diff options
Diffstat (limited to 'drivers/misc/habanalabs/habanalabs.h')
| -rw-r--r-- | drivers/misc/habanalabs/habanalabs.h | 19 |
1 files changed, 13 insertions, 6 deletions
diff --git a/drivers/misc/habanalabs/habanalabs.h b/drivers/misc/habanalabs/habanalabs.h index 1ecdcf8b763a..194d83352696 100644 --- a/drivers/misc/habanalabs/habanalabs.h +++ b/drivers/misc/habanalabs/habanalabs.h @@ -578,8 +578,9 @@ enum hl_pll_frequency { * @mmu_invalidate_cache_range: flush specific MMU STLB cache lines with * ASID-VA-size mask. * @send_heartbeat: send is-alive packet to ArmCP and verify response. - * @enable_clock_gating: enable clock gating for reducing power consumption. - * @disable_clock_gating: disable clock for accessing registers on HBW. + * @set_clock_gating: enable/disable clock gating per engine according to + * clock gating mask in hdev + * @disable_clock_gating: disable clock gating completely * @debug_coresight: perform certain actions on Coresight for debugging. * @is_device_idle: return true if device is idle, false otherwise. * @soft_reset_late_init: perform certain actions needed after soft reset. @@ -587,7 +588,11 @@ enum hl_pll_frequency { * @hw_queues_unlock: release H/W queues lock. * @get_pci_id: retrieve PCI ID. * @get_eeprom_data: retrieve EEPROM data from F/W. - * @send_cpu_message: send buffer to ArmCP. + * @send_cpu_message: send message to F/W. If the message is timedout, the + * driver will eventually reset the device. The timeout can + * be determined by the calling function or it can be 0 and + * then the timeout is the default timeout for the specific + * ASIC * @get_hw_state: retrieve the H/W state * @pci_bars_map: Map PCI BARs. * @set_dram_bar_base: Set DRAM BAR to map specific device address. Returns @@ -680,7 +685,7 @@ struct hl_asic_funcs { int (*mmu_invalidate_cache_range)(struct hl_device *hdev, bool is_hard, u32 asid, u64 va, u64 size); int (*send_heartbeat)(struct hl_device *hdev); - void (*enable_clock_gating)(struct hl_device *hdev); + void (*set_clock_gating)(struct hl_device *hdev); void (*disable_clock_gating)(struct hl_device *hdev); int (*debug_coresight)(struct hl_device *hdev, void *data); bool (*is_device_idle)(struct hl_device *hdev, u32 *mask, @@ -1398,6 +1403,9 @@ struct hl_device_idle_busy_ts { * @max_power: the max power of the device, as configured by the sysadmin. This * value is saved so in case of hard-reset, the driver will restore * this value and update the F/W after the re-initialization + * @clock_gating_mask: is clock gating enabled. bitmask that represents the + * different engines. See debugfs-driver-habanalabs for + * details. * @in_reset: is device in reset flow. * @curr_pll_profile: current PLL profile. * @cs_active_cnt: number of active command submissions on this device (active @@ -1425,7 +1433,6 @@ struct hl_device_idle_busy_ts { * @init_done: is the initialization of the device done. * @mmu_enable: is MMU enabled. * @mmu_huge_page_opt: is MMU huge pages optimization enabled. - * @clock_gating: is clock gating enabled. * @device_cpu_disabled: is the device CPU disabled (due to timeouts) * @dma_mask: the dma mask that was set for this device * @in_debug: is device under debug. This, together with fpriv_list, enforces @@ -1493,6 +1500,7 @@ struct hl_device { atomic64_t dram_used_mem; u64 timeout_jiffies; u64 max_power; + u64 clock_gating_mask; atomic_t in_reset; enum hl_pll_frequency curr_pll_profile; int cs_active_cnt; @@ -1514,7 +1522,6 @@ struct hl_device { u8 dram_default_page_mapping; u8 pmmu_huge_range; u8 init_done; - u8 clock_gating; u8 device_cpu_disabled; u8 dma_mask; u8 in_debug; |