diff options
Diffstat (limited to 'drivers/serial')
31 files changed, 873 insertions, 152 deletions
diff --git a/drivers/serial/68328serial.c b/drivers/serial/68328serial.c index 2b8a410e0959..bbf5bc5892c7 100644 --- a/drivers/serial/68328serial.c +++ b/drivers/serial/68328serial.c @@ -200,7 +200,7 @@ static void rs_stop(struct tty_struct *tty) local_irq_restore(flags); } -static void rs_put_char(char ch) +static int rs_put_char(char ch) { int flags, loops = 0; @@ -214,6 +214,7 @@ static void rs_put_char(char ch) UTX_TXDATA = ch; udelay(5); local_irq_restore(flags); + return 1; } static void rs_start(struct tty_struct *tty) @@ -1017,18 +1018,6 @@ static int rs_ioctl(struct tty_struct *tty, struct file * file, tty_wait_until_sent(tty, 0); send_break(info, arg ? arg*(100) : 250); return 0; - case TIOCGSOFTCAR: - error = put_user(C_CLOCAL(tty) ? 1 : 0, - (unsigned long *) arg); - if (error) - return error; - return 0; - case TIOCSSOFTCAR: - get_user(arg, (unsigned long *) arg); - tty->termios->c_cflag = - ((tty->termios->c_cflag & ~CLOCAL) | - (arg ? CLOCAL : 0)); - return 0; case TIOCGSERIAL: if (access_ok(VERIFY_WRITE, (void *) arg, sizeof(struct serial_struct))) @@ -1061,9 +1050,6 @@ static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) { struct m68k_serial *info = (struct m68k_serial *)tty->driver_data; - if (tty->termios->c_cflag == old_termios->c_cflag) - return; - change_speed(info); if ((old_termios->c_cflag & CRTSCTS) && @@ -1140,8 +1126,7 @@ static void rs_close(struct tty_struct *tty, struct file * filp) uart->ustcnt &= ~(USTCNT_RXEN | USTCNT_RX_INTR_MASK); shutdown(info); - if (tty->driver->flush_buffer) - tty->driver->flush_buffer(tty); + rs_flush_buffer(tty); tty_ldisc_flush(tty); tty->closing = 0; diff --git a/drivers/serial/68360serial.c b/drivers/serial/68360serial.c index f59463601874..d9d4e9552a4d 100644 --- a/drivers/serial/68360serial.c +++ b/drivers/serial/68360serial.c @@ -995,10 +995,10 @@ static void rs_360_put_char(struct tty_struct *tty, unsigned char ch) volatile QUICC_BD *bdp; if (serial_paranoia_check(info, tty->name, "rs_put_char")) - return; + return 0; if (!tty) - return; + return 0; bdp = info->tx_cur; while (bdp->status & BD_SC_READY); @@ -1016,6 +1016,7 @@ static void rs_360_put_char(struct tty_struct *tty, unsigned char ch) bdp++; info->tx_cur = (QUICC_BD *)bdp; + return 1; } @@ -1246,7 +1247,7 @@ static int rs_360_tiocmget(struct tty_struct *tty, struct file *file) #ifdef modem_control unsigned char control, status; - if (serial_paranoia_check(info, tty->name, __FUNCTION__)) + if (serial_paranoia_check(info, tty->name, __func__)) return -ENODEV; if (tty->flags & (1 << TTY_IO_ERROR)) @@ -1277,12 +1278,12 @@ static int rs_360_tiocmset(struct tty_struct *tty, struct file *file, ser_info_t *info = (ser_info_t *)tty->driver_data; unsigned int arg; - if (serial_paranoia_check(info, tty->name, __FUNCTION__)) + if (serial_paranoia_check(info, tty->name, __func__)) return -ENODEV; if (tty->flags & (1 << TTY_IO_ERROR)) return -EIO; - + /* FIXME: locking on info->mcr */ if (set & TIOCM_RTS) info->mcr |= UART_MCR_RTS; if (set & TIOCM_DTR) @@ -1436,18 +1437,6 @@ static int rs_360_ioctl(struct tty_struct *tty, struct file * file, return retval; end_break(info); return 0; - case TIOCGSOFTCAR: - /* return put_user(C_CLOCAL(tty) ? 1 : 0, (int *) arg); */ - put_user(C_CLOCAL(tty) ? 1 : 0, (int *) arg); - return 0; - case TIOCSSOFTCAR: - error = get_user(arg, (unsigned int *) arg); - if (error) - return error; - tty->termios->c_cflag = - ((tty->termios->c_cflag & ~CLOCAL) | - (arg ? CLOCAL : 0)); - return 0; #ifdef maybe case TIOCSERGETLSR: /* Get line status register */ return get_lsr_info(info, (unsigned int *) arg); @@ -1665,8 +1654,7 @@ static void rs_360_close(struct tty_struct *tty, struct file * filp) rs_360_wait_until_sent(tty, info->timeout); } shutdown(info); - if (tty->driver->flush_buffer) - tty->driver->flush_buffer(tty); + rs_360_flush_buffer(tty); tty_ldisc_flush(tty); tty->closing = 0; info->event = 0; @@ -1717,6 +1705,7 @@ static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout) printk("jiff=%lu...", jiffies); #endif + lock_kernel(); /* We go through the loop at least once because we can't tell * exactly when the last character exits the shifter. There can * be at least two characters waiting to be sent after the buffers @@ -1745,6 +1734,7 @@ static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout) bdp--; } while (bdp->status & BD_SC_READY); current->state = TASK_RUNNING; + unlock_kernel(); #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); #endif diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index ea41f2626458..a1ca9b7bf2d5 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -2271,7 +2271,8 @@ static int serial8250_request_std_resource(struct uart_8250_port *up) } if (up->port.flags & UPF_IOREMAP) { - up->port.membase = ioremap(up->port.mapbase, size); + up->port.membase = ioremap_nocache(up->port.mapbase, + size); if (!up->port.membase) { release_mem_region(up->port.mapbase, size); ret = -ENOMEM; diff --git a/drivers/serial/8250_early.c b/drivers/serial/8250_early.c index 38776e8b064b..f279745e9fef 100644 --- a/drivers/serial/8250_early.c +++ b/drivers/serial/8250_early.c @@ -153,10 +153,10 @@ static int __init parse_options(struct early_serial8250_device *device, (void __iomem *)__fix_to_virt(FIX_EARLYCON_MEM_BASE); port->membase += port->mapbase & ~PAGE_MASK; #else - port->membase = ioremap(port->mapbase, 64); + port->membase = ioremap_nocache(port->mapbase, 64); if (!port->membase) { printk(KERN_ERR "%s: Couldn't ioremap 0x%llx\n", - __FUNCTION__, + __func__, (unsigned long long)port->mapbase); return -ENOMEM; } diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c index 6e57382b9137..53fa19cf2f06 100644 --- a/drivers/serial/8250_pci.c +++ b/drivers/serial/8250_pci.c @@ -86,7 +86,7 @@ setup_port(struct serial_private *priv, struct uart_port *port, len = pci_resource_len(dev, bar); if (!priv->remapped_bar[bar]) - priv->remapped_bar[bar] = ioremap(base, len); + priv->remapped_bar[bar] = ioremap_nocache(base, len); if (!priv->remapped_bar[bar]) return -ENOMEM; @@ -270,7 +270,7 @@ static int pci_plx9050_init(struct pci_dev *dev) /* * enable/disable interrupts */ - p = ioremap(pci_resource_start(dev, 0), 0x80); + p = ioremap_nocache(pci_resource_start(dev, 0), 0x80); if (p == NULL) return -ENOMEM; writel(irq_config, p + 0x4c); @@ -294,7 +294,7 @@ static void __devexit pci_plx9050_exit(struct pci_dev *dev) /* * disable interrupts */ - p = ioremap(pci_resource_start(dev, 0), 0x80); + p = ioremap_nocache(pci_resource_start(dev, 0), 0x80); if (p != NULL) { writel(0, p + 0x4c); @@ -341,7 +341,8 @@ static int sbs_init(struct pci_dev *dev) { u8 __iomem *p; - p = ioremap(pci_resource_start(dev, 0), pci_resource_len(dev, 0)); + p = ioremap_nocache(pci_resource_start(dev, 0), + pci_resource_len(dev, 0)); if (p == NULL) return -ENOMEM; @@ -365,7 +366,8 @@ static void __devexit sbs_exit(struct pci_dev *dev) { u8 __iomem *p; - p = ioremap(pci_resource_start(dev, 0), pci_resource_len(dev, 0)); + p = ioremap_nocache(pci_resource_start(dev, 0), + pci_resource_len(dev, 0)); /* FIXME: What if resource_len < OCT_REG_CR_OFF */ if (p != NULL) writeb(0, p + OCT_REG_CR_OFF); @@ -419,7 +421,7 @@ static int pci_siig10x_init(struct pci_dev *dev) break; } - p = ioremap(pci_resource_start(dev, 0), 0x80); + p = ioremap_nocache(pci_resource_start(dev, 0), 0x80); if (p == NULL) return -ENOMEM; diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 34b809e3b596..36acbcca2d48 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -1355,4 +1355,47 @@ config SERIAL_SC26XX_CONSOLE help Support for Console on SC2681/SC2692 serial ports. +config SERIAL_BFIN_SPORT + tristate "Blackfin SPORT emulate UART (EXPERIMENTAL)" + depends on BFIN && EXPERIMENTAL + select SERIAL_CORE + help + Enble support SPORT emulate UART on Blackfin series. + + To compile this driver as a module, choose M here: the + module will be called bfin_sport_uart. + +choice + prompt "Baud rate for Blackfin SPORT UART" + depends on SERIAL_BFIN_SPORT + default SERIAL_SPORT_BAUD_RATE_57600 + help + Choose a baud rate for the SPORT UART, other uart settings are + 8 bit, 1 stop bit, no parity, no flow control. + +config SERIAL_SPORT_BAUD_RATE_115200 + bool "115200" + +config SERIAL_SPORT_BAUD_RATE_57600 + bool "57600" + +config SERIAL_SPORT_BAUD_RATE_38400 + bool "38400" + +config SERIAL_SPORT_BAUD_RATE_19200 + bool "19200" + +config SERIAL_SPORT_BAUD_RATE_9600 + bool "9600" +endchoice + +config SPORT_BAUD_RATE + int + depends on SERIAL_BFIN_SPORT + default 115200 if (SERIAL_SPORT_BAUD_RATE_115200) + default 57600 if (SERIAL_SPORT_BAUD_RATE_57600) + default 38400 if (SERIAL_SPORT_BAUD_RATE_38400) + default 19200 if (SERIAL_SPORT_BAUD_RATE_19200) + default 9600 if (SERIAL_SPORT_BAUD_RATE_9600) + endmenu diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index f02ff9fad017..0d9c09b1e836 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_SERIAL_PXA) += pxa.o obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o obj-$(CONFIG_SERIAL_SA1100) += sa1100.o obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o +obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c index 5f55534a290b..8a2f6a1baa74 100644 --- a/drivers/serial/bfin_5xx.c +++ b/drivers/serial/bfin_5xx.c @@ -762,7 +762,7 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios, break; default: printk(KERN_ERR "%s: word lengh not supported\n", - __FUNCTION__); + __func__); } if (termios->c_cflag & CSTOPB) @@ -1029,7 +1029,7 @@ bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud, *baud = get_sclk() / (16*(dll | dlh << 8)); } - pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __FUNCTION__, *baud, *parity, *bits); + pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits); } #endif diff --git a/drivers/serial/bfin_sport_uart.c b/drivers/serial/bfin_sport_uart.c new file mode 100644 index 000000000000..aca1240ad808 --- /dev/null +++ b/drivers/serial/bfin_sport_uart.c @@ -0,0 +1,614 @@ +/* + * File: linux/drivers/serial/bfin_sport_uart.c + * + * Based on: drivers/serial/bfin_5xx.c by Aubrey Li. + * Author: Roy Huang <roy.huang@analog.com> + * + * Created: Nov 22, 2006 + * Copyright: (c) 2006-2007 Analog Devices Inc. + * Description: this driver enable SPORTs on Blackfin emulate UART. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +/* + * This driver and the hardware supported are in term of EE-191 of ADI. + * http://www.analog.com/UploadedFiles/Application_Notes/399447663EE191.pdf + * This application note describe how to implement a UART on a Sharc DSP, + * but this driver is implemented on Blackfin Processor. + */ + +/* After reset, there is a prelude of low level pulse when transmit data first + * time. No addtional pulse in following transmit. + * According to document: + * The SPORTs are ready to start transmitting or receiving data no later than + * three serial clock cycles after they are enabled in the SPORTx_TCR1 or + * SPORTx_RCR1 register. No serial clock cycles are lost from this point on. + * The first internal frame sync will occur one frame sync delay after the + * SPORTs are ready. External frame syncs can occur as soon as the SPORT is + * ready. + */ + +/* Thanks to Axel Alatalo <axel@rubico.se> for fixing sport rx bug. Sometimes + * sport receives data incorrectly. The following is Axel's words. + * As EE-191, sport rx samples 3 times of the UART baudrate and takes the + * middle smaple of every 3 samples as the data bit. For a 8-N-1 UART setting, + * 30 samples will be required for a byte. If transmitter sends a 1/3 bit short + * byte due to buadrate drift, then the 30th sample of a byte, this sample is + * also the third sample of the stop bit, will happens on the immediately + * following start bit which will be thrown away and missed. Thus since parts + * of the startbit will be missed and the receiver will begin to drift, the + * effect accumulates over time until synchronization is lost. + * If only require 2 samples of the stopbit (by sampling in total 29 samples), + * then a to short byte as in the case above will be tolerated. Then the 1/3 + * early startbit will trigger a framesync since the last read is complete + * after only 2/3 stopbit and framesync is active during the last 1/3 looking + * for a possible early startbit. */ + +//#define DEBUG + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/platform_device.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> + +#include <asm/delay.h> +#include <asm/portmux.h> + +#include "bfin_sport_uart.h" + +unsigned short bfin_uart_pin_req_sport0[] = + {P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS, \ + P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0}; + +unsigned short bfin_uart_pin_req_sport1[] = + {P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS, \ + P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0}; + +#define DRV_NAME "bfin-sport-uart" + +struct sport_uart_port { + struct uart_port port; + char *name; + + int tx_irq; + int rx_irq; + int err_irq; +}; + +static void sport_uart_tx_chars(struct sport_uart_port *up); +static void sport_stop_tx(struct uart_port *port); + +static inline void tx_one_byte(struct sport_uart_port *up, unsigned int value) +{ + pr_debug("%s value:%x\n", __FUNCTION__, value); + /* Place a Start and Stop bit */ + __asm__ volatile ( + "R2 = b#01111111100;\n\t" + "R3 = b#10000000001;\n\t" + "%0 <<= 2;\n\t" + "%0 = %0 & R2;\n\t" + "%0 = %0 | R3;\n\t" + :"=r"(value) + :"0"(value) + :"R2", "R3"); + pr_debug("%s value:%x\n", __FUNCTION__, value); + + SPORT_PUT_TX(up, value); +} + +static inline unsigned int rx_one_byte(struct sport_uart_port *up) +{ + unsigned int value, extract; + + value = SPORT_GET_RX32(up); + pr_debug("%s value:%x\n", __FUNCTION__, value); + + /* Extract 8 bits data */ + __asm__ volatile ( + "R5 = 0;\n\t" + "P0 = 8;\n\t" + "R1 = 0x1801(Z);\n\t" + "R3 = 0x0300(Z);\n\t" + "R4 = 0;\n\t" + "LSETUP(loop_s, loop_e) LC0 = P0;\nloop_s:\t" + "R2 = extract(%1, R1.L)(Z);\n\t" + "R2 <<= R4;\n\t" + "R5 = R5 | R2;\n\t" + "R1 = R1 - R3;\nloop_e:\t" + "R4 += 1;\n\t" + "%0 = R5;\n\t" + :"=r"(extract) + :"r"(value) + :"P0", "R1", "R2","R3","R4", "R5"); + + pr_debug(" extract:%x\n", extract); + return extract; +} + +static int sport_uart_setup(struct sport_uart_port *up, int sclk, int baud_rate) +{ + int tclkdiv, tfsdiv, rclkdiv; + + /* Set TCR1 and TCR2 */ + SPORT_PUT_TCR1(up, (LTFS | ITFS | TFSR | TLSBIT | ITCLK)); + SPORT_PUT_TCR2(up, 10); + pr_debug("%s TCR1:%x, TCR2:%x\n", __FUNCTION__, SPORT_GET_TCR1(up), SPORT_GET_TCR2(up)); + + /* Set RCR1 and RCR2 */ + SPORT_PUT_RCR1(up, (RCKFE | LARFS | LRFS | RFSR | IRCLK)); + SPORT_PUT_RCR2(up, 28); + pr_debug("%s RCR1:%x, RCR2:%x\n", __FUNCTION__, SPORT_GET_RCR1(up), SPORT_GET_RCR2(up)); + + tclkdiv = sclk/(2 * baud_rate) - 1; + tfsdiv = 12; + rclkdiv = sclk/(2 * baud_rate * 3) - 1; + SPORT_PUT_TCLKDIV(up, tclkdiv); + SPORT_PUT_TFSDIV(up, tfsdiv); + SPORT_PUT_RCLKDIV(up, rclkdiv); + SSYNC(); + pr_debug("%s sclk:%d, baud_rate:%d, tclkdiv:%d, tfsdiv:%d, rclkdiv:%d\n", + __FUNCTION__, sclk, baud_rate, tclkdiv, tfsdiv, rclkdiv); + + return 0; +} + +static irqreturn_t sport_uart_rx_irq(int irq, void *dev_id) +{ + struct