diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 66 |
1 files changed, 53 insertions, 13 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 6bdfd47d679d..f062b424704e 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -26,6 +26,15 @@ menuconfig NETDEVICES # that for each of the symbols. if NETDEVICES +config COMPAT_NET_DEV_OPS + default y + bool "Enable older network device API compatiablity" + ---help--- + This option enables kernel compatiability with older network devices + that do not use net_device_ops interface. + + If unsure, say Y. + config IFB tristate "Intermediate Functional Block support" depends on NET_CLS_ACT @@ -963,6 +972,14 @@ config ENC28J60_WRITEVERIFY Enable the verify after the buffer write useful for debugging purpose. If unsure, say N. +config ETHOC + tristate "OpenCores 10/100 Mbps Ethernet MAC support" + depends on NET_ETHERNET + select MII + select PHYLIB + help + Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC. + config SMC911X tristate "SMSC LAN911[5678] support" select CRC32 @@ -1040,6 +1057,17 @@ config NI65 To compile this driver as a module, choose M here. The module will be called ni65. +config DNET + tristate "Dave ethernet support (DNET)" + depends on NET_ETHERNET && HAS_IOMEM + select PHYLIB + help + The Dave ethernet interface (DNET) is found on Qong Board FPGA. + Say Y to include support for the DNET chip. + + To compile this driver as a module, choose M here: the module + will be called dnet. + source "drivers/net/tulip/Kconfig" config AT1700 @@ -1829,10 +1857,10 @@ config 68360_ENET config FEC bool "FEC ethernet controller (of ColdFire CPUs)" - depends on M523x || M527x || M5272 || M528x || M520x || M532x + depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 help Say Y here if you want to use the built-in 10/100 Fast ethernet - controller on some Motorola ColdFire processors. + controller on some Motorola ColdFire and Freescale i.MX processors. config FEC2 bool "Second FEC ethernet controller (on some ColdFire CPUs)" @@ -2019,15 +2047,6 @@ config IGB To compile this driver as a module, choose M here. The module will be called igb. -config IGB_LRO - bool "Use software LRO" - depends on IGB && INET - select INET_LRO - ---help--- - Say Y here if you want to use large receive offload. - - If in doubt, say N. - config IGB_DCA bool "Direct Cache Access (DCA) Support" default y @@ -2273,9 +2292,17 @@ config GELIC_WIRELESS_OLD_PSK_INTERFACE If unsure, say N. +config FSL_PQ_MDIO + tristate "Freescale PQ MDIO" + depends on FSL_SOC + select PHYLIB + help + This driver supports the MDIO bus used by the gianfar and UCC drivers. + config GIANFAR tristate "Gianfar Ethernet" depends on FSL_SOC + select FSL_PQ_MDIO select PHYLIB select CRC32 help @@ -2285,6 +2312,7 @@ config GIANFAR config UCC_GETH tristate "Freescale QE Gigabit Ethernet" depends on QUICC_ENGINE + select FSL_PQ_MDIO select PHYLIB help This driver supports the Gigabit Ethernet mode of the QUICC Engine, @@ -2301,6 +2329,7 @@ config UGETH_TX_ON_DEMAND config MV643XX_ETH tristate "Marvell Discovery (643XX) and Orion ethernet support" depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION + select INET_LRO select PHYLIB help This driver supports the gigabit ethernet MACs in the @@ -2342,6 +2371,17 @@ config ATL1E To compile this driver as a module, choose M here. The module will be called atl1e. +config ATL1C + tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)" + depends on PCI && EXPERIMENTAL + select CRC32 + select MII + help + This driver supports the Atheros L1C gigabit ethernet adapter. + + To compile this driver as a module, choose M here. The module + will be called atl1c. + config JME tristate "JMicron(R) PCI-Express Gigabit Ethernet support" depends on PCI @@ -2408,7 +2448,6 @@ config CHELSIO_T3 tristate "Chelsio Communications T3 10Gb Ethernet support" depends on CHELSIO_T3_DEPENDS select FW_LOADER - select INET_LRO help This driver supports Chelsio T3-based gigabit and 10Gb Ethernet adapters. @@ -2444,7 +2483,6 @@ config ENIC config IXGBE tristate "Intel(R) 10GbE PCI Express adapters support" depends on PCI && INET - select INET_LRO ---help--- This driver supports Intel(R) 10GbE PCI Express family of adapters. For more information on how to identify your adapter, go @@ -2608,6 +2646,8 @@ config QLGE source "drivers/net/sfc/Kconfig" +source "drivers/net/benet/Kconfig" + endif # NETDEV_10000 source "drivers/net/tokenring/Kconfig" |