diff options
Diffstat (limited to 'drivers/ieee1394/Kconfig')
| -rw-r--r-- | drivers/ieee1394/Kconfig | 182 |
1 files changed, 0 insertions, 182 deletions
diff --git a/drivers/ieee1394/Kconfig b/drivers/ieee1394/Kconfig deleted file mode 100644 index e02096cf7d95..000000000000 --- a/drivers/ieee1394/Kconfig +++ /dev/null @@ -1,182 +0,0 @@ -config IEEE1394 - tristate "Legacy alternative FireWire driver stack" - depends on PCI || BROKEN - help - IEEE 1394 describes a high performance serial bus, which is also - known as FireWire(tm) or i.Link(tm) and is used for connecting all - sorts of devices (most notably digital video cameras) to your - computer. - - If you have FireWire hardware and want to use it, say Y here. This - is the core support only, you will also need to select a driver for - your IEEE 1394 adapter. - - To compile this driver as a module, say M here: the module will be - called ieee1394. - - NOTE: - ieee1394 is superseded by the newer firewire-core driver. See - http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for - further information on how to switch to the new FireWire drivers. - -config IEEE1394_OHCI1394 - tristate "OHCI-1394 controllers" - depends on PCI && IEEE1394 - help - Enable this driver if you have an IEEE 1394 controller based on the - OHCI-1394 specification. The current driver is only tested with OHCI - chipsets made by Texas Instruments and NEC. Most third-party vendors - use one of these chipsets. It should work with any OHCI-1394 - compliant card, however. - - To compile this driver as a module, say M here: the module will be - called ohci1394. - - NOTE: - ohci1394 is superseded by the newer firewire-ohci driver. See - http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for - further information on how to switch to the new FireWire drivers. - - If you want to install firewire-ohci and ohci1394 together, you - should configure them only as modules and blacklist the driver(s) - which you don't want to have auto-loaded. Add either - - blacklist ohci1394 - blacklist video1394 - blacklist dv1394 - or - blacklist firewire-ohci - - to /etc/modprobe.conf or /etc/modprobe.d/* and update modprobe.conf - depending on your distribution. - -comment "PCILynx controller requires I2C" - depends on IEEE1394 && I2C=n - -config IEEE1394_PCILYNX - tristate "PCILynx controller" - depends on PCI && IEEE1394 && I2C - select I2C_ALGOBIT - help - Say Y here if you have an IEEE-1394 controller with the Texas - Instruments PCILynx chip. Note: this driver is written for revision - 2 of this chip and may not work with revision 0. - - To compile this driver as a module, say M here: the module will be - called pcilynx. - - Only some old and now very rare PCI and CardBus cards and - PowerMacs G3 B&W contain the PCILynx controller. Therefore - almost everybody can say N here. - -comment "SBP-2 support (for storage devices) requires SCSI" - depends on IEEE1394 && SCSI=n - -config IEEE1394_SBP2 - tristate "Storage devices (SBP-2 protocol)" - depends on IEEE1394 && SCSI - help - This option enables you to use SBP-2 devices connected to an IEEE - 1394 bus. SBP-2 devices include storage devices like harddisks and - DVD drives, also some other FireWire devices like scanners. - - You should also enable support for disks, CD-ROMs, etc. in the SCSI - configuration section. - - To compile this driver as a module, say M here: the module will be - called sbp2. - - NOTE: - sbp2 is superseded by the newer firewire-sbp2 driver. See - http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for - further information on how to switch to the new FireWire drivers. - -config IEEE1394_SBP2_PHYS_DMA - bool "Enable replacement for physical DMA in SBP2" - depends on IEEE1394_SBP2 && VIRT_TO_BUS && EXPERIMENTAL - help - This builds sbp2 for use with non-OHCI host adapters which do not - support physical DMA or for when ohci1394 is run with phys_dma=0. - Physical DMA is data movement without assistance of the drivers' - interrupt handlers. This option includes the interrupt handlers - that are required in absence of this hardware feature. - - This option is buggy and currently broken on some architectures. - If unsure, say N. - -config IEEE1394_ETH1394_ROM_ENTRY - depends on IEEE1394 - bool - default n - -config IEEE1394_ETH1394 - tristate "IP networking over 1394 (experimental)" - depends on IEEE1394 && EXPERIMENTAL && INET - select IEEE1394_ETH1394_ROM_ENTRY - help - This driver implements a functional majority of RFC 2734: IPv4 over - 1394. It will provide IP connectivity with implementations of RFC - 2734 found on other operating systems. It will not communicate with - older versions of this driver found in stock kernels prior to 2.6.3. - This driver is still considered experimental. It does not yet support - MCAP, therefore multicast support is significantly limited. - - The module is called eth1394 although it does not emulate Ethernet. - - NOTE: - eth1394 is superseded by the newer firewire-net driver. See - http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for - further information on how to switch to the new FireWire drivers. - -config IEEE1394_RAWIO - tristate "raw1394 userspace interface" - depends on IEEE1394 - help - This option adds support for the raw1394 device file which enables - direct communication of user programs with IEEE 1394 devices - (isochronous and asynchronous). Almost all application programs - which access FireWire require this option. - - To compile this driver as a module, say M here: the module will be - called raw1394. - - NOTE: - raw1394 is superseded by the newer firewire-core driver. See - http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for - further information on how to switch to the new FireWire drivers. - -config IEEE1394_VIDEO1394 - tristate "video1394 userspace interface" - depends on IEEE1394 && IEEE1394_OHCI1394 - help - This option adds support for the video1394 device files which enable - isochronous communication of user programs with IEEE 1394 devices, - especially video capture or export. This interface is used by all - libdc1394 based programs and by several other programs, in addition to - the raw1394 interface. It is generally not required for DV capture. - - To compile this driver as a module, say M here: the module will be - called video1394. - - NOTE: - video1394 is superseded by the newer firewire-core driver. See - http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for - further information on how to switch to the new FireWire drivers. - -config IEEE1394_DV1394 - tristate "dv1394 userspace interface (deprecated)" - depends on IEEE1394 && IEEE1394_OHCI1394 - help - The dv1394 driver is unsupported and may be removed from Linux in a - future release. Its functionality is now provided by either - raw1394 or firewire-core together with libraries such as libiec61883. - -config IEEE1394_VERBOSEDEBUG - bool "Excessive debugging output" - depends on IEEE1394 - help - If you say Y here, you will get very verbose debugging logs from the - ieee1394 drivers, including sent and received packet headers. This - will quickly result in large amounts of data sent to the system log. - - Say Y if you really need the debugging output. Everyone else says N. |