diff options
Diffstat (limited to 'drivers/media/IR/ene_ir.h')
| -rw-r--r-- | drivers/media/IR/ene_ir.h | 273 |
1 files changed, 150 insertions, 123 deletions
diff --git a/drivers/media/IR/ene_ir.h b/drivers/media/IR/ene_ir.h index 54c76af0d033..39c707b42412 100644 --- a/drivers/media/IR/ene_ir.h +++ b/drivers/media/IR/ene_ir.h @@ -1,5 +1,5 @@ /* - * driver for ENE KB3926 B/C/D CIR (also known as ENE0XXX) + * driver for ENE KB3926 B/C/D/E/F CIR (also known as ENE0XXX) * * Copyright (C) 2010 Maxim Levitsky <maximlevitsky@gmail.com> * @@ -26,43 +26,50 @@ #define ENE_ADDR_HI 1 /* hi byte of register address */ #define ENE_ADDR_LO 2 /* low byte of register address */ #define ENE_IO 3 /* read/write window */ -#define ENE_MAX_IO 4 - -/* 8 bytes of samples, divided in 2 halfs*/ -#define ENE_SAMPLE_BUFFER 0xF8F0 /* regular sample buffer */ -#define ENE_SAMPLE_SPC_MASK 0x80 /* sample is space */ -#define ENE_SAMPLE_VALUE_MASK 0x7F -#define ENE_SAMPLE_OVERFLOW 0x7F -#define ENE_SAMPLES_SIZE 4 - -/* fan input sample buffer */ -#define ENE_SAMPLE_BUFFER_FAN 0xF8FB /* this buffer holds high byte of */ - /* each sample of normal buffer */ -#define ENE_FAN_SMPL_PULS_MSK 0x8000 /* this bit of combined sample */ - /* if set, says that sample is pulse */ -#define ENE_FAN_VALUE_MASK 0x0FFF /* mask for valid bits of the value */ - -/* first firmware register */ -#define ENE_FW1 0xF8F8 +#define ENE_IO_SIZE 4 + +/* 8 bytes of samples, divided in 2 packets*/ +#define ENE_FW_SAMPLE_BUFFER 0xF8F0 /* sample buffer */ +#define ENE_FW_SAMPLE_SPACE 0x80 /* sample is space */ +#define ENE_FW_PACKET_SIZE 4 + +/* first firmware flag register */ +#define ENE_FW1 0xF8F8 /* flagr */ #define ENE_FW1_ENABLE 0x01 /* enable fw processing */ #define ENE_FW1_TXIRQ 0x02 /* TX interrupt pending */ +#define ENE_FW1_HAS_EXTRA_BUF 0x04 /* fw uses extra buffer*/ +#define ENE_FW1_EXTRA_BUF_HND 0x08 /* extra buffer handshake bit*/ +#define ENE_FW1_LED_ON 0x10 /* turn on a led */ + +#define ENE_FW1_WPATTERN 0x20 /* enable wake pattern */ #define ENE_FW1_WAKE 0x40 /* enable wake from S3 */ #define ENE_FW1_IRQ 0x80 /* enable interrupt */ -/* second firmware register */ -#define ENE_FW2 0xF8F9 -#define ENE_FW2_BUF_HIGH 0x01 /* which half of the buffer to read */ -#define ENE_FW2_IRQ_CLR 0x04 /* clear this on IRQ */ -#define ENE_FW2_GP40_AS_LEARN 0x08 /* normal input is used as */ - /* learning input */ -#define ENE_FW2_FAN_AS_NRML_IN 0x40 /* fan is used as normal input */ +/* second firmware flag register */ +#define ENE_FW2 0xF8F9 /* flagw */ +#define ENE_FW2_BUF_WPTR 0x01 /* which half of the buffer to read */ +#define ENE_FW2_RXIRQ 0x04 /* RX IRQ pending*/ +#define ENE_FW2_GP0A 0x08 /* Use GPIO0A for demodulated input */ +#define ENE_FW2_EMMITER1_CONN 0x10 /* TX emmiter 1 connected */ +#define ENE_FW2_EMMITER2_CONN 0x20 /* TX emmiter 2 connected */ + +#define ENE_FW2_FAN_INPUT 0x40 /* fan input used for demodulated data*/ #define ENE_FW2_LEARNING 0x80 /* hardware supports learning and TX */ +/* firmware RX pointer for new style buffer */ +#define ENE_FW_RX_POINTER 0xF8FA + +/* high parts of samples for fan input (8 samples)*/ +#define ENE_FW_SMPL_BUF_FAN 0xF8FB +#define ENE_FW_SMPL_BUF_FAN_PLS 0x8000 /* combined sample