1 files changed, 141 insertions, 0 deletions

diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
new file mode 100644
index 000000000000..b1449ad67fc0
--- /dev/null
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -0,0 +1,141 @@
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include "tsens.h"
+
+#define S0_ST_ADDR		0x1030
+#define SN_ADDR_OFFSET		0x4
+#define SN_ST_TEMP_MASK		0x3ff
+#define CAL_DEGC_PT1		30
+#define CAL_DEGC_PT2		120
+#define SLOPE_FACTOR		1000
+#define SLOPE_DEFAULT		3200
+
+char *qfprom_read(struct device *dev, const char *cname)
+{
+	struct nvmem_cell *cell;
+	ssize_t data;
+	char *ret;
+
+	cell = nvmem_cell_get(dev, cname);
+	if (IS_ERR(cell))
+		return ERR_CAST(cell);
+
+	ret = nvmem_cell_read(cell, &data);
+	nvmem_cell_put(cell);
+
+	return ret;
+}
+
+/*
+ * Use this function on devices where slope and offset calculations
+ * depend on calibration data read from qfprom. On others the slope
+ * and offset values are derived from tz->tzp->slope and tz->tzp->offset
+ * resp.
+ */
+void compute_intercept_slope(struct tsens_device *tmdev, u32 *p1,
+			     u32 *p2, u32 mode)
+{
+	int i;
+	int num, den;
+
+	for (i = 0; i < tmdev->num_sensors; i++) {
+		dev_dbg(tmdev->dev,
+			"sensor%d - data_point1:%#x data_point2:%#x\n",
+			i, p1[i], p2[i]);
+
+		tmdev->sensor[i].slope = SLOPE_DEFAULT;
+		if (mode == TWO_PT_CALIB) {
+			/*
+			 * slope (m) = adc_code2 - adc_code1 (y2 - y1)/
+			 *	temp_120_degc - temp_30_degc (x2 - x1)
+			 */
+			num = p2[i] - p1[i];
+			num *= SLOPE_FACTOR;
+			den = CAL_DEGC_PT2 - CAL_DEGC_PT1;
+			tmdev->sensor[i].slope = num / den;
+		}
+
+		tmdev->sensor[i].offset = (p1[i] * SLOPE_FACTOR) -
+				(CAL_DEGC_PT1 *
+				tmdev->sensor[i].slope);
+		dev_dbg(tmdev->dev, "offset:%d\n", tmdev->sensor[i].offset);
+	}
+}
+
+static inline int code_to_degc(u32 adc_code, const struct tsens_sensor *s)
+{
+	int degc, num, den;
+
+	num = (adc_code * SLOPE_FACTOR) - s->offset;
+	den = s->slope;
+
+	if (num > 0)
+		degc = num + (den / 2);
+	else if (num < 0)
+		degc = num - (den / 2);
+	else
+		degc = num;
+
+	degc /= den;
+
+	return degc;
+}
+
+int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
+{
+	struct tsens_sensor *s = &tmdev->sensor[id];
+	u32 code;
+	unsigned int sensor_addr;
+	int last_temp = 0, ret;
+
+	sensor_addr = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
+	ret = regmap_read(tmdev->map, sensor_addr, &code);
+	if (ret)
+		return ret;
+	last_temp = code & SN_ST_TEMP_MASK;
+
+	*temp = code_to_degc(last_temp, s) * 1000;
+
+	return 0;
+}
+
+static const struct regmap_config tsens_config = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+};
+
+int __init init_common(struct tsens_device *tmdev)
+{
+	void __iomem *base;
+
+	base = of_iomap(tmdev->dev->of_node, 0);
+	if (!base)
+		return -EINVAL;
+
+	tmdev->map = devm_regmap_init_mmio(tmdev->dev, base, &tsens_config);
+	if (IS_ERR(tmdev->map)) {
+		iounmap(base);
+		return PTR_ERR(tmdev->map);
+	}
+
+	return 0;
+}