diff options
Diffstat (limited to 'drivers/mmc/host/mmci.c')
| -rw-r--r-- | drivers/mmc/host/mmci.c | 66 |
1 files changed, 45 insertions, 21 deletions
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index ec28d175d9c8..150772395cc6 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -33,6 +33,7 @@ #include <linux/amba/mmci.h> #include <linux/pm_runtime.h> #include <linux/types.h> +#include <linux/pinctrl/consumer.h> #include <asm/div64.h> #include <asm/io.h> @@ -654,9 +655,31 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data) /* The ST Micro variants has a special bit to enable SDIO */ if (variant->sdio && host->mmc->card) - if (mmc_card_sdio(host->mmc->card)) + if (mmc_card_sdio(host->mmc->card)) { + /* + * The ST Micro variants has a special bit + * to enable SDIO. + */ + u32 clk; + datactrl |= MCI_ST_DPSM_SDIOEN; + /* + * The ST Micro variant for SDIO small write transfers + * needs to have clock H/W flow control disabled, + * otherwise the transfer will not start. The threshold + * depends on the rate of MCLK. + */ + if (data->flags & MMC_DATA_WRITE && + (host->size < 8 || + (host->size <= 8 && host->mclk > 50000000))) + clk = host->clk_reg & ~variant->clkreg_enable; + else + clk = host->clk_reg | variant->clkreg_enable; + + mmci_write_clkreg(host, clk); + } + /* * Attempt to use DMA operation mode, if this * should fail, fall back to PIO mode @@ -840,14 +863,14 @@ static int mmci_pio_read(struct mmci_host *host, char *buffer, unsigned int rema if (unlikely(count & 0x3)) { if (count < 4) { unsigned char buf[4]; - readsl(base + MMCIFIFO, buf, 1); + ioread32_rep(base + MMCIFIFO, buf, 1); memcpy(ptr, buf, count); } else { - readsl(base + MMCIFIFO, ptr, count >> 2); + ioread32_rep(base + MMCIFIFO, ptr, count >> 2); count &= ~0x3; } } else { - readsl(base + MMCIFIFO, ptr, count >> 2); + ioread32_rep(base + MMCIFIFO, ptr, count >> 2); } ptr += count; @@ -877,22 +900,6 @@ static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int rem count = min(remain, maxcnt); /* - * The ST Micro variant for SDIO transfer sizes - * less then 8 bytes should have clock H/W flow - * control disabled. - */ - if (variant->sdio && - mmc_card_sdio(host->mmc->card)) { - u32 clk; - if (count < 8) - clk = host->clk_reg & ~variant->clkreg_enable; - else - clk = host->clk_reg | variant->clkreg_enable; - - mmci_write_clkreg(host, clk); - } - - /* * SDIO especially may want to send something that is * not divisible by 4 (as opposed to card sectors * etc), and the FIFO only accept full 32-bit writes. @@ -900,7 +907,7 @@ static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int rem * byte become a 32bit write, 7 bytes will be two * 32bit writes etc. */ - writesl(base + MMCIFIFO, ptr, (count + 3) >> 2); + iowrite32_rep(base + MMCIFIFO, ptr, (count + 3) >> 2); ptr += count; remain -= count; @@ -1360,6 +1367,23 @@ static int mmci_probe(struct amba_device *dev, mmc->f_max = min(host->mclk, fmax); dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max); + host->pinctrl = devm_pinctrl_get(&dev->dev); + if (IS_ERR(host->pinctrl)) { + ret = PTR_ERR(host->pinctrl); + goto clk_disable; + } + + host->pins_default = pinctrl_lookup_state(host->pinctrl, + PINCTRL_STATE_DEFAULT); + + /* enable pins to be muxed in and configured */ + if (!IS_ERR(host->pins_default)) { + ret = pinctrl_select_state(host->pinctrl, host->pins_default); + if (ret) + dev_warn(&dev->dev, "could not set default pins\n"); + } else + dev_warn(&dev->dev, "could not get default pinstate\n"); + #ifdef CONFIG_REGULATOR /* If we're using the regulator framework, try to fetch a regulator */ host->vcc = regulator_get(&dev->dev, "vmmc"); |