diff options
Diffstat (limited to 'drivers/net/phy/motorcomm.c')
| -rw-r--r-- | drivers/net/phy/motorcomm.c | 559 |
1 files changed, 479 insertions, 80 deletions
diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c index 685190db72de..2fa5a90e073b 100644 --- a/drivers/net/phy/motorcomm.c +++ b/drivers/net/phy/motorcomm.c @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0+ /* - * Motorcomm 8511/8521/8531S PHY driver. + * Motorcomm 8511/8521/8531/8531S PHY driver. * * Author: Peter Geis <pgwipeout@gmail.com> * Author: Frank <Frank.Sae@motor-comm.com> @@ -10,10 +10,12 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/phy.h> +#include <linux/of.h> #define PHY_ID_YT8511 0x0000010a -#define PHY_ID_YT8521 0x0000011A -#define PHY_ID_YT8531S 0x4F51E91A +#define PHY_ID_YT8521 0x0000011a +#define PHY_ID_YT8531 0x4f51e91b +#define PHY_ID_YT8531S 0x4f51e91a /* YT8521/YT8531S Register Overview * UTP Register space | FIBER Register space @@ -161,6 +163,11 @@ #define YT8521_CHIP_CONFIG_REG 0xA001 #define YT8521_CCR_SW_RST BIT(15) +/* 1b0 disable 1.9ns rxc clock delay *default* + * 1b1 enable 1.9ns rxc clock delay + */ +#define YT8521_CCR_RXC_DLY_EN BIT(8) +#define YT8521_CCR_RXC_DLY_1_900_NS 1900 #define YT8521_CCR_MODE_SEL_MASK (BIT(2) | BIT(1) | BIT(0)) #define YT8521_CCR_MODE_UTP_TO_RGMII 0 @@ -178,22 +185,29 @@ #define YT8521_MODE_POLL 0x3 #define YT8521_RGMII_CONFIG1_REG 0xA003 - -/* TX Gig-E Delay is bits 3:0, default 0x1 - * TX Fast-E Delay is bits 7:4, default 0xf - * RX Delay is bits 13:10, default 0x0 - * Delay = 150ps * N - * On = 2250ps, off = 0ps +/* 1b0 use original tx_clk_rgmii *default* + * 1b1 use inverted tx_clk_rgmii. */ -#define YT8521_RC1R_RX_DELAY_MASK (0xF << 10) -#define YT8521_RC1R_RX_DELAY_EN (0xF << 10) -#define YT8521_RC1R_RX_DELAY_DIS (0x0 << 10) -#define YT8521_RC1R_FE_TX_DELAY_MASK (0xF << 4) -#define YT8521_RC1R_FE_TX_DELAY_EN (0xF << 4) -#define YT8521_RC1R_FE_TX_DELAY_DIS (0x0 << 4) -#define YT8521_RC1R_GE_TX_DELAY_MASK (0xF << 0) -#define YT8521_RC1R_GE_TX_DELAY_EN (0xF << 0) -#define YT8521_RC1R_GE_TX_DELAY_DIS (0x0 << 0) +#define YT8521_RC1R_TX_CLK_SEL_INVERTED BIT(14) +#define YT8521_RC1R_RX_DELAY_MASK GENMASK(13, 10) +#define YT8521_RC1R_FE_TX_DELAY_MASK GENMASK(7, 4) +#define YT8521_RC1R_GE_TX_DELAY_MASK GENMASK(3, 0) +#define YT8521_RC1R_RGMII_0_000_NS 0 +#define YT8521_RC1R_RGMII_0_150_NS 1 +#define YT8521_RC1R_RGMII_0_300_NS 2 +#define YT8521_RC1R_RGMII_0_450_NS 3 +#define YT8521_RC1R_RGMII_0_600_NS 4 +#define YT8521_RC1R_RGMII_0_750_NS 5 +#define YT8521_RC1R_RGMII_0_900_NS 6 +#define YT8521_RC1R_RGMII_1_050_NS 7 +#define YT8521_RC1R_RGMII_1_200_NS 8 +#define YT8521_RC1R_RGMII_1_350_NS 9 +#define YT8521_RC1R_RGMII_1_500_NS 10 +#define YT8521_RC1R_RGMII_1_650_NS 11 +#define YT8521_RC1R_RGMII_1_800_NS 12 +#define YT8521_RC1R_RGMII_1_950_NS 13 +#define YT8521_RC1R_RGMII_2_100_NS 14 +#define YT8521_RC1R_RGMII_2_250_NS 15 #define YTPHY_MISC_CONFIG_REG 0xA006 #define YTPHY_MCR_FIBER_SPEED_MASK BIT(0) @@ -222,11 +236,36 @@ */ #define YTPHY_WCR_TYPE_PULSE BIT(0) -#define YT8531S_SYNCE_CFG_REG 0xA012 -#define YT8531S_SCR_SYNCE_ENABLE BIT(6) +#define YTPHY_SYNCE_CFG_REG 0xA012 +#define YT8521_SCR_SYNCE_ENABLE BIT(5) +/* 1b0 output 25m clock + * 1b1 output 125m clock *default* + */ +#define YT8521_SCR_CLK_FRE_SEL_125M BIT(3) +#define YT8521_SCR_CLK_SRC_MASK GENMASK(2, 1) +#define YT8521_SCR_CLK_SRC_PLL_125M 0 +#define YT8521_SCR_CLK_SRC_UTP_RX 1 +#define YT8521_SCR_CLK_SRC_SDS_RX 2 +#define YT8521_SCR_CLK_SRC_REF_25M 3 +#define YT8531_SCR_SYNCE_ENABLE BIT(6) +/* 1b0 output 25m clock *default* + * 1b1 output 125m clock + */ +#define YT8531_SCR_CLK_FRE_SEL_125M BIT(4) +#define YT8531_SCR_CLK_SRC_MASK GENMASK(3, 1) +#define YT8531_SCR_CLK_SRC_PLL_125M 0 +#define YT8531_SCR_CLK_SRC_UTP_RX 1 +#define YT8531_SCR_CLK_SRC_SDS_RX 2 +#define YT8531_SCR_CLK_SRC_CLOCK_FROM_DIGITAL 3 +#define YT8531_SCR_CLK_SRC_REF_25M 4 +#define YT8531_SCR_CLK_SRC_SSC_25M 5 /* Extended Register end */ +#define YTPHY_DTS_OUTPUT_CLK_DIS 0 +#define YTPHY_DTS_OUTPUT_CLK_25M 25000000 +#define YTPHY_DTS_OUTPUT_CLK_125M 125000000 + struct yt8521_priv { /* combo_advertising is used for case of YT8521 in combo mode, * this means that yt8521 may work in utp or fiber mode which depends @@ -479,6 +518,61 @@ err_restore_page: return phy_restore_page(phydev, old_page, ret); } +static int yt8531_set_wol(struct phy_device *phydev, + struct ethtool_wolinfo *wol) +{ + const u16 mac_addr_reg[] = { + YTPHY_WOL_MACADDR2_REG, + YTPHY_WOL_MACADDR1_REG, + YTPHY_WOL_MACADDR0_REG, + }; + const u8 *mac_addr; + u16 mask, val; + int ret; + u8 i; + + if (wol->wolopts & WAKE_MAGIC) { + mac_addr = phydev->attached_dev->dev_addr; + + /* Store the device address for the magic packet */ + for (i = 0; i < 3; i++) { + ret = ytphy_write_ext_with_lock(phydev, mac_addr_reg[i], + ((mac_addr[i * 2] << 8)) | + (mac_addr[i * 2 + 1])); + if (ret < 0) + return ret; + } + + /* Enable WOL feature */ + mask = YTPHY_WCR_PULSE_WIDTH_MASK | YTPHY_WCR_INTR_SEL; + val = YTPHY_WCR_ENABLE | YTPHY_WCR_INTR_SEL; + val |= YTPHY_WCR_TYPE_PULSE | YTPHY_WCR_PULSE_WIDTH_672MS; + ret = ytphy_modify_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG, + mask, val); + if (ret < 0) + return ret; + + /* Enable WOL interrupt */ + ret = phy_modify(phydev, YTPHY_INTERRUPT_ENABLE_REG, 0, + YTPHY_IER_WOL); + if (ret < 0) + return ret; + } else { + /* Disable WOL feature */ + mask = YTPHY_WCR_ENABLE | YTPHY_WCR_INTR_SEL; + ret = ytphy_modify_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG, + mask, 0); + + /* Disable WOL interrupt */ + ret = phy_modify(phydev, YTPHY_INTERRUPT_ENABLE_REG, + YTPHY_IER_WOL, 0); + if (ret < 0) + return ret; + } + + return 0; +} + static int yt8511_read_page(struct phy_device *phydev) { return __phy_read(phydev, YT8511_PAGE_SELECT); @@ -594,6 +688,153 @@ static int yt8521_write_page(struct phy_device *phydev, int