sport_uart_port *up = dev_id; + struct tty_struct *tty = up->port.info->tty; + unsigned int ch; + + do { + ch = rx_one_byte(up); + up->port.icount.rx++; + + if (uart_handle_sysrq_char(&up->port, ch)) + ; + else + tty_insert_flip_char(tty, ch, TTY_NORMAL); + } while (SPORT_GET_STAT(up) & RXNE); + tty_flip_buffer_push(tty); + + return IRQ_HANDLED; +} + +static irqreturn_t sport_uart_tx_irq(int irq, void *dev_id) +{ + sport_uart_tx_chars(dev_id); + + return IRQ_HANDLED; +} + +static irqreturn_t sport_uart_err_irq(int irq, void *dev_id) +{ + struct sport_uart_port *up = dev_id; + struct tty_struct *tty = up->port.info->tty; + unsigned int stat = SPORT_GET_STAT(up); + + /* Overflow in RX FIFO */ + if (stat & ROVF) { + up->port.icount.overrun++; + tty_insert_flip_char(tty, 0, TTY_OVERRUN); + SPORT_PUT_STAT(up, ROVF); /* Clear ROVF bit */ + } + /* These should not happen */ + if (stat & (TOVF | TUVF | RUVF)) { + printk(KERN_ERR "SPORT Error:%s %s %s\n", + (stat & TOVF)?"TX overflow":"", + (stat & TUVF)?"TX underflow":"", + (stat & RUVF)?"RX underflow":""); + SPORT_PUT_TCR1(up, SPORT_GET_TCR1(up) & ~TSPEN); + SPORT_PUT_RCR1(up, SPORT_GET_RCR1(up) & ~RSPEN); + } + SSYNC(); + + return IRQ_HANDLED; +} + +/* Reqeust IRQ, Setup clock */ +static int sport_startup(struct uart_port *port) +{ + struct sport_uart_port *up = (struct sport_uart_port *)port; + char buffer[20]; + int retval; + + pr_debug("%s enter\n", __FUNCTION__); + memset(buffer, 20, '\0'); + snprintf(buffer, 20, "%s rx", up->name); + retval = request_irq(up->rx_irq, sport_uart_rx_irq, IRQF_SAMPLE_RANDOM, buffer, up); + if (retval) { + printk(KERN_ERR "Unable to request interrupt %s\n", buffer); + return retval; + } + + snprintf(buffer, 20, "%s tx", up->name); + retval = request_irq(up->tx_irq, sport_uart_tx_irq, IRQF_SAMPLE_RANDOM, buffer, up); + if (retval) { + printk(KERN_ERR "Unable to request interrupt %s\n", buffer); + goto fail1; + } + + snprintf(buffer, 20, "%s err", up->name); + retval = request_irq(up->err_irq, sport_uart_err_irq, IRQF_SAMPLE_RANDOM, buffer, up); + if (retval) { + printk(KERN_ERR "Unable to request interrupt %s\n", buffer); + goto fail2; + } + + if (port->line) { + if (peripheral_request_list(bfin_uart_pin_req_sport1, DRV_NAME)) + goto fail3; + } else { + if (peripheral_request_list(bfin_uart_pin_req_sport0, DRV_NAME)) + goto fail3; + } + + sport_uart_setup(up, get_sclk(), port->uartclk); + + /* Enable receive interrupt */ + SPORT_PUT_RCR1(up, (SPORT_GET_RCR1(up) | RSPEN)); + SSYNC(); + + return 0; + + +fail3: + printk(KERN_ERR DRV_NAME + ": Requesting Peripherals failed\n"); + + free_irq(up->err_irq, up); +fail2: + free_irq(up->tx_irq, up); +fail1: + free_irq(up->rx_irq, up); + + return retval; + +} + +static void sport_uart_tx_chars(struct sport_uart_port *up) +{ + struct circ_buf *xmit = &up->port.info->xmit; + + if (SPORT_GET_STAT(up) & TXF) + return; + + if (up->port.x_char) { + tx_one_byte(up, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + + if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { + sport_stop_tx(&up->port); + return; + } + + while(!(SPORT_GET_STAT(up) & TXF) && !uart_circ_empty(xmit)) { + tx_one_byte(up, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE -1); + up->port.icount.tx++; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); +} + +static unsigned int sport_tx_empty(struct uart_port *port) +{ + struct sport_uart_port *up = (struct sport_uart_port *)port; + unsigned int stat; + + stat = SPORT_GET_STAT(up); + pr_debug("%s stat:%04x\n", __FUNCTION__, stat); + if (stat & TXHRE) { + return TIOCSER_TEMT; + } else + return 0; +} + +static unsigned int sport_get_mctrl(struct uart_port *port) +{ + pr_debug("%s enter\n", __FUNCTION__); + return (TIOCM_CTS | TIOCM_CD | TIOCM_DSR); +} + +static void sport_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + pr_debug("%s enter\n", __FUNCTION__); +} + +static void sport_stop_tx(struct uart_port *port) +{ + struct sport_uart_port *up = (struct sport_uart_port *)port; + unsigned int stat; + + pr_debug("%s enter\n", __FUNCTION__); + + stat = SPORT_GET_STAT(up); + while(!(stat & TXHRE)) { + udelay(1); + stat = SPORT_GET_STAT(up); + } + /* Although the hold register is empty, last byte is still in shift + * register and not sent out yet. If baud rate is lower than default, + * delay should be longer. For example, if the baud rate is 9600, + * the delay must be at least 2ms by experience */ + udelay(500); + + SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) & ~TSPEN)); + SSYNC(); + + return; +} + +static void sport_start_tx(struct uart_port *port) +{ + struct sport_uart_port *up = (struct sport_uart_port *)port; + + pr_debug("%s enter\n", __FUNCTION__); + /* Write data into SPORT FIFO before enable SPROT to transmit */ + sport_uart_tx_chars(up); + + /* Enable transmit, then an interrupt will generated */ + SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) | TSPEN)); + SSYNC(); + pr_debug("%s exit\n", __FUNCTION__); +} + +static void sport_stop_rx(struct uart_port *port) +{ + struct sport_uart_port *up = (struct sport_uart_port *)port; + + pr_debug("%s enter\n", __FUNCTION__); + /* Disable sport to stop rx */ + SPORT_PUT_RCR1(up, (SPORT_GET_RCR1(up) & ~RSPEN)); + SSYNC(); +} + +static void sport_enable_ms(struct uart_port *port) +{ + pr_debug("%s enter\n", __FUNCTION__); +} + +static void sport_break_ctl(struct uart_port *port, int break_state) +{ + pr_debug("%s enter\n", __FUNCTION__); +} + +static void sport_shutdown(struct uart_port *port) +{ + struct sport_uart_port *up = (struct sport_uart_port *)port; + + pr_debug("%s enter\n", __FUNCTION__); + + /* Disable sport */ + SPORT_PUT_TCR1(up, (SPORT_GET_TCR1(up) & ~TSPEN)); + SPORT_PUT_RCR1(up, (SPORT_GET_RCR1(up) & ~RSPEN)); + SSYNC(); + + if (port->line) { + peripheral_free_list(bfin_uart_pin_req_sport1); + } else { + peripheral_free_list(bfin_uart_pin_req_sport0); + } + + free_irq(up->rx_irq, up); + free_irq(up->tx_irq, up); + free_irq(up->err_irq, up); +} + +static void sport_set_termios(struct uart_port *port, + struct termios *termios, struct termios *old) +{ + pr_debug("%s enter, c_cflag:%08x\n", __FUNCTION__, termios->c_cflag); + uart_update_timeout(port, CS8 ,port->uartclk); +} + +static const char *sport_type(struct uart_port *port) +{ + struct sport_uart_port *up = (struct sport_uart_port *)port; + + pr_debug("%s enter\n", __FUNCTION__); + return up->name; +} + +static void sport_release_port(struct uart_port *port) +{ + pr_debug("%s enter\n", __FUNCTION__); +} + +static int sport_request_port(struct uart_port *port) +{ + pr_debug("%s enter\n", __FUNCTION__); + return 0; +} + +static void sport_config_port(struct uart_port *port, int flags) +{ + struct sport_uart_port *up = (struct sport_uart_port *)port; + + pr_debug("%s enter\n", __FUNCTION__); + up->port.type = PORT_BFIN_SPORT; +} + +static int sport_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + pr_debug("%s enter\n", __FUNCTION__); + return 0; +} + +struct uart_ops sport_uart_ops = { + .tx_empty = sport_tx_empty, + .set_mctrl = sport_set_mctrl, + .get_mctrl = sport_get_mctrl, + .stop_tx = sport_stop_tx, + .start_tx = sport_start_tx, + .stop_rx = sport_stop_rx, + .enable_ms = sport_enable_ms, + .break_ctl = sport_break_ctl, + .startup = sport_startup, + .shutdown = sport_shutdown, + .set_termios = sport_set_termios, + .type = sport_type, + .release_port = sport_release_port, + .request_port = sport_request_port, + .config_port = sport_config_port, + .verify_port = sport_verify_port, +}; + +static struct sport_uart_port sport_uart_ports[] = { + { /* SPORT 0 */ + .name = "SPORT0", + .tx_irq = IRQ_SPORT0_TX, + .rx_irq = IRQ_SPORT0_RX, + .err_irq= IRQ_SPORT0_ERROR, + .port = { + .type = PORT_BFIN_SPORT, + .iotype = UPIO_MEM, + .membase = (void __iomem *)SPORT0_TCR1, + .mapbase = SPORT0_TCR1, + .irq = IRQ_SPORT0_RX, + .uartclk = CONFIG_SPORT_BAUD_RATE, + .fifosize = 8, + .ops = &sport_uart_ops, + .line = 0, + }, + }, { /* SPORT 1 */ + .name = "SPORT1", + .tx_irq = IRQ_SPORT1_TX, + .rx_irq = IRQ_SPORT1_RX, + .err_irq= IRQ_SPORT1_ERROR, + .port = { + .type = PORT_BFIN_SPORT, + .iotype = UPIO_MEM, + .membase = (void __iomem *)SPORT1_TCR1, + .mapbase = SPORT1_TCR1, + .irq = IRQ_SPORT1_RX, + .uartclk = CONFIG_SPORT_BAUD_RATE, + .fifosize = 8, + .ops = &sport_uart_ops, + .line = 1, + }, + } +}; + +static struct uart_driver sport_uart_reg = { + .owner = THIS_MODULE, + .driver_name = "SPORT-UART", + .dev_name = "ttySS", + .major = 204, + .minor = 84, + .nr = ARRAY_SIZE(sport_uart_ports), + .cons = NULL, +}; + +static int sport_uart_suspend(struct platform_device *dev, pm_message_t state) +{ + struct sport_uart_port *sport = platform_get_drvdata(dev); + + pr_debug("%s enter\n", __FUNCTION__); + if (sport) + uart_suspend_port(&sport_uart_reg, &sport->port); + + return 0; +} + +static int sport_uart_resume(struct platform_device *dev) +{ + struct sport_uart_port *sport = platform_get_drvdata(dev); + + pr_debug("%s enter\n", __FUNCTION__); + if (sport) + uart_resume_port(&sport_uart_reg, &sport->port); + + return 0; +} + +static int sport_uart_probe(struct platform_device *dev) +{ + pr_debug("%s enter\n", __FUNCTION__); + sport_uart_ports[dev->id].port.dev = &dev->dev; + uart_add_one_port(&sport_uart_reg, &sport_uart_ports[dev->id].port); + platform_set_drvdata(dev, &sport_uart_ports[dev->id]); + + return 0; +} + +static int sport_uart_remove(struct platform_device *dev) +{ + struct sport_uart_port *sport = platform_get_drvdata(dev); + + pr_debug("%s enter\n", __FUNCTION__); + platform_set_drvdata(dev, NULL); + + if (sport) + uart_remove_one_port(&sport_uart_reg, &sport->port); + + return 0; +} + +static struct platform_driver sport_uart_driver = { + .probe = sport_uart_probe, + .remove = sport_uart_remove, + .suspend = sport_uart_suspend, + .resume = sport_uart_resume, + .driver = { + .name = DRV_NAME, + }, +}; + +static int __init sport_uart_init(void) +{ + int ret; + + pr_debug("%s enter\n", __FUNCTION__); + ret = uart_register_driver(&sport_uart_reg); + if (ret != 0) { + printk(KERN_ERR "Failed to register %s:%d\n", + sport_uart_reg.driver_name, ret); + return ret; + } + + ret = platform_driver_register(&sport_uart_driver); + if (ret != 0) { + printk(KERN_ERR "Failed to register sport uart driver:%d\n", ret); + uart_unregister_driver(&sport_uart_reg); + } + + + pr_debug("%s exit\n", __FUNCTION__); + return ret; +} + +static void __exit sport_uart_exit(void) +{ + pr_debug("%s enter\n", __FUNCTION__); + platform_driver_unregister(&sport_uart_driver); + uart_unregister_driver(&sport_uart_reg); +} + +module_init(sport_uart_init); +module_exit(sport_uart_exit); + +MODULE_LICENSE("GPL"); diff --git a/drivers/serial/bfin_sport_uart.h b/drivers/serial/bfin_sport_uart.h new file mode 100644 index 000000000000..671d41cc1a3f --- /dev/null +++ b/drivers/serial/bfin_sport_uart.h @@ -0,0 +1,63 @@ +/* + * File: linux/drivers/serial/bfin_sport_uart.h + * + * Based on: include/asm-blackfin/mach-533/bfin_serial_5xx.h + * Author: Roy Huang <roy.huang>analog.com> + * + * Created: Nov 22, 2006 + * Copyright: (C) Analog Device Inc. + * Description: this driver enable SPORTs on Blackfin emulate UART. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + + +#define OFFSET_TCR1 0x00 /* Transmit Configuration 1 Register */ +#define OFFSET_TCR2 0x04 /* Transmit Configuration 2 Register */ +#define OFFSET_TCLKDIV 0x08 /* Transmit Serial Clock Divider Register */ +#define OFFSET_TFSDIV 0x0C /* Transmit Frame Sync Divider Register */ +#define OFFSET_TX 0x10 /* Transmit Data Register */ +#define OFFSET_RX 0x18 /* Receive Data Register */ +#define OFFSET_RCR1 0x20 /* Receive Configuration 1 Register */ +#define OFFSET_RCR2 0x24 /* Receive Configuration 2 Register */ +#define OFFSET_RCLKDIV 0x28 /* Receive Serial Clock Divider Register */ +#define OFFSET_RFSDIV 0x2c /* Receive Frame Sync Divider Register */ +#define OFFSET_STAT 0x30 /* Status Register */ + +#define SPORT_GET_TCR1(sport) bfin_read16(((sport)->port.membase + OFFSET_TCR1)) +#define SPORT_GET_TCR2(sport) bfin_read16(((sport)->port.membase + OFFSET_TCR2)) +#define SPORT_GET_TCLKDIV(sport) bfin_read16(((sport)->port.membase + OFFSET_TCLKDIV)) +#define SPORT_GET_TFSDIV(sport) bfin_read16(((sport)->port.membase + OFFSET_TFSDIV)) +#define SPORT_GET_TX(sport) bfin_read16(((sport)->port.membase + OFFSET_TX)) +#define SPORT_GET_RX(sport) bfin_read16(((sport)->port.membase + OFFSET_RX)) +#define SPORT_GET_RX32(sport) bfin_read32(((sport)->port.membase + OFFSET_RX)) +#define SPORT_GET_RCR1(sport) bfin_read16(((sport)->port.membase + OFFSET_RCR1)) +#define SPORT_GET_RCR2(sport) bfin_read16(((sport)->port.membase + OFFSET_RCR2)) +#define SPORT_GET_RCLKDIV(sport) bfin_read16(((sport)->port.membase + OFFSET_RCLKDIV)) +#define SPORT_GET_RFSDIV(sport) bfin_read16(((sport)->port.membase + OFFSET_RFSDIV)) +#define SPORT_GET_STAT(sport) bfin_read16(((sport)->port.membase + OFFSET_STAT)) + +#define SPORT_PUT_TCR1(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TCR1), v) +#define SPORT_PUT_TCR2(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TCR2), v) +#define SPORT_PUT_TCLKDIV(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TCLKDIV), v) +#define SPORT_PUT_TFSDIV(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TFSDIV), v) +#define SPORT_PUT_TX(sport, v) bfin_write16(((sport)->port.membase + OFFSET_TX), v) +#define SPORT_PUT_RX(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RX), v) +#define SPORT_PUT_RCR1(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RCR1), v) +#define SPORT_PUT_RCR2(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RCR2), v) +#define SPORT_PUT_RCLKDIV(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RCLKDIV), v) +#define SPORT_PUT_RFSDIV(sport, v) bfin_write16(((sport)->port.membase + OFFSET_RFSDIV), v) +#define SPORT_PUT_STAT(sport, v) bfin_write16(((sport)->port.membase + OFFSET_STAT), v) diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index a638ba0679ac..a19dc7ef8861 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -1117,7 +1117,7 @@ int cpm_uart_drv_get_platform_data(struct platform_device *pdev, int is_con) line = cpm_uart_id2nr(idx); if(line < 0) { - printk(KERN_ERR"%s(): port %d is not registered", __FUNCTION__, idx); + printk(KERN_ERR"%s(): port %d is not registered", __func__, idx); return -EINVAL; } diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c index 88e7c1d5b919..f9fa237aa949 100644 --- a/drivers/serial/crisv10.c +++ b/drivers/serial/crisv10.c @@ -1788,7 +1788,7 @@ static unsigned int handle_descr_data(struct e100_serial *info, if (info->recv_cnt + recvl > 65536) { printk(KERN_CRIT - "%s: Too much pending incoming serial data! Dropping %u bytes.\n", __FUNCTION__, recvl); + "%s: Too much pending incoming serial data! Dropping %u bytes.\n", __func__, recvl); return 0; } @@ -1801,7 +1801,7 @@ static unsigned int handle_descr_data(struct e100_serial *info, append_recv_buffer(info, buffer); if (!(buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE))) - panic("%s: Failed to allocate memory for receive buffer!\n", __FUNCTION__); + panic("%s: Failed to allocate memory for receive buffer!