channel 1 */
 	regmap_update_bits(tcon->regs, SUN4I_TCON_GCTL_REG,
 			   SUN4I_TCON_GCTL_IOMAP_MASK,
@@ -1517,6 +1524,7 @@ static const struct sun4i_tcon_quirks sun8i_a83t_tv_quirks = {
 
 static const struct sun4i_tcon_quirks sun8i_r40_tv_quirks = {
 	.has_channel_1		= true,
+	.polarity_in_ch0	= true,
 	.set_mux		= sun8i_r40_tcon_tv_set_mux,
 };