page) }; /** + * struct ytphy_cfg_reg_map - map a config value to a register value + * @cfg: value in device configuration + * @reg: value in the register + */ +struct ytphy_cfg_reg_map { + u32 cfg; + u32 reg; +}; + +static const struct ytphy_cfg_reg_map ytphy_rgmii_delays[] = { + /* for tx delay / rx delay with YT8521_CCR_RXC_DLY_EN is not set. */ + { 0, YT8521_RC1R_RGMII_0_000_NS }, + { 150, YT8521_RC1R_RGMII_0_150_NS }, + { 300, YT8521_RC1R_RGMII_0_300_NS }, + { 450, YT8521_RC1R_RGMII_0_450_NS }, + { 600, YT8521_RC1R_RGMII_0_600_NS }, + { 750, YT8521_RC1R_RGMII_0_750_NS }, + { 900, YT8521_RC1R_RGMII_0_900_NS }, + { 1050, YT8521_RC1R_RGMII_1_050_NS }, + { 1200, YT8521_RC1R_RGMII_1_200_NS }, + { 1350, YT8521_RC1R_RGMII_1_350_NS }, + { 1500, YT8521_RC1R_RGMII_1_500_NS }, + { 1650, YT8521_RC1R_RGMII_1_650_NS }, + { 1800, YT8521_RC1R_RGMII_1_800_NS }, + { 1950, YT8521_RC1R_RGMII_1_950_NS }, /* default tx/rx delay */ + { 2100, YT8521_RC1R_RGMII_2_100_NS }, + { 2250, YT8521_RC1R_RGMII_2_250_NS }, + + /* only for rx delay with YT8521_CCR_RXC_DLY_EN is set. */ + { 0 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_000_NS }, + { 150 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_150_NS }, + { 300 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_300_NS }, + { 450 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_450_NS }, + { 600 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_600_NS }, + { 750 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_750_NS }, + { 900 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_900_NS }, + { 1050 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_050_NS }, + { 1200 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_200_NS }, + { 1350 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_350_NS }, + { 1500 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_500_NS }, + { 1650 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_650_NS }, + { 1800 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_800_NS }, + { 1950 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_950_NS }, + { 2100 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_2_100_NS }, + { 2250 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_2_250_NS } +}; + +static u32 ytphy_get_delay_reg_value(struct phy_device *phydev, + const char *prop_name, + const struct ytphy_cfg_reg_map *tbl, + int tb_size, + u16 *rxc_dly_en, + u32 dflt) +{ + struct device_node *node = phydev->mdio.dev.of_node; + int tb_size_half = tb_size / 2; + u32 val; + int i; + + if (of_property_read_u32(node, prop_name, &val)) + goto err_dts_val; + + /* when rxc_dly_en is NULL, it is get the delay for tx, only half of + * tb_size is valid. + */ + if (!rxc_dly_en) + tb_size = tb_size_half; + + for (i = 0; i < tb_size; i++) { + if (tbl[i].cfg == val) { + if (rxc_dly_en && i < tb_size_half) + *rxc_dly_en = 0; + return tbl[i].reg; + } + } + + phydev_warn(phydev, "Unsupported value %d for %s using default (%u)\n", + val, prop_name, dflt); + +err_dts_val: + /* when rxc_dly_en is not NULL, it is get the delay for rx. + * The rx default in dts and ytphy_rgmii_clk_delay_config is 1950 ps, + * so YT8521_CCR_RXC_DLY_EN should not be set. + */ + if (rxc_dly_en) + *rxc_dly_en = 0; + + return dflt; +} + +static int ytphy_rgmii_clk_delay_config(struct phy_device *phydev) +{ + int tb_size = ARRAY_SIZE(ytphy_rgmii_delays); + u16 rxc_dly_en = YT8521_CCR_RXC_DLY_EN; + u32 rx_reg, tx_reg; + u16 mask, val = 0; + int ret; + + rx_reg = ytphy_get_delay_reg_value(phydev, "rx-internal-delay-ps", + ytphy_rgmii_delays, tb_size, + &rxc_dly_en, + YT8521_RC1R_RGMII_1_950_NS); + tx_reg = ytphy_get_delay_reg_value(phydev, "tx-internal-delay-ps", + ytphy_rgmii_delays, tb_size, NULL, + YT8521_RC1R_RGMII_1_950_NS); + + switch (phydev->interface) { + case PHY_INTERFACE_MODE_RGMII: + rxc_dly_en = 0; + break; + case PHY_INTERFACE_MODE_RGMII_RXID: + val |= FIELD_PREP(YT8521_RC1R_RX_DELAY_MASK, rx_reg); + break; + case PHY_INTERFACE_MODE_RGMII_TXID: + rxc_dly_en = 0; + val |= FIELD_PREP(YT8521_RC1R_GE_TX_DELAY_MASK, tx_reg); + break; + case PHY_INTERFACE_MODE_RGMII_ID: + val |= FIELD_PREP(YT8521_RC1R_RX_DELAY_MASK, rx_reg) | + FIELD_PREP(YT8521_RC1R_GE_TX_DELAY_MASK, tx_reg); + break; + default: /* do not support other modes */ + return -EOPNOTSUPP; + } + + ret = ytphy_modify_ext(phydev, YT8521_CHIP_CONFIG_REG, + YT8521_CCR_RXC_DLY_EN, rxc_dly_en); + if (ret < 0) + return ret; + + /* Generally, it is not necessary to adjust YT8521_RC1R_FE_TX_DELAY */ + mask = YT8521_RC1R_RX_DELAY_MASK | YT8521_RC1R_GE_TX_DELAY_MASK; + return ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG, mask, val); +} + +static int ytphy_rgmii_clk_delay_config_with_lock(struct phy_device *phydev) +{ + int ret; + + phy_lock_mdio_bus(phydev); + ret = ytphy_rgmii_clk_delay_config(phydev); + phy_unlock_mdio_bus(phydev); + + return ret; +} + +/** * yt8521_probe() - read chip config then set suitable polling_mode * @phydev: a pointer to a &struct phy_device * @@ -601,9 +842,12 @@ static int yt8521_write_page(struct phy_device *phydev, int page) */ static int yt8521_probe(struct phy_device *phydev) { + struct device_node *node = phydev->mdio.dev.of_node; struct device *dev = &phydev->mdio.dev; struct yt8521_priv *priv; int chip_config; + u16 mask, val; + u32 freq; int ret; priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); @@ -648,27 +892,107 @@ static int yt8521_probe(struct phy_device *phydev) return ret; } - return 0; + if (of_property_read_u32(node, "motorcomm,clk-out-frequency-hz", &freq)) + freq = YTPHY_DTS_OUTPUT_CLK_DIS; + + if (phydev->drv->phy_id == PHY_ID_YT8521) { + switch (freq) { + case YTPHY_DTS_OUTPUT_CLK_DIS: + mask = YT8521_SCR_SYNCE_ENABLE; + val = 0; + break; + case YTPHY_DTS_OUTPUT_CLK_25M: + mask = YT8521_SCR_SYNCE_ENABLE | + YT8521_SCR_CLK_SRC_MASK | + YT8521_SCR_CLK_FRE_SEL_125M; + val = YT8521_SCR_SYNCE_ENABLE | + FIELD_PREP(YT8521_SCR_CLK_SRC_MASK, + YT8521_SCR_CLK_SRC_REF_25M); + break; + case YTPHY_DTS_OUTPUT_CLK_125M: + mask = YT8521_SCR_SYNCE_ENABLE | + YT8521_SCR_CLK_SRC_MASK | + YT8521_SCR_CLK_FRE_SEL_125M; + val = YT8521_SCR_SYNCE_ENABLE | + YT8521_SCR_CLK_FRE_SEL_125M | + FIELD_PREP(YT8521_SCR_CLK_SRC_MASK, + YT8521_SCR_CLK_SRC_PLL_125M); + break; + default: + phydev_warn(phydev, "Freq err:%u\n", freq); + return -EINVAL; + } + } else if (phydev->drv->phy_id == PHY_ID_YT8531S) { + switch (freq) { + case YTPHY_DTS_OUTPUT_CLK_DIS: + mask = YT8531_SCR_SYNCE_ENABLE; + val = 0; + break; + case YTPHY_DTS_OUTPUT_CLK_25M: + mask = YT8531_SCR_SYNCE_ENABLE | + YT8531_SCR_CLK_SRC_MASK | + YT8531_SCR_CLK_FRE_SEL_125M; + val = YT8531_SCR_SYNCE_ENABLE | + FIELD_PREP(YT8531_SCR_CLK_SRC_MASK, + YT8531_SCR_CLK_SRC_REF_25M); + break; + case YTPHY_DTS_OUTPUT_CLK_125M: + mask = YT8531_SCR_SYNCE_ENABLE | + YT8531_SCR_CLK_SRC_MASK | + YT8531_SCR_CLK_FRE_SEL_125M; + val = YT8531_SCR_SYNCE_ENABLE | + YT8531_SCR_CLK_FRE_SEL_125M | + FIELD_PREP(YT8531_SCR_CLK_SRC_MASK, + YT8531_SCR_CLK_SRC_PLL_125M); + break; + default: + phydev_warn(phydev, "Freq err:%u\n", freq); + return -EINVAL; + } + } else { + phydev_warn(phydev, "PHY id err\n"); + return -EINVAL; + } + + return ytphy_modify_ext_with_lock(phydev, YTPHY_SYNCE_CFG_REG, mask, + val); } -/** - * yt8531s_probe() - read chip config then set suitable polling_mode - * @phydev: a pointer to a &struct phy_device - * - * returns 0 or negative errno code - */ -static int yt8531s_probe(struct phy_device *phydev) +static int yt8531_probe(struct phy_device *phydev) { - int ret; + struct device_node *node = phydev->mdio.dev.of_node; + u16 mask, val; + u32 freq; - /* Disable SyncE clock output by default */ - ret = ytphy_modify_ext_with_lock(phydev, YT8531S_SYNCE_CFG_REG, - YT8531S_SCR_SYNCE_ENABLE, 0); - if (ret < 0) - return ret; + if (of_property_read_u32(node, "motorcomm,clk-out-frequency-hz", &freq)) + freq = YTPHY_DTS_OUTPUT_CLK_DIS; + + switch (freq) { + case YTPHY_DTS_OUTPUT_CLK_DIS: + mask = YT8531_SCR_SYNCE_ENABLE; + val = 0; + break; + case YTPHY_DTS_OUTPUT_CLK_25M: + mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK | + YT8531_SCR_CLK_FRE_SEL_125M; + val = YT8531_SCR_SYNCE_ENABLE | + FIELD_PREP(YT8531_SCR_CLK_SRC_MASK, + YT8531_SCR_CLK_SRC_REF_25M); + break; + case YTPHY_DTS_OUTPUT_CLK_125M: + mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK | + YT8531_SCR_CLK_FRE_SEL_125M; + val = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_FRE_SEL_125M | + FIELD_PREP(YT8531_SCR_CLK_SRC_MASK, + YT8531_SCR_CLK_SRC_PLL_125M); + break; + default: + phydev_warn(phydev, "Freq err:%u\n", freq); + return -EINVAL; + } - /* same as yt8521_probe */ - return yt8521_probe(phydev); + return ytphy_modify_ext_with_lock(phydev, YTPHY_SYNCE_CFG_REG, mask, + val); } /** @@ -1133,65 +1457,128 @@ static int yt8521_resume(struct phy_device *phydev) */ static int yt8521_config_init(struct phy_device *phydev) { + struct device_node *node = phydev->mdio.dev.of_node; int old_page; int ret = 0; - u16 val; old_page = phy_select_page(phydev, YT8521_RSSR_UTP_SPACE); if (old_page < 0) goto err_restore_page; - switch (phydev->interface) { - case PHY_INTERFACE_MODE_RGMII: - val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_FE_TX_DELAY_DIS; - val |= YT8521_RC1R_RX_DELAY_DIS; - break; - case PHY_INTERFACE_MODE_RGMII_RXID: - val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_FE_TX_DELAY_DIS; - val |= YT8521_RC1R_RX_DELAY_EN; - break; - case PHY_INTERFACE_MODE_RGMII_TXID: - val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_FE_TX_DELAY_EN; - val |= YT8521_RC1R_RX_DELAY_DIS; - break; - case PHY_INTERFACE_MODE_RGMII_ID: - val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_FE_TX_DELAY_EN; - val |= YT8521_RC1R_RX_DELAY_EN; - break; - case PHY_INTERFACE_MODE_SGMII: - break; - default: /* do not support other modes */ - ret = -EOPNOTSUPP; - goto err_restore_page; - } - /* set rgmii delay mode */ if (phydev->interface != PHY_INTERFACE_MODE_SGMII) { - ret = ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG, - (YT8521_RC1R_RX_DELAY_MASK | - YT8521_RC1R_FE_TX_DELAY_MASK | - YT8521_RC1R_GE_TX_DELAY_MASK), - val); + ret = ytphy_rgmii_clk_delay_config(phydev); if (ret < 0) goto err_restore_page; } - /* disable auto sleep */ - ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG, - YT8521_ESC1R_SLEEP_SW, 0); - if (ret < 0) - goto err_restore_page; - - /* enable RXC clock when no wire plug */ - ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG, - YT8521_CGR_RX_CLK_EN, 0); - if (ret < 0) - goto err_restore_page; + if (of_property_read_bool(node, "motorcomm,auto-sleep-disabled")) { + /* disable auto sleep */ + ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG, + YT8521_ESC1R_SLEEP_SW, 0); + if (ret < 0) + goto err_restore_page; + } + if (of_property_read_bool(node, "motorcomm,keep-pll-enabled")) { + /* enable RXC clock when no wire plug */ + ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG, + YT8521_CGR_RX_CLK_EN, 0); + if (ret < 0) + goto err_restore_page; + } err_restore_page: return phy_restore_page(phydev, old_page, ret); } +static int yt8531_config_init(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + int ret; + + ret = ytphy_rgmii_clk_delay_config_with_lock(phydev); + if (ret < 0) + return ret; + + if (of_property_read_bool(node, "motorcomm,auto-sleep-disabled")) { + /* disable auto sleep */ + ret = ytphy_modify_ext_with_lock(phydev, + YT8521_EXTREG_SLEEP_CONTROL1_REG, + YT8521_ESC1R_SLEEP_SW, 0); + if (ret < 0) + return ret; + } + + if (of_property_read_bool(node, "motorcomm,keep-pll-enabled")) { + /* enable RXC clock when no wire plug */ + ret = ytphy_modify_ext_with_lock(phydev, + YT8521_CLOCK_GATING_REG, + YT8521_CGR_RX_CLK_EN, 0); + if (ret < 0) + return ret; + } + + return 0; +} + +/** + * yt8531_link_change_notify() - Adjust the tx clock direction according