diff options
Diffstat (limited to 'drivers/net/phy/marvell.c')
| -rw-r--r-- | drivers/net/phy/marvell.c | 131 |
1 files changed, 124 insertions, 7 deletions
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c index f0574073a2a3..32a8503a7acd 100644 --- a/drivers/net/phy/marvell.c +++ b/drivers/net/phy/marvell.c @@ -58,9 +58,25 @@ #define MII_M1111_RX_DELAY 0x80 #define MII_M1111_TX_DELAY 0x2 #define MII_M1111_PHY_EXT_SR 0x1b -#define MII_M1111_HWCFG_MODE_MASK 0xf -#define MII_M1111_HWCFG_MODE_RGMII 0xb + +#define MII_M1111_HWCFG_MODE_MASK 0xf +#define MII_M1111_HWCFG_MODE_COPPER_RGMII 0xb +#define MII_M1111_HWCFG_MODE_FIBER_RGMII 0x3 #define MII_M1111_HWCFG_MODE_SGMII_NO_CLK 0x4 +#define MII_M1111_HWCFG_FIBER_COPPER_AUTO 0x8000 +#define MII_M1111_HWCFG_FIBER_COPPER_RES 0x2000 + +#define MII_M1111_COPPER 0 +#define MII_M1111_FIBER 1 + +#define MII_M1011_PHY_STATUS 0x11 +#define MII_M1011_PHY_STATUS_1000 0x8000 +#define MII_M1011_PHY_STATUS_100 0x4000 +#define MII_M1011_PHY_STATUS_SPD_MASK 0xc000 +#define MII_M1011_PHY_STATUS_FULLDUPLEX 0x2000 +#define MII_M1011_PHY_STATUS_RESOLVED 0x0800 +#define MII_M1011_PHY_STATUS_LINK 0x0400 + MODULE_DESCRIPTION("Marvell PHY driver"); MODULE_AUTHOR("Andy Fleming"); @@ -141,12 +157,22 @@ static int marvell_config_aneg(struct phy_device *phydev) static int m88e1111_config_init(struct phy_device *phydev) { int err; + int temp; + int mode; + + /* Enable Fiber/Copper auto selection */ + temp = phy_read(phydev, MII_M1111_PHY_EXT_SR); + temp |= MII_M1111_HWCFG_FIBER_COPPER_AUTO; + phy_write(phydev, MII_M1111_PHY_EXT_SR, temp); + + temp = phy_read(phydev, MII_BMCR); + temp |= BMCR_RESET; + phy_write(phydev, MII_BMCR, temp); if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) || (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) || (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) || (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) { - int temp; temp = phy_read(phydev, MII_M1111_PHY_EXT_CR); if (temp < 0) @@ -171,7 +197,13 @@ static int m88e1111_config_init(struct phy_device *phydev) return temp; temp &= ~(MII_M1111_HWCFG_MODE_MASK); - temp |= MII_M1111_HWCFG_MODE_RGMII; + + mode = phy_read(phydev, MII_M1111_PHY_EXT_CR); + + if (mode & MII_M1111_HWCFG_FIBER_COPPER_RES) + temp |= MII_M1111_HWCFG_MODE_FIBER_RGMII; + else + temp |= MII_M1111_HWCFG_MODE_COPPER_RGMII; err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp); if (err < 0) @@ -179,8 +211,6 @@ static int m88e1111_config_init(struct phy_device *phydev) } if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { - int temp; - temp = phy_read(phydev, MII_M1111_PHY_EXT_SR); if (temp < 0) return temp; @@ -262,6 +292,93 @@ static int m88e1145_config_init(struct phy_device *phydev) return 0; } +/* marvell_read_status + * + * Generic status code does not detect Fiber correctly! + * Description: + * Check the link, then figure out the current state + * by comparing what we advertise with what the link partner + * advertises. Start by checking the gigabit possibilities, + * then move on to 10/100. + */ +static int marvell_read_status(struct phy_device *phydev) +{ + int adv; + int err; + int lpa; + int status = 0; + + /* Update the link, but return if there + * was an error */ + err = genphy_update_link(phydev); + if (err) + return err; + + if (AUTONEG_ENABLE == phydev->autoneg) { + status = phy_read(phydev, MII_M1011_PHY_STATUS); + if (status < 0) + return status; + + lpa = phy_read(phydev, MII_LPA); + if (lpa < 0) + return lpa; + + adv = phy_read(phydev, MII_ADVERTISE); + if (adv < 0) + return adv; + + lpa &= adv; + + if (status & MII_M1011_PHY_STATUS_FULLDUPLEX) + phydev->duplex = DUPLEX_FULL; + else + phydev->duplex = DUPLEX_HALF; + + status = status & MII_M1011_PHY_STATUS_SPD_MASK; + phydev->pause = phydev->asym_pause = 0; + + switch (status) { + case MII_M1011_PHY_STATUS_1000: + phydev->speed = SPEED_1000; + break; + + case MII_M1011_PHY_STATUS_100: + phydev->speed = SPEED_100; + break; + + default: + phydev->speed = SPEED_10; + break; + } + + if (phydev->duplex == DUPLEX_FULL) { + phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0; + phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0; + } + } else { + int bmcr = phy_read(phydev, MII_BMCR); + + if (bmcr < 0) + return bmcr; + + if (bmcr & BMCR_FULLDPLX) + phydev->duplex = DUPLEX_FULL; + else + phydev->duplex = DUPLEX_HALF; + + if (bmcr & BMCR_SPEED1000) + phydev->speed = SPEED_1000; + else if (bmcr & BMCR_SPEED100) + phydev->speed = SPEED_100; + else + phydev->speed = SPEED_10; + + phydev->pause = phydev->asym_pause = 0; + } + + return 0; +} + static struct phy_driver marvell_drivers[] = { { .phy_id = 0x01410c60, @@ -296,7 +413,7 @@ static struct phy_driver marvell_drivers[] = { .flags = PHY_HAS_INTERRUPT, .config_init = &m88e1111_config_init, .config_aneg = &marvell_config_aneg, - .read_status = &genphy_read_status, + .read_status = &marvell_read_status, .ack_interrupt = &marvell_ack_interrupt, .config_intr = &marvell_config_intr, .driver = { .owner = THIS_MODULE }, |