is pulse */ +#define ENE_FW_SMPL_BUF_FAN_MSK 0x0FFF /* combined sample maximum value */ +#define ENE_FW_SAMPLE_PERIOD_FAN 61 /* fan input has fixed sample period */ + /* transmitter ports */ -#define ENE_TX_PORT2 0xFC01 /* this enables one or both */ -#define ENE_TX_PORT2_EN 0x20 /* TX ports */ -#define ENE_TX_PORT1 0xFC08 -#define ENE_TX_PORT1_EN 0x02 +#define ENE_GPIOFS1 0xFC01 +#define ENE_GPIOFS1_GPIO0D 0x20 /* enable tx output on GPIO0D */ +#define ENE_GPIOFS8 0xFC08 +#define ENE_GPIOFS8_GPIO41 0x02 /* enable tx output on GPIO40 */ /* IRQ registers block (for revision B) */ #define ENEB_IRQ 0xFD09 /* IRQ number */ @@ -70,97 +77,99 @@ #define ENEB_IRQ_STATUS 0xFD80 /* irq status */ #define ENEB_IRQ_STATUS_IR 0x20 /* IR irq */ -/* fan as input settings - only if learning capable */ +/* fan as input settings */ #define ENE_FAN_AS_IN1 0xFE30 /* fan init reg 1 */ #define ENE_FAN_AS_IN1_EN 0xCD #define ENE_FAN_AS_IN2 0xFE31 /* fan init reg 2 */ #define ENE_FAN_AS_IN2_EN 0x03 -#define ENE_SAMPLE_PERIOD_FAN 61 /* fan input has fixed sample period */ /* IRQ registers block (for revision C,D) */ -#define ENEC_IRQ 0xFE9B /* new irq settings register */ -#define ENEC_IRQ_MASK 0x0F /* irq number mask */ -#define ENEC_IRQ_UNK_EN 0x10 /* always enabled */ -#define ENEC_IRQ_STATUS 0x20 /* irq status and ACK */ - -/* CIR block settings */ -#define ENE_CIR_CONF1 0xFEC0 -#define ENE_CIR_CONF1_TX_CLEAR 0x01 /* clear that on revC */ - /* while transmitting */ -#define ENE_CIR_CONF1_RX_ON 0x07 /* normal receiver enabled */ -#define ENE_CIR_CONF1_LEARN1 0x08 /* enabled on learning mode */ -#define ENE_CIR_CONF1_TX_ON 0x30 /* enabled on transmit */ -#define ENE_CIR_CONF1_TX_CARR 0x80 /* send TX carrier or not */ - -#define ENE_CIR_CONF2 0xFEC1 /* unknown setting = 0 */ -#define ENE_CIR_CONF2_LEARN2 0x10 /* set on enable learning */ -#define ENE_CIR_CONF2_GPIO40DIS 0x20 /* disable input via gpio40 */ - -#define ENE_CIR_SAMPLE_PERIOD 0xFEC8 /* sample period in us */ -#define ENE_CIR_SAMPLE_OVERFLOW 0x80 /* interrupt on overflows if set */ - - -/* Two byte tx buffer */ -#define ENE_TX_INPUT1 0xFEC9 -#define ENE_TX_INPUT2 0xFECA -#define ENE_TX_PULSE_MASK 0x80 /* Transmitted sample is pulse */ -#define ENE_TX_SMLP_MASK 0x7F -#define ENE_TX_SMPL_PERIOD 50 /* transmit sample period - fixed */ +#define ENE_IRQ 0xFE9B /* new irq settings register */ +#define ENE_IRQ_MASK 0x0F /* irq number mask */ +#define ENE_IRQ_UNK_EN 0x10 /* always enabled */ +#define ENE_IRQ_STATUS 0x20 /* irq status and ACK */ + +/* CIR Config register #1 */ +#define ENE_CIRCFG 0xFEC0 +#define ENE_CIRCFG_RX_EN 0x01 /* RX enable */ +#define ENE_CIRCFG_RX_IRQ 0x02 /* Enable hardware interrupt */ +#define ENE_CIRCFG_REV_POL 0x04 /* Input polarity reversed */ +#define ENE_CIRCFG_CARR_DEMOD 0x08 /* Enable carrier demodulator */ + +#define ENE_CIRCFG_TX_EN 0x10 /* TX enable */ +#define ENE_CIRCFG_TX_IRQ 0x20 /* Send interrupt on TX done */ +#define ENE_CIRCFG_TX_POL_REV 0x40 /* TX polarity reversed */ +#define ENE_CIRCFG_TX_CARR 0x80 /* send TX carrier or not */ + +/* CIR config register #2 */ +#define ENE_CIRCFG2 0xFEC1 +#define ENE_CIRCFG2_RLC 0x00 +#define ENE_CIRCFG2_RC5 0x01 +#define ENE_CIRCFG2_RC6 0x02 +#define ENE_CIRCFG2_NEC 