diff options
Diffstat (limited to 'drivers/serial/Kconfig')
| -rw-r--r-- | drivers/serial/Kconfig | 107 |
1 files changed, 68 insertions, 39 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 812bae62c8ec..b3c561abe3f6 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -23,7 +23,7 @@ config SERIAL_8250 work.) To compile this driver as a module, choose M here: the - module will be called serial. + module will be called 8250. [WARNING: Do not compile this driver as a module if you are using non-standard serial ports, since the configuration information will be lost when the driver is unloaded. This limitation may be lifted @@ -95,6 +95,17 @@ config SERIAL_8250_NR_UARTS PCI enumeration and any ports that may be added at run-time via hot-plug, or any ISA multi-port serial cards. +config SERIAL_8250_RUNTIME_UARTS + int "Number of 8250/16550 serial ports to register at runtime" + depends on SERIAL_8250 + range 0 SERIAL_8250_NR_UARTS + default "4" + help + Set this to the maximum number of serial ports you want + the kernel to register at boot time. This can be overriden + with the module parameter "nr_uarts", or boot-time parameter + 8250.nr_uarts + config SERIAL_8250_EXTENDED bool "Extended 8250/16550 serial driver options" depends on SERIAL_8250 @@ -180,7 +191,6 @@ config SERIAL_8250_BOCA To compile this driver as a module, choose M here: the module will be called 8250_boca. - config SERIAL_8250_HUB6 tristate "Support Hub6 cards" depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS @@ -270,6 +280,40 @@ config SERIAL_AMBA_PL011_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) +config SERIAL_AT91 + bool "AT91RM9200 serial port support" + depends on ARM && ARCH_AT91RM9200 + select SERIAL_CORE + help + This enables the driver for the on-chip UARTs of the AT91RM9200 + processor. + +config SERIAL_AT91_CONSOLE + bool "Support for console on AT91RM9200 serial port" + depends on SERIAL_AT91=y + select SERIAL_CORE_CONSOLE + help + Say Y here if you wish to use a UART on the AT91RM9200 as the system + console (the system console is the device which receives all kernel + messages and warnings and which allows logins in single user mode). + +config SERIAL_AT91_TTYAT + bool "Install as device ttyAT0-4 instead of ttyS0-4" + depends on SERIAL_AT91=y + help + Say Y here if you wish to have the five internal AT91RM9200 UARTs + appear as /dev/ttyAT0-4 (major 204, minor 154-158) instead of the + normal /dev/ttyS0-4 (major 4, minor 64-68). This is necessary if + you also want other UARTs, such as external 8250/16C550 compatible + UARTs. + The ttySn nodes are legally reserved for the 8250 serial driver + but are often misused by other serial drivers. + + To use this, you should create suitable ttyATn device nodes in + /dev/, and pass "console=ttyATn" to the kernel. + + Say Y if you have an external 8250/16C550 UART. If unsure, say N. + config SERIAL_CLPS711X tristate "CLPS711X serial port support" depends on ARM && ARCH_CLPS711X @@ -359,29 +403,6 @@ config SERIAL_21285_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) -config SERIAL_UART00 - bool "Excalibur serial port (uart00) support" - depends on ARM && ARCH_CAMELOT - select SERIAL_CORE - help - Say Y here if you want to use the hard logic uart on Excalibur. This - driver also supports soft logic implementations of this uart core. - -config SERIAL_UART00_CONSOLE - bool "Support for console on Excalibur serial port" - depends on SERIAL_UART00 - select SERIAL_CORE_CONSOLE - help - Say Y here if you want to support a serial console on an Excalibur - hard logic uart or uart00 IP core. - - Even if you say Y here, the currently visible virtual console - (/dev/tty0) will still be used as the system console by default, but - you can alter that using a kernel command line option such as - "console=ttyS1". (Try "man bootparam" or see the documentation of - your boot loader (lilo or loadlin) about how to pass options to the - kernel at boot time.) - config SERIAL_MPSC bool "Marvell MPSC serial port support" depends on PPC32 && MV64X60 @@ -827,7 +848,7 @@ config SERIAL_M32R_SIO_CONSOLE config SERIAL_M32R_PLDSIO bool "M32R SIO I/F on a PLD" - depends on SERIAL_M32R_SIO=y && (PLAT_OPSPUT || PALT_USRV || PLAT_M32700UT) + depends on SERIAL_M32R_SIO=y && (PLAT_OPSPUT || PLAT_USRV || PLAT_M32700UT) default n help Say Y here if you want to use the M32R serial controller @@ -872,20 +893,20 @@ config SERIAL_VR41XX_CONSOLE a console on a serial port, say Y. Otherwise, say N. config SERIAL_JSM - tristate "Digi International NEO PCI Support" + tristate "Digi International NEO PCI Support" depends on PCI - select SERIAL_CORE - help - This is a driver for Digi International's Neo series - of cards which provide multiple serial ports. You would need - something like this to connect more than two modems to your Linux - box, for instance in order to become a dial-in server. This driver - supports PCI boards only. - If you have a card like this, say Y here and read the file - <file:Documentation/jsm.txt>. - - To compile this driver as a module, choose M here: the - module will be called jsm. + select SERIAL_CORE + help + This is a driver for Digi International's Neo series + of cards which provide multiple serial ports. You would need + something like this to connect more than two modems to your Linux + box, for instance in order to become a dial-in server. This driver + supports PCI boards only. + + If you have a card like this, say Y here, otherwise say N. + + To compile this driver as a module, choose M here: the + module will be called jsm. config SERIAL_SGI_IOC4 tristate "SGI IOC4 controller serial support" @@ -896,4 +917,12 @@ config SERIAL_SGI_IOC4 and wish to use the serial ports on this card, say Y. Otherwise, say N. +config SERIAL_SGI_IOC3 + tristate "SGI Altix IOC3 serial support" + depends on (IA64_GENERIC || IA64_SGI_SN2) && SGI_IOC3 + select SERIAL_CORE + help + If you have an SGI Altix with an IOC3 serial card, + say Y or M. Otherwise, say N. + endmenu |