diff options
Diffstat (limited to 'drivers/spi/amba-pl022.c')
| -rw-r--r-- | drivers/spi/amba-pl022.c | 36 |
1 files changed, 27 insertions, 9 deletions
diff --git a/drivers/spi/amba-pl022.c b/drivers/spi/amba-pl022.c index 5c2b092a915e..5825370bad25 100644 --- a/drivers/spi/amba-pl022.c +++ b/drivers/spi/amba-pl022.c @@ -324,6 +324,7 @@ struct vendor_data { bool unidir; bool extended_cr; bool pl023; + bool loopback; }; /** @@ -660,7 +661,7 @@ static void readwriter(struct pl022 *pl022) { /* - * The FIFO depth is different inbetween primecell variants. + * The FIFO depth is different between primecell variants. * I believe filling in too much in the FIFO might cause * errons in 8bit wide transfers on ARM variants (just 8 words * FIFO, means only 8x8 = 64 bits in FIFO) at least. @@ -721,7 +722,7 @@ static void readwriter(struct pl022 *pl022) * This inner reader takes care of things appearing in the RX * FIFO as we're transmitting. This will happen a lot since the * clock starts running when you put things into the TX FIFO, - * and then things are continously clocked into the RX FIFO. + * and then things are continuously clocked into the RX FIFO. */ while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) && (pl022->rx < pl022->rx_end)) { @@ -841,7 +842,7 @@ static void dma_callback(void *data) unmap_free_dma_scatter(pl022); - /* Update total bytes transfered */ + /* Update total bytes transferred */ msg->actual_length += pl022->cur_transfer->len; if (pl022->cur_transfer->cs_change) pl022->cur_chip-> @@ -1223,7 +1224,7 @@ static irqreturn_t pl022_interrupt_handler(int irq, void *dev_id) "number of bytes on a 16bit bus?)\n", (u32) (pl022->rx - pl022->rx_end)); } - /* Update total bytes transfered */ + /* Update total bytes transferred */ msg->actual_length += pl022->cur_transfer->len; if (pl022->cur_transfer->cs_change) pl022->cur_chip-> @@ -1414,11 +1415,11 @@ static void do_polling_transfer(struct pl022 *pl022) SSP_CR1(pl022->virtbase)); dev_dbg(&pl022->adev->dev, "polling transfer ongoing ...\n"); - /* FIXME: insert a timeout so we don't hang here indefinately */ + /* FIXME: insert a timeout so we don't hang here indefinitely */ while (pl022->tx < pl022->tx_end || pl022->rx < pl022->rx_end) readwriter(pl022); - /* Update total byte transfered */ + /* Update total byte transferred */ message->actual_length += pl022->cur_transfer->len; if (pl022->cur_transfer->cs_change) pl022->cur_chip->cs_control(SSP_CHIP_DESELECT); @@ -1983,7 +1984,7 @@ static int pl022_setup(struct spi_device *spi) SSP_WRITE_BITS(chip->cr0, clk_freq.scr, SSP_CR0_MASK_SCR, 8); /* Loopback is available on all versions except PL023 */ - if (!pl022->vendor->pl023) { + if (pl022->vendor->loopback) { if (spi->mode & SPI_LOOP) tmp = LOOPBACK_ENABLED; else @@ -2128,7 +2129,7 @@ pl022_probe(struct amba_device *adev, const struct amba_id *id) "probe - problem registering spi master\n"); goto err_spi_register; } - dev_dbg(dev, "probe succeded\n"); + dev_dbg(dev, "probe succeeded\n"); /* * Disable the silicon block pclk and any voltage domain and just * power it up and clock it when it's needed @@ -2183,7 +2184,7 @@ pl022_remove(struct amba_device *adev) spi_unregister_master(pl022->master); spi_master_put(pl022->master); amba_set_drvdata(adev, NULL); - dev_dbg(&adev->dev, "remove succeded\n"); + dev_dbg(&adev->dev, "remove succeeded\n"); return 0; } @@ -2233,6 +2234,7 @@ static struct vendor_data vendor_arm = { .unidir = false, .extended_cr = false, .pl023 = false, + .loopback = true, }; @@ -2242,6 +2244,7 @@ static struct vendor_data vendor_st = { .unidir = false, .extended_cr = true, .pl023 = false, + .loopback = true, }; static struct vendor_data vendor_st_pl023 = { @@ -2250,6 +2253,16 @@ static struct vendor_data vendor_st_pl023 = { .unidir = false, .extended_cr = true, .pl023 = true, + .loopback = false, +}; + +static struct vendor_data vendor_db5500_pl023 = { + .fifodepth = 32, + .max_bpw = 32, + .unidir = false, + .extended_cr = true, + .pl023 = true, + .loopback = true, }; static struct amba_id pl022_ids[] = { @@ -2283,6 +2296,11 @@ static struct amba_id pl022_ids[] = { .mask = 0xffffffff, .data = &vendor_st_pl023, }, + { + .id = 0x10080023, + .mask = 0xffffffff, + .data = &vendor_db5500_pl023, + }, { 0, 0 }, }; |