diff options
Diffstat (limited to 'drivers/net/sky2.c')
-rw-r--r-- | drivers/net/sky2.c | 217 |
1 files changed, 171 insertions, 46 deletions
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index f8b973a04b65..bfeba5b9cd7a 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -23,12 +23,6 @@ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ -/* - * TOTEST - * - speed setting - * - suspend/resume - */ - #include <linux/config.h> #include <linux/crc32.h> #include <linux/kernel.h> @@ -57,7 +51,7 @@ #include "sky2.h" #define DRV_NAME "sky2" -#define DRV_VERSION "0.13" +#define DRV_VERSION "0.15" #define PFX DRV_NAME " " /* @@ -102,6 +96,10 @@ static int copybreak __read_mostly = 256; module_param(copybreak, int, 0); MODULE_PARM_DESC(copybreak, "Receive copy threshold"); +static int disable_msi = 0; +module_param(disable_msi, int, 0); +MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)"); + static const struct pci_device_id sky2_id_table[] = { { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, @@ -198,7 +196,7 @@ static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state) sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_PMC, &power_control); - vaux = (sky2_read8(hw, B0_CTST) & Y2_VAUX_AVAIL) && + vaux = (sky2_read16(hw, B0_CTST) & Y2_VAUX_AVAIL) && (power_control & PCI_PM_CAP_PME_D3cold); pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_CTRL, &power_control); @@ -522,10 +520,16 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) switch (sky2->speed) { case SPEED_1000: + reg &= ~GM_GPCR_SPEED_100; reg |= GM_GPCR_SPEED_1000; - /* fallthru */ + break; case SPEED_100: + reg &= ~GM_GPCR_SPEED_1000; reg |= GM_GPCR_SPEED_100; + break; + case SPEED_10: + reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100); + break; } if (sky2->duplex == DUPLEX_FULL) @@ -1448,6 +1452,29 @@ static void sky2_link_up(struct sky2_port *sky2) sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK); reg = gma_read16(hw, port, GM_GP_CTRL); + if (sky2->autoneg == AUTONEG_DISABLE) { + reg |= GM_GPCR_AU_ALL_DIS; + + /* Is write/read necessary? Copied from sky2_mac_init */ + gma_write16(hw, port, GM_GP_CTRL, reg); + gma_read16(hw, port, GM_GP_CTRL); + + switch (sky2->speed) { + case SPEED_1000: + reg &= ~GM_GPCR_SPEED_100; + reg |= GM_GPCR_SPEED_1000; + break; + case SPEED_100: + reg &= ~GM_GPCR_SPEED_1000; + reg |= GM_GPCR_SPEED_100; + break; + case SPEED_10: + reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100); + break; + } + } else + reg &= ~GM_GPCR_AU_ALL_DIS; + if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE) reg |= GM_GPCR_DUP_FULL; @@ -1834,6 +1861,8 @@ static int sky2_poll(struct net_device *dev0, int *budget) u16 hwidx; u16 tx_done[2] = { TX_NO_STATUS, TX_NO_STATUS }; + sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ); + hwidx = sky2_read16(hw, STAT_PUT_IDX); BUG_ON(hwidx >= STATUS_RING_SIZE); rmb(); @@ -1913,12 +1942,10 @@ static int sky2_poll(struct net_device *dev0, int *budget) } exit_loop: - sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ); - sky2_tx_check(hw, 0, tx_done[0]); sky2_tx_check(hw, 1, tx_done[1]); - if (sky2_read16(hw, STAT_PUT_IDX) == hw->st_idx) { + if (likely(work_done < to_do)) { /* need to restart TX timer */ if (is_ec_a1(hw)) { sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP); @@ -2141,14 +2168,12 @@ static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk) static int sky2_reset(struct sky2_hw *hw) { - u32 ctst; u16 status; u8 t8, pmd_type; - int i; - - ctst = sky2_read32(hw, B0_CTST); + int