1 files changed, 11 insertions, 39 deletions

diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 2381cb76f17c..ab4db5266f14 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -2641,18 +2641,8 @@ static void e1000_configure(struct e1000_adapter *adapter)
  **/
 void e1000e_power_up_phy(struct e1000_adapter *adapter)
 {
-	u16 mii_reg = 0;
-
-	/* Just clear the power down bit to wake the phy back up */
-	if (adapter->hw.phy.media_type == e1000_media_type_copper) {
-		/*
-		 * According to the manual, the phy will retain its
-		 * settings across a power-down/up cycle
-		 */
-		e1e_rphy(&adapter->hw, PHY_CONTROL, &mii_reg);
-		mii_reg &= ~MII_CR_POWER_DOWN;
-		e1e_wphy(&adapter->hw, PHY_CONTROL, mii_reg);
-	}
+	if (adapter->hw.phy.ops.power_up)
+		adapter->hw.phy.ops.power_up(&adapter->hw);
 
 	adapter->hw.mac.ops.setup_link(&adapter->hw);
 }
@@ -2660,35 +2650,17 @@ void e1000e_power_up_phy(struct e1000_adapter *adapter)
 /**
  * e1000_power_down_phy - Power down the PHY
  *
- * Power down the PHY so no link is implied when interface is down
- * The PHY cannot be powered down is management or WoL is active
+ * Power down the PHY so no link is implied when interface is down.
+ * The PHY cannot be powered down if management or WoL is active.
  */
 static void e1000_power_down_phy(struct e1000_adapter *adapter)
 {
-	struct e1000_hw *hw = &adapter->hw;
-	u16 mii_reg;
-
 	/* WoL is enabled */
 	if (adapter->wol)
 		return;
 
-	/* non-copper PHY? */
-	if (adapter->hw.phy.media_type != e1000_media_type_copper)
-		return;
-
-	/* reset is blocked because of a SoL/IDER session */
-	if (e1000e_check_mng_mode(hw) || e1000_check_reset_block(hw))
-		return;
-
-	/* manageability (AMT) is enabled */
-	if (er32(MANC) & E1000_MANC_SMBUS_EN)
-		return;
-
-	/* power down the PHY */
-	e1e_rphy(hw, PHY_CONTROL, &mii_reg);
-	mii_reg |= MII_CR_POWER_DOWN;
-	e1e_wphy(hw, PHY_CONTROL, mii_reg);
-	mdelay(1);
+	if (adapter->hw.phy.ops.power_down)
+		adapter->hw.phy.ops.power_down(&adapter->hw);
 }
 
 /**
@@ -5294,17 +5266,17 @@ static void __devexit e1000_remove(struct pci_dev *pdev)
 	cancel_work_sync(&adapter->print_hang_task);
 	flush_scheduled_work();
 
+	if (!(netdev->flags & IFF_UP))
+		e1000_power_down_phy(adapter);
+
+	unregister_netdev(netdev);
+
 	/*
 	 * Release control of h/w to f/w.  If f/w is AMT enabled, this
 	 * would have already happened in close and is redundant.
 	 */
 	e1000_release_hw_control(adapter);
 
-	unregister_netdev(netdev);
-
-	if (!e1000_check_reset_block(&adapter->hw))
-		e1000_phy_hw_reset(&adapter->hw);
-
 	e1000e_reset_interrupt_capability(adapter);
 	kfree(adapter->tx_ring);
 	kfree(adapter->rx_ring);