diff options
Diffstat (limited to 'drivers/serial/Kconfig')
| -rw-r--r-- | drivers/serial/Kconfig | 79 |
1 files changed, 65 insertions, 14 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 7fa413ddccf5..d6ae38e55d01 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -88,21 +88,17 @@ config SERIAL_8250_PCI depends on SERIAL_8250 && PCI default SERIAL_8250 help - Say Y here if you have PCI serial ports. - - To compile this driver as a module, choose M here: the module - will be called 8250_pci. + This builds standard PCI serial support. You may be able to + disable this feature if you only need legacy serial support. + Saves about 9K. config SERIAL_8250_PNP tristate "8250/16550 PNP device support" if EMBEDDED depends on SERIAL_8250 && PNP default SERIAL_8250 help - Say Y here if you have serial ports described by PNPBIOS or ACPI. - These are typically ports built into the system board. - - To compile this driver as a module, choose M here: the module - will be called 8250_pnp. + This builds standard PNP serial support. You may be able to + disable this feature if you only need legacy serial support. config SERIAL_8250_HP300 tristate @@ -486,6 +482,36 @@ config SERIAL_DZ_CONSOLE If unsure, say Y. +config SERIAL_ZS + tristate "DECstation Z85C30 serial support" + depends on MACH_DECSTATION + select SERIAL_CORE + default y + ---help--- + Support for the Zilog 85C350 serial communications controller used + for serial ports in newer DECstation systems. These include the + DECsystem 5900 and all models of the DECstation and DECsystem 5000 + systems except from model 200. + + If unsure, say Y. To compile this driver as a module, choose M here: + the module will be called zs. + +config SERIAL_ZS_CONSOLE + bool "Support for console on a DECstation Z85C30 serial port" + depends on SERIAL_ZS=y + select SERIAL_CORE_CONSOLE + default y + ---help--- + If you say Y here, it will be possible to use a serial port as the + system console (the system console is the device which receives all + kernel messages and warnings and which allows logins in single user + mode). + + Note that the firmware uses ttyS1 as the serial console on the + Maxine and ttyS3 on the others using this driver. + + If unsure, say Y. + config SERIAL_21285 tristate "DC21285 serial port support" depends on ARM && FOOTBRIDGE @@ -585,7 +611,7 @@ config SERIAL_BFIN config SERIAL_BFIN_CONSOLE bool "Console on Blackfin serial port" - depends on SERIAL_BFIN + depends on SERIAL_BFIN=y select SERIAL_CORE_CONSOLE choice @@ -806,10 +832,10 @@ config SERIAL_MUX 4. Change the kernel command console parameter to: console=ttyB0 config SERIAL_MUX_CONSOLE - bool "Support for console on serial MUX" - depends on SERIAL_MUX + bool "Support for console on serial MUX" + depends on SERIAL_MUX=y select SERIAL_CORE_CONSOLE - default y + default y config PDC_CONSOLE bool "PDC software console support" @@ -960,6 +986,31 @@ config SERIAL_PMACZILOG PowerMac machines. Say Y or M if you want to be able to these serial ports. +config SERIAL_PMACZILOG_TTYS + bool "Use ttySn device nodes for Zilog z85c30" + depends on SERIAL_PMACZILOG + help + The pmac_zilog driver for the z85C30 chip on many powermacs + historically used the device numbers for /dev/ttySn. The + 8250 serial port driver also uses these numbers, which means + the two drivers being unable to coexist; you could not use + both z85C30 and 8250 type ports at the same time. + + If this option is not selected, the pmac_zilog driver will + use the device numbers allocated for /dev/ttyPZn. This allows + the pmac_zilog and 8250 drivers to co-exist, but may cause + existing userspace setups to break. Programs that need to + access the built-in serial ports on powermacs will need to + be reconfigured to use /dev/ttyPZn instead of /dev/ttySn. + + If you enable this option, any z85c30 ports in the system will + be registered as ttyS0 onwards as in the past, and you will be + unable to use the 8250 module for PCMCIA or other 16C550-style + UARTs. + + Say N unless you need the z85c30 ports on your powermac + to appear as /dev/ttySn. + config SERIAL_PMACZILOG_CONSOLE bool "Console on PowerMac z85c30 serial port" depends on SERIAL_PMACZILOG=y @@ -1165,7 +1216,7 @@ config SERIAL_VR41XX config SERIAL_VR41XX_CONSOLE bool "Enable NEC VR4100 series Serial Interface Unit console" - depends on SERIAL_VR41XX + depends on SERIAL_VR41XX=y select SERIAL_CORE_CONSOLE help If you have a NEC VR4100 series processor and you want to use |