summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000e')
-rw-r--r--drivers/net/e1000e/defines.h2
-rw-r--r--drivers/net/e1000e/e1000.h16
-rw-r--r--drivers/net/e1000e/ethtool.c12
-rw-r--r--drivers/net/e1000e/hw.h1
-rw-r--r--drivers/net/e1000e/ich8lan.c484
-rw-r--r--drivers/net/e1000e/netdev.c50
-rw-r--r--drivers/net/e1000e/phy.c71
7 files changed, 477 insertions, 159 deletions
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h
index c0f185beb8bc..1190167a8b3d 100644
--- a/drivers/net/e1000e/defines.h
+++ b/drivers/net/e1000e/defines.h
@@ -76,6 +76,7 @@
/* Extended Device Control */
#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
@@ -347,6 +348,7 @@
/* Extended Configuration Control and Size */
#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008
#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000
#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 405a144ebcad..3e187b0e4203 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -141,6 +141,22 @@ struct e1000_info;
#define HV_TNCRS_UPPER PHY_REG(778, 29) /* Transmit with no CRS */
#define HV_TNCRS_LOWER PHY_REG(778, 30)
+#define E1000_FCRTV_PCH 0x05F40 /* PCH Flow Control Refresh Timer Value */
+
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS 17
+#define BM_CS_STATUS_LINK_UP 0x0400
+#define BM_CS_STATUS_RESOLVED 0x0800
+#define BM_CS_STATUS_SPEED_MASK 0xC000
+#define BM_CS_STATUS_SPEED_1000 0x8000
+
+/* 82577 Mobile Phy Status Register */
+#define HV_M_STATUS 26
+#define HV_M_STATUS_AUTONEG_COMPLETE 0x1000
+#define HV_M_STATUS_SPEED_MASK 0x0300
+#define HV_M_STATUS_SPEED_1000 0x0200
+#define HV_M_STATUS_LINK_UP 0x0040
+
enum e1000_boards {
board_82571,
board_82572,
diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c
index 1bf4d2a5d34f..e82638ecae88 100644
--- a/drivers/net/e1000e/ethtool.c
+++ b/drivers/net/e1000e/ethtool.c
@@ -327,10 +327,18 @@ static int e1000_set_pauseparam(struct net_device *netdev,
hw->fc.current_mode = hw->fc.requested_mode;
- retval = ((hw->phy.media_type == e1000_media_type_fiber) ?
- hw->mac.ops.setup_link(hw) : e1000e_force_mac_fc(hw));
+ if (hw->phy.media_type == e1000_media_type_fiber) {
+ retval = hw->mac.ops.setup_link(hw);
+ /* implicit goto out */
+ } else {
+ retval = e1000e_force_mac_fc(hw);
+ if (retval)
+ goto out;
+ e1000e_set_fc_watermarks(hw);
+ }
}
+out:
clear_bit(__E1000_RESETTING, &adapter->state);
return retval;
}
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index 7b05cf47f7f5..aaea41ef794d 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -903,6 +903,7 @@ struct e1000_shadow_ram {
struct e1000_dev_spec_ich8lan {
bool kmrn_lock_loss_workaround_enabled;
struct e1000_shadow_ram shadow_ram[E1000_ICH8_SHADOW_RAM_WORDS];
+ bool nvm_k1_enabled;
};
struct e1000_hw {
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index b6388b9535fd..eff3f4783655 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -124,11 +124,25 @@
#define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in milliseconds */
+/* SMBus Address Phy Register */
+#define HV_SMB_ADDR PHY_REG(768, 26)
+#define HV_SMB_ADDR_PEC_EN 0x0200
+#define HV_SMB_ADDR_VALID 0x0080
+
+/* Strapping Option Register - RO */
+#define E1000_STRAP 0x0000C
+#define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000
+#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
+
/* OEM Bits Phy Register */
#define HV_OEM_BITS PHY_REG(768, 25)
#define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */
+#define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */
#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
+#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
+#define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */
+
/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
/* Offset 04h HSFSTS */
union ich8_hws_flash_status {
@@ -208,6 +222,9 @@ static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw);
static s32 e1000_led_on_pchlan(struct e1000_hw *hw);
static s32 e1000_led_off_pchlan(struct e1000_hw *hw);
static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
+static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw);
+static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
+static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
{
@@ -483,14 +500,6 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
goto out;
}
- if (hw->mac.type == e1000_pchlan) {
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_K1_CONFIG,
- E1000_KMRNCTRLSTA_K1_ENABLE);
- if (ret_val)
- goto out;
- }
-
/*
* First we want to see if the MII Status Register reports
* link. If so, then we want to get the current speed/duplex
@@ -500,6 +509,12 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
if (ret_val)
goto out;
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000_k1_gig_workaround_hv(hw, link);
+ if (ret_val)
+ goto out;
+ }
+
if (!link)
goto out; /* No link detected */
@@ -794,6 +809,327 @@ static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw)
}
/**
+ * e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ *
+ * SW should configure the LCD from the NVM extended configuration region
+ * as a workaround for certain parts.
