diff options
Diffstat (limited to 'drivers/lguest/segments.c')
| -rw-r--r-- | drivers/lguest/segments.c | 177 |
1 files changed, 177 insertions, 0 deletions
diff --git a/drivers/lguest/segments.c b/drivers/lguest/segments.c new file mode 100644 index 000000000000..9b81119f46e9 --- /dev/null +++ b/drivers/lguest/segments.c @@ -0,0 +1,177 @@ +/*P:600 The x86 architecture has segments, which involve a table of descriptors + * which can be used to do funky things with virtual address interpretation. + * We originally used to use segments so the Guest couldn't alter the + * Guest<->Host Switcher, and then we had to trim Guest segments, and restore + * for userspace per-thread segments, but trim again for on userspace->kernel + * transitions... This nightmarish creation was contained within this file, + * where we knew not to tread without heavy armament and a change of underwear. + * + * In these modern times, the segment handling code consists of simple sanity + * checks, and the worst you'll experience reading this code is butterfly-rash + * from frolicking through its parklike serenity. :*/ +#include "lg.h" + +/*H:600 + * We've almost completed the Host; there's just one file to go! + * + * Segments & The Global Descriptor Table + * + * (That title sounds like a bad Nerdcore group. Not to suggest that there are + * any good Nerdcore groups, but in high school a friend of mine had a band + * called Joe Fish and the Chips, so there are definitely worse band names). + * + * To refresh: the GDT is a table of 8-byte values describing segments. Once + * set up, these segments can be loaded into one of the 6 "segment registers". + * + * GDT entries are passed around as "struct desc_struct"s, which like IDT + * entries are split into two 32-bit members, "a" and "b". One day, someone + * will clean that up, and be declared a Hero. (No pressure, I'm just saying). + * + * Anyway, the GDT entry contains a base (the start address of the segment), a + * limit (the size of the segment - 1), and some flags. Sounds simple, and it + * would be, except those zany Intel engineers decided that it was too boring + * to put the base at one end, the limit at the other, and the flags in + * between. They decided to shotgun the bits at random throughout the 8 bytes, + * like so: + * + * 0 16 40 48 52 56 63 + * [ limit part 1 ][ base part 1 ][ flags ][li][fl][base ] + * mit ags part 2 + * part 2 + * + * As a result, this file contains a certain amount of magic numeracy. Let's + * begin. + */ + +/* There are several entries we don't let the Guest set. The TSS entry is the + * "Task State Segment" which controls all kinds of delicate things. The + * LGUEST_CS and LGUEST_DS entries are reserved for the Switcher, and the + * the Guest can't be trusted to deal with double faults. */ +static int ignored_gdt(unsigned int num) +{ + return (num == GDT_ENTRY_TSS + || num == GDT_ENTRY_LGUEST_CS + || num == GDT_ENTRY_LGUEST_DS + || num == GDT_ENTRY_DOUBLEFAULT_TSS); +} + +/*H:610 Once the GDT has been changed, we fix the new entries up a little. We + * don't care if they're invalid: the worst that can happen is a General + * Protection Fault in the Switcher when it restores a Guest segment register + * which tries to use that entry. Then we kill the Guest for causing such a + * mess: the message will be "unhandled trap 256". */ +static void fixup_gdt_table(struct lguest *lg, unsigned start, unsigned end) +{ + unsigned int i; + + for (i = start; i < end; i++) { + /* We never copy these ones to real GDT, so we don't care what + * they say */ + if (ignored_gdt(i)) + continue; + + /* Segment descriptors contain a privilege level: the Guest is + * sometimes careless and leaves this as 0, even though it's + * running at privilege level 1. If so, we fix it here. */ + if ((lg->gdt[i].b & 0x00006000) == 0) + lg->gdt[i].b |= (GUEST_PL << 13); + + /* Each descriptor has an "accessed" bit. If we don't set it + * now, the CPU will try to set it when the Guest first loads + * that entry into a segment register. But the GDT isn't + * writable by the Guest, so bad things can happen. */ + lg->gdt[i].b |= 0x00000100; + } +} + +/* This routine is called at boot or modprobe time for each CPU to set up the + * "constant" GDT entries for Guests running on that CPU. */ +void setup_default_gdt_entries(struct lguest_ro_state *state) +{ + struct desc_struct *gdt = state->guest_gdt; + unsigned long tss = (unsigned long)&state->guest_tss; + + /* The hypervisor segments are full 0-4G segments, privilege level 0 */ + gdt[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT; + gdt[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT; + + /* The TSS segment refers to the TSS entry for this CPU, so we cannot + * copy it from the Guest. Forgive the magic flags */ + gdt[GDT_ENTRY_TSS].a = 0x00000067 | (tss << 16); + gdt[GDT_ENTRY_TSS].b = 0x00008900 | (tss & 0xFF000000) + | ((tss >> 16) & 0x000000FF); +} + +/* This routine is called before the Guest is run for the first time. */ +void setup_guest_gdt(struct lguest *lg) +{ + /* Start with full 0-4G segments... */ + lg->gdt[GDT_ENTRY_KERNEL_CS] = FULL_EXEC_SEGMENT; + lg->gdt[GDT_ENTRY_KERNEL_DS] = FULL_SEGMENT; + /* ...except the Guest is allowed to use them, so set the privilege + * level appropriately in the flags. */ + lg->gdt[GDT_ENTRY_KERNEL_CS].b |= (GUEST_PL << 13); + lg->gdt[GDT_ENTRY_KERNEL_DS].b |= (GUEST_PL << 13); +} + +/* Like the IDT, we never simply use the GDT the Guest gives us. We set up the + * GDTs for each CPU, then we copy across the entries each time we want to run + * a different Guest on that CPU. */ + +/* A partial GDT load, for the three "thead-local storage" entries. Otherwise + * it's just like load_guest_gdt(). So much, in fact, it would probably be + * neater to have a single hypercall to cover both. */ +void copy_gdt_tls(const struct lguest *lg, struct desc_struct *gdt) +{ + unsigned int i; + + for (i = GDT_ENTRY_TLS_MIN; i <= GDT_ENTRY_TLS_MAX; i++) + gdt[i] = lg->gdt[i]; +} + +/* This is the full version */ +void copy_gdt(const struct lguest *lg, struct desc_struct *gdt) +{ + unsigned int i; + + /* The default entries from setup_default_gdt_entries() are not + * replaced. See ignored_gdt() above. */ + for (i = 0; i < GDT_ENTRIES; i++) + if (!ignored_gdt(i)) + gdt[i] = lg->gdt[i]; +} + +/* This is where the Guest asks us to load a new GDT (LHCALL_LOAD_GDT). */ +void load_guest_gdt(struct lguest *lg, unsigned long table, u32 num) +{ + /* We assume the Guest has the same number of GDT entries as the + * Host, otherwise we'd have to dynamically allocate the Guest GDT. */ + if (num > ARRAY_SIZE(lg->gdt)) + kill_guest(lg, "too many gdt entries %i", num); + + /* We read the whole thing in, then fix it up. */ + lgread(lg, lg->gdt, table, num * sizeof(lg->gdt[0])); + fixup_gdt_table(lg, 0, ARRAY_SIZE(lg->gdt)); + /* Mark that the GDT changed so the core knows it has to copy it again, + * even if the Guest is run on the same CPU. */ + lg->changed |= CHANGED_GDT; +} + +void guest_load_tls(struct lguest *lg, unsigned long gtls) +{ + struct desc_struct *tls = &lg->gdt[GDT_ENTRY_TLS_MIN]; + + lgread(lg, tls, gtls, sizeof(*tls)*GDT_ENTRY_TLS_ENTRIES); + fixup_gdt_table(lg, GDT_ENTRY_TLS_MIN, GDT_ENTRY_TLS_MAX+1); + lg->changed |= CHANGED_GDT_TLS; +} + +/* + * With this, we have finished the Host. + * + * Five of the seven parts of our task are complete. You have made it through + * the Bit of Despair (I think that's somewhere in the page table code, + * myself). + * + * Next, we examine "make Switcher". It's short, but intense. + */ |