\n", __func__); descr->buf = virt_to_phys(buffer->buffer); @@ -1925,7 +1925,7 @@ static int start_recv_dma(struct e100_serial *info) /* Set up the receiving descriptors */ for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++) { if (!(buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE))) - panic("%s: Failed to allocate memory for receive buffer!\n", __FUNCTION__); + panic("%s: Failed to allocate memory for receive buffer!\n", __func__); descr[i].ctrl = d_int; descr[i].buf = virt_to_phys(buffer->buffer); @@ -3581,8 +3581,9 @@ rs_tiocmset(struct tty_struct *tty, struct file *file, unsigned int set, unsigned int clear) { struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; - lock_kernel(); + local_irq_save(flags); if (clear & TIOCM_RTS) e100_rts(info, 0); @@ -3604,7 +3605,7 @@ rs_tiocmset(struct tty_struct *tty, struct file *file, if (set & TIOCM_CD) e100_cd_out(info, 1); - unlock_kernel(); + local_irq_restore(flags); return 0; } @@ -3613,8 +3614,10 @@ rs_tiocmget(struct tty_struct *tty, struct file *file) { struct e100_serial *info = (struct e100_serial *)tty->driver_data; unsigned int result; + unsigned long flags; + + local_irq_save(flags); - lock_kernel(); result = (!E100_RTS_GET(info) ? TIOCM_RTS : 0) | (!E100_DTR_GET(info) ? TIOCM_DTR : 0) @@ -3623,7 +3626,7 @@ rs_tiocmget(struct tty_struct *tty, struct file *file) | (!E100_CD_GET(info) ? TIOCM_CAR : 0) | (!E100_CTS_GET(info) ? TIOCM_CTS : 0); - unlock_kernel(); + local_irq_restore(flags); #ifdef SERIAL_DEBUG_IO printk(KERN_DEBUG "ser%i: modem state: %i 0x%08X\n", @@ -3702,10 +3705,6 @@ rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) { struct e100_serial *info = (struct e100_serial *)tty->driver_data; - if (tty->termios->c_cflag == old_termios->c_cflag && - tty->termios->c_iflag == old_termios->c_iflag) - return; - change_speed(info); /* Handle turning off CRTSCTS */ @@ -3808,10 +3807,8 @@ rs_close(struct tty_struct *tty, struct file * filp) #endif shutdown(info); - if (tty->driver->flush_buffer) - tty->driver->flush_buffer(tty); - if (tty->ldisc.flush_buffer) - tty->ldisc.flush_buffer(tty); + rs_flush_buffer(tty); + tty_ldisc_flush_buffer(tty); tty->closing = 0; info->event = 0; info->tty = 0; @@ -3885,6 +3882,7 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout) * Check R_DMA_CHx_STATUS bit 0-6=number of available bytes in FIFO * R_DMA_CHx_HWSW bit 31-16=nbr of bytes left in DMA buffer (0=64k) */ + lock_kernel(); orig_jiffies = jiffies; while (info->xmit.head != info->xmit.tail || /* More in send queue */ (*info->ostatusadr & 0x007f) || /* more in FIFO */ @@ -3901,6 +3899,7 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout) curr_time_usec - info->last_tx_active_usec; } set_current_state(TASK_RUNNING); + unlock_kernel(); } /* @@ -4520,7 +4519,7 @@ rs_init(void) if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial ", driver)) - panic("%s: Failed to request irq8", __FUNCTION__); + panic("%s: Failed to request irq8", __func__); #endif #endif /* CONFIG_SVINTO_SIM */ diff --git a/drivers/serial/ioc3_serial.c b/drivers/serial/ioc3_serial.c index 168073f12cec..4f1af71e9a1b 100644 --- a/drivers/serial/ioc3_serial.c +++ b/drivers/serial/ioc3_serial.c @@ -52,7 +52,7 @@ static unsigned int Submodule_slot; #define DPRINT_CONFIG(_x...) ; //#define DPRINT_CONFIG(_x...) printk _x #define NOT_PROGRESS() ; -//#define NOT_PROGRESS() printk("%s : fails %d\n", __FUNCTION__, __LINE__) +//#define NOT_PROGRESS() printk("%s : fails %d\n", __func__, __LINE__) /* number of characters we want to transmit to the lower level at a time */ #define MAX_CHARS 256 @@ -445,7 +445,7 @@ static int inline port_init(struct ioc3_port *port) sbbr_h = &idd->vma->sbbr_h; ring_pci_addr = (unsigned long __iomem)port->ip_dma_ringbuf; DPRINT_CONFIG(("%s: ring_pci_addr 0x%p\n", - __FUNCTION__, (void *)ring_pci_addr)); + __func__, (void *)ring_pci_addr)); writel((unsigned int)((uint64_t) ring_pci_addr >> 32), sbbr_h); writel((unsigned int)ring_pci_addr | BUF_SIZE_BIT, sbbr_l); @@ -593,7 +593,7 @@ config_port(struct ioc3_port *port, DPRINT_CONFIG(("%s: line %d baud %d byte_size %d stop %d parenb %d " "parodd %d\n", - __FUNCTION__, ((struct uart_port *)port->ip_port)->line, + __func__, ((struct uart_port *)port->ip_port)->line, baud, byte_size, stop_bits, parenb, parodd)); if (set_baud(port, baud)) @@ -871,14 +871,14 @@ static int ioc3_set_proto(struct ioc3_port *port, int proto) default: case PROTO_RS232: /* Clear the appropriate GIO pin */ - DPRINT_CONFIG(("%s: rs232\n", __FUNCTION__)); + DPRINT_CONFIG(("%s: rs232\n", __func__)); writel(0, (&port->ip_idd->vma->gppr[0] + hooks->rs422_select_pin)); break; case PROTO_RS422: /* Set the appropriate GIO pin */ - DPRINT_CONFIG(("%s: rs422\n", __FUNCTION__)); + DPRINT_CONFIG(("%s: rs422\n", __func__)); writel(1, (&port->ip_idd->vma->gppr[0] + hooks->rs422_select_pin)); break; @@ -988,7 +988,7 @@ ioc3_change_speed(struct uart_port *the_port, } baud = uart_get_baud_rate(the_port, new_termios, old_termios, MIN_BAUD_SUPPORTED, MAX_BAUD_SUPPORTED); - DPRINT_CONFIG(("%s: returned baud %d for line %d\n", __FUNCTION__, baud, + DPRINT_CONFIG(("%s: returned baud %d for line %d\n", __func__, baud, the_port->line)); if (!the_port->fifosize) @@ -1026,7 +1026,7 @@ ioc3_change_speed(struct uart_port *the_port, DPRINT_CONFIG(("%s : port 0x%p line %d cflag 0%o " "config_port(baud %d data %d stop %d penable %d " " parity %d), notification 0x%x\n", - __FUNCTION__, (void *)port, the_port->line, cflag, baud, + __func__, (void *)port, the_port->line, cflag, baud, new_data, new_stop, new_parity_enable, new_parity, the_port->ignore_status_mask)); @@ -1919,7 +1919,7 @@ static inline int ioc3_serial_core_attach( struct ioc3_submodule *is, struct pci_dev *pdev = idd->pdev; DPRINT_CONFIG(("%s: attach pdev 0x%p - card_ptr 0x%p\n", - __FUNCTION__, pdev, (void *)card_ptr)); + __func__, pdev, (void *)card_ptr)); if (!card_ptr) return -ENODEV; @@ -1933,7 +1933,7 @@ static inline int ioc3_serial_core_attach( struct ioc3_submodule *is, port->ip_port = the_port; DPRINT_CONFIG(("%s: attach the_port 0x%p / port 0x%p [%d/%d]\n", - __FUNCTION__, (void *)the_port, (void *)port, + __func__, (void *)the_port, (void *)port, phys_port, ii)); /* membase, iobase and mapbase just need to be non-0 */ @@ -1950,7 +1950,7 @@ static inline int ioc3_serial_core_attach( struct ioc3_submodule *is, if (uart_add_one_port(&ioc3_uart, the_port) < 0) { printk(KERN_WARNING "%s: unable to add port %d bus %d\n", - __FUNCTION__, the_port->line, pdev->bus->number); + __func__, the_port->line, pdev->bus->number); } else { DPRINT_CONFIG(("IOC3 serial port %d irq %d bus %d\n", the_port->line, the_port->irq, pdev->bus->number)); @@ -2017,7 +2017,7 @@ ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd) struct ioc3_port *ports[PORTS_PER_CARD]; int phys_port; - DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __FUNCTION__, is, idd)); + DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __func__, is, idd)); card_ptr = kzalloc(sizeof(struct ioc3_card), GFP_KERNEL); if (!card_ptr) { @@ -2067,7 +2067,7 @@ ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd) DPRINT_CONFIG(("%s : Port A ip_serial_regs 0x%p " "ip_uart_regs 0x%p\n", - __FUNCTION__, + __func__, (void *)port->ip_serial_regs, (void *)port->ip_uart_regs)); @@ -2082,7 +2082,7 @@ ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd) DPRINT_CONFIG(("%s : Port A ip_cpu_ringbuf 0x%p " "ip_dma_ringbuf 0x%p, ip_inring 0x%p " "ip_outring 0x%p\n", - __FUNCTION__, + __func__, (void *)port->ip_cpu_ringbuf, (void *)port->ip_dma_ringbuf, (void *)port->ip_inring, @@ -2094,7 +2094,7 @@ ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd) DPRINT_CONFIG(("%s : Port B ip_serial_regs 0x%p " "ip_uart_regs 