+ **/
+static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask;
+ s32 ret_val;
+ u16 word_addr, reg_data, reg_addr, phy_page = 0;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Initialize the PHY from the NVM on ICH platforms. This
+ * is needed due to an issue where the NVM configuration is
+ * not properly autoloaded after power transitions.
+ * Therefore, after each PHY reset, we will load the
+ * configuration data out of the NVM manually.
+ */
+ if ((hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) ||
+ (hw->mac.type == e1000_pchlan)) {
+ struct e1000_adapter *adapter = hw->adapter;
+
+ /* Check if SW needs to configure the PHY */
+ if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
+ (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M) ||
+ (hw->mac.type == e1000_pchlan))
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
+ else
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
+
+ data = er32(FEXTNVM);
+ if (!(data & sw_cfg_mask))
+ goto out;
+
+ /* Wait for basic configuration completes before proceeding */
+ e1000_lan_init_done_ich8lan(hw);
+
+ /*
+ * Make sure HW does not configure LCD from PHY
+ * extended configuration before SW configuration
+ */
+ data = er32(EXTCNF_CTRL);
+ if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
+ goto out;
+
+ cnf_size = er32(EXTCNF_SIZE);
+ cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
+ cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
+ if (!cnf_size)
+ goto out;
+
+ cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
+ cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
+
+ if (!(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) &&
+ (hw->mac.type == e1000_pchlan)) {
+ /*
+ * HW configures the SMBus address and LEDs when the
+ * OEM and LCD Write Enable bits are set in the NVM.
+ * When both NVM bits are cleared, SW will configure
+ * them instead.
+ */
+ data = er32(STRAP);
+ data &= E1000_STRAP_SMBUS_ADDRESS_MASK;
+ reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT;
+ reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
+ ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ data = er32(LEDCTL);
+ ret_val = e1000_write_phy_reg_hv_locked(hw,
+ HV_LED_CONFIG,
+ (u16)data);
+ if (ret_val)
+ goto out;
+ }
+ /* Configure LCD from extended configuration region. */
+
+ /* cnf_base_addr is in DWORD */
+ word_addr = (u16)(cnf_base_addr << 1);
+
+ for (i = 0; i < cnf_size; i++) {
+ ret_val = e1000_read_nvm(hw, (word_addr + i * 2), 1,
+ &reg_data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000_read_nvm(hw, (word_addr + i * 2 + 1),
+ 1, &reg_addr);
+ if (ret_val)
+ goto out;
+
+ /* Save off the PHY page for future writes. */
+ if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
+ phy_page = reg_data;
+ continue;
+ }
+
+ reg_addr &= PHY_REG_MASK;
+ reg_addr |= phy_page;
+
+ ret_val = phy->ops.write_phy_reg_locked(hw,
+ (u32)reg_addr,
+ reg_data);
+ if (ret_val)
+ goto out;
+ }
+ }
+
+out:
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+}
+
+/**
+ * e1000_k1_gig_workaround_hv - K1 Si workaround
+ * @hw: pointer to the HW structure
+ * @link: link up bool flag
+ *
+ * If K1 is enabled for 1Gbps, the MAC might stall when transitioning
+ * from a lower speed. This workaround disables K1 whenever link is at 1Gig
+ * If link is down, the function will restore the default K1 setting located
+ * in the NVM.
