summaryrefslogtreecommitdiffstats
path: root/drivers/pci
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/pci')
-rw-r--r--drivers/pci/host/Kconfig2
-rw-r--r--drivers/pci/host/pci-imx6.c47
-rw-r--r--drivers/pci/host/pci-rcar-gen2.c180
-rw-r--r--drivers/pci/host/pcie-designware.c2
4 files changed, 153 insertions, 78 deletions
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index 47d46c6d8468..a6f67ec8882f 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -27,7 +27,7 @@ config PCI_TEGRA
config PCI_RCAR_GEN2
bool "Renesas R-Car Gen2 Internal PCI controller"
- depends on ARM && (ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST)
+ depends on ARCH_SHMOBILE || (ARM && COMPILE_TEST)
help
Say Y here if you want internal PCI support on R-Car Gen2 SoC.
There are 3 internal PCI controllers available with a single
diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
index e8663a8c3406..ee082509b0ba 100644
--- a/drivers/pci/host/pci-imx6.c
+++ b/drivers/pci/host/pci-imx6.c
@@ -424,20 +424,40 @@ static void imx6_pcie_reset_phy(struct pcie_port *pp)
static int imx6_pcie_link_up(struct pcie_port *pp)
{
- u32 rc, ltssm, rx_valid;
+ u32 rc, debug_r0, rx_valid;
+ int count = 5;
/*
- * Test if the PHY reports that the link is up and also that
- * the link training finished. It might happen that the PHY
- * reports the link is already up, but the link training bit
- * is still set, so make sure to check the training is done
- * as well here.
+ * Test if the PHY reports that the link is up and also that the LTSSM
+ * training finished. There are three possible states of the link when
+ * this code is called:
+ * 1) The link is DOWN (unlikely)
+ * The link didn't come up yet for some reason. This usually means
+ * we have a real problem somewhere. Reset the PHY and exit. This
+ * state calls for inspection of the DEBUG registers.
+ * 2) The link is UP, but still in LTSSM training
+ * Wait for the training to finish, which should take a very short
+ * time. If the training does not finish, we have a problem and we
+ * need to inspect the DEBUG registers. If the training does finish,
+ * the link is up and operating correctly.
+ * 3) The link is UP and no longer in LTSSM training
+ * The link is up and operating correctly.
*/
- rc = readl(pp->dbi_base + PCIE_PHY_DEBUG_R1);
- if ((rc & PCIE_PHY_DEBUG_R1_XMLH_LINK_UP) &&
- !(rc & PCIE_PHY_DEBUG_R1_XMLH_LINK_IN_TRAINING))
- return 1;
-
+ while (1) {
+ rc = readl(pp->dbi_base + PCIE_PHY_DEBUG_R1);
+ if (!(rc & PCIE_PHY_DEBUG_R1_XMLH_LINK_UP))
+ break;
+ if (!(rc & PCIE_PHY_DEBUG_R1_XMLH_LINK_IN_TRAINING))
+ return 1;
+ if (!count--)
+ break;
+ dev_dbg(pp->dev, "Link is up, but still in training\n");
+ /*
+ * Wait a little bit, then re-check if the link finished
+ * the training.
+ */
+ usleep_range(1000, 2000);
+ }
/*
* From L0, initiate MAC entry to gen2 if EP/RC supports gen2.
* Wait 2ms (LTSSM timeout is 24ms, PHY lock is ~5us in gen2).
