diff options
Diffstat (limited to 'drivers/ide/cy82c693.c')
| -rw-r--r-- | drivers/ide/cy82c693.c | 106 |
1 files changed, 20 insertions, 86 deletions
diff --git a/drivers/ide/cy82c693.c b/drivers/ide/cy82c693.c index d6e2cbbc53a0..49dfb8d40dcf 100644 --- a/drivers/ide/cy82c693.c +++ b/drivers/ide/cy82c693.c @@ -1,6 +1,7 @@ /* * Copyright (C) 1998-2000 Andreas S. Krebs (akrebs@altavista.net), Maintainer * Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>, Integrator + * Copyright (C) 2007-2010 Bartlomiej Zolnierkiewicz * * CYPRESS CY82C693 chipset IDE controller * @@ -81,80 +82,6 @@ #define CY82_INDEX_CHANNEL1 0x31 #define CY82_INDEX_TIMEOUT 0x32 -/* the min and max PCI bus speed in MHz - from datasheet */ -#define CY82C963_MIN_BUS_SPEED 25 -#define CY82C963_MAX_BUS_SPEED 33 - -/* the struct for the PIO mode timings */ -typedef struct pio_clocks_s { - u8 address_time; /* Address setup (clocks) */ - u8 time_16r; /* clocks for 16bit IOR (0xF0=Active/data, 0x0F=Recovery) */ - u8 time_16w; /* clocks for 16bit IOW (0xF0=Active/data, 0x0F=Recovery) */ - u8 time_8; /* clocks for 8bit (0xF0=Active/data, 0x0F=Recovery) */ -} pio_clocks_t; - -/* - * calc clocks using bus_speed - * returns (rounded up) time in bus clocks for time in ns - */ -static int calc_clk(int time, int bus_speed) -{ - int clocks; - - clocks = (time*bus_speed+999)/1000 - 1; - - if (clocks < 0) - clocks = 0; - - if (clocks > 0x0F) - clocks = 0x0F; - - return clocks; -} - -/* - * compute the values for the clock registers for PIO - * mode and pci_clk [MHz] speed - * - * NOTE: for mode 0,1 and 2 drives 8-bit IDE command control registers are used - * for mode 3 and 4 drives 8 and 16-bit timings are the same - * - */ -static void compute_clocks(u8 pio, pio_clocks_t *p_pclk) -{ - struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio); - int clk1, clk2; - int bus_speed = ide_pci_clk ? ide_pci_clk : 33; - - /* we don't check against CY82C693's min and max speed, - * so you can play with the idebus=xx parameter - */ - - /* let's calc the address setup time clocks */ - p_pclk->address_time = (u8)calc_clk(t->setup, bus_speed); - - /* let's calc the active and recovery time clocks */ - clk1 = calc_clk(t->active, bus_speed); - - /* calc recovery timing */ - clk2 = t->cycle - t->active - t->setup; - - clk2 = calc_clk(clk2, bus_speed); - - clk1 = (clk1<<4)|clk2; /* combine active and recovery clocks */ - - /* note: we use the same values for 16bit IOR and IOW - * those are all the same, since I don't have other - * timings than those from ide-lib.c - */ - - p_pclk->time_16r = (u8)clk1; - p_pclk->time_16w = (u8)clk1; - - /* what are good values for 8bit ?? */ - p_pclk->time_8 = (u8)clk1; -} - /* * set DMA mode a specific channel for CY82C693 */ @@ -190,8 +117,11 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio) { ide_hwif_t *hwif = drive->hwif; struct pci_dev *dev = to_pci_dev(hwif->dev); - pio_clocks_t pclk; + int bus_speed = ide_pci_clk ? ide_pci_clk : 33; + const unsigned long T = 1000000 / bus_speed; unsigned int addrCtrl; + struct ide_timing t; + u8 time_16, time_8; /* select primary or secondary channel */ if (hwif->index > 0) { /* drive is on the secondary channel */ @@ -204,8 +134,12 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio) } } - /* let's calc the values for this PIO mode */ - compute_clocks(pio, &pclk); + ide_timing_compute(drive, XFER_PIO_0 + pio, &t, T, 1); + + time_16 = clamp_val(t.recover - 1, 0, 15) | + (clamp_val(t.active - 1, 0, 15) << 4); + time_8 = clamp_val(t.act8b - 1, 0, 15) | + (clamp_val(t.rec8b - 1, 0, 15) << 4); /* now let's write the clocks registers */ if ((drive->dn & 1) == 0) { @@ -217,13 +151,13 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio) pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl); addrCtrl &= (~0xF); - addrCtrl |= (unsigned int)pclk.address_time; + addrCtrl |= clamp_val(t.setup - 1, 0, 15); pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl); /* now let's set the remaining registers */ - pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r); - pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w); - pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8); + pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, time_16); + pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, time_16); + pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, time_8); } else { /* * set slave drive @@ -233,13 +167,13 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio) pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl); addrCtrl &= (~0xF0); - addrCtrl |= ((unsigned int)pclk.address_time<<4); + addrCtrl |= (clamp_val(t.setup - 1, 0, 15) << 4); pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl); /* now let's set the remaining registers */ - pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r); - pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w); - pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8); + pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, time_16); + pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, time_16); + pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, time_8); } } @@ -325,6 +259,6 @@ static void __exit cy82c693_ide_exit(void) module_init(cy82c693_ide_init); module_exit(cy82c693_ide_exit); -MODULE_AUTHOR("Andreas Krebs, Andre Hedrick"); +MODULE_AUTHOR("Andreas Krebs, Andre Hedrick, Bartlomiej Zolnierkiewicz"); MODULE_DESCRIPTION("PCI driver module for the Cypress CY82C693 IDE"); MODULE_LICENSE("GPL"); |