diff options
Diffstat (limited to 'drivers/net/wireless/b43/b43.h')
| -rw-r--r-- | drivers/net/wireless/b43/b43.h | 195 |
1 files changed, 144 insertions, 51 deletions
diff --git a/drivers/net/wireless/b43/b43.h b/drivers/net/wireless/b43/b43.h index f13346ba9dd2..eff2a158a411 100644 --- a/drivers/net/wireless/b43/b43.h +++ b/drivers/net/wireless/b43/b43.h @@ -75,6 +75,23 @@ #define B43_MMIO_DMA64_BASE4 0x300 #define B43_MMIO_DMA64_BASE5 0x340 +/* PIO on core rev < 11 */ +#define B43_MMIO_PIO_BASE0 0x300 +#define B43_MMIO_PIO_BASE1 0x310 +#define B43_MMIO_PIO_BASE2 0x320 +#define B43_MMIO_PIO_BASE3 0x330 +#define B43_MMIO_PIO_BASE4 0x340 +#define B43_MMIO_PIO_BASE5 0x350 +#define B43_MMIO_PIO_BASE6 0x360 +#define B43_MMIO_PIO_BASE7 0x370 +/* PIO on core rev >= 11 */ +#define B43_MMIO_PIO11_BASE0 0x200 +#define B43_MMIO_PIO11_BASE1 0x240 +#define B43_MMIO_PIO11_BASE2 0x280 +#define B43_MMIO_PIO11_BASE3 0x2C0 +#define B43_MMIO_PIO11_BASE4 0x300 +#define B43_MMIO_PIO11_BASE5 0x340 + #define B43_MMIO_PHY_VER 0x3E0 #define B43_MMIO_PHY_RADIO 0x3E2 #define B43_MMIO_PHY0 0x3E6 @@ -94,11 +111,14 @@ #define B43_MMIO_GPIO_MASK 0x49E #define B43_MMIO_TSF_CFP_START_LOW 0x604 #define B43_MMIO_TSF_CFP_START_HIGH 0x606 +#define B43_MMIO_TSF_CFP_PRETBTT 0x612 #define B43_MMIO_TSF_0 0x632 /* core rev < 3 only */ #define B43_MMIO_TSF_1 0x634 /* core rev < 3 only */ #define B43_MMIO_TSF_2 0x636 /* core rev < 3 only */ #define B43_MMIO_TSF_3 0x638 /* core rev < 3 only */ #define B43_MMIO_RNG 0x65A +#define B43_MMIO_IFSCTL 0x688 /* Interframe space control */ +#define B43_MMIO_IFSCTL_USE_EDCF 0x0004 #define B43_MMIO_POWERUP_DELAY 0x6A8 /* SPROM boardflags_lo values */ @@ -144,7 +164,8 @@ enum { #define B43_SHM_SH_PHYTYPE 0x0052 /* PHY type */ #define B43_SHM_SH_ANTSWAP 0x005C /* Antenna swap threshold */ #define B43_SHM_SH_HOSTFLO 0x005E /* Hostflags for ucode options (low) */ -#define B43_SHM_SH_HOSTFHI 0x0060 /* Hostflags for ucode options (high) */ +#define B43_SHM_SH_HOSTFMI 0x0060 /* Hostflags for ucode options (middle) */ +#define B43_SHM_SH_HOSTFHI 0x0062 /* Hostflags for ucode options (high) */ #define B43_SHM_SH_RFATT 0x0064 /* Current radio attenuation value */ #define B43_SHM_SH_RADAR 0x0066 /* Radar register */ #define B43_SHM_SH_PHYTXNOI 0x006E /* PHY noise directly after TX (lower 8bit only) */ @@ -232,31 +253,41 @@ enum { #define B43_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4) /* HostFlags. See b43_hf_read/write() */ -#define B43_HF_ANTDIVHELP 0x00000001 /* ucode antenna div helper */ -#define B43_HF_SYMW 0x00000002 /* G-PHY SYM workaround */ -#define B43_HF_RXPULLW 0x00000004 /* RX pullup workaround */ -#define B43_HF_CCKBOOST 0x00000008 /* 4dB CCK power boost (exclusive with OFDM boost) */ -#define B43_HF_BTCOEX 0x00000010 /* Bluetooth coexistance */ -#define B43_HF_GDCW 0x00000020 /* G-PHY DV canceller filter bw workaround */ -#define B43_HF_OFDMPABOOST 0x00000040 /* Enable PA gain boost for OFDM */ -#define B43_HF_ACPR 0x00000080 /* Disable for Japan, channel 14 */ -#define B43_HF_EDCF 0x00000100 /* on if WME and MAC