0x%p\n", - __FUNCTION__, + __func__, (void *)port->ip_serial_regs, (void *)port->ip_uart_regs)); @@ -2108,7 +2108,7 @@ ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd) DPRINT_CONFIG(("%s : Port B ip_cpu_ringbuf 0x%p " "ip_dma_ringbuf 0x%p, ip_inring 0x%p " "ip_outring 0x%p\n", - __FUNCTION__, + __func__, (void *)port->ip_cpu_ringbuf, (void *)port->ip_dma_ringbuf, (void *)port->ip_inring, @@ -2116,7 +2116,7 @@ ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd) } DPRINT_CONFIG(("%s : port %d [addr 0x%p] card_ptr 0x%p", - __FUNCTION__, + __func__, phys_port, (void *)port, (void *)card_ptr)); DPRINT_CONFIG((" ip_serial_regs 0x%p ip_uart_regs 0x%p\n", (void *)port->ip_serial_regs, @@ -2127,7 +2127,7 @@ ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd) DPRINT_CONFIG(("%s: phys_port %d port 0x%p inring 0x%p " "outring 0x%p\n", - __FUNCTION__, + __func__, phys_port, (void *)port, (void *)port->ip_inring, (void *)port->ip_outring)); @@ -2170,7 +2170,7 @@ static int __devinit ioc3uart_init(void) if ((ret = uart_register_driver(&ioc3_uart)) < 0) { printk(KERN_WARNING "%s: Couldn't register IOC3 uart serial driver\n", - __FUNCTION__); + __func__); return ret; } ret = ioc3_register_submodule(&ioc3uart_submodule); diff --git a/drivers/serial/ioc4_serial.c b/drivers/serial/ioc4_serial.c index 0c179384fb0c..49b8a82b7b9f 100644 --- a/drivers/serial/ioc4_serial.c +++ b/drivers/serial/ioc4_serial.c @@ -889,7 +889,7 @@ static int inline port_init(struct ioc4_port *port) ring_pci_addr = (unsigned long __iomem)port->ip_dma_ringbuf; DPRINT_CONFIG(("%s: ring_pci_addr 0x%lx\n", - __FUNCTION__, ring_pci_addr)); + __func__, ring_pci_addr)); writel((unsigned int)((uint64_t)ring_pci_addr >> 32), sbbr_h); writel((unsigned int)ring_pci_addr | IOC4_BUF_SIZE_BIT, sbbr_l); @@ -1028,7 +1028,7 @@ static irqreturn_t ioc4_intr(int irq, void *arg) spin_lock_irqsave(&soft->is_ir_lock, flag); printk ("%s : %d : mem 0x%p sio_ir 0x%x sio_ies 0x%x " "other_ir 0x%x other_ies 0x%x mask 0x%x\n", - __FUNCTION__, __LINE__, + __func__, __LINE__, (void *)mem, readl(&mem->sio_ir.raw), readl(&mem->sio_ies.raw), readl(&mem->other_ir.raw), @@ -1155,14 +1155,14 @@ static int inline ioc4_attach_local(struct ioc4_driver_data *idd) (TOTAL_RING_BUF_SIZE - 1)) == 0)); DPRINT_CONFIG(("%s : ip_cpu_ringbuf 0x%p " "ip_dma_ringbuf 0x%p\n", - __FUNCTION__, + __func__, (void *)port->ip_cpu_ringbuf, (void *)port->ip_dma_ringbuf)); port->ip_inring = RING(port, RX_0_OR_2); port->ip_outring = RING(port, TX_0_OR_2); } DPRINT_CONFIG(("%s : port %d [addr 0x%p] control 0x%p", - __FUNCTION__, + __func__, port_number, (void *)port, (void *)control)); DPRINT_CONFIG((" ip_serial_regs 0x%p ip_uart_regs 0x%p\n", (void *)port->ip_serial_regs, @@ -1173,7 +1173,7 @@ static int inline ioc4_attach_local(struct ioc4_driver_data *idd) DPRINT_CONFIG(("%s: port_number %d port 0x%p inring 0x%p " "outring 0x%p\n", - __FUNCTION__, + __func__, port_number, (void *)port, (void *)port->ip_inring, (void *)port->ip_outring)); @@ -1317,7 +1317,7 @@ config_port(struct ioc4_port *port, int spiniter = 0; DPRINT_CONFIG(("%s: baud %d byte_size %d stop %d parenb %d parodd %d\n", - __FUNCTION__, baud, byte_size, stop_bits, parenb, parodd)); + __func__, baud, byte_size, stop_bits, parenb, parodd)); if (set_baud(port, baud)) return 1; @@ -1725,7 +1725,7 @@ ioc4_change_speed(struct uart_port *the_port, } baud = uart_get_baud_rate(the_port, new_termios, old_termios, MIN_BAUD_SUPPORTED, MAX_BAUD_SUPPORTED); - DPRINT_CONFIG(("%s: returned baud %d\n", __FUNCTION__, baud)); + DPRINT_CONFIG(("%s: returned baud %d\n", __func__, baud)); /* default is 9600 */ if (!baud) @@ -1765,7 +1765,7 @@ ioc4_change_speed(struct uart_port *the_port, DPRINT_CONFIG(("%s : port 0x%p cflag 0%o " "config_port(baud %d data %d stop %d p enable %d parity %d)," " notification 0x%x\n", - __FUNCTION__, (void *)port, cflag, baud, new_data, new_stop, + __func__, (void *)port, cflag, baud, new_data, new_stop, new_parity_enable, new_parity, the_port->ignore_status_mask)); if ((config_port(port, baud, /* baud */ @@ -2715,7 +2715,7 @@ ioc4_serial_core_attach(struct pci_dev *pdev, int port_type) DPRINT_CONFIG(("%s: attach pdev 0x%p - control 0x%p\n", - __FUNCTION__, pdev, (void *)control)); + __func__, pdev, (void *)control)); if (!control) return -ENODEV; @@ -2734,7 +2734,7 @@ ioc4_serial_core_attach(struct pci_dev *pdev, int port_type) port->ip_all_ports[port_type_idx] = the_port; DPRINT_CONFIG(("%s: attach the_port 0x%p / port 0x%p : type %s\n", - __FUNCTION__, (void *)the_port, + __func__, (void *)the_port, (void *)port, port_type == PROTO_RS232 ? "rs232" : "rs422")); @@ -2752,7 +2752,7 @@ ioc4_serial_core_attach(struct pci_dev *pdev, int port_type) if (uart_add_one_port(u_driver, the_port) < 0) { printk(KERN_WARNING "%s: unable to add port %d bus %d\n", - __FUNCTION__, the_port->line, pdev->bus->number); + __func__, the_port->line, pdev->bus->number); } else { DPRINT_CONFIG( ("IOC4 serial port %d irq = %d, bus %d\n", @@ -2777,7 +2777,7 @@ ioc4_serial_attach_one(struct ioc4_driver_data *idd) int ret = 0; - DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __FUNCTION__, idd->idd_pdev, + DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __func__, idd->idd_pdev, idd->idd_pci_id)); /* PCI-RT does not bring out serial connections. @@ -2806,7 +2806,7 @@ ioc4_serial_attach_one(struct ioc4_driver_data *idd) goto out2; } DPRINT_CONFIG(("%s : mem 0x%p, serial 0x%p\n", - __FUNCTION__, (void *)idd->idd_misc_regs, + __func__, (void *)idd->idd_misc_regs, (void *)serial)); /* Get memory for the new card */ @@ -2858,7 +2858,7 @@ ioc4_serial_attach_one(struct ioc4_driver_data *idd) } else { printk(KERN_WARNING "%s : request_irq fails for IRQ 0x%x\n ", - __FUNCTION__, idd->idd_pdev->irq); + __func__, idd->idd_pdev->irq); } ret = ioc4_attach_local(idd); if (ret) @@ -2911,13 +2911,13 @@ int ioc4_serial_init(void) if ((ret = uart_register_driver(&ioc4_uart_rs232)) < 0) { printk(KERN_WARNING "%s: Couldn't register rs232 IOC4 serial driver\n", - __FUNCTION__); + __func__); return ret; } if ((ret = uart_register_driver(&ioc4_uart_rs422)) < 0) { printk(KERN_WARNING "%s: Couldn't register rs422 IOC4 serial driver\n", - __FUNCTION__); + __func__); return ret; } diff --git a/drivers/serial/jsm/jsm.h b/drivers/serial/jsm/jsm.h index 12c934a1f274..8871aaa3dba6 100644 --- a/drivers/serial/jsm/jsm.h +++ b/drivers/serial/jsm/jsm.h @@ -373,6 +373,7 @@ struct neo_uart_struct { #define PCI_DEVICE_NEO_2DB9PRI_PCI_NAME "Neo 2 - DB9 Universal PCI - Powered Ring Indicator" #define PCI_DEVICE_NEO_2RJ45_PCI_NAME "Neo 2 - RJ45 Universal PCI" #define PCI_DEVICE_NEO_2RJ45PRI_PCI_NAME "Neo 2 - RJ45 Universal PCI - Powered Ring Indicator" +#define PCIE_DEVICE_NEO_IBM_PCI_NAME "Neo 4 - PCI Express - IBM" /* * Our Global Variables. diff --git a/drivers/serial/jsm/jsm_driver.c b/drivers/serial/jsm/jsm_driver.c index 6767ee381cd1..338cf8a08b43 100644 --- a/drivers/serial/jsm/jsm_driver.c +++ b/drivers/serial/jsm/jsm_driver.c @@ -82,7 +82,10 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent) /* store the info for the board we've found */ brd->boardnum = adapter_count++; brd->pci_dev = pdev; - brd->maxports = 2; + if (pdev->device == PCIE_DEVICE_ID_NEO_4_IBM) + brd->maxports = 4; + else + brd->maxports = 2; spin_lock_init(&brd->bd_lock); spin_lock_init(&brd->bd_intr_lock); @@ -208,6 +211,7 @@ static struct pci_device_id jsm_pci_tbl[] = { { PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2DB9PRI), 0, 0, 1 }, { PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2RJ45), 0, 0, 2 }, { PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCI_DEVICE_ID_NEO_2RJ45PRI), 