diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 50 |
1 files changed, 36 insertions, 14 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 0ba5b8e50a7c..dbd26f992158 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -483,7 +483,7 @@ config XTENSA_XT2000_SONIC This is the driver for the onboard card of the Xtensa XT2000 board. config MIPS_AU1X00_ENET - bool "MIPS AU1000 Ethernet support" + tristate "MIPS AU1000 Ethernet support" depends on SOC_AU1X00 select PHYLIB select CRC32 @@ -1916,6 +1916,7 @@ config FEC bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)" depends on M523x || M527x || M5272 || M528x || M520x || M532x || \ MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5 + select PHYLIB help Say Y here if you want to use the built-in 10/100 Fast ethernet controller on some Motorola ColdFire and Freescale i.MX processors. @@ -2434,8 +2435,8 @@ config MV643XX_ETH config XILINX_LL_TEMAC tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver" + depends on PPC || MICROBLAZE select PHYLIB - depends on PPC_DCR_NATIVE help This driver supports the Xilinx 10/100/1000 LocalLink TEMAC core used in Xilinx Spartan and Virtex FPGAs @@ -2582,6 +2583,31 @@ config CHELSIO_T3 To compile this driver as a module, choose M here: the module will be called cxgb3. +config CHELSIO_T4_DEPENDS + tristate + depends on PCI && INET + default y + +config CHELSIO_T4 + tristate "Chelsio Communications T4 Ethernet support" + depends on CHELSIO_T4_DEPENDS + select FW_LOADER + select MDIO + help + This driver supports Chelsio T4-based gigabit and 10Gb Ethernet + adapters. + + For general information about Chelsio and our products, visit + our website at <http://www.chelsio.com>. + + For customer support, please visit our customer support page at + <http://www.chelsio.com/support.htm>. + + Please send feedback to <linux-bugs@chelsio.com>. + + To compile this driver as a module choose M here; the module + will be called cxgb4. + config EHEA tristate "eHEA Ethernet support" depends on IBMEBUS && INET && SPARSEMEM @@ -2593,11 +2619,11 @@ config EHEA will be called ehea. config ENIC - tristate "Cisco 10G Ethernet NIC support" + tristate "Cisco VIC Ethernet NIC Support" depends on PCI && INET select INET_LRO help - This enables the support for the Cisco 10G Ethernet card. + This enables the support for the Cisco VIC Ethernet card. config IXGBE tristate "Intel(R) 10GbE PCI Express adapters support" @@ -2837,6 +2863,8 @@ source "drivers/ieee802154/Kconfig" source "drivers/s390/net/Kconfig" +source "drivers/net/caif/Kconfig" + config XEN_NETDEV_FRONTEND tristate "Xen network device frontend driver" depends on XEN @@ -3155,17 +3183,12 @@ config PPPOATM config PPPOL2TP tristate "PPP over L2TP (EXPERIMENTAL)" - depends on EXPERIMENTAL && PPP && INET + depends on EXPERIMENTAL && L2TP && PPP help Support for PPP-over-L2TP socket family. L2TP is a protocol used by ISPs and enterprises to tunnel PPP traffic over UDP tunnels. L2TP is replacing PPTP for VPN uses. - This kernel component handles only L2TP data packets: a - userland daemon handles L2TP the control protocol (tunnel - and session setup). One such daemon is OpenL2TP - (http://openl2tp.sourceforge.net/). - config SLIP tristate "SLIP (serial line) support" ---help--- @@ -3252,15 +3275,14 @@ config NET_FC "SCSI generic support". config NETCONSOLE - tristate "Network console logging support (EXPERIMENTAL)" - depends on EXPERIMENTAL + tristate "Network console logging support" ---help--- If you want to log kernel messages over the network, enable this. See <file:Documentation/networking/netconsole.txt> for details. config NETCONSOLE_DYNAMIC - bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)" - depends on NETCONSOLE && SYSFS && EXPERIMENTAL + bool "Dynamic reconfiguration of logging targets" + depends on NETCONSOLE && SYSFS select CONFIGFS_FS help This option enables the ability to dynamically reconfigure target |