suspended */ -#define B43_HF_TSSIRPSMW 0x00000200 /* TSSI reset PSM ucode workaround */ -#define B43_HF_DSCRQ 0x00000400 /* Disable slow clock request in ucode */ -#define B43_HF_ACIW 0x00000800 /* ACI workaround: shift bits by 2 on PHY CRS */ -#define B43_HF_2060W 0x00001000 /* 2060 radio workaround */ -#define B43_HF_RADARW 0x00002000 /* Radar workaround */ -#define B43_HF_USEDEFKEYS 0x00004000 /* Enable use of default keys */ -#define B43_HF_BT4PRIOCOEX 0x00010000 /* Bluetooth 2-priority coexistance */ -#define B43_HF_FWKUP 0x00020000 /* Fast wake-up ucode */ -#define B43_HF_VCORECALC 0x00040000 /* Force VCO recalculation when powering up synthpu */ -#define B43_HF_PCISCW 0x00080000 /* PCI slow clock workaround */ -#define B43_HF_4318TSSI 0x00200000 /* 4318 TSSI */ -#define B43_HF_FBCMCFIFO 0x00400000 /* Flush bcast/mcast FIFO immediately */ -#define B43_HF_HWPCTL 0x00800000 /* Enable hardwarre power control */ -#define B43_HF_BTCOEXALT 0x01000000 /* Bluetooth coexistance in alternate pins */ -#define B43_HF_TXBTCHECK 0x02000000 /* Bluetooth check during transmission */ -#define B43_HF_SKCFPUP 0x04000000 /* Skip CFP update */ +#define B43_HF_ANTDIVHELP 0x000000000001ULL /* ucode antenna div helper */ +#define B43_HF_SYMW 0x000000000002ULL /* G-PHY SYM workaround */ +#define B43_HF_RXPULLW 0x000000000004ULL /* RX pullup workaround */ +#define B43_HF_CCKBOOST 0x000000000008ULL /* 4dB CCK power boost (exclusive with OFDM boost) */ +#define B43_HF_BTCOEX 0x000000000010ULL /* Bluetooth coexistance */ +#define B43_HF_GDCW 0x000000000020ULL /* G-PHY DC canceller filter bw workaround */ +#define B43_HF_OFDMPABOOST 0x000000000040ULL /* Enable PA gain boost for OFDM */ +#define B43_HF_ACPR 0x000000000080ULL /* Disable for Japan, channel 14 */ +#define B43_HF_EDCF 0x000000000100ULL /* on if WME and MAC suspended */ +#define B43_HF_TSSIRPSMW 0x000000000200ULL /* TSSI reset PSM ucode workaround */ +#define B43_HF_20IN40IQW 0x000000000200ULL /* 20 in 40 MHz I/Q workaround (rev >= 13 only) */ +#define B43_HF_DSCRQ 0x000000000400ULL /* Disable slow clock request in ucode */ +#define B43_HF_ACIW 0x000000000800ULL /* ACI workaround: shift bits by 2 on PHY CRS */ +#define B43_HF_2060W 0x000000001000ULL /* 2060 radio workaround */ +#define B43_HF_RADARW 0x000000002000ULL /* Radar workaround */ +#define B43_HF_USEDEFKEYS 0x000000004000ULL /* Enable use of default keys */ +#define B43_HF_AFTERBURNER 0x000000008000ULL /* Afterburner enabled */ +#define B43_HF_BT4PRIOCOEX 0x000000010000ULL /* Bluetooth 4-priority coexistance */ +#define B43_HF_FWKUP 0x000000020000ULL /* Fast wake-up ucode */ +#define B43_HF_VCORECALC 0x000000040000ULL /* Force VCO recalculation when powering up synthpu */ +#define B43_HF_PCISCW 0x000000080000ULL /* PCI slow clock workaround */ +#define B43_HF_4318TSSI 0x000000200000ULL /* 4318 TSSI */ +#define B43_HF_FBCMCFIFO 0x000000400000ULL /* Flush bcast/mcast FIFO immediately */ +#define B43_HF_HWPCTL 0x000000800000ULL /* Enable hardwarre power control */ +#define B43_HF_BTCOEXALT 0x000001000000ULL /* Bluetooth coexistance in alternate