0, 0, 3 }, + { PCI_DEVICE(PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_4_IBM), 0, 0, 4 }, { 0, } }; MODULE_DEVICE_TABLE(pci, jsm_pci_tbl); diff --git a/drivers/serial/kgdboc.c b/drivers/serial/kgdboc.c index 9cf03327386a..eadc1ab6bbce 100644 --- a/drivers/serial/kgdboc.c +++ b/drivers/serial/kgdboc.c @@ -96,12 +96,14 @@ static void cleanup_kgdboc(void) static int kgdboc_get_char(void) { - return kgdb_tty_driver->poll_get_char(kgdb_tty_driver, kgdb_tty_line); + return kgdb_tty_driver->ops->poll_get_char(kgdb_tty_driver, + kgdb_tty_line); } static void kgdboc_put_char(u8 chr) { - kgdb_tty_driver->poll_put_char(kgdb_tty_driver, kgdb_tty_line, chr); + kgdb_tty_driver->ops->poll_put_char(kgdb_tty_driver, + kgdb_tty_line, chr); } static int param_set_kgdboc_var(const char *kmessage, struct kernel_param *kp) diff --git a/drivers/serial/mcfserial.c b/drivers/serial/mcfserial.c index ddd3aa50d4ad..43af40d59b8a 100644 --- a/drivers/serial/mcfserial.c +++ b/drivers/serial/mcfserial.c @@ -1072,18 +1072,6 @@ static int mcfrs_ioctl(struct tty_struct *tty, struct file * file, tty_wait_until_sent(tty, 0); send_break(info, arg ? arg*(HZ/10) : HZ/4); return 0; - case TIOCGSOFTCAR: - error = put_user(C_CLOCAL(tty) ? 1 : 0, - (unsigned long *) arg); - if (error) - return error; - return 0; - case TIOCSSOFTCAR: - get_user(arg, (unsigned long *) arg); - tty->termios->c_cflag = - ((tty->termios->c_cflag & ~CLOCAL) | - (arg ? CLOCAL : 0)); - return 0; case TIOCGSERIAL: if (access_ok(VERIFY_WRITE, (void *) arg, sizeof(struct serial_struct))) @@ -1222,8 +1210,7 @@ static void mcfrs_close(struct tty_struct *tty, struct file * filp) } else #endif shutdown(info); - if (tty->driver->flush_buffer) - tty->driver->flush_buffer(tty); + mcfrs_flush_buffer(tty); tty_ldisc_flush(tty); tty->closing = 0; @@ -1276,6 +1263,8 @@ mcfrs_wait_until_sent(struct tty_struct *tty, int timeout) * Note: we have to use pretty tight timings here to satisfy * the NIST-PCTS. */ + lock_kernel(); + fifo_time = (MCF5272_FIFO_SIZE * HZ * 10) / info->baud; char_time = fifo_time / 5; if (char_time == 0) @@ -1312,6 +1301,7 @@ mcfrs_wait_until_sent(struct tty_struct *tty, int timeout) if (timeout && time_after(jiffies, orig_jiffies + timeout)) break; } + unlock_kernel(); #else /* * For the other coldfire models, assume all data has been sent @@ -1907,7 +1897,7 @@ static struct tty_driver *mcfrs_console_device(struct console *c, int *index) * This is used for console output. */ -void mcfrs_put_char(char ch) +int mcfrs_put_char(char ch) { volatile unsigned char *uartp; unsigned long flags; @@ -1931,7 +1921,7 @@ void mcfrs_put_char(char ch) mcfrs_init_console(); /* try and get it back */ local_irq_restore(flags); - return; + return 1; } diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c index d93b3578c5e2..efc971d9647b 100644 --- a/drivers/serial/mpc52xx_uart.c +++ b/drivers/serial/mpc52xx_uart.c @@ -783,7 +783,9 @@ mpc52xx_uart_int_rx_chars(struct uart_port *port) } } + spin_unlock(&port->lock); tty_flip_buffer_push(tty); + spin_lock(&port->lock); return psc_ops->raw_rx_rdy(port); } @@ -1221,8 +1223,8 @@ static struct of_device_id mpc52xx_uart_of_match[] = { #endif #ifdef CONFIG_PPC_MPC512x { .compatible = "fsl,mpc5121-psc-uart", .data = &mpc512x_psc_ops, }, - {}, #endif + {}, }; static int __devinit diff --git a/drivers/serial/netx-serial.c b/drivers/serial/netx-serial.c index 3123ffeac8ad..81ac9bb4f39b 100644 --- a/drivers/serial/netx-serial.c +++ b/drivers/serial/netx-serial.c @@ -287,6 +287,7 @@ static void netx_set_mctrl(struct uart_port *port, unsigned int mctrl) { unsigned int val; + /* FIXME: Locking needed ? */ if (mctrl & TIOCM_RTS) { val = readl(port->membase + UART_RTS_CR); writel(val | RTS_CR_RTS, port->membase + UART_RTS_CR); diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c index 4ffa2585429a..2b6a013639e6 100644 --- a/drivers/serial/s3c2410.c +++ b/drivers/serial/s3c2410.c @@ -1022,6 +1022,7 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport, struct uart_port *port = &ourport->port; struct s3c2410_uartcfg *cfg; struct resource *res; + int ret; dbg("s3c24xx_serial_init_port: port=%p, platdev=%p\n", port, platdev); @@ -1064,9 +1065,11 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport, port->mapbase = res->start; port->membase = S3C24XX_VA_UART + (res->start - S3C24XX_PA_UART); - port->irq = platform_get_irq(platdev, 0); - if (port->irq < 0) + ret = platform_get_irq(platdev, 0); + if (ret < 0) port->irq = 0; + else + port->irq = ret; ourport->clk = clk_get(&platdev->dev, "uart"); @@ -1093,13 +1096,13 @@ static int s3c24xx_serial_probe(struct platform_device *dev, ourport = &s3c24xx_serial_ports[probe_index]; probe_index++; - dbg("%s: initialising port %p...\n", __FUNCTION__, ourport); + dbg("%s: initialising port %p...\n", __func__, ourport); ret = s3c24xx_serial_init_port(ourport, info, dev); if (ret < 0) goto probe_err; - dbg("%s: adding port\n", __FUNCTION__); + dbg("%s: adding port\n", __func__); uart_add_one_port(&s3c24xx_uart_drv, &ourport->port); platform_set_drvdata(dev, &ourport->port); @@ -1584,7 +1587,7 @@ static int s3c2412_serial_resetport(struct uart_port *port, unsigned long ucon = rd_regl(port, S3C2410_UCON); dbg("%s: port=%p (%08lx), cfg=%p\n", - __FUNCTION__, port, port->mapbase, cfg); + __func__, port, port->mapbase, cfg); /* ensure we don't change the clock settings... */ diff --git a/drivers/serial/sa1100.c b/drivers/serial/sa1100.c index 67b2338913c2..62b38582f5e9 100644 --- a/drivers/serial/sa1100.c +++ b/drivers/serial/sa1100.c @@ -655,7 +655,7 @@ void __init sa1100_register_uart_fns(struct sa1100_port_fns *fns) void __init sa1100_register_uart(int idx, int port) { if (idx >= NR_PORTS) { - printk(KERN_ERR "%s: bad index number %d\n", __FUNCTION__, idx); + printk(KERN_ERR "%s: bad index number %d\n", __func__, idx); return; } @@ -682,7 +682,7 @@ void __init sa1100_register_uart(int idx, int port) break; default: - printk(KERN_ERR "%s: bad port number %d\n", __FUNCTION__, port); + printk(KERN_ERR "%s: bad port number %d\n", __func__, port); } } diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index 977ce820ce30..1e2b9d826f69 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -422,6 +422,7 @@ uart_get_divisor(struct uart_port *port, unsigned int baud) EXPORT_SYMBOL(uart_get_divisor); +/* FIXME: Consistent locking policy */ static void uart_change_speed(struct uart_state *state, struct ktermios *old_termios) { @@ -454,27 +455,30 @@ uart_change_speed(struct uart_state *state, struct ktermios *old_termios) port->ops->set_termios(port, termios, old_termios); } -static inline void +static inline int __uart_put_char(struct uart_port *port, struct circ_buf *circ, unsigned char c) { unsigned long flags; + int ret = 0; if (!circ->buf) - return; + return 0; spin_lock_irqsave(&port->lock, flags); if (uart_circ_chars_free(circ) != 0) { circ->buf[circ->head] = c; circ->head = (circ->head + 1) & (UART_XMIT_SIZE - 1); + ret = 1; } spin_unlock_irqrestore(&port->lock, flags); + return ret; } -static void uart_put_char(struct tty_struct *tty, unsigned char ch) +static int uart_put_char(struct tty_struct *tty, unsigned char ch) { struct uart_state *state = tty->driver_data; - __uart_put_char(state->port, &state->info->xmit, ch); + return __uart_put_char(state->port, &state->info->xmit, ch); } static void uart_flush_chars(struct tty_struct *tty) @@ -528,15 +532,25 @@ uart_write(struct tty_struct *tty, const unsigned char *buf, int count) static int uart_write_room(struct tty_struct *tty) { struct uart_state *state = tty->driver_data; + unsigned long flags; + int ret; - return