diff options
Diffstat (limited to 'drivers/mtd/devices/docg3.h')
| -rw-r--r-- | drivers/mtd/devices/docg3.h | 65 |
1 files changed, 61 insertions, 4 deletions
diff --git a/drivers/mtd/devices/docg3.h b/drivers/mtd/devices/docg3.h index 0d407be24594..db0da436b493 100644 --- a/drivers/mtd/devices/docg3.h +++ b/drivers/mtd/devices/docg3.h @@ -51,10 +51,19 @@ #define DOC_LAYOUT_WEAR_OFFSET (DOC_LAYOUT_PAGE_OOB_SIZE * 2) #define DOC_LAYOUT_BLOCK_SIZE \ (DOC_LAYOUT_PAGES_PER_BLOCK * DOC_LAYOUT_PAGE_SIZE) + +/* + * ECC related constants + */ +#define DOC_ECC_BCH_M 14 +#define DOC_ECC_BCH_T 4 +#define DOC_ECC_BCH_PRIMPOLY 0x4443 #define DOC_ECC_BCH_SIZE 7 #define DOC_ECC_BCH_COVERED_BYTES \ (DOC_LAYOUT_PAGE_SIZE + DOC_LAYOUT_OOB_PAGEINFO_SZ + \ - DOC_LAYOUT_OOB_HAMMING_SZ + DOC_LAYOUT_OOB_BCH_SZ) + DOC_LAYOUT_OOB_HAMMING_SZ) +#define DOC_ECC_BCH_TOTAL_BYTES \ + (DOC_ECC_BCH_COVERED_BYTES + DOC_LAYOUT_OOB_BCH_SZ) /* * Blocks distribution @@ -80,6 +89,7 @@ #define DOC_CHIPID_G3 0x200 #define DOC_ERASE_MARK 0xaa +#define DOC_MAX_NBFLOORS 4 /* * Flash registers */ @@ -105,9 +115,11 @@ #define DOC_ECCCONF1 0x1042 #define DOC_ECCPRESET 0x1044 #define DOC_HAMMINGPARITY 0x1046 -#define DOC_BCH_SYNDROM(idx) (0x1048 + (idx << 1)) +#define DOC_BCH_HW_ECC(idx) (0x1048 + idx) #define DOC_PROTECTION 0x1056 +#define DOC_DPS0_KEY 0x105c +#define DOC_DPS1_KEY 0x105e #define DOC_DPS0_ADDRLOW 0x1060 #define DOC_DPS0_ADDRHIGH 0x1062 #define DOC_DPS1_ADDRLOW 0x1064 @@ -117,6 +129,7 @@ #define DOC_ASICMODECONFIRM 0x1072 #define DOC_CHIPID_INV 0x1074 +#define DOC_POWERMODE 0x107c /* * Flash sequences @@ -124,11 +137,14 @@ */ #define DOC_SEQ_RESET 0x00 #define DOC_SEQ_PAGE_SIZE_532 0x03 -#define DOC_SEQ_SET_MODE 0x09 +#define DOC_SEQ_SET_FASTMODE 0x05 +#define DOC_SEQ_SET_RELIABLEMODE 0x09 #define DOC_SEQ_READ 0x12 #define DOC_SEQ_SET_PLANE1 0x0e #define DOC_SEQ_SET_PLANE2 0x10 #define DOC_SEQ_PAGE_SETUP 0x1d +#define DOC_SEQ_ERASE 0x27 +#define DOC_SEQ_PLANES_STATUS 0x31 /* * Flash commands @@ -143,7 +159,10 @@ #define DOC_CMD_PROG_BLOCK_ADDR 0x60 #define DOC_CMD_PROG_CYCLE1 0x80 #define DOC_CMD_PROG_CYCLE2 0x10 +#define DOC_CMD_PROG_CYCLE3 0x11 #define DOC_CMD_ERASECYCLE2 0xd0 +#define DOC_CMD_READ_STATUS 0x70 +#define DOC_CMD_PLANES_STATUS 0x71 #define DOC_CMD_RELIABLE_MODE 0x22 #define DOC_CMD_FAST_MODE 0xa2 @@ -174,6 +193,7 @@ /* * Flash register : DOC_ECCCONF0 */ +#define DOC_ECCCONF0_WRITE_MODE 0x0000 #define DOC_ECCCONF0_READ_MODE 0x8000 #define DOC_ECCCONF0_AUTO_ECC_ENABLE 0x4000 #define DOC_ECCCONF0_HAMMING_ENABLE 0x1000 @@ -185,7 +205,7 @@ */ #define DOC_ECCCONF1_BCH_SYNDROM_ERR 0x80 #define DOC_ECCCONF1_UNKOWN1 0x40 -#define DOC_ECCCONF1_UNKOWN2 0x20 +#define DOC_ECCCONF1_PAGE_IS_WRITTEN 0x20 #define DOC_ECCCONF1_UNKOWN3 0x10 #define DOC_ECCCONF1_HAMMING_BITS_MASK 0x0f @@ -223,13 +243,46 @@ #define DOC_READADDR_ONE_BYTE 0x4000 #define DOC_READADDR_ADDR_MASK 0x1fff +/* + * Flash register : DOC_POWERMODE + */ +#define DOC_POWERDOWN_READY 0x80 + +/* + * Status of erase and write operation + */ +#define DOC_PLANES_STATUS_FAIL 0x01 +#define DOC_PLANES_STATUS_PLANE0_KO 0x02 +#define DOC_PLANES_STATUS_PLANE1_KO 0x04 + +/* + * DPS key management + * + * Each floor of docg3 has 2 protection areas: DPS0 and DPS1. These areas span + * across block boundaries, and define whether these blocks can be read or + * written. + * The definition is dynamically stored in page 0 of blocks (2,3) for DPS0, and + * page 0 of blocks (4,5) for DPS1. + */ +#define DOC_LAYOUT_DPS_KEY_LENGTH 8 + /** * struct docg3 - DiskOnChip driver private data * @dev: the device currently under control * @base: mapped IO space * @device_id: number of the cascaded DoCG3 device (0, 1, 2 or 3) * @if_cfg: if true, reads are on 16bits, else reads are on 8bits + + * @reliable: if 0, docg3 in normal mode, if 1 docg3 in fast mode, if 2 in + * reliable mode + * Fast mode implies more errors than normal mode. + * Reliable mode implies that page 2*n and 2*n+1 are clones. * @bbt: bad block table cache + * @oob_write_ofs: offset of the MTD where this OOB should belong (ie. in next + * page_write) + * @oob_autoecc: if 1, use only bytes 0-7, 15, and fill the others with HW ECC + * if 0, use all the 16 bytes. + * @oob_write_buf: prepared OOB for next page_write * @debugfs_root: debugfs root node */ struct docg3 { @@ -237,8 +290,12 @@ struct docg3 { void __iomem *base; unsigned int device_id:4; unsigned int if_cfg:1; + unsigned int reliable:2; int max_block; u8 *bbt; + loff_t oob_write_ofs; + int oob_autoecc; + u8 oob_write_buf[DOC_LAYOUT_OOB_SIZE]; struct dentry *debugfs_root; }; |