pins */ +#define B43_HF_TXBTCHECK 0x000002000000ULL /* Bluetooth check during transmission */ +#define B43_HF_SKCFPUP 0x000004000000ULL /* Skip CFP update */ +#define B43_HF_N40W 0x000008000000ULL /* N PHY 40 MHz workaround (rev >= 13 only) */ +#define B43_HF_ANTSEL 0x000020000000ULL /* Antenna selection (for testing antenna div.) */ +#define B43_HF_BT3COEXT 0x000020000000ULL /* Bluetooth 3-wire coexistence (rev >= 13 only) */ +#define B43_HF_BTCANT 0x000040000000ULL /* Bluetooth coexistence (antenna mode) (rev >= 13 only) */ +#define B43_HF_ANTSELEN 0x000100000000ULL /* Antenna selection enabled (rev >= 13 only) */ +#define B43_HF_ANTSELMODE 0x000200000000ULL /* Antenna selection mode (rev >= 13 only) */ +#define B43_HF_MLADVW 0x001000000000ULL /* N PHY ML ADV workaround (rev >= 13 only) */ +#define B43_HF_PR45960W 0x080000000000ULL /* PR 45960 workaround (rev >= 13 only) */ /* MacFilter offsets. */ #define B43_MACFILTER_SELF 0x0000 @@ -380,7 +411,6 @@ enum { #define B43_IRQ_ALL 0xFFFFFFFF #define B43_IRQ_MASKTEMPLATE (B43_IRQ_MAC_SUSPENDED | \ - B43_IRQ_BEACON | \ B43_IRQ_TBTT_INDI | \ B43_IRQ_ATIM_END | \ B43_IRQ_PMQ | \ @@ -429,7 +459,6 @@ enum { }; struct b43_dmaring; -struct b43_pioqueue; /* The firmware file header */ #define B43_FW_TYPE_UCODE 'u' @@ -458,20 +487,13 @@ struct b43_iv { } __attribute__((__packed__)); -#define B43_PHYMODE(phytype) (1 << (phytype)) -#define B43_PHYMODE_A B43_PHYMODE(B43_PHYTYPE_A) -#define B43_PHYMODE_B B43_PHYMODE(B43_PHYTYPE_B) -#define B43_PHYMODE_G B43_PHYMODE(B43_PHYTYPE_G) - struct b43_phy { - /* Possible PHYMODEs on this PHY */ - u8 possible_phymodes; + /* Band support flags. */ + bool supports_2ghz; + bool supports_5ghz; + /* GMODE bit enabled? */ bool gmode; - /* Possible ieee80211 subsystem hwmodes for this PHY. - * Which mode is selected, depends on thr GMODE enabled bit */ -#define B43_MAX_PHYHWMODES 2 - struct ieee80211_hw_mode hwmodes[B43_MAX_PHYHWMODES]; /* Analog Type */ u8 analog; @@ -583,15 +605,27 @@ struct b43_phy { /* Data structures for DMA transmission, per 80211 core. */ struct b43_dma { - struct b43_dmaring *tx_ring0; - struct b43_dmaring *tx_ring1; - struct b43_dmaring *tx_ring2; - struct b43_dmaring *tx_ring3; - struct b43_dmaring *tx_ring4; - struct b43_dmaring *tx_ring5; - - struct b43_dmaring *rx_ring0; - struct b43_dmaring *rx_ring3; /* only available on core.rev < 5 */ + struct b43_dmaring *tx_ring_AC_BK; /* Background */ + struct b43_dmaring *tx_ring_AC_BE; /* Best Effort */ + struct b43_dmaring *tx_ring_AC_VI; /* Video */ + struct b43_dmaring *tx_ring_AC_VO; /* Voice */ + struct b43_dmaring *tx_ring_mcast; /* Multicast */ + + struct b43_dmaring *rx_ring; +}; + +struct b43_pio_txqueue; +struct b43_pio_rxqueue; + +/* Data structures for PIO transmission, per 80211 core. */ +struct b43_pio { + struct b43_pio_txqueue *tx_queue_AC_BK; /* Background */ + struct b43_pio_txqueue *tx_queue_AC_BE; /* Best Effort */ + struct b43_pio_txqueue *tx_queue_AC_VI; /* Video */ + struct b43_pio_txqueue *tx_queue_AC_VO; /* Voice */ + struct b43_pio_txqueue *tx_queue_mcast; /* Multicast */ + + struct b43_pio_rxqueue *rx_queue; }; /* Context information for a noise calculation (Link Quality). */ @@ -617,6 +651,35 @@ struct b43_key { u8 algorithm; }; +/* SHM offsets to the QOS data structures for the 4 different queues. */ +#define B43_QOS_PARAMS(queue) (B43_SHM_SH_EDCFQ + \ + (B43_NR_QOSPARAMS * sizeof(u16) * (queue))) +#define B43_QOS_BACKGROUND B43_QOS_PARAMS(0) +#define B43_QOS_BESTEFFORT B43_QOS_PARAMS(1) +#define B43_QOS_VIDEO B43_QOS_PARAMS(2) +#define B43_QOS_VOICE B43_QOS_PARAMS(3) + +/* QOS parameter hardware data structure offsets. */ +#define B43_NR_QOSPARAMS 22 +enum { + B43_QOSPARAM_TXOP = 0, + B43_QOSPARAM_CWMIN, + B43_QOSPARAM_CWMAX, + B43_QOSPARAM_CWCUR, + B43_QOSPARAM_AIFS, + B43_QOSPARAM_BSLOTS, + B43_QOSPARAM_REGGAP, + B43_QOSPARAM_STATUS, +}; + +/* QOS parameters for a queue. */ +struct b43_qos_params { + /* The QOS parameters */ + struct ieee80211_tx_queue_params p; + /* Does this need to get uploaded to hardware? */ + bool need_hw_update; +}; + struct b43_wldev; /* Data structure for the WLAN parts (802.11 cores) of the b43 chip. */ @@ -667,8 +730,16 @@ struct b43_wl { /* The beacon we are currently using (AP or IBSS mode). * This beacon stuff is protected by the irq_lock. */ struct sk_buff *current_beacon; + struct ieee80211_tx_control beacon_txctl; bool beacon0_uploaded; bool beacon1_uploaded; + struct work_struct beacon_update_trigger; + + /* The current QOS parameters for the 4 queues. + * This is protected by the irq_lock. */ + struct b43_qos_params qos_params[4]; + /* Workqueue for updating QOS parameters in hardware. */ + struct work_struct qos_update_work; }; /* In-memory representation of a cached microcode file. */ @@ -727,7 +798,6 @@ struct b43_wldev { bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */ bool dfq_valid; /* Directed frame queue valid (IBSS PS mode, ATIM) */ - bool short_preamble; /* TRUE, if short preamble is enabled. */ bool short_slot; /* TRUE, if short slot timing is enabled. */ bool radio_hw_enable; /* saved state of radio hardware enabled state */ bool suspend_in_progress; /* TRUE, if we are in a suspend/resume cycle */ @@ -735,8 +805,15 @@ struct b43_wldev { /* PHY/Radio device. */ struct b43_phy phy; - /* DMA engines. */ - struct b43_dma dma; + union { + /* DMA engines. */ + struct b43_dma dma; + /* PIO engines. */ + struct b43_pio pio; + }; + /* Use b43_using_pio_transfers() to check whether we are using + * DMA or PIO data transfers. */ + bool __using_pio_transfers; /* Various statistics about the physical device. */ struct b43_stats stats; @@ -820,6 +897,22 @@ static inline void b43_write32(struct b43_wldev *dev, u16 offset, u32 value) ssb_write32(dev->dev, offset, value); } +static inline bool b43_using_pio_transfers(struct b43_wldev *dev) +{ +#ifdef CONFIG_B43_PIO + return dev->__using_pio_transfers; +#else + return 0; +#endif +} + +#ifdef CONFIG_B43_FORCE_PIO +# define B43_FORCE_PIO 1 +#else +# define B43_FORCE_PIO 0 +#endif + + /* Message printing */ void b43info(struct b43_wl *wl, const char *fmt, ...) __attribute__ ((format(printf, 2, 3))); |