0x03 +#define ENE_CIRCFG2_CARR_DETECT 0x10 /* Enable carrier detection */ +#define ENE_CIRCFG2_GPIO0A 0x20 /* Use GPIO0A instead of GPIO40 for input */ +#define ENE_CIRCFG2_FAST_SAMPL1 0x40 /* Fast leading pulse detection for RC6 */ +#define ENE_CIRCFG2_FAST_SAMPL2 0x80 /* Fast data detection for RC6 */ + +/* Knobs for protocol decoding - will document when/if will use them */ +#define ENE_CIRPF 0xFEC2 +#define ENE_CIRHIGH 0xFEC3 +#define ENE_CIRBIT 0xFEC4 +#define ENE_CIRSTART 0xFEC5 +#define ENE_CIRSTART2 0xFEC6 + +/* Actual register which contains RLC RX data - read by firmware */ +#define ENE_CIRDAT_IN 0xFEC7 + + +/* RLC configuration - sample period (1us resulution) + idle mode */ +#define ENE_CIRRLC_CFG 0xFEC8 +#define ENE_CIRRLC_CFG_OVERFLOW 0x80 /* interrupt on overflows if set */ +#define ENE_DEFAULT_SAMPLE_PERIOD 50 + +/* Two byte RLC TX buffer */ +#define ENE_CIRRLC_OUT0 0xFEC9 +#define ENE_CIRRLC_OUT1 0xFECA +#define ENE_CIRRLC_OUT_PULSE 0x80 /* Transmitted sample is pulse */ +#define ENE_CIRRLC_OUT_MASK 0x7F + + +/* Carrier detect setting + * Low nibble - number of carrier pulses to average + * High nibble - number of initial carrier pulses to discard + */ +#define ENE_CIRCAR_PULS 0xFECB +/* detected RX carrier period (resolution: 500 ns) */ +#define ENE_CIRCAR_PRD 0xFECC +#define ENE_CIRCAR_PRD_VALID 0x80 /* data valid content valid */ -/* Unknown TX setting - TX sample period ??? */ -#define ENE_TX_UNK1 0xFECB /* set to 0x63 */ +/* detected RX carrier pulse width (resolution: 500 ns) */ +#define ENE_CIRCAR_HPRD 0xFECD -/* Current received carrier period */ -#define ENE_RX_CARRIER 0xFECC /* RX period (500 ns) */ -#define ENE_RX_CARRIER_VALID 0x80 /* Register content valid */ +/* TX period (resolution: 500 ns, minimum 2)*/ +#define ENE_CIRMOD_PRD 0xFECE +#define ENE_CIRMOD_PRD_POL 0x80 /* TX carrier polarity*/ +#define ENE_CIRMOD_PRD_MAX 0x7F /* 15.87 kHz */ +#define ENE_CIRMOD_PRD_MIN 0x02 /* 1 Mhz */ -/* TX period (1/carrier) */ -#define ENE_TX_PERIOD 0xFECE /* TX period (500 ns) */ -#define ENE_TX_PERIOD_UNKBIT 0x80 /* This bit set on transmit*/ -#define ENE_TX_PERIOD_PULSE 0xFECF /* TX pulse period (500 ns)*/ +/* TX pulse width (resolution: 500 ns)*/ +#define ENE_CIRMOD_HPRD 0xFECF /* Hardware versions */ -#define ENE_HW_VERSION 0xFF00 /* hardware revision */ +#define ENE_ECHV 0xFF00 /* hardware revision */ #define ENE_PLLFRH 0xFF16 #define ENE_PLLFRL 0xFF17 +#define ENE_DEFAULT_PLL_FREQ 1000 -#define ENE_HW_UNK 0xFF1D -#define ENE_HW_UNK_CLR 0x04 -#define ENE_HW_VER_MAJOR 0xFF1E /* chip version */ -#define ENE_HW_VER_MINOR 0xFF1F -#define ENE_HW_VER_OLD 0xFD00 - -/* Normal/Learning carrier ranges - only valid if we have learning input*/ -/* TODO: test */ -#define ENE_NORMAL_RX_LOW 34 -#define ENE_NORMAL_RX_HI 38 +#define ENE_ECSTS 0xFF1D +#define ENE_ECSTS_RSRVD 0x04 -/* Tx carrier range */ -/* Hardware might be able to do more, but this range is enough for - all purposes */ -#define ENE_TX_PERIOD_MAX 32 /* corresponds to 29.4 kHz */ -#define ENE_TX_PERIOD_MIN 16 /* corrsponds to 62.5 kHz */ - - - -/* Minimal and maximal gaps */ - -/* Normal case: - Minimal gap is 0x7F * sample period - Maximum gap depends on hardware. - For KB3926B, it is unlimited, for newer models its around - 250000, after which HW stops sending samples, and that is - not possible to change */ - -/* Fan case: - Both minimal and maximal gaps are same, and equal to 0xFFF * 0x61 - And there is nothing to change this setting -*/ - -#define ENE_MAXGAP 250000 -#define ENE_MINGAP (127 * sample_period) +#define ENE_ECVER_MAJOR 0xFF1E /* chip version */ +#define ENE_ECVER_MINOR 0xFF1F +#define ENE_HW_VER_OLD 0xFD00 /******************************************************************************/ @@ -171,46 +180,60 @@ #define ENE_HW_B 1 /* 3926B */ #define ENE_HW_C 2 /* 3926C */ -#define ENE_HW_D 3 /* 3926D */ +#define ENE_HW_D 3 /* 3926D or later */ #define ene_printk(level, text, ...) \ - printk(level ENE_DRIVER_NAME ": " text, ## __VA_ARGS__) + printk(level ENE_DRIVER_NAME ": " text "\n", ## __VA_ARGS__) -#define ene_dbg(text, ...) \ - if (debug) \ - printk(KERN_DEBUG \ - ENE_DRIVER_NAME ": " text "\n" , ## __VA_ARGS__) +#define ene_notice(text, ...) ene_printk(KERN_NOTICE, text, ## __VA_ARGS__) +#define ene_warn(text, ...) ene_printk(KERN_WARNING, text, ## __VA_ARGS__) -#define ene_dbg_verbose(text, ...) \ - if (debug > 1) \ - printk(KERN_DEBUG \ - ENE_DRIVER_NAME ": " text "\n" , ## __VA_ARGS__) +#define __dbg(level, format, ...) \ + do { \ + if (debug >= level) \ + printk(KERN_DEBUG ENE_DRIVER_NAME \ + ": " format "\n", ## __VA_ARGS__); \ + } while (0) + + +#define dbg(format, ...) __dbg(1, format, ## __VA_ARGS__) +#define dbg_verbose(format, ...) __dbg(2, format, ## __VA_ARGS__) +#define dbg_regs(format, ...) __dbg(3, format, ## __VA_ARGS__) + +#define MS_TO_NS(msec) ((msec) * 1000) struct ene_device { struct pnp_dev *pnp_dev; struct input_dev *idev; struct ir_dev_props *props; - int in_use; /* hw IO settings */ - unsigned long hw_io; + long hw_io; int irq; spinlock_t hw_lock; /* HW features */ int hw_revision; /* hardware revision */ - bool hw_learning_and_tx_capable; /* learning capable */ - bool hw_gpio40_learning; /* gpio40 is learning */ - bool hw_fan_as_normal_input; /* fan input is used as */ - /* regular input */ + bool hw_use_gpio_0a; /* gpio40 is demodulated input*/ + bool hw_extra_buffer; /* hardware has 'extra buffer' */ + bool hw_fan_input; /* fan input is IR data source */ + bool hw_learning_and_tx_capable; /* learning & tx capable */ + int pll_freq; + int buffer_len; + + /* Extra RX buffer location */ + int extra_buf1_address; + int extra_buf1_len; + int extra_buf2_address; + int extra_buf2_len; + /* HW state*/ - int rx_pointer; /* hw pointer to rx buffer */ + int r_pointer; /* pointer to next sample to read */ + int w_pointer; /* pointer to next sample hw will write */ bool rx_fan_input_inuse; /* is fan input in use for rx*/ int tx_reg; /* current reg used for TX */ u8 saved_conf1; /* saved FEC0 reg */ - - /* TX sample handling */ unsigned int tx_sample; /* current sample for TX */ bool tx_sample_pulse; /* current sample is pulse */ @@ -232,4 +255,8 @@ struct ene_device { bool learning_enabled; /* learning input enabled */ bool carrier_detect_enabled; /* carrier detect enabled */ int rx_period_adjust; + bool rx_enabled; }; + +static int ene_irq_status(struct ene_device *dev); +static void ene_read_hw_pointer(struct ene_device *dev); |