diff options
Diffstat (limited to 'drivers/pci/controller/cadence')
| -rw-r--r-- | drivers/pci/controller/cadence/pci-j721e.c | 39 | ||||
| -rw-r--r-- | drivers/pci/controller/cadence/pcie-cadence.c | 4 |
2 files changed, 26 insertions, 17 deletions
diff --git a/drivers/pci/controller/cadence/pci-j721e.c b/drivers/pci/controller/cadence/pci-j721e.c index 284f2e0e4d26..0341d51d6aed 100644 --- a/drivers/pci/controller/cadence/pci-j721e.c +++ b/drivers/pci/controller/cadence/pci-j721e.c @@ -386,6 +386,13 @@ static const struct j721e_pcie_data j784s4_pcie_ep_data = { .max_lanes = 4, }; +static const struct j721e_pcie_data j722s_pcie_rc_data = { + .mode = PCI_MODE_RC, + .linkdown_irq_regfield = J7200_LINK_DOWN, + .byte_access_allowed = true, + .max_lanes = 1, +}; + static const struct of_device_id of_j721e_pcie_match[] = { { .compatible = "ti,j721e-pcie-host", @@ -419,6 +426,10 @@ static const struct of_device_id of_j721e_pcie_match[] = { .compatible = "ti,j784s4-pcie-ep", .data = &j784s4_pcie_ep_data, }, + { + .compatible = "ti,j722s-pcie-host", + .data = &j722s_pcie_rc_data, + }, {}, }; @@ -572,15 +583,14 @@ static int j721e_pcie_probe(struct platform_device *pdev) pcie->refclk = clk; /* - * The "Power Sequencing and Reset Signal Timings" table of the - * PCI Express Card Electromechanical Specification, Revision - * 5.1, Section 2.9.2, Symbol "T_PERST-CLK", indicates PERST# - * should be deasserted after minimum of 100us once REFCLK is - * stable. The REFCLK to the connector in RC mode is selected - * while enabling the PHY. So deassert PERST# after 100 us. + * Section 2.2 of the PCI Express Card Electromechanical + * Specification (Revision 5.1) mandates that the deassertion + * of the PERST# signal should be delayed by 100 ms (TPVPERL). + * This shall ensure that the power and the reference clock + * are stable. */ if (gpiod) { - fsleep(PCIE_T_PERST_CLK_US); + msleep(PCIE_T_PVPERL_MS); gpiod_set_value_cansleep(gpiod, 1); } @@ -671,15 +681,14 @@ static int j721e_pcie_resume_noirq(struct device *dev) return ret; /* - * The "Power Sequencing and Reset Signal Timings" table of the - * PCI Express Card Electromechanical Specification, Revision - * 5.1, Section 2.9.2, Symbol "T_PERST-CLK", indicates PERST# - * should be deasserted after minimum of 100us once REFCLK is - * stable. The REFCLK to the connector in RC mode is selected - * while enabling the PHY. So deassert PERST# after 100 us. + * Section 2.2 of the PCI Express Card Electromechanical + * Specification (Revision 5.1) mandates that the deassertion + * of the PERST# signal should be delayed by 100 ms (TPVPERL). + * This shall ensure that the power and the reference clock + * are stable. */ if (pcie->reset_gpio) { - fsleep(PCIE_T_PERST_CLK_US); + msleep(PCIE_T_PVPERL_MS); gpiod_set_value_cansleep(pcie->reset_gpio, 1); } @@ -712,7 +721,7 @@ static DEFINE_NOIRQ_DEV_PM_OPS(j721e_pcie_pm_ops, static struct platform_driver j721e_pcie_driver = { .probe = j721e_pcie_probe, - .remove_new = j721e_pcie_remove, + .remove = j721e_pcie_remove, .driver = { .name = "j721e-pcie", .of_match_table = of_j721e_pcie_match, diff --git a/drivers/pci/controller/cadence/pcie-cadence.c b/drivers/pci/controller/cadence/pcie-cadence.c index 4251fac5e310..204e045aed8c 100644 --- a/drivers/pci/controller/cadence/pcie-cadence.c +++ b/drivers/pci/controller/cadence/pcie-cadence.c @@ -197,7 +197,7 @@ int cdns_pcie_init_phy(struct device *dev, struct cdns_pcie *pcie) phy_count = of_property_count_strings(np, "phy-names"); if (phy_count < 1) { - dev_err(dev, "no phy-names. PHY will not be initialized\n"); + dev_info(dev, "no \"phy-names\" property found; PHY will not be initialized\n"); pcie->phy_count = 0; return 0; } @@ -260,7 +260,7 @@ static int cdns_pcie_resume_noirq(struct device *dev) ret = cdns_pcie_enable_phy(pcie); if (ret) { - dev_err(dev, "failed to enable phy\n"); + dev_err(dev, "failed to enable PHY\n"); return ret; } |