@@ -446,15 +466,16 @@ static int imx6_pcie_link_up(struct pcie_port *pp)
* to gen2 is stuck
*/
pcie_phy_read(pp->dbi_base, PCIE_PHY_RX_ASIC_OUT, &rx_valid);
- ltssm = readl(pp->dbi_base + PCIE_PHY_DEBUG_R0) & 0x3F;
+ debug_r0 = readl(pp->dbi_base + PCIE_PHY_DEBUG_R0);
if (rx_valid & 0x01)
return 0;
- if (ltssm != 0x0d)
+ if ((debug_r0 & 0x3f) != 0x0d)
return 0;
dev_err(pp->dev, "transition to gen2 is stuck, reset PHY!\n");
+ dev_dbg(pp->dev, "debug_r0=%08x debug_r1=%08x\n", debug_r0, rc);
imx6_pcie_reset_phy(pp);
diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
index ceec147baec3..fd3e3ab56509 100644
--- a/drivers/pci/host/pci-rcar-gen2.c
+++ b/drivers/pci/host/pci-rcar-gen2.c
@@ -18,6 +18,7 @@
#include <linux/pci.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
+#include <linux/sizes.h>
#include <linux/slab.h>
/* AHB-PCI Bridge PCI communication registers */
@@ -39,9 +40,26 @@
#define RCAR_PCI_INT_ENABLE_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x20)
#define RCAR_PCI_INT_STATUS_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x24)
+#define RCAR_PCI_INT_SIGTABORT (1 << 0)
+#define RCAR_PCI_INT_SIGRETABORT (1 << 1)
+#define RCAR_PCI_INT_REMABORT (1 << 2)
+#define RCAR_PCI_INT_PERR (1 << 3)
+#define RCAR_PCI_INT_SIGSERR (1 << 4)
+#define RCAR_PCI_INT_RESERR (1 << 5)
+#define RCAR_PCI_INT_WIN1ERR (1 << 12)
+#define RCAR_PCI_INT_WIN2ERR (1 << 13)
#define RCAR_PCI_INT_A (1 << 16)
#define RCAR_PCI_INT_B (1 << 17)
#define RCAR_PCI_INT_PME (1 << 19)
+#define RCAR_PCI_INT_ALLERRORS (RCAR_PCI_INT_SIGTABORT | \
+ RCAR_PCI_INT_SIGRETABORT | \
+ RCAR_PCI_INT_SIGRETABORT | \
+ RCAR_PCI_INT_REMABORT | \
+ RCAR_PCI_INT_PERR | \
+ RCAR_PCI_INT_SIGSERR | \
+ RCAR_PCI_INT_RESERR | \
+ RCAR_PCI_INT_WIN1ERR | \
+ RCAR_PCI_INT_WIN2ERR)
#define RCAR_AHB_BUS_CTR_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x30)
#define RCAR_AHB_BUS_MMODE_HTRANS (1 << 0)
@@ -74,9 +92,6 @@
#define RCAR_PCI_UNIT_REV_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x48)
-/* Number of internal PCI controllers */
-#define RCAR_PCI_NR_CONTROLLERS 3
-
struct rcar_pci_priv {
struct device *dev;
void __iomem *reg;
@@ -84,6 +99,7 @@ struct rcar_pci_priv {
struct resource mem_res;
struct resource *cfg_res;
int irq;
+ unsigned long window_size;
};
/* PCI configuration space operations */
@@ -102,6 +118,10 @@ static void __iomem *rcar_pci_cfg_base(struct pci_bus *bus, unsigned int devfn,
if (slot > 2)
return NULL;
+ /* bridge logic only has registers to 0x40 */
+ if (slot == 0x0 && where >= 0x40)
+ return NULL;
+
val = slot ? RCAR_AHBPCI_WIN1_DEVICE | RCAR_AHBPCI_WIN_CTR_CFG :
RCAR_AHBPCI_WIN1_HOST | RCAR_AHBPCI_WIN_CTR_CFG;
@@ -156,7 +176,7 @@ static int rcar_pci_write_config(struct pci_bus *bus, unsigned int devfn,
}
/* PCI interrupt mapping */
-static int __init rcar_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+static int rcar_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
{
struct pci_sys_data *sys = dev->bus->sysdata;
struct rcar_pci_priv *priv = sys->private_data;
@@ -164,8 +184,48 @@ static int __init rcar_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
return priv->irq;
}
+#ifdef CONFIG_PCI_DEBUG
