summaryrefslogtreecommitdiffstats
path: root/drivers/mmc/host
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mmc/host')
-rw-r--r--drivers/mmc/host/at91_mci.c3
-rw-r--r--drivers/mmc/host/atmel-mci.c19
-rw-r--r--drivers/mmc/host/au1xmmc.c1
-rw-r--r--drivers/mmc/host/bfin_sdh.c1
-rw-r--r--drivers/mmc/host/cb710-mmc.c1
-rw-r--r--drivers/mmc/host/mmc_spi.c1
-rw-r--r--drivers/mmc/host/mmci.c19
-rw-r--r--drivers/mmc/host/mmci.h6
-rw-r--r--drivers/mmc/host/msm_sdcc.c5
-rw-r--r--drivers/mmc/host/mxcmmc.c4
-rw-r--r--drivers/mmc/host/of_mmc_spi.c1
-rw-r--r--drivers/mmc/host/omap.c1
-rw-r--r--drivers/mmc/host/omap_hsmmc.c9
-rw-r--r--drivers/mmc/host/pxamci.c3
-rw-r--r--drivers/mmc/host/sdhci-pci.c1
-rw-r--r--drivers/mmc/host/sdhci-s3c.c1
-rw-r--r--drivers/mmc/host/sdhci.c1
-rw-r--r--drivers/mmc/host/wbsd.c1
18 files changed, 50 insertions, 28 deletions
diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c
index 91dc60cd032b..336d9f553f3e 100644
--- a/drivers/mmc/host/at91_mci.c
+++ b/drivers/mmc/host/at91_mci.c
@@ -65,6 +65,7 @@
#include <linux/dma-mapping.h>
#include <linux/clk.h>
#include <linux/atmel_pdc.h>
+#include <linux/gfp.h>
#include <linux/mmc/host.h>
@@ -313,8 +314,8 @@ static void at91_mci_post_dma_read(struct at91mci_host *host)
dmabuf = (unsigned *)tmpv;
}
+ flush_kernel_dcache_page(sg_page(sg));
kunmap_atomic(sgbuffer, KM_BIO_SRC_IRQ);
- dmac_flush_range((void *)sgbuffer, ((void *)sgbuffer) + amount);
data->bytes_xfered += amount;
if (size == 0)
break;
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 8072128e933b..fb279f4ed8b3 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -22,6 +22,7 @@
#include <linux/platform_device.h>
#include <linux/scatterlist.h>
#include <linux/seq_file.h>
+#include <linux/slab.h>
#include <linux/stat.h>
#include <linux/mmc/host.h>
@@ -265,7 +266,7 @@ static int atmci_req_show(struct seq_file *s, void *v)
"CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
cmd->opcode, cmd->arg, cmd->flags,
cmd->resp[0], cmd->resp[1], cmd->resp[2],
- cmd->resp[2], cmd->error);
+ cmd->resp[3], cmd->error);
if (data)
seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
data->bytes_xfered, data->blocks,
@@ -275,7 +276,7 @@ static int atmci_req_show(struct seq_file *s, void *v)
"CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
stop->opcode, stop->arg, stop->flags,
stop->resp[0], stop->resp[1], stop->resp[2],
- stop->resp[2], stop->error);
+ stop->resp[3], stop->error);
}
spin_unlock_bh(&slot->host->lock);
@@ -568,9 +569,10 @@ static void atmci_dma_cleanup(struct atmel_mci *host)
{
struct mmc_data *data = host->data;
- dma_unmap_sg(&host->pdev->dev, data->sg, data->sg_len,
- ((data->flags & MMC_DATA_WRITE)
- ? DMA_TO_DEVICE : DMA_FROM_DEVICE));
+ if (data)
+ dma_unmap_sg(&host->pdev->dev, data->sg, data->sg_len,
+ ((data->flags & MMC_DATA_WRITE)
+ ? DMA_TO_DEVICE : DMA_FROM_DEVICE));
}
static void atmci_stop_dma(struct atmel_mci *host)
@@ -1098,8 +1100,8 @@ static void atmci_command_complete(struct atmel_mci *host,
"command error: status=0x%08x\n", status);
if (cmd->data) {
- host->data = NULL;
atmci_stop_dma(host);
+ host->data = NULL;
mci_writel(host, IDR, MCI_NOTBUSY
| MCI_TXRDY | MCI_RXRDY
| ATMCI_DATA_ERROR_FLAGS);
@@ -1292,6 +1294,7 @@ static void atmci_tasklet_func(unsigned long priv)
} else {
data->bytes_xfered = data->blocks * data->blksz;
data->error = 0;
+ mci_writel(host, IDR, ATMCI_DATA_ERROR_FLAGS);
}
if (!data->stop) {
@@ -1750,13 +1753,13 @@ static int __init atmci_probe(struct platform_device *pdev)
ret = -ENODEV;
if (pdata->slot[0].bus_width) {
ret = atmci_init_slot(host, &pdata->slot[0],
- MCI_SDCSEL_SLOT_A, 0);
+ 0, MCI_SDCSEL_SLOT_A);
if (!ret)
nr_slots++;
}
if (pdata->slot[1].bus_width) {
ret = atmci_init_slot(host, &pdata->slot[1],
- MCI_SDCSEL_SLOT_B, 1);
+ 1, MCI_SDCSEL_SLOT_B);
if (!ret)
nr_slots++;
}
diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c
index 57b21198828f..f5834449400e 100644
--- a/drivers/mmc/host/au1xmmc.c
+++ b/drivers/mmc/host/au1xmmc.c
@@ -41,6 +41,7 @@
#include <linux/scatterlist.h>
