diff options
Diffstat (limited to 'drivers/net/ethernet/dlink/de620.h')
| -rw-r--r-- | drivers/net/ethernet/dlink/de620.h | 117 |
1 files changed, 117 insertions, 0 deletions
diff --git a/drivers/net/ethernet/dlink/de620.h b/drivers/net/ethernet/dlink/de620.h new file mode 100644 index 000000000000..e8d9a88f4cb5 --- /dev/null +++ b/drivers/net/ethernet/dlink/de620.h @@ -0,0 +1,117 @@ +/********************************************************* + * * + * Definition of D-Link DE-620 Ethernet Pocket adapter * + * * + *********************************************************/ + +/* DE-620's CMD port Command */ +#define CS0 0x08 /* 1->0 command strobe */ +#define ICEN 0x04 /* 0=enable DL3520 host interface */ +#define DS0 0x02 /* 1->0 data strobe 0 */ +#define DS1 0x01 /* 1->0 data strobe 1 */ + +#define WDIR 0x20 /* general 0=read 1=write */ +#define RDIR 0x00 /* (not 100% confirm ) */ +#define PS2WDIR 0x00 /* ps/2 mode 1=read, 0=write */ +#define PS2RDIR 0x20 + +#define IRQEN 0x10 /* 1 = enable printer IRQ line */ +#define SELECTIN 0x08 /* 1 = select printer */ +#define INITP 0x04 /* 0 = initial printer */ +#define AUTOFEED 0x02 /* 1 = printer auto form feed */ +#define STROBE 0x01 /* 0->1 data strobe */ + +#define RESET 0x08 +#define NIS0 0x20 /* 0 = BNC, 1 = UTP */ +#define NCTL0 0x10 + +/* DE-620 DIC Command */ +#define W_DUMMY 0x00 /* DIC reserved command */ +#define W_CR 0x20 /* DIC write command register */ +#define W_NPR 0x40 /* DIC write Next Page Register */ +#define W_TBR 0x60 /* DIC write Tx Byte Count 1 reg */ +#define W_RSA 0x80 /* DIC write Remote Start Addr 1 */ + +/* DE-620's STAT port bits 7-4 */ +#define EMPTY 0x80 /* 1 = receive buffer empty */ +#define INTLEVEL 0x40 /* 1 = interrupt level is high */ +#define TXBF1 0x20 /* 1 = transmit buffer 1 is in use */ +#define TXBF0 0x10 /* 1 = transmit buffer 0 is in use */ +#define READY 0x08 /* 1 = h/w ready to accept cmd/data */ + +/* IDC 1 Command */ +#define W_RSA1 0xa0 /* write remote start address 1 */ +#define W_RSA0 0xa1 /* write remote start address 0 */ +#define W_NPRF 0xa2 /* write next page register NPR15-NPR8 */ +#define W_DFR 0xa3 /* write delay factor register */ +#define W_CPR 0xa4 /* write current page register */ +#define W_SPR 0xa5 /* write start page register */ +#define W_EPR 0xa6 /* write end page register */ +#define W_SCR 0xa7 /* write system configuration register */ +#define W_TCR 0xa8 /* write Transceiver Configuration reg */ +#define W_EIP 0xa9 /* write EEPM Interface port */ +#define W_PAR0 0xaa /* write physical address register 0 */ +#define W_PAR1 0xab /* write physical address register 1 */ +#define W_PAR2 0xac /* write physical address register 2 */ +#define W_PAR3 0xad /* write physical address register 3 */ +#define W_PAR4 0xae /* write physical address register 4 */ +#define W_PAR5 0xaf /* write physical address register 5 */ + +/* IDC 2 Command */ +#define R_STS 0xc0 /* read status register */ +#define R_CPR 0xc1 /* read current page register */ +#define R_BPR 0xc2 /* read boundary page register */ +#define R_TDR 0xc3 /* read time domain reflectometry reg */ + +/* STATUS Register */ +#define EEDI 0x80 /* EEPM DO pin */ +#define TXSUC 0x40 /* tx success */ +#define T16 0x20 /* tx fail 16 times */ +#define TS1 0x40 /* 0=Tx success, 1=T16 */ +#define TS0 0x20 /* 0=Tx success, 1=T16 */ +#define RXGOOD 0x10 /* rx a good packet */ +#define RXCRC 0x08 /* rx a CRC error packet */ +#define RXSHORT 0x04 /* rx a short packet */ +#define COLS 0x02 /* coaxial collision status */ +#define LNKS 0x01 /* UTP link status */ + +/* Command Register */ +#define CLEAR 0x10 /* reset part of hardware */ +#define NOPER 0x08 /* No Operation */ +#define RNOP 0x08 +#define RRA 0x06 /* After RR then auto-advance NPR & BPR(=NPR-1) */ +#define RRN 0x04 /* Normal Remote Read mode */ +#define RW1 0x02 /* Remote Write tx buffer 1 ( page 6 - 11 ) */ +#define RW0 0x00 /* Remote Write tx buffer 0 ( page 0 - 5 ) */ +#define TXEN 0x01 /* 0->1 tx enable */ + +/* System Configuration Register */ +#define TESTON 0x80 /* test host data transfer reliability */ +#define SLEEP 0x40 /* sleep mode */ +#if 0 +#define FASTMODE 0x04 /* fast mode for intel 82360SL fast mode */ +#define BYTEMODE 0x02 /* byte mode */ +#else +#define FASTMODE 0x20 /* fast mode for intel 82360SL fast mode */ +#define BYTEMODE 0x10 /* byte mode */ +#endif +#define NIBBLEMODE 0x00 /* nibble mode */ +#define IRQINV 0x08 /* turn off IRQ line inverter */ +#define IRQNML 0x00 /* turn on IRQ line inverter */ +#define INTON 0x04 +#define AUTOFFSET 0x02 /* auto shift address to TPR+12 */ +#define AUTOTX 0x01 /* auto tx when leave RW mode */ + +/* Transceiver Configuration Register */ +#define JABBER 0x80 /* generate jabber condition */ +#define TXSUCINT 0x40 /* enable tx success interrupt */ +#define T16INT 0x20 /* enable T16 interrupt */ +#define RXERRPKT 0x10 /* accept CRC error or short packet */ +#define EXTERNALB2 0x0C /* external loopback 2 */ +#define EXTERNALB1 0x08 /* external loopback 1 */ +#define INTERNALB 0x04 /* internal loopback */ +#define NMLOPERATE 0x00 /* normal operation */ +#define RXPBM 0x03 /* rx physical, broadcast, multicast */ +#define RXPB 0x02 /* rx physical, broadcast */ +#define RXALL 0x01 /* rx all packet */ +#define RXOFF 0x00 /* rx disable */ |