+ **/
+static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link)
+{
+ s32 ret_val = 0;
+ u16 status_reg = 0;
+ bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled;
+
+ if (hw->mac.type != e1000_pchlan)
+ goto out;
+
+ /* Wrap the whole flow with the sw flag */
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ /* Disable K1 when link is 1Gbps, otherwise use the NVM setting */
+ if (link) {
+ if (hw->phy.type == e1000_phy_82578) {
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw,
+ BM_CS_STATUS,
+ &status_reg);
+ if (ret_val)
+ goto release;
+
+ status_reg &= BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_MASK;
+
+ if (status_reg == (BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_1000))
+ k1_enable = false;
+ }
+
+ if (hw->phy.type == e1000_phy_82577) {
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw,
+ HV_M_STATUS,
+ &status_reg);
+ if (ret_val)
+ goto release;
+
+ status_reg &= HV_M_STATUS_LINK_UP |
+ HV_M_STATUS_AUTONEG_COMPLETE |
+ HV_M_STATUS_SPEED_MASK;
+
+ if (status_reg == (HV_M_STATUS_LINK_UP |
+ HV_M_STATUS_AUTONEG_COMPLETE |
+ HV_M_STATUS_SPEED_1000))
+ k1_enable = false;
+ }
+
+ /* Link stall fix for link up */
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19),
+ 0x0100);
+ if (ret_val)
+ goto release;
+
+ } else {
+ /* Link stall fix for link down */
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19),
+ 0x4100);
+ if (ret_val)
+ goto release;
+ }
+
+ ret_val = e1000_configure_k1_ich8lan(hw, k1_enable);
+
+release:
+ hw->phy.ops.release_phy(hw);
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_configure_k1_ich8lan - Configure K1 power state
+ * @hw: pointer to the HW structure
+ * @enable: K1 state to configure
+ *
+ * Configure the K1 power state based on the provided parameter.
+ * Assumes semaphore already acquired.
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ **/
+static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
+{
+ s32 ret_val = 0;
+ u32 ctrl_reg = 0;
+ u32 ctrl_ext = 0;
+ u32 reg = 0;
+ u16 kmrn_reg = 0;
+
+ ret_val = e1000e_read_kmrn_reg_locked(hw,
+ E1000_KMRNCTRLSTA_K1_CONFIG,
+ &kmrn_reg);
+ if (ret_val)
+ goto out;
+
+ if (k1_enable)
+ kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE;
+ else
+ kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE;
+
+ ret_val = e1000e_write_kmrn_reg_locked(hw,
+ E1000_KMRNCTRLSTA_K1_CONFIG,
+ kmrn_reg);
+ if (ret_val)
+ goto out;
+
+ udelay(20);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_reg = er32(CTRL);
+
+ reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ reg |= E1000_CTRL_FRCSPD;
+ ew32(CTRL, reg);
+
+ ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_SPD_BYPS);
+ udelay(20);
+ ew32(CTRL, ctrl_reg);
+ ew32(CTRL_EXT, ctrl_ext);
+ udelay(20);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_oem_bits_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ * @d0_state: boolean if entering d0 or d3 device state
+ *
+ * SW will configure Gbe Disable and LPLU based on the NVM. The four bits are
+ * collectively called OEM bits. The OEM Write Enable bit and SW Config bit
+ * in NVM determines whether HW should configure LPLU and Gbe Disable.
+ **/
+static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
+{
+ s32 ret_val = 0;
+ u32 mac_reg;
+ u16 oem_reg;
+
+ if (hw->mac.type != e1000_pchlan)
+ return ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ mac_reg = er32(EXTCNF_CTRL);
+ if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE)
+ goto out;
+
+ mac_reg = er32(FEXTNVM);
+ if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M))
+ goto out;
+
+ mac_reg = er32(PHY_CTRL);
+
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw, HV_OEM_BITS, &oem_reg);
+ if (ret_val)
+ goto out;
+
+ oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU);
+
+ if (d0_state) {
+ if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_D0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ } else {
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ }
+ /* Restart auto-neg to activate the bits */
+ if (!e1000_check_reset_block(hw))
+ oem_reg |= HV_OEM_BITS_RESTART_AN;
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, HV_OEM_BITS, oem_reg);
+
+out:
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+
+/**
* e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be
* done after every PHY reset.
**/
@@ -833,10 +1169,20 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
ret_val = hw->phy.ops.acquire_phy(hw);
if (ret_val)
return ret_val;
+
hw->phy.addr = 1;
- e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+ if (ret_val)
+ goto out;
hw->phy.ops.release_phy(hw);
+ /*
+ * Configure the K1 Si workaround during phy reset assuming there is
+ * link so that it disables K1 if link is in 1Gbps.
+ */
+ ret_val = e1000_k1_gig_workaround_hv(hw, true);
+
+out:
return ret_val;
}
@@ -882,11 +1228,8 @@ static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw)
**/
static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
{
- struct e1000_phy_info *phy = &hw->phy;
- u32 i;
- u32 data, cnf_size, cnf_base_addr, sw_cfg_mask;
- s32 ret_val;
- u16 reg, word_addr, reg_data, reg_addr, phy_page = 0;
+ s32 ret_val = 0;
+ u16 reg;
ret_val = e1000e_phy_hw_reset_generic(hw);
if (ret_val)
@@ -905,81 +1248,16 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
if (hw->mac.type == e1000_pchlan)
e1e_rphy(hw, BM_WUC, &reg);
- /*
- * Initialize the PHY from the NVM on ICH platforms. This
- * is needed due to an issue where the NVM configuration is
- * not properly autoloaded after power transitions.
- * Therefore, after each PHY reset, we will load the
- * configuration data out of the NVM manually.
- */
- if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) {
- struct e1000_adapter *adapter = hw->adapter;
-
- /* Check if SW needs configure the PHY */
- if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
- (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M))
- sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
- else
- sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
-
- data = er32(FEXTNVM);
- if (!(data & sw_cfg_mask))
- return 0;
-
- /* Wait for basic configuration completes before proceeding */
- e1000_lan_init_done_ich8lan(hw);
-
- /*
- * Make sure HW does not configure LCD from PHY
- * extended configuration before SW configuration
- */
- data = er32(EXTCNF_CTRL);
- if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
- return 0;
-
- cnf_size = er32(EXTCNF_SIZE);
- cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
- cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
- if (!cnf_size)
- return 0;
-
- cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
- cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
-
- /* Configure LCD from extended configuration region. */
-
- /* cnf_base_addr is in DWORD */
- word_addr = (u16)(cnf_base_addr << 1);
-
- for (i = 0; i < cnf_size; i++) {
- ret_val = e1000_read_nvm(hw,
- (word_addr + i * 2),
- 1,
- &reg_data);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_nvm(hw,
- (word_addr + i * 2 + 1),
- 1,
- &reg_addr);
- if (ret_val)
- return ret_val;
-
- /* Save off the PHY page for future writes. */
- if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
- phy_page = reg_data;
- continue;
- }
-
- reg_addr |= phy_page;
+ /* Configure the LCD with the extended configuration region in NVM */
+ ret_val = e1000_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
- ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data);
- if (ret_val)
- return ret_val;
- }
- }
+ /* Configure the LCD with the OEM bits in NVM */
+ if (hw->mac.type == e1000_pchlan)
+ ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+out:
return 0;
}
@@ -2306,6 +2584,7 @@ static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw)
**/
static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
{
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
u16 reg;
u32 ctrl, icr, kab;
s32 ret_val;
@@ -2341,6 +2620,18 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
ew32(PBS, E1000_PBS_16K);
}
+ if (hw->mac.type == e1000_pchlan) {
+ /* Save the NVM K1 bit setting*/
+ ret_val = e1000_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, &reg);
+ if (ret_val)
+ return ret_val;
+
+ if (reg & E1000_NVM_K1_ENABLE)
+ dev_spec->nvm_k1_enabled = true;
+ else
+ dev_spec->nvm_k1_enabled = false;
+ }
+
ctrl = er32(CTRL);
if (!e1000_check_reset_block(hw)) {
@@ -2386,6 +2677,15 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
if (hw->mac.type == e1000_pchlan)
e1e_rphy(hw, BM_WUC, &reg);
+ ret_val = e1000_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
+
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+ if (ret_val)
+ goto out;
+ }
/*
* For PCH, this write will make sure that any noise
* will be detected as a CRC error and be dropped rather than show up
@@ -2404,6 +2704,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
if (hw->mac.type == e1000_pchlan)
ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
+out:
return ret_val;
}
@@ -2708,14 +3009,6 @@ static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed,
if (ret_val)
return ret_val;
- if ((hw->mac.type == e1000_pchlan) && (*speed == SPEED_1000)) {
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_K1_CONFIG,
- E1000_KMRNCTRLSTA_K1_DISABLE);
- if (ret_val)
- return ret_val;
- }
-
if ((hw->mac.type == e1000_ich8lan) &&
(hw->phy.type == e1000_phy_igp_3) &&
(*speed == SPEED_1000)) {
@@ -3266,6 +3559,7 @@ struct e1000_info e1000_pch_info = {
| FLAG_HAS_AMT
| FLAG_HAS_FLASH
| FLAG_HAS_JUMBO_FRAMES
+ | FLAG_DISABLE_FC_PAUSE_TIME /* errata */
| FLAG_APME_IN_WUC,
.pba = 26,
.max_hw_frame_size = 4096,
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 0687c6aa4e46..fad8f9ea0043 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -2769,25 +2769,38 @@ void e1000e_reset(struct e1000_adapter *adapter)
/*
* flow control settings
*
- * The high water mark must be low enough to fit two full frame
+ * The high water mark must be low enough to fit one full frame
* (or the size used for early receive) above it in the Rx FIFO.
* Set it to the lower of:
* - 90% of the Rx FIFO size, and
* - the full Rx FIFO size minus the early receive size (for parts
* with ERT support assuming ERT set to E1000_ERT_2048), or
- * - the full Rx FIFO size minus two full frames
+ * - the full Rx FIFO size minus one full frame
*/
- if ((adapter->flags & FLAG_HAS_ERT) &&
- (adapter->netdev->mtu > ETH_DATA_LEN))
- hwm = min(((pba << 10) * 9 / 10),
- ((pba << 10) - (E1000_ERT_2048 << 3)));
- else
- hwm = min(((pba << 10) * 9 / 10),
- ((pba << 10) - (2 * adapter->max_frame_size)));
+ if (hw->mac.type == e1000_pchlan) {
+ /*
+ * Workaround PCH LOM adapter hangs with certain network
+ * loads. If hangs persist, try disabling Tx flow control.
+ */
+ if (adapter->netdev->mtu > ETH_DATA_LEN) {
+ fc->high_water = 0x3500;
+ fc->low_water = 0x1500;
+ } else {
+ fc->high_water = 0x5000;
+ fc->low_water = 0x3000;
+ }
+ } else {
+ if ((adapter->flags & FLAG_HAS_ERT) &&
+ (adapter->netdev->mtu > ETH_DATA_LEN))
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - (E1000_ERT_2048 << 3)));
+ else
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - adapter->max_frame_size));
- fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
- fc->low_water = (fc->high_water - (2 * adapter->max_frame_size));
- fc->low_water &= E1000_FCRTL_RTL; /* 8-byte granularity */
+ fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
+ fc->low_water = fc->high_water - 8;
+ }
if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
fc->pause_time = 0xFFFF;
@@ -2813,6 +2826,10 @@ void e1000e_reset(struct e1000_adapter *adapter)
if (mac->ops.init_hw(hw))
e_err("Hardware Error\n");
+ /* additional part of the flow-control workaround above */
+ if (hw->mac.type == e1000_pchlan)
+ ew32(FCRTV_PCH, 0x1000);
+
e1000_update_mng_vlan(adapter);
/* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
@@ -3610,7 +3627,7 @@ static void e1000_watchdog_task(struct work_struct *work)
case SPEED_100:
txb2b = 0;
netdev->tx_queue_len = 100;
- /* maybe add some timeout factor ? */
+ adapter->tx_timeout_factor = 10;
break;
}
@@ -4288,8 +4305,10 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
msleep(1);
- /* e1000e_down has a dependency on max_frame_size */
+ /* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */
adapter->max_frame_size = max_frame;
+ e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
+ netdev->mtu = new_mtu;
if (netif_running(netdev))
e1000e_down(adapter);
@@ -4319,9 +4338,6 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN
+ ETH_FCS_LEN;
- e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
- netdev->mtu = new_mtu;
-
if (netif_running(netdev))
e1000e_up(adapter);
else
diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index f9d33ab05e97..85f955f70417 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -71,7 +71,6 @@ static const u16 e1000_igp_2_cable_length_table[] =
#define I82577_CFG_ASSERT_CRS_ON_TX (1 << 15)
#define I82577_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift 100/10 */
#define I82577_CTRL_REG 23
-#define I82577_CTRL_DOWNSHIFT_MASK (7 << 10)
/* 82577 specific PHY registers */
#define I82577_PHY_CTRL_2 18
@@ -95,13 +94,6 @@ static const u16 e1000_igp_2_cable_length_table[] =
/* BM PHY Copper Specific Control 1 */
#define BM_CS_CTRL1 16
-/* BM PHY Copper Specific Status */
-#define BM_CS_STATUS 17
-#define BM_CS_STATUS_LINK_UP 0x0400
-#define BM_CS_STATUS_RESOLVED 0x0800
-#define BM_CS_STATUS_SPEED_MASK 0xC000
-#define BM_CS_STATUS_SPEED_1000 0x8000
-
#define HV_MUX_DATA_CTRL PHY_REG(776, 16)
#define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400
#define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004
@@ -563,7 +555,7 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
}
/**
- * e1000_read_kmrn_reg_locked - Read kumeran register
+ * e1000e_read_kmrn_reg_locked - Read kumeran register
* @hw: pointer to the HW structure
* @offset: register offset to be read
* @data: pointer to the read data
@@ -572,7 +564,7 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
* information retrieved is stored in data.
* Assumes semaphore already acquired.
**/
-s32 e1000_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
{
return __e1000_read_kmrn_reg(hw, offset, data, true);
}
@@ -631,7 +623,7 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
}
/**
- * e1000_write_kmrn_reg_locked - Write kumeran register
+ * e1000e_write_kmrn_reg_locked - Write kumeran register
* @hw: pointer to the HW structure
* @offset: register offset to write to
* @data: data to write at register offset
@@ -639,7 +631,7 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
* Write the data to PHY register at the offset using the kumeran interface.
* Assumes semaphore already acquired.
**/
-s32 e1000_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
{
return __e1000_write_kmrn_reg(hw, offset, data, true);
}
@@ -667,15 +659,6 @@ s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
phy_data |= I82577_CFG_ENABLE_DOWNSHIFT;
ret_val = phy->ops.write_phy_reg(hw, I82577_CFG_REG, phy_data);
- if (ret_val)
- goto out;
-
- /* Set number of link attempts before downshift */
- ret_val = phy->ops.read_phy_reg(hw, I82577_CTRL_REG, &phy_data);
- if (ret_val)
- goto out;
- phy_data &= ~I82577_CTRL_DOWNSHIFT_MASK;
- ret_val = phy->ops.write_phy_reg(hw, I82577_CTRL_REG, phy_data);
out:
return ret_val;
@@ -2665,19 +2648,18 @@ static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
page = 0;
if (reg > MAX_PHY_MULTI_PAGE_REG) {
- if ((hw->phy.type != e1000_phy_82578) ||
- ((reg != I82578_ADDR_REG) &&
- (reg != I82578_ADDR_REG + 1))) {
- u32 phy_addr = hw->phy.addr;
+ u32 phy_addr = hw->phy.addr;
- hw->phy.addr = 1;
+ hw->phy.addr = 1;
- /* Page is shifted left, PHY expects (page x 32) */
- ret_val = e1000e_write_phy_reg_mdic(hw,
- IGP01E1000_PHY_PAGE_SELECT,
- (page << IGP_PAGE_SHIFT));
- hw->phy.addr = phy_addr;
- }
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (page << IGP_PAGE_SHIFT));
+ hw->phy.addr = phy_addr;
+
+ if (ret_val)
+ goto out;
}
ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
@@ -2685,7 +2667,7 @@ static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
out:
/* Revert to MDIO fast mode, if applicable */
if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
- ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+ ret_val |= e1000_set_mdio_slow_mode_hv(hw, false);
if (!locked)
hw->phy.ops.release_phy(hw);
@@ -2791,19 +2773,18 @@ static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
}
if (reg > MAX_PHY_MULTI_PAGE_REG) {
- if ((hw->phy.type != e1000_phy_82578) ||
- ((reg != I82578_ADDR_REG) &&
- (reg != I82578_ADDR_REG + 1))) {
- u32 phy_addr = hw->phy.addr;
+ u32 phy_addr = hw->phy.addr;
- hw->phy.addr = 1;
+ hw->phy.addr = 1;
- /* Page is shifted left, PHY expects (page x 32) */
- ret_val = e1000e_write_phy_reg_mdic(hw,
- IGP01E1000_PHY_PAGE_SELECT,
- (page << IGP_PAGE_SHIFT));
- hw->phy.addr = phy_addr;
- }
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (page << IGP_PAGE_SHIFT));
+ hw->phy.addr = phy_addr;
+
+ if (ret_val)
+ goto out;
}
ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
@@ -2812,7 +2793,7 @@ static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
out:
/* Revert to MDIO fast mode, if applicable */
if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
- ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+ ret_val |= e1000_set_mdio_slow_mode_hv(hw, false);
if (!locked)
hw->phy.ops.release_phy(hw);
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-20 18:21:30 +0100