#include <linux/leds.h>
#include <linux/mmc/host.h>
+#include <linux/slab.h>
#include <asm/io.h>
#include <asm/mach-au1x00/au1000.h>
diff --git a/drivers/mmc/host/bfin_sdh.c b/drivers/mmc/host/bfin_sdh.c
index 56f7b448b911..6919e844072c 100644
--- a/drivers/mmc/host/bfin_sdh.c
+++ b/drivers/mmc/host/bfin_sdh.c
@@ -17,6 +17,7 @@
#include <linux/dma-mapping.h>
#include <linux/mmc/host.h>
#include <linux/proc_fs.h>
+#include <linux/gfp.h>
#include <asm/cacheflush.h>
#include <asm/dma.h>
diff --git a/drivers/mmc/host/cb710-mmc.c b/drivers/mmc/host/cb710-mmc.c
index 4e72964a7b43..92a324f7417c 100644
--- a/drivers/mmc/host/cb710-mmc.c
+++ b/drivers/mmc/host/cb710-mmc.c
@@ -9,7 +9,6 @@
*/
#include <linux/kernel.h>
#include <linux/module.h>
-#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include "cb710-mmc.h"
diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c
index d55fe4fb7935..ad847a24a675 100644
--- a/drivers/mmc/host/mmc_spi.c
+++ b/drivers/mmc/host/mmc_spi.c
@@ -26,6 +26,7 @@
*/
#include <linux/sched.h>
#include <linux/delay.h>
+#include <linux/slab.h>
#include <linux/bio.h>
#include <linux/dma-mapping.h>
#include <linux/crc7.h>
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 84c103a7ee13..ff115d920888 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -55,14 +55,16 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
host->cclk = host->mclk / (2 * (clk + 1));
}
if (host->hw_designer == AMBA_VENDOR_ST)
- clk |= MCI_FCEN; /* Bug fix in ST IP block */
+ clk |= MCI_ST_FCEN; /* Bug fix in ST IP block */
clk |= MCI_CLK_ENABLE;
/* This hasn't proven to be worthwhile */
/* clk |= MCI_CLK_PWRSAVE; */
}
if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4)
- clk |= MCI_WIDE_BUS;
+ clk |= MCI_4BIT_BUS;
+ if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8)
+ clk |= MCI_ST_8BIT_BUS;
writel(clk, host->base + MMCICLOCK);
}
@@ -629,7 +631,18 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
mmc->ops = &mmci_ops;
mmc->f_min = (host->mclk + 511) / 512;
- mmc->f_max = min(host->mclk, fmax);
+ /*
+ * If the platform data supplies a maximum operating
+ * frequency, this takes precedence. Else, we fall back
+ * to using the module parameter, which has a (low)
+ * default value in case it is not specified. Either
+ * value must not exceed the clock rate into the block,
+ * of course.
+ */
+ if (plat->f_max)
+ mmc->f_max = min(host->mclk, plat->f_max);
+ else
+ mmc->f_max = min(host->mclk, fmax);
dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);
#ifdef CONFIG_REGULATOR
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 1ceb9a90f59b..d77062e5e3af 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -25,9 +25,11 @@
#define MCI_CLK_ENABLE (1 << 8)
#define MCI_CLK_PWRSAVE (1 << 9)
#define MCI_CLK_BYPASS (1 << 10)
-#define MCI_WIDE_BUS (1 << 11)
+#define MCI_4BIT_BUS (1 << 11)
+/* 8bit wide buses supported in ST Micro versions */
+#define MCI_ST_8BIT_BUS (1 << 12)
/* HW flow control on the ST Micro version */
-#define MCI_FCEN (1 << 13)
+#define MCI_ST_FCEN (1 << 13)
#define MMCIARGUMENT 0x008
#define MMCICOMMAND 0x00c
diff --git a/drivers/mmc/host/msm_sdcc.c b/drivers/mmc/host/msm_sdcc.c
index b31946e0b4ca..04ae884383f6 100644
--- a/drivers/mmc/host/msm_sdcc.c
+++ b/drivers/mmc/host/msm_sdcc.c
@@ -33,6 +33,7 @@
#include <linux/debugfs.h>
#include <linux/io.h>
#include <linux/memory.h>
+#include <linux/gfp.h>
#include <asm/cacheflush.h>
#include <asm/div64.h>
@@ -1250,9 +1251,7 @@ msmsdcc_resume(struct platform_device *dev)
if (mmc->card && mmc->card->type != MMC_TYPE_SDIO)
mmc_resume_host(mmc);
- if (host->stat_irq)
- enable_irq(host->stat_irq);
- else if (host->stat_irq)
+ if (host->stat_irq)
enable_irq(host->stat_irq);
}
return 0;
diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c
index 60a2b69e54f5..2df90412abb5 100644
--- a/drivers/mmc/host/mxcmmc.c
+++ b/drivers/mmc/host/mxcmmc.c
@@ -4,7 +4,7 @@
* This is a driver for the SDHC controller found in Freescale MX2/MX3
* SoCs. It is basically the same hardware as found on MX1 (imxmmc.c).
* Unlike the hardware found on MX1, this hardware just works and does
- * not need all the quirks found in imxmmc.c, hence the seperate driver.
+ * not need all the quirks found in imxmmc.c, hence the separate driver.
*
* Copyright (C) 2008 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de>
* Copyright (C) 2006 Pavel Pisa, PiKRON <ppisa@pikron.com>
@@ -708,7 +708,7 @@ static int mxcmci_probe(struct platform_device *pdev)
mmc->max_blk_size = 2048;
mmc->max_blk_count = 65535;
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
- mmc->max_seg_size = mmc->max_seg_size;
+ mmc->max_seg_size = mmc->max_req_size;
host = mmc_priv(mmc);
host->base = ioremap(r->start, resource_size(r));
diff --git a/drivers/mmc/host/of_mmc_spi.c b/drivers/mmc/host/of_mmc_spi.c
index 0c7a63c1f12f..bb6cc54b558e 100644
--- a/drivers/mmc/host/of_mmc_spi.c
+++ b/drivers/mmc/host/of_mmc_spi.c
@@ -14,6 +14,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/device.h>
+#include <linux/slab.h>
#include <linux/gpio.h>
#include <linux/of.h>
#include <linux/of_gpio.h>
diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
index c6d7e8ecadbf..84d280406341 100644
--- a/drivers/mmc/host/omap.c
+++ b/drivers/mmc/host/omap.c
@@ -26,6 +26,7 @@
#include <linux/clk.h>
#include <linux/scatterlist.h>
#include <linux/i2c/tps65010.h>
+#include <linux/slab.h>
#include <asm/io.h>
#include <asm/irq.h>
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 83f0affadcae..e9caf694c59e 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -1179,15 +1179,10 @@ static void omap_hsmmc_detect(struct work_struct *work)
carddetect = -ENOSYS;
}
- if (carddetect) {
+ if (carddetect)
mmc_detect_change(host->mmc, (HZ * 200) / 1000);
- } else {
- mmc_host_enable(host->mmc);
- omap_hsmmc_reset_controller_fsm(host, SRD);
- mmc_host_lazy_disable(host->mmc);
-
+ else
mmc_detect_change(host->mmc, (HZ * 50) / 1000);
- }
}
/*
diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c
index 0d783f3e79ed..e4f00e70a749 100644
--- a/drivers/mmc/host/pxamci.c
+++ b/drivers/mmc/host/pxamci.c
@@ -29,6 +29,7 @@
#include <linux/io.h>
#include <linux/regulator/consumer.h>
#include <linux/gpio.h>
+#include <linux/gfp.h>
#include <asm/sizes.h>
@@ -543,7 +544,7 @@ static irqreturn_t pxamci_detect_irq(int irq, void *devid)
{
struct pxamci_host *host = mmc_priv(devid);
- mmc_detect_change(devid, host->pdata->detect_delay);
+ mmc_detect_change(devid, msecs_to_jiffies(host->pdata->detect_delay_ms));
return IRQ_HANDLED;
}
diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c
index 8e1020cf73f4..6701af629c30 100644
--- a/drivers/mmc/host/sdhci-pci.c
+++ b/drivers/mmc/host/sdhci-pci.c
@@ -16,6 +16,7 @@
#include <linux/highmem.h>
#include <linux/pci.h>
#include <linux/dma-mapping.h>
+#include <linux/slab.h>
#include <linux/mmc/host.h>
diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
index 50997d2a63e7..2136794c0cfa 100644
--- a/drivers/mmc/host/sdhci-s3c.c
+++ b/drivers/mmc/host/sdhci-s3c.c
@@ -15,6 +15,7 @@
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/platform_device.h>
+#include <linux/slab.h>
#include <linux/clk.h>
#include <linux/io.h>
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index d6ab62d539fb..9d4fdfa685e5 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -17,6 +17,7 @@
#include <linux/highmem.h>
#include <linux/io.h>
#include <linux/dma-mapping.h>
+#include <linux/slab.h>
#include <linux/scatterlist.h>
#include <linux/leds.h>
diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c
index 89bf8cd25cac..69efe01eece8 100644
--- a/drivers/mmc/host/wbsd.c
+++ b/drivers/mmc/host/wbsd.c
@@ -34,6 +34,7 @@
#include <linux/highmem.h>
#include <linux/mmc/host.h>
#include <linux/scatterlist.h>
+#include <linux/slab.h>
#include <asm/io.h>
#include <asm/dma.h>