diff options
Diffstat (limited to 'drivers/net/ethernet/smsc/smsc911x.c')
| -rw-r--r-- | drivers/net/ethernet/smsc/smsc911x.c | 61 |
1 files changed, 50 insertions, 11 deletions
diff --git a/drivers/net/ethernet/smsc/smsc911x.c b/drivers/net/ethernet/smsc/smsc911x.c index affb29da353e..77ed74561e5f 100644 --- a/drivers/net/ethernet/smsc/smsc911x.c +++ b/drivers/net/ethernet/smsc/smsc911x.c @@ -1342,6 +1342,42 @@ static void smsc911x_rx_multicast_update_workaround(struct smsc911x_data *pdata) spin_unlock(&pdata->mac_lock); } +static int smsc911x_phy_general_power_up(struct smsc911x_data *pdata) +{ + int rc = 0; + + if (!pdata->phy_dev) + return rc; + + /* If the internal PHY is in General Power-Down mode, all, except the + * management interface, is powered-down and stays in that condition as + * long as Phy register bit 0.11 is HIGH. + * + * In that case, clear the bit 0.11, so the PHY powers up and we can + * access to the phy registers. + */ + rc = phy_read(pdata->phy_dev, MII_BMCR); + if (rc < 0) { + SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); + return rc; + } + + /* If the PHY general power-down bit is not set is not necessary to + * disable the general power down-mode. + */ + if (rc & BMCR_PDOWN) { + rc = phy_write(pdata->phy_dev, MII_BMCR, rc & ~BMCR_PDOWN); + if (rc < 0) { + SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); + return rc; + } + + usleep_range(1000, 1500); + } + + return 0; +} + static int smsc911x_phy_disable_energy_detect(struct smsc911x_data *pdata) { int rc = 0; @@ -1356,12 +1392,8 @@ static int smsc911x_phy_disable_energy_detect(struct smsc911x_data *pdata) return rc; } - /* - * If energy is detected the PHY is already awake so is not necessary - * to disable the energy detect power-down mode. - */ - if ((rc & MII_LAN83C185_EDPWRDOWN) && - !(rc & MII_LAN83C185_ENERGYON)) { + /* Only disable if energy detect mode is already enabled */ + if (rc & MII_LAN83C185_EDPWRDOWN) { /* Disable energy detect mode for this SMSC Transceivers */ rc = phy_write(pdata->phy_dev, MII_LAN83C185_CTRL_STATUS, rc & (~MII_LAN83C185_EDPWRDOWN)); @@ -1370,8 +1402,8 @@ static int smsc911x_phy_disable_energy_detect(struct smsc911x_data *pdata) SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); return rc; } - - mdelay(1); + /* Allow PHY to wakeup */ + mdelay(2); } return 0; @@ -1393,7 +1425,6 @@ static int smsc911x_phy_enable_energy_detect(struct smsc911x_data *pdata) /* Only enable if energy detect mode is already disabled */ if (!(rc & MII_LAN83C185_EDPWRDOWN)) { - mdelay(100); /* Enable energy detect mode for this SMSC Transceivers */ rc = phy_write(pdata->phy_dev, MII_LAN83C185_CTRL_STATUS, rc | MII_LAN83C185_EDPWRDOWN); @@ -1402,8 +1433,6 @@ static int smsc911x_phy_enable_energy_detect(struct smsc911x_data *pdata) SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); return rc; } - - mdelay(1); } return 0; } @@ -1415,6 +1444,16 @@ static int smsc911x_soft_reset(struct smsc911x_data *pdata) int ret; /* + * Make sure to power-up the PHY chip before doing a reset, otherwise + * the reset fails. + */ + ret = smsc911x_phy_general_power_up(pdata); + if (ret) { + SMSC_WARN(pdata, drv, "Failed to power-up the PHY chip"); + return ret; + } + + /* * LAN9210/LAN9211/LAN9220/LAN9221 chips have an internal PHY that * are initialized in a Energy Detect Power-Down mode that prevents * the MAC chip to be software reseted. So we have to wakeup the PHY |