diff options
Diffstat (limited to 'drivers/message/i2o/Kconfig')
| -rw-r--r-- | drivers/message/i2o/Kconfig | 121 |
1 files changed, 0 insertions, 121 deletions
diff --git a/drivers/message/i2o/Kconfig b/drivers/message/i2o/Kconfig deleted file mode 100644 index 5afa0e393ecf..000000000000 --- a/drivers/message/i2o/Kconfig +++ /dev/null @@ -1,121 +0,0 @@ - -menuconfig I2O - tristate "I2O device support" - depends on PCI - ---help--- - The Intelligent Input/Output (I2O) architecture allows hardware - drivers to be split into two parts: an operating system specific - module called the OSM and an hardware specific module called the - HDM. The OSM can talk to a whole range of HDM's, and ideally the - HDM's are not OS dependent. This allows for the same HDM driver to - be used under different operating systems if the relevant OSM is in - place. In order for this to work, you need to have an I2O interface - adapter card in your computer. This card contains a special I/O - processor (IOP), thus allowing high speeds since the CPU does not - have to deal with I/O. - - If you say Y here, you will get a choice of interface adapter - drivers and OSM's with the following questions. - - To compile this support as a module, choose M here: the - modules will be called i2o_core. - - If unsure, say N. - -if I2O - -config I2O_LCT_NOTIFY_ON_CHANGES - bool "Enable LCT notification" - default y - ---help--- - Only say N here if you have a I2O controller from SUN. The SUN - firmware doesn't support LCT notification on changes. If this option - is enabled on such a controller the driver will hang up in a endless - loop. On all other controllers say Y. - - If unsure, say Y. - -config I2O_EXT_ADAPTEC - bool "Enable Adaptec extensions" - default y - ---help--- - Say Y for support of raidutils for Adaptec I2O controllers. You also - have to say Y to "I2O Configuration support", "I2O SCSI OSM" below - and to "SCSI generic support" under "SCSI device configuration". - -config I2O_EXT_ADAPTEC_DMA64 - bool "Enable 64-bit DMA" - depends on I2O_EXT_ADAPTEC && ( 64BIT || HIGHMEM64G ) - default y - ---help--- - Say Y for support of 64-bit DMA transfer mode on Adaptec I2O - controllers. - Note: You need at least firmware version 3709. - -config I2O_CONFIG - tristate "I2O Configuration support" - depends on VIRT_TO_BUS - ---help--- - Say Y for support of the configuration interface for the I2O adapters. - If you have a RAID controller from Adaptec and you want to use the - raidutils to manage your RAID array, you have to say Y here. - - To compile this support as a module, choose M here: the - module will be called i2o_config. - - Note: If you want to use the new API you have to download the - i2o_config patch from http://i2o.shadowconnect.com/ - -config I2O_CONFIG_OLD_IOCTL - bool "Enable ioctls (OBSOLETE)" - depends on I2O_CONFIG - default y - ---help--- - Enables old ioctls. - -config I2O_BUS - tristate "I2O Bus Adapter OSM" - ---help--- - Include support for the I2O Bus Adapter OSM. The Bus Adapter OSM - provides access to the busses on the I2O controller. The main purpose - is to rescan the bus to find new devices. - - To compile this support as a module, choose M here: the - module will be called i2o_bus. - -config I2O_BLOCK - tristate "I2O Block OSM" - depends on BLOCK - ---help--- - Include support for the I2O Block OSM. The Block OSM presents disk - and other structured block devices to the operating system. If you - are using an RAID controller, you could access the array only by - the Block OSM driver. But it is possible to access the single disks - by the SCSI OSM driver, for example to monitor the disks. - - To compile this support as a module, choose M here: the - module will be called i2o_block. - -config I2O_SCSI - tristate "I2O SCSI OSM" - depends on SCSI - ---help--- - Allows direct SCSI access to SCSI devices on a SCSI or FibreChannel - I2O controller. You can use both the SCSI and Block OSM together if - you wish. To access a RAID array, you must use the Block OSM driver. - But you could use the SCSI OSM driver to monitor the single disks. - - To compile this support as a module, choose M here: the - module will be called i2o_scsi. - -config I2O_PROC - tristate "I2O /proc support" - ---help--- - If you say Y here and to "/proc file system support", you will be - able to read I2O related information from the virtual directory - /proc/i2o. - - To compile this support as a module, choose M here: the - module will be called i2o_proc. - -endif # I2O |