i, err; sky2_write8(hw, B0_CTST, CS_RST_CLR); + hw->chip_id = sky2_read8(hw, B2_CHIP_ID); if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) { printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n", @@ -2156,12 +2181,6 @@ static int sky2_reset(struct sky2_hw *hw) return -EOPNOTSUPP; } - /* ring for status responses */ - hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES, - &hw->st_dma); - if (!hw->st_le) - return -ENOMEM; - /* disable ASF */ if (hw->chip_id <= CHIP_ID_YUKON_EC) { sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET); @@ -2173,19 +2192,24 @@ static int sky2_reset(struct sky2_hw *hw) sky2_write8(hw, B0_CTST, CS_RST_CLR); /* clear PCI errors, if any */ - pci_read_config_word(hw->pdev, PCI_STATUS, &status); + err = pci_read_config_word(hw->pdev, PCI_STATUS, &status); + if (err) + goto pci_err; + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); - pci_write_config_word(hw->pdev, PCI_STATUS, - status | PCI_STATUS_ERROR_BITS); + err = pci_write_config_word(hw->pdev, PCI_STATUS, + status | PCI_STATUS_ERROR_BITS); + if (err) + goto pci_err; sky2_write8(hw, B0_CTST, CS_MRST_CLR); /* clear any PEX errors */ - if (is_pciex(hw)) { - u16 lstat; - pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT, - 0xffffffffUL); - pci_read_config_word(hw->pdev, PEX_LNK_STAT, &lstat); + if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP)) { + err = pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT, + 0xffffffffUL); + if (err) + goto pci_err; } pmd_type = sky2_read8(hw, B2_PMD_TYP); @@ -2297,6 +2321,14 @@ static int sky2_reset(struct sky2_hw *hw) sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); return 0; + +pci_err: + /* This is to catch a BIOS bug workaround where + * mmconfig table doesn't have other buses. + */ + printk(KERN_ERR PFX "%s: can't access PCI config space\n", + pci_name(hw->pdev)); + return err; } static u32 sky2_supported_modes(const struct sky2_hw *hw) @@ -2551,19 +2583,24 @@ static struct net_device_stats *sky2_get_stats(struct net_device *dev) static int sky2_set_mac_address(struct net_device *dev, void *p) { struct sky2_port *sky2 = netdev_priv(dev); - struct sockaddr *addr = p; + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + const struct sockaddr *addr = p; if (!is_valid_ether_addr(addr->sa_data)) return -EADDRNOTAVAIL; memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN); - memcpy_toio(sky2->hw->regs + B2_MAC_1 + sky2->port * 8, + memcpy_toio(hw->regs + B2_MAC_1 + port * 8, dev->dev_addr, ETH_ALEN); - memcpy_toio(sky2->hw->regs + B2_MAC_2 + sky2->port * 8, + memcpy_toio(hw->regs + B2_MAC_2 + port * 8, dev->dev_addr, ETH_ALEN); - if (netif_running(dev)) - sky2_phy_reinit(sky2); + /* virtual address for data */ + gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr); + + /* physical address: used for pause frames */ + gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr); return 0; } @@ -2843,7 +2880,7 @@ static int sky2_set_coalesce(struct net_device *dev, if (ecmd->rx_coalesce_usecs_irq == 0) sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_STOP); else { - sky2_write32(hw, STAT_TX_TIMER_INI, + sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, ecmd->rx_coalesce_usecs_irq)); sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); } @@ -3055,6 +3092,61 @@ static void __devinit sky2_show_addr(struct net_device *dev) dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]); } +/* Handle software interrupt used during MSI test */ +static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id, + struct pt_regs *regs) +{ + struct sky2_hw *hw = dev_id; + u32 status = sky2_read32(hw, B0_Y2_SP_ISRC2); + + if (status == 0) + return IRQ_NONE; + + if (status & Y2_IS_IRQ_SW) { + sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); + hw->msi = 1; + } + sky2_write32(hw, B0_Y2_SP_ICR, 2); + + sky2_read32(hw, B0_IMSK); + return IRQ_HANDLED; +} + +/* Test interrupt path by forcing a a software IRQ */ +static int __devinit sky2_test_msi(struct sky2_hw *hw) +{ + struct pci_dev *pdev = hw->pdev; + int i, err; + + sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW); + + err = request_irq(pdev->irq, sky2_test_intr, SA_SHIRQ, DRV_NAME, hw); + if (err) { + printk(KERN_ERR PFX "%s: cannot assign irq %d\n", + pci_name(pdev), pdev->irq); + return err; + } + + sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ); + wmb(); + + for (i = 0; i < 10; i++) { + barrier(); + if (hw->msi) + goto found; + mdelay(1); + } + + err = -EOPNOTSUPP; + sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); + found: + sky2_write32(hw, B0_IMSK, 0); + + free_irq(pdev->irq, hw); + + return err; +} + static int __devinit sky2_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { @@ -3135,6 +3227,12 @@ static int __devinit sky2_probe(struct pci_dev *pdev, } hw->pm_cap = pm_cap; + /* ring for status responses */ + hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES, + &hw->st_dma); + if (!hw->st_le) + goto err_out_iounmap; + err = sky2_reset(hw); if (err) goto err_out_iounmap; @@ -3169,7 +3267,22 @@ static int __devinit sky2_probe(struct pci_dev *pdev, } } - err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ, DRV_NAME, hw); + if (!disable_msi && pci_enable_msi(pdev) == 0) { + err = sky2_test_msi(hw); + if (err == -EOPNOTSUPP) { + /* MSI test failed, go back to INTx mode */ + printk(KERN_WARNING PFX "%s: No interrupt was generated using MSI, " + "switching to INTx mode. Please report this failure to " + "the PCI maintainer and include system chipset information.\n", + pci_name(pdev)); + pci_disable_msi(pdev); + } + else if (err) + goto err_out_unregister; + } + + err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ | SA_SAMPLE_RANDOM, + DRV_NAME, hw); if (err) { printk(KERN_ERR PFX "%s: cannot assign irq %d\n", pci_name(pdev), pdev->irq); @@ -3184,6 +3297,8 @@ static int __devinit sky2_probe(struct pci_dev *pdev, return 0; err_out_unregister: + if (hw->msi) + pci_disable_msi(pdev); if (dev1) { unregister_netdev(dev1); free_netdev(dev1); @@ -3226,6 +3341,8 @@ static void __devexit sky2_remove(struct pci_dev *pdev) sky2_read8(hw, B0_CTST); free_irq(pdev->irq, hw); + if (hw->msi) + pci_disable_msi(pdev); pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma); pci_release_regions(pdev); pci_disable_device(pdev); @@ -3263,25 +3380,33 @@ static int sky2_suspend(struct pci_dev *pdev, pm_message_t state) static int sky2_resume(struct pci_dev *pdev) { struct sky2_hw *hw = pci_get_drvdata(pdev); - int i; + int i, err; pci_restore_state(pdev); pci_enable_wake(pdev, PCI_D0, 0); - sky2_set_power_state(hw, PCI_D0); + err = sky2_set_power_state(hw, PCI_D0); + if (err) + goto out; - sky2_reset(hw); + err = sky2_reset(hw); + if (err) + goto out; for (i = 0; i < 2; i++) { struct net_device *dev = hw->dev[i]; - if (dev) { - if (netif_running(dev)) { - netif_device_attach(dev); - if (sky2_up(dev)) - dev_close(dev); + if (dev && netif_running(dev)) { + netif_device_attach(dev); + err = sky2_up(dev); + if (err) { + printk(KERN_ERR PFX "%s: could not up: %d\n", + dev->name, err); + dev_close(dev); + break; } } } - return 0; +out: + return err; } #endif |