diff options
Diffstat (limited to 'drivers/tty/Kconfig')
| -rw-r--r-- | drivers/tty/Kconfig | 321 |
1 files changed, 321 insertions, 0 deletions
diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig new file mode 100644 index 000000000000..3fd7199301b6 --- /dev/null +++ b/drivers/tty/Kconfig @@ -0,0 +1,321 @@ +config VT + bool "Virtual terminal" if EXPERT + depends on !S390 + select INPUT + default y + ---help--- + If you say Y here, you will get support for terminal devices with + display and keyboard devices. These are called "virtual" because you + can run several virtual terminals (also called virtual consoles) on + one physical terminal. This is rather useful, for example one + virtual terminal can collect system messages and warnings, another + one can be used for a text-mode user session, and a third could run + an X session, all in parallel. Switching between virtual terminals + is done with certain key combinations, usually Alt-<function key>. + + The setterm command ("man setterm") can be used to change the + properties (such as colors or beeping) of a virtual terminal. The + man page console_codes(4) ("man console_codes") contains the special + character sequences that can be used to change those properties + directly. The fonts used on virtual terminals can be changed with + the setfont ("man setfont") command and the key bindings are defined + with the loadkeys ("man loadkeys") command. + + You need at least one virtual terminal device in order to make use + of your keyboard and monitor. Therefore, only people configuring an + embedded system would want to say N here in order to save some + memory; the only way to log into such a system is then via a serial + or network connection. + + If unsure, say Y, or else you won't be able to do much with your new + shiny Linux system :-) + +config CONSOLE_TRANSLATIONS + depends on VT + default y + bool "Enable character translations in console" if EXPERT + ---help--- + This enables support for font mapping and Unicode translation + on virtual consoles. + +config VT_CONSOLE + bool "Support for console on virtual terminal" if EXPERT + depends on VT + default y + ---help--- + The system console is the device which receives all kernel messages + and warnings and which allows logins in single user mode. If you + answer Y here, a virtual terminal (the device used to interact with + a physical terminal) can be used as system console. This is the most + common mode of operations, so you should say Y here unless you want + the kernel messages be output only to a serial port (in which case + you should say Y to "Console on serial port", below). + + If you do say Y here, by default the currently visible virtual + terminal (/dev/tty0) will be used as system console. You can change + that with a kernel command line option such as "console=tty3" which + would use the third virtual terminal as system console. (Try "man + bootparam" or see the documentation of your boot loader (lilo or + loadlin) about how to pass options to the kernel at boot time.) + + If unsure, say Y. + +config HW_CONSOLE + bool + depends on VT && !S390 && !UML + default y + +config VT_HW_CONSOLE_BINDING + bool "Support for binding and unbinding console drivers" + depends on HW_CONSOLE + default n + ---help--- + The virtual terminal is the device that interacts with the physical + terminal through console drivers. On these systems, at least one + console driver is loaded. In other configurations, additional console + drivers may be enabled, such as the framebuffer console. If more than + 1 console driver is enabled, setting this to 'y' will allow you to + select the console driver that will serve as the backend for the + virtual terminals. + + See <file:Documentation/console/console.txt> for more + information. For framebuffer console users, please refer to + <file:Documentation/fb/fbcon.txt>. + +config UNIX98_PTYS + bool "Unix98 PTY support" if EXPERT + default y + ---help--- + A pseudo terminal (PTY) is a software device consisting of two + halves: a master and a slave. The slave device behaves identical to + a physical terminal; the master device is used by a process to + read data from and write data to the slave, thereby emulating a + terminal. Typical programs for the master side are telnet servers + and xterms. + + Linux has traditionally used the BSD-like names /dev/ptyxx for + masters and /dev/ttyxx for slaves of pseudo terminals. This scheme + has a number of problems. The GNU C library glibc 2.1 and later, + however, supports the Unix98 naming standard: in order to acquire a + pseudo terminal, a process opens /dev/ptmx; the number of the pseudo + terminal is then made available to the process and the pseudo + terminal slave can be accessed as /dev/pts/<number>. What was + traditionally /dev/ttyp2 will then be /dev/pts/2, for example. + + All modern Linux systems use the Unix98 ptys. Say Y unless + you're on an embedded system and want to conserve memory. + +config DEVPTS_MULTIPLE_INSTANCES + bool "Support multiple instances of devpts" + depends on UNIX98_PTYS + default n + ---help--- + Enable support for multiple instances of devpts filesystem. + If you want to have isolated PTY namespaces (eg: in containers), + say Y here. Otherwise, say N. If enabled, each mount of devpts + filesystem with the '-o newinstance' option will create an + independent PTY namespace. + +config LEGACY_PTYS + bool "Legacy (BSD) PