diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 225 |
1 files changed, 71 insertions, 154 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 2683ee32fc11..fa533c27052a 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -26,14 +26,6 @@ menuconfig NETDEVICES # that for each of the symbols. if NETDEVICES -config NETDEVICES_MULTIQUEUE - bool "Netdevice multiple hardware queue support" - ---help--- - Say Y here if you want to allow the network stack to use multiple - hardware TX queues on an ethernet device. - - Most people will say N here. - config IFB tristate "Intermediate Functional Block support" depends on NET_CLS_ACT @@ -333,15 +325,6 @@ config APNE To compile this driver as a module, choose M here: the module will be called apne. -config APOLLO_ELPLUS - tristate "Apollo 3c505 support" - depends on APOLLO - help - Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card. - If you don't have one made for Apollos, you can use one from a PC, - except that your Apollo won't be able to boot from it (because the - code in the ROM will be for a PC). - config MAC8390 bool "Macintosh NS 8390 based ethernet cards" depends on MAC @@ -524,6 +507,18 @@ config STNIC If unsure, say N. +config SH_ETH + tristate "Renesas SuperH Ethernet support" + depends on SUPERH && \ + (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712) + select CRC32 + select MII + select MDIO_BITBANG + select PHYLIB + help + Renesas SuperH Ethernet device driver. + This driver support SH7710 and SH7712. + config SUNLANCE tristate "Sun LANCE support" depends on SBUS @@ -926,6 +921,23 @@ config DM9000 To compile this driver as a module, choose M here. The module will be called dm9000. +config DM9000_DEBUGLEVEL + int "DM9000 maximum debug level" + depends on DM9000 + default 4 + help + The maximum level of debugging code compiled into the DM9000 + driver. + +config DM9000_FORCE_SIMPLE_PHY_POLL + bool "Force simple NSR based PHY polling" + depends on DM9000 + ---help--- + This configuration forces the DM9000 to use the NSR's LinkStatus + bit to determine if the link is up or down instead of the more + costly MII PHY reads. Note, this will not work if the chip is + operating with an external PHY. + config ENC28J60 tristate "ENC28J60 support" depends on EXPERIMENTAL && SPI && NET_ETHERNET @@ -943,19 +955,11 @@ config ENC28J60_WRITEVERIFY Enable the verify after the buffer write useful for debugging purpose. If unsure, say N. -config DM9000_DEBUGLEVEL - int "DM9000 maximum debug level" - depends on DM9000 - default 4 - help - The maximum level of debugging code compiled into the DM9000 - driver. - config SMC911X tristate "SMSC LAN911[5678] support" select CRC32 select MII - depends on ARCH_PXA || SH_MAGIC_PANEL_R2 + depends on ARCH_PXA || SUPERH help This is a driver for SMSC's LAN911x series of Ethernet chipsets including the new LAN9115, LAN9116, LAN9117, and LAN9118. @@ -1243,7 +1247,6 @@ config IBMVETH To compile this driver as a module, choose M here. The module will be called ibmveth. -source "drivers/net/ibm_emac/Kconfig" source "drivers/net/ibm_newemac/Kconfig" config NET_PCI @@ -1286,20 +1289,6 @@ config AMD8111_ETH To compile this driver as a module, choose M here. The module will be called amd8111e. -config AMD8111E_NAPI - bool "Use RX polling (NAPI)" - depends on AMD8111_ETH - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config ADAPTEC_STARFIRE tristate "Adaptec Starfire/DuraLAN support" depends on NET_PCI && PCI @@ -1314,20 +1303,6 @@ config ADAPTEC_STARFIRE To compile this driver as a module, choose M here: the module will be called starfire. This is recommended. -config ADAPTEC_STARFIRE_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on ADAPTEC_STARFIRE && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config AC3200 tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)" depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL @@ -1670,7 +1645,7 @@ config SUNDANCE_MMIO config TLAN tristate "TI ThunderLAN support" - depends on NET_PCI && (PCI || EISA) && !64BIT + depends on NET_PCI && (PCI || EISA) ---help--- If you have a PCI Ethernet network card based on the ThunderLAN chip which is supported by this driver, say Y and read the @@ -1710,26 +1685,6 @@ config VIA_RHINE_MMIO If unsure, say Y. -config VIA_RHINE_NAPI - bool "Use Rx Polling (NAPI)" - depends on VIA_RHINE - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - -config LAN_SAA9730 - bool "Philips SAA9730 Ethernet support" - depends on NET_PCI && PCI && MIPS_ATLAS - help - The SAA9730 is a combined multimedia and peripheral controller used - in thin clients, Internet access terminals, and diskless - workstations. - See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>. - config SC92031 tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)" depends on NET_PCI && PCI && EXPERIMENTAL @@ -1971,20 +1926,6 @@ config E1000 To compile this driver as a module, choose M here. The module will be called e1000. -config E1000_NAPI - bool "Use Rx Polling (NAPI)" - depends on E1000 - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config E1000_DISABLE_PACKET_SPLIT bool "Disable Packet Split for PCI express adapters" depends on E1000 @@ -2013,9 +1954,6 @@ config E1000E To compile this driver as a module, choose M here. The module will be called e1000e. -config E1000E_ENABLED - def_bool E1000E != n - config IP1000 tristate "IP1000 Gigabit Ethernet support" depends on PCI && EXPERIMENTAL @@ -2047,6 +1985,15 @@ config IGB To compile this driver as a module, choose M here. The module will be called igb. +config IGB_LRO + bool "Use software LRO" + depends on IGB && INET + select INET_LRO + ---help--- + Say Y here if you want to use large receive offload. + + If in doubt, say N. + source "drivers/net/ixp2000/Kconfig" config MYRI_SBUS @@ -2104,27 +2051,13 @@ config R8169 To compile this driver as a module, choose M here: the module will be called r8169. This is recommended. -config R8169_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on R8169 && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config R8169_VLAN bool "VLAN support" depends on R8169 && VLAN_8021Q ---help--- Say Y here for the r8169 driver to support the functions required by the kernel 802.1Q code. - + If in doubt, say Y. config SB1250_MAC @@ -2227,6 +2160,7 @@ config VIA_VELOCITY config TIGON3 tristate "Broadcom Tigon3 support" depends on PCI + select PHYLIB help This driver supports Broadcom Tigon3 based gigabit Ethernet cards. @@ -2282,6 +2216,19 @@ config GELIC_WIRELESS the driver automatically distinguishes the models, you can safely enable this option even if you have a wireless-less model. +config GELIC_WIRELESS_OLD_PSK_INTERFACE + bool "PS3 Wireless private PSK interface (OBSOLETE)" + depends on GELIC_WIRELESS + help + This option retains the obsolete private interface to pass + the PSK from user space programs to the driver. The PSK + stands for 'Pre Shared Key' and is used for WPA[2]-PSK + (WPA-Personal) environment. + If WPA[2]-PSK is used and you need to use old programs that + support only this old interface, say Y. Otherwise N. + + If unsure, say N. + config GIANFAR tristate "Gianfar Ethernet" depends on FSL_SOC @@ -2291,10 +2238,6 @@ config GIANFAR This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, and MPC86xx family of chips, and the FEC on the 8540. -config GFAR_NAPI - bool "Use Rx Polling (NAPI)" - depends on GIANFAR - config UCC_GETH tristate "Freescale QE Gigabit Ethernet" depends on QUICC_ENGINE @@ -2303,10 +2246,6 @@ config UCC_GETH This driver supports the Gigabit Ethernet mode of the QUICC Engine, which is available on some Freescale SOCs. -config UGETH_NAPI - bool "Use Rx Polling (NAPI)" - depends on UCC_GETH - config UGETH_MAGIC_PACKET bool "Magic Packet detection support" depends on UCC_GETH @@ -2351,6 +2290,17 @@ config ATL1 To compile this driver as a module, choose M here. The module will be called atl1. +config ATL1E + tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)" + depends on PCI && EXPERIMENTAL + select CRC32 + select MII + help + This driver supports the Atheros L1E gigabit ethernet adapter. + + To compile this driver as a module, choose M here. The module + will be called atl1e. + endif # NETDEV_1000 # @@ -2396,18 +2346,11 @@ config CHELSIO_T1_1G Enables support for Chelsio's gigabit Ethernet PCI cards. If you are using only 10G cards say 'N' here. -config CHELSIO_T1_NAPI - bool "Use Rx Polling (NAPI)" - depends on CHELSIO_T1 - default y - help - NAPI is a driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. - config CHELSIO_T3 tristate "Chelsio Communications T3 10Gb Ethernet support" - depends on PCI + depends on PCI && INET select FW_LOADER + select INET_LRO help This driver supports Chelsio T3-based gigabit and 10Gb Ethernet adapters. @@ -2435,7 +2378,8 @@ config EHEA config IXGBE tristate "Intel(R) 10GbE PCI Express adapters support" - depends on PCI + depends on PCI && INET + select INET_LRO ---help--- This driver supports Intel(R) 10GbE PCI Express family of adapters. For more information on how to identify your adapter, go @@ -2473,20 +2417,6 @@ config IXGB To compile this driver as a module, choose M here. The module will be called ixgb. -config IXGB_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on IXGB && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config S2IO tristate "S2IO 10Gbe XFrame NIC" depends on PCI @@ -2495,20 +2425,6 @@ config S2IO More specific information on configuring the driver is in <file:Documentation/networking/s2io.txt>. -config S2IO_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on S2IO && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config MYRI10GE tristate "Myricom Myri-10G Ethernet support" depends on PCI && INET @@ -2573,6 +2489,7 @@ config BNX2X tristate "Broadcom NetXtremeII 10Gb support" depends on PCI select ZLIB_INFLATE + select LIBCRC32C help This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards. To compile this driver as a module, choose M here: the module |