uart_circ_chars_free(&state->info->xmit); + spin_lock_irqsave(&state->port->lock, flags); + ret = uart_circ_chars_free(&state->info->xmit); + spin_unlock_irqrestore(&state->port->lock, flags); + return ret; } static int uart_chars_in_buffer(struct tty_struct *tty) { struct uart_state *state = tty->driver_data; + unsigned long flags; + int ret; - return uart_circ_chars_pending(&state->info->xmit); + spin_lock_irqsave(&state->port->lock, flags); + ret = uart_circ_chars_pending(&state->info->xmit); + spin_unlock_irqrestore(&state->port->lock, flags); + return ret; } static void uart_flush_buffer(struct tty_struct *tty) @@ -618,6 +632,11 @@ static int uart_get_info(struct uart_state *state, struct serial_struct tmp; memset(&tmp, 0, sizeof(tmp)); + + /* Ensure the state we copy is consistent and no hardware changes + occur as we go */ + mutex_lock(&state->mutex); + tmp.type = port->type; tmp.line = port->line; tmp.port = port->iobase; @@ -637,6 +656,8 @@ static int uart_get_info(struct uart_state *state, tmp.iomem_reg_shift = port->regshift; tmp.iomem_base = (void *)(unsigned long)port->mapbase; + mutex_unlock(&state->mutex); + if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) return -EFAULT; return 0; @@ -914,8 +935,6 @@ static void uart_break_ctl(struct tty_struct *tty, int break_state) struct uart_state *state = tty->driver_data; struct uart_port *port = state->port; - BUG_ON(!kernel_locked()); - mutex_lock(&state->mutex); if (port->type != PORT_UNKNOWN) @@ -1059,7 +1078,7 @@ static int uart_get_count(struct uart_state *state, } /* - * Called via sys_ioctl under the BKL. We can use spin_lock_irq() here. + * Called via sys_ioctl. We can use spin_lock_irq() here. */ static int uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd, @@ -1069,7 +1088,6 @@ uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd, void __user *uarg = (void __user *)arg; int ret = -ENOIOCTLCMD; - BUG_ON(!kernel_locked()); /* * These ioctls don't rely on the hardware to be present. @@ -1140,9 +1158,9 @@ uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd, break; } } - out_up: +out_up: mutex_unlock(&state->mutex); - out: +out: return ret; } @@ -1153,7 +1171,6 @@ static void uart_set_termios(struct tty_struct *tty, unsigned long flags; unsigned int cflag = tty->termios->c_cflag; - BUG_ON(!kernel_locked()); /* * These are the bits that are used to setup various @@ -1165,8 +1182,9 @@ static void uart_set_termios(struct tty_struct *tty, if ((cflag ^ old_termios->c_cflag) == 0 && tty->termios->c_ospeed == old_termios->c_ospeed && tty->termios->c_ispeed == old_termios->c_ispeed && - RELEVANT_IFLAG(tty->termios->c_iflag ^ old_termios->c_iflag) == 0) + RELEVANT_IFLAG(tty->termios->c_iflag ^ old_termios->c_iflag) == 0) { return; + } uart_change_speed(state, old_termios); @@ -1200,7 +1218,6 @@ static void uart_set_termios(struct tty_struct *tty, } spin_unlock_irqrestore(&state->port->lock, flags); } - #if 0 /* * No need to wake up processes in open wait, since they @@ -1316,11 +1333,11 @@ static void uart_wait_until_sent(struct tty_struct *tty, int timeout) struct uart_port *port = state->port; unsigned long char_time, expire; - BUG_ON(!kernel_locked()); - if (port->type == PORT_UNKNOWN || port->fifosize == 0) return; + lock_kernel(); + /* * Set the check interval to be 1/5 of the estimated time to * send a single character, and make it at least 1. The check @@ -1366,6 +1383,7 @@ static void uart_wait_until_sent(struct tty_struct *tty, int timeout) break; } set_current_state(TASK_RUNNING); /* might not be needed */ + unlock_kernel(); } /* @@ -2079,7 +2097,9 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *port) int ret; uart_change_pm(state, 0); + spin_lock_irq(&port->lock); ops->set_mctrl(port, 0); + spin_unlock_irq(&port->lock); ret = ops->startup(port); if (ret == 0) { uart_change_speed(state, NULL); diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c index c2ea5d4df44a..969106187718 100644 --- a/drivers/serial/sh-sci.c +++ b/drivers/serial/sh-sci.c @@ -855,7 +855,7 @@ static int sci_notifier(struct notifier_block *self, printk(KERN_INFO "%s: got a postchange notification " "for cpu %d (old %d, new %d)\n", - __FUNCTION__, freqs->cpu, freqs->old, freqs->new); + __func__, freqs->cpu, freqs->old, freqs->new); } return NOTIFY_OK; diff --git a/drivers/serial/sn_console.c b/drivers/serial/sn_console.c index 41fc61264443..019da2e05f0b 100644 --- a/drivers/serial/sn_console.c +++ b/drivers/serial/sn_console.c @@ -839,7 +839,7 @@ static int __init sn_sal_module_init(void) if (uart_add_one_port(&sal_console_uart, &sal_console_port.sc_port) < 0) { /* error - not sure what I'd do - so I'll do nothing */ - printk(KERN_ERR "%s: unable to add port\n", __FUNCTION__); + printk(KERN_ERR "%s: unable to add port\n", __func__); } /* when this driver is compiled in, the console initialization diff --git a/drivers/serial/sunhv.c b/drivers/serial/sunhv.c index be0fe152891b..145c0281495d 100644 --- a/drivers/serial/sunhv.c +++ b/drivers/serial/sunhv.c @@ -392,7 +392,7 @@ static struct uart_ops sunhv_pops = { static struct uart_driver sunhv_reg = { .owner = THIS_MODULE, - .driver_name = "serial", + .driver_name = "sunhv", .dev_name = "ttyS", .major = TTY_MAJOR, }; diff --git a/drivers/serial/sunsab.c b/drivers/serial/sunsab.c index 543f93741e6f..9ff5b38f3bee 100644 --- a/drivers/serial/sunsab.c +++ b/drivers/serial/sunsab.c @@ -826,7 +826,7 @@ static struct uart_ops sunsab_pops = { static struct uart_driver sunsab_reg = { .owner = THIS_MODULE, - .driver_name = "serial", + .driver_name = "sunsab", .dev_name = "ttyS", .major = TTY_MAJOR, }; diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c index 4e2302d43ab1..03806a935209 100644 --- a/drivers/serial/sunsu.c +++ b/drivers/serial/sunsu.c @@ -1173,7 +1173,7 @@ out: static struct uart_driver sunsu_reg = { .owner = THIS_MODULE, - .driver_name = "serial", + .driver_name = "sunsu", .dev_name = "ttyS", .major = TTY_MAJOR, }; diff --git a/drivers/serial/sunzilog.c b/drivers/serial/sunzilog.c index 90a20a152ebf..7e9fa5ef0eb7 100644 --- a/drivers/serial/sunzilog.c +++ b/drivers/serial/sunzilog.c @@ -1023,7 +1023,7 @@ static struct uart_sunzilog_port *sunzilog_irq_chain; static struct uart_driver sunzilog_reg = { .owner = THIS_MODULE, - .driver_name = "ttyS", + .driver_name = "sunzilog", .dev_name = "ttyS", .major = TTY_MAJOR, }; diff --git a/drivers/serial/uartlite.c b/drivers/serial/uartlite.c index b565d5a37499..b51c24245be4 100644 --- a/drivers/serial/uartlite.c +++ b/drivers/serial/uartlite.c @@ -584,7 +584,7 @@ ulite_of_probe(struct of_device *op, const struct of_device_id *match) const unsigned int *id; int irq, rc; - dev_dbg(&op->dev, "%s(%p, %p)\n", __FUNCTION__, op, match); + dev_dbg(&op->dev, "%s(%p, %p)\n", __func__, op, match); rc = of_address_to_resource(op->node, 0, &res); if (rc) { diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c index 5e4310ccd591..01917c433f17 100644 --- a/drivers/serial/ucc_uart.c +++ b/drivers/serial/ucc_uart.c @@ -215,7 +215,7 @@ static inline dma_addr_t cpu2qe_addr(void *addr, struct uart_qe_port *qe_port) return qe_port->bd_dma_addr + (addr - qe_port->bd_virt); /* something nasty happened */ - printk(KERN_ERR "%s: addr=%p\n", __FUNCTION__, addr); + printk(KERN_ERR "%s: addr=%p\n", __func__, addr); BUG(); return 0; } @@ -234,7 +234,7 @@ static inline void *qe2cpu_addr(dma_addr_t addr, struct uart_qe_port *qe_port) return qe_port->bd_virt + (addr - qe_port->bd_dma_addr); /* something nasty happened */ - printk(KERN_ERR "%s: addr=%x\n", __FUNCTION__, addr); + printk(KERN_ERR "%s: addr=%x\n", __func__, addr); BUG(); return NULL; } |