diff options
Diffstat (limited to 'drivers/infiniband/hw/mthca/mthca_main.c')
| -rw-r--r-- | drivers/infiniband/hw/mthca/mthca_main.c | 28 |
1 files changed, 28 insertions, 0 deletions
diff --git a/drivers/infiniband/hw/mthca/mthca_main.c b/drivers/infiniband/hw/mthca/mthca_main.c index 266f347c6707..9b9ff7bff357 100644 --- a/drivers/infiniband/hw/mthca/mthca_main.c +++ b/drivers/infiniband/hw/mthca/mthca_main.c @@ -52,6 +52,14 @@ MODULE_DESCRIPTION("Mellanox InfiniBand HCA low-level driver"); MODULE_LICENSE("Dual BSD/GPL"); MODULE_VERSION(DRV_VERSION); +#ifdef CONFIG_INFINIBAND_MTHCA_DEBUG + +int mthca_debug_level = 0; +module_param_named(debug_level, mthca_debug_level, int, 0644); +MODULE_PARM_DESC(debug_level, "Enable debug tracing if > 0"); + +#endif /* CONFIG_INFINIBAND_MTHCA_DEBUG */ + #ifdef CONFIG_PCI_MSI static int msi_x = 0; @@ -69,6 +77,10 @@ MODULE_PARM_DESC(msi, "attempt to use MSI if nonzero"); #endif /* CONFIG_PCI_MSI */ +static int tune_pci = 0; +module_param(tune_pci, int, 0444); +MODULE_PARM_DESC(tune_pci, "increase PCI burst from the default set by BIOS if nonzero"); + static const char mthca_version[] __devinitdata = DRV_NAME ": Mellanox InfiniBand HCA driver v" DRV_VERSION " (" DRV_RELDATE ")\n"; @@ -90,6 +102,9 @@ static int __devinit mthca_tune_pci(struct mthca_dev *mdev) int cap; u16 val; + if (!tune_pci) + return 0; + /* First try to max out Read Byte Count */ cap = pci_find_capability(mdev->pdev, PCI_CAP_ID_PCIX); if (cap) { @@ -176,6 +191,7 @@ static int __devinit mthca_dev_lim(struct mthca_dev *mdev, struct mthca_dev_lim mdev->limits.reserved_srqs = dev_lim->reserved_srqs; mdev->limits.reserved_eecs = dev_lim->reserved_eecs; mdev->limits.max_desc_sz = dev_lim->max_desc_sz; + mdev->limits.max_srq_sge = mthca_max_srq_sge(mdev); /* * Subtract 1 from the limit because we need to allocate a * spare CQE so the HCA HW can tell the difference between an @@ -191,6 +207,18 @@ static int __devinit mthca_dev_lim(struct mthca_dev *mdev, struct mthca_dev_lim mdev->limits.port_width_cap = dev_lim->max_port_width; mdev->limits.page_size_cap = ~(u32) (dev_lim->min_page_sz - 1); mdev->limits.flags = dev_lim->flags; + /* + * For old FW that doesn't return static rate support, use a + * value of 0x3 (only static rate values of 0 or 1 are handled), + * except on Sinai, where even old FW can handle static rate + * values of 2 and 3. + */ + if (dev_lim->stat_rate_support) + mdev->limits.stat_rate_support = dev_lim->stat_rate_support; + else if (mdev->mthca_flags & MTHCA_FLAG_SINAI_OPT) + mdev->limits.stat_rate_support = 0xf; + else + mdev->limits.stat_rate_support = 0x3; /* IB_DEVICE_RESIZE_MAX_WR not supported by driver. May be doable since hardware supports it for SRQ. |