to + * the current speed and dts config. + * @phydev: a pointer to a &struct phy_device + * + * NOTE: This function is only used to adapt to VF2 with JH7110 SoC. Please + * keep "motorcomm,tx-clk-adj-enabled" not exist in dts when the soc is not + * JH7110. + */ +static void yt8531_link_change_notify(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + bool tx_clk_1000_inverted = false; + bool tx_clk_100_inverted = false; + bool tx_clk_10_inverted = false; + bool tx_clk_adj_enabled = false; + u16 val = 0; + int ret; + + if (of_property_read_bool(node, "motorcomm,tx-clk-adj-enabled")) + tx_clk_adj_enabled = true; + + if (!tx_clk_adj_enabled) + return; + + if (of_property_read_bool(node, "motorcomm,tx-clk-10-inverted")) + tx_clk_10_inverted = true; + if (of_property_read_bool(node, "motorcomm,tx-clk-100-inverted")) + tx_clk_100_inverted = true; + if (of_property_read_bool(node, "motorcomm,tx-clk-1000-inverted")) + tx_clk_1000_inverted = true; + + if (phydev->speed < 0) + return; + + switch (phydev->speed) { + case SPEED_1000: + if (tx_clk_1000_inverted) + val = YT8521_RC1R_TX_CLK_SEL_INVERTED; + break; + case SPEED_100: + if (tx_clk_100_inverted) + val = YT8521_RC1R_TX_CLK_SEL_INVERTED; + break; + case SPEED_10: + if (tx_clk_10_inverted) + val = YT8521_RC1R_TX_CLK_SEL_INVERTED; + break; + default: + return; + } + + ret = ytphy_modify_ext_with_lock(phydev, YT8521_RGMII_CONFIG1_REG, + YT8521_RC1R_TX_CLK_SEL_INVERTED, val); + if (ret < 0) + phydev_warn(phydev, "Modify TX_CLK_SEL err:%d\n", ret); +} + /** * yt8521_prepare_fiber_features() - A small helper function that setup * fiber's features. @@ -1775,10 +2162,21 @@ static struct phy_driver motorcomm_phy_drvs[] = { .resume = yt8521_resume, }, { + PHY_ID_MATCH_EXACT(PHY_ID_YT8531), + .name = "YT8531 Gigabit Ethernet", + .probe = yt8531_probe, + .config_init = yt8531_config_init, + .suspend = genphy_suspend, + .resume = genphy_resume, + .get_wol = ytphy_get_wol, + .set_wol = yt8531_set_wol, + .link_change_notify = yt8531_link_change_notify, + }, + { PHY_ID_MATCH_EXACT(PHY_ID_YT8531S), .name = "YT8531S Gigabit Ethernet", .get_features = yt8521_get_features, - .probe = yt8531s_probe, + .probe = yt8521_probe, .read_page = yt8521_read_page, .write_page = yt8521_write_page, .get_wol = ytphy_get_wol, @@ -1795,7 +2193,7 @@ static struct phy_driver motorcomm_phy_drvs[] = { module_phy_driver(motorcomm_phy_drvs); -MODULE_DESCRIPTION("Motorcomm 8511/8521/8531S PHY driver"); +MODULE_DESCRIPTION("Motorcomm 8511/8521/8531/8531S PHY driver"); MODULE_AUTHOR("Peter Geis"); MODULE_AUTHOR("Frank"); MODULE_LICENSE("GPL"); @@ -1803,8 +2201,9 @@ MODULE_LICENSE("GPL"); static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = { { PHY_ID_MATCH_EXACT(PHY_ID_YT8511) }, { PHY_ID_MATCH_EXACT(PHY_ID_YT8521) }, + { PHY_ID_MATCH_EXACT(PHY_ID_YT8531) }, { PHY_ID_MATCH_EXACT(PHY_ID_YT8531S) }, - { /* sentinal */ } + { /* sentinel */ } }; MODULE_DEVICE_TABLE(mdio, motorcomm_tbl); |