+/* if debug enabled, then attach an error handler irq to the bridge */
+
+static irqreturn_t rcar_pci_err_irq(int irq, void *pw)
+{
+ struct rcar_pci_priv *priv = pw;
+ u32 status = ioread32(priv->reg + RCAR_PCI_INT_STATUS_REG);
+
+ if (status & RCAR_PCI_INT_ALLERRORS) {
+ dev_err(priv->dev, "error irq: status %08x\n", status);
+
+ /* clear the error(s) */
+ iowrite32(status & RCAR_PCI_INT_ALLERRORS,
+ priv->reg + RCAR_PCI_INT_STATUS_REG);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+static void rcar_pci_setup_errirq(struct rcar_pci_priv *priv)
+{
+ int ret;
+ u32 val;
+
+ ret = devm_request_irq(priv->dev, priv->irq, rcar_pci_err_irq,
+ IRQF_SHARED, "error irq", priv);
+ if (ret) {
+ dev_err(priv->dev, "cannot claim IRQ for error handling\n");
+ return;
+ }
+
+ val = ioread32(priv->reg + RCAR_PCI_INT_ENABLE_REG);
+ val |= RCAR_PCI_INT_ALLERRORS;
+ iowrite32(val, priv->reg + RCAR_PCI_INT_ENABLE_REG);
+}
+#else
+static inline void rcar_pci_setup_errirq(struct rcar_pci_priv *priv) { }
+#endif
+
/* PCI host controller setup */
-static int __init rcar_pci_setup(int nr, struct pci_sys_data *sys)
+static int rcar_pci_setup(int nr, struct pci_sys_data *sys)
{
struct rcar_pci_priv *priv = sys->private_data;
void __iomem *reg = priv->reg;
@@ -183,10 +243,31 @@ static int __init rcar_pci_setup(int nr, struct pci_sys_data *sys)
iowrite32(val, reg + RCAR_USBCTR_REG);
udelay(4);
- /* De-assert reset and set PCIAHB window1 size to 1GB */
+ /* De-assert reset and reset PCIAHB window1 size */
val &= ~(RCAR_USBCTR_PCIAHB_WIN1_MASK | RCAR_USBCTR_PCICLK_MASK |
RCAR_USBCTR_USBH_RST | RCAR_USBCTR_PLL_RST);
- iowrite32(val | RCAR_USBCTR_PCIAHB_WIN1_1G, reg + RCAR_USBCTR_REG);
+
+ /* Setup PCIAHB window1 size */
+ switch (priv->window_size) {
+ case SZ_2G:
+ val |= RCAR_USBCTR_PCIAHB_WIN1_2G;
+ break;
+ case SZ_1G:
+ val |= RCAR_USBCTR_PCIAHB_WIN1_1G;
+ break;
+ case SZ_512M:
+ val |= RCAR_USBCTR_PCIAHB_WIN1_512M;
+ break;
+ default:
+ pr_warn("unknown window size %ld - defaulting to 256M\n",
+ priv->window_size);
+ priv->window_size = SZ_256M;
+ /* fall-through */
+ case SZ_256M:
+ val |= RCAR_USBCTR_PCIAHB_WIN1_256M;
+ break;
+ }
+ iowrite32(val, reg + RCAR_USBCTR_REG);
/* Configure AHB master and slave modes */
iowrite32(RCAR_AHB_BUS_MODE, reg + RCAR_AHB_BUS_CTR_REG);
@@ -197,7 +278,7 @@ static int __init rcar_pci_setup(int nr, struct pci_sys_data *sys)
RCAR_PCI_ARBITER_PCIBP_MODE;
iowrite32(val, reg + RCAR_PCI_ARBITER_CTR_REG);
- /* PCI-AHB mapping: 0x40000000-0x80000000 */
+ /* PCI-AHB mapping: 0x40000000 base */
iowrite32(0x40000000 | RCAR_PCIAHB_PREFETCH16,
reg + RCAR_PCIAHB_WIN1_CTR_REG);
@@ -224,10 +305,15 @@ static int __init rcar_pci_setup(int nr, struct pci_sys_data *sys)
iowrite32(RCAR_PCI_INT_A | RCAR_PCI_INT_B | RCAR_PCI_INT_PME,
reg + RCAR_PCI_INT_ENABLE_REG);
+ if (priv->irq > 0)
+ rcar_pci_setup_errirq(priv);
+
/* Add PCI resources */
pci_add_resource(&sys->resources, &priv->io_res);
pci_add_resource(&sys->resources, &priv->mem_res);
+ /* Setup bus number based on platform device id */
+ sys->busnr = to_platform_device(priv->dev)->id;
return 1;
}
@@ -236,48 +322,13 @@ static struct pci_ops rcar_pci_ops = {
