diff options
Diffstat (limited to 'drivers/media/video/cx18/cx18-driver.h')
| -rw-r--r-- | drivers/media/video/cx18/cx18-driver.h | 72 |
1 files changed, 24 insertions, 48 deletions
diff --git a/drivers/media/video/cx18/cx18-driver.h b/drivers/media/video/cx18/cx18-driver.h index 4801bc7fb5b2..a4b1708fafe7 100644 --- a/drivers/media/video/cx18/cx18-driver.h +++ b/drivers/media/video/cx18/cx18-driver.h @@ -38,10 +38,10 @@ #include <linux/i2c-algo-bit.h> #include <linux/list.h> #include <linux/unistd.h> -#include <linux/byteorder/swab.h> #include <linux/pagemap.h> #include <linux/workqueue.h> #include <linux/mutex.h> +#include <asm/byteorder.h> #include <linux/dvb/video.h> #include <linux/dvb/audio.h> @@ -64,6 +64,9 @@ # error "This driver requires kernel PCI support." #endif +/* Default delay to throttle mmio access to the CX23418 */ +#define CX18_DEFAULT_MMIO_NDELAY 0 /* 0 ns = 0 PCI clock(s) / 33 MHz */ + #define CX18_MEM_OFFSET 0x00000000 #define CX18_MEM_SIZE 0x04000000 #define CX18_REG_OFFSET 0x02000000 @@ -77,7 +80,9 @@ #define CX18_CARD_COMPRO_H900 2 /* Compro VideoMate H900 */ #define CX18_CARD_YUAN_MPC718 3 /* Yuan MPC718 */ #define CX18_CARD_CNXT_RAPTOR_PAL 4 /* Conexant Raptor PAL */ -#define CX18_CARD_LAST 4 +#define CX18_CARD_TOSHIBA_QOSMIO_DVBT 5 /* Toshiba Qosmio Interal DVB-T/Analog*/ +#define CX18_CARD_LEADTEK_PVR2100 6 /* Leadtek WinFast PVR2100 */ +#define CX18_CARD_LAST 6 #define CX18_ENC_STREAM_TYPE_MPG 0 #define CX18_ENC_STREAM_TYPE_TS 1 @@ -97,6 +102,8 @@ #define CX18_PCI_ID_COMPRO 0x185b #define CX18_PCI_ID_YUAN 0x12ab #define CX18_PCI_ID_CONEXANT 0x14f1 +#define CX18_PCI_ID_TOSHIBA 0x1179 +#define CX18_PCI_ID_LEADTEK 0x107D /* ======================================================================== */ /* ========================== START USER SETTABLE DMA VARIABLES =========== */ @@ -169,6 +176,7 @@ #define CX18_MAX_PGM_INDEX (400) +extern int cx18_retry_mmio; /* enable check & retry of mmio accesses */ extern int cx18_debug; @@ -177,6 +185,7 @@ struct cx18_options { int cardtype; /* force card type on load */ int tuner; /* set tuner on load */ int radio; /* enable/disable radio */ + unsigned long mmio_ndelay; /* delay in ns after every PCI mmio access */ }; /* per-buffer bit flags */ @@ -216,8 +225,7 @@ struct cx18_buffer { struct cx18_queue { struct list_head list; - u32 buffers; - u32 length; + atomic_t buffers; u32 bytesused; }; @@ -237,6 +245,8 @@ struct cx18_dvb { struct cx18; /* forward reference */ struct cx18_scb; /* forward reference */ +#define CX18_INVALID_TASK_HANDLE 0xffffffff + struct cx18_stream { /* These first four fields are always set, even if the stream is not actually created. */ @@ -259,7 +269,6 @@ struct cx18_stream { /* Buffer Stats */ u32 buffers; u32 buf_size; - u32 buffers_stolen; /* Buffer Queues */ struct cx18_queue q_free; /* free buffers */ @@ -341,6 +350,13 @@ struct cx18_i2c_algo_callback_data { int bus_index; /* 0 or 1 for the cx23418's 1st or 2nd I2C bus */ }; +#define CX18_MAX_MMIO_RETRIES 10 + +struct cx18_mmio_stats { + atomic_t retried_write[CX18_MAX_MMIO_RETRIES+1]; + atomic_t retried_read[CX18_MAX_MMIO_RETRIES+1]; +}; + /* Struct to hold info about cx18 cards */ struct cx18 { int num; /* board number, -1 during init! */ @@ -430,6 +446,9 @@ struct cx18 { u32 gpio_val; struct mutex gpio_lock; + /* Statistics */ + struct cx18_mmio_stats mmio_stats; + /* v4l2 and User settings */ /* codec settings */ @@ -458,47 +477,4 @@ void cx18_read_eeprom(struct cx18 *cx, struct tveeprom *tv); /* First-open initialization: load firmware, etc. */ int cx18_init_on_first_open(struct cx18 *cx); -/* This is a PCI post thing, where if the pci register is not read, then - the write doesn't always take effect right away. By reading back the - register any pending PCI writes will be performed (in order), and so - you can be sure that the writes are guaranteed to be done. - - Rarely needed, only in some timing sensitive cases. - Apparently if this is not done some motherboards seem - to kill the firmware and get into the broken state until computer is - rebooted. */ -#define write_sync(val, reg) \ - do { writel(val, reg); readl(reg); } while (0) - -#define read_reg(reg) readl(cx->reg_mem + (reg)) -#define write_reg(val, reg) writel(val, cx->reg_mem + (reg)) -#define write_reg_sync(val, reg) \ - do { write_reg(val, reg); read_reg(reg); } while (0) - -#define read_enc(addr) readl(cx->enc_mem + (u32)(addr)) -#define write_enc(val, addr) writel(val, cx->enc_mem + (u32)(addr)) -#define write_enc_sync(val, addr) \ - do { write_enc(val, addr); read_enc(addr); } while (0) - -#define sw1_irq_enable(val) do { \ - write_reg(val, SW1_INT_STATUS); \ - write_reg(read_reg(SW1_INT_ENABLE_PCI) | (val), SW1_INT_ENABLE_PCI); \ -} while (0) - -#define sw1_irq_disable(val) \ - write_reg(read_reg(SW1_INT_ENABLE_PCI) & ~(val), SW1_INT_ENABLE_PCI); - -#define sw2_irq_enable(val) do { \ - write_reg(val, SW2_INT_STATUS); \ - write_reg(read_reg(SW2_INT_ENABLE_PCI) | (val), SW2_INT_ENABLE_PCI); \ -} while (0) - -#define sw2_irq_disable(val) \ - write_reg(read_reg(SW2_INT_ENABLE_PCI) & ~(val), SW2_INT_ENABLE_PCI); - -#define setup_page(addr) do { \ - u32 val = read_reg(0xD000F8) & ~0x1f00; \ - write_reg(val | (((addr) >> 17) & 0x1f00), 0xD000F8); \ -} while (0) - #endif /* CX18_DRIVER_H */ |