.write = rcar_pci_write_config,
};
-static struct hw_pci rcar_hw_pci __initdata = {
- .map_irq = rcar_pci_map_irq,
- .ops = &rcar_pci_ops,
- .setup = rcar_pci_setup,
-};
-
-static int rcar_pci_count __initdata;
-
-static int __init rcar_pci_add_controller(struct rcar_pci_priv *priv)
-{
- void **private_data;
- int count;
-
- if (rcar_hw_pci.nr_controllers < rcar_pci_count)
- goto add_priv;
-
- /* (Re)allocate private data pointer array if needed */
- count = rcar_pci_count + RCAR_PCI_NR_CONTROLLERS;
- private_data = kzalloc(count * sizeof(void *), GFP_KERNEL);
- if (!private_data)
- return -ENOMEM;
-
- rcar_pci_count = count;
- if (rcar_hw_pci.private_data) {
- memcpy(private_data, rcar_hw_pci.private_data,
- rcar_hw_pci.nr_controllers * sizeof(void *));
- kfree(rcar_hw_pci.private_data);
- }
-
- rcar_hw_pci.private_data = private_data;
-
-add_priv:
- /* Add private data pointer to the array */
- rcar_hw_pci.private_data[rcar_hw_pci.nr_controllers++] = priv;
- return 0;
-}
-
-static int __init rcar_pci_probe(struct platform_device *pdev)
+static int rcar_pci_probe(struct platform_device *pdev)
{
struct resource *cfg_res, *mem_res;
struct rcar_pci_priv *priv;
void __iomem *reg;
+ struct hw_pci hw;
+ void *hw_private[1];
cfg_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
reg = devm_ioremap_resource(&pdev->dev, cfg_res);
@@ -308,31 +359,34 @@ static int __init rcar_pci_probe(struct platform_device *pdev)
priv->reg = reg;
priv->dev = &pdev->dev;
- return rcar_pci_add_controller(priv);
+ if (priv->irq < 0) {
+ dev_err(&pdev->dev, "no valid irq found\n");
+ return priv->irq;
+ }
+
+ priv->window_size = SZ_1G;
+
+ hw_private[0] = priv;
+ memset(&hw, 0, sizeof(hw));
+ hw.nr_controllers = ARRAY_SIZE(hw_private);
+ hw.private_data = hw_private;
+ hw.map_irq = rcar_pci_map_irq;
+ hw.ops = &rcar_pci_ops;
+ hw.setup = rcar_pci_setup;
+ pci_common_init_dev(&pdev->dev, &hw);
+ return 0;
}
static struct platform_driver rcar_pci_driver = {
.driver = {
.name = "pci-rcar-gen2",
+ .owner = THIS_MODULE,
+ .suppress_bind_attrs = true,
},
+ .probe = rcar_pci_probe,
};
-static int __init rcar_pci_init(void)
-{
- int retval;
-
- retval = platform_driver_probe(&rcar_pci_driver, rcar_pci_probe);
- if (!retval)
- pci_common_init(&rcar_hw_pci);
-
- /* Private data pointer array is not needed any more */
- kfree(rcar_hw_pci.private_data);
- rcar_hw_pci.private_data = NULL;
-
- return retval;
-}
-
-subsys_initcall(rcar_pci_init);
+module_platform_driver(rcar_pci_driver);
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("Renesas R-Car Gen2 internal PCI");
diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c
index 17ce88f79d2b..6d23d8c893cd 100644
--- a/drivers/pci/host/pcie-designware.c
+++ b/drivers/pci/host/pcie-designware.c
@@ -800,7 +800,7 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
/* setup RC BARs */
dw_pcie_writel_rc(pp, 0x00000004, PCI_BASE_ADDRESS_0);
- dw_pcie_writel_rc(pp, 0x00000004, PCI_BASE_ADDRESS_1);
+ dw_pcie_writel_rc(pp, 0x00000000, PCI_BASE_ADDRESS_1);
/* setup interrupt pins */
dw_pcie_readl_rc(pp, PCI_INTERRUPT_LINE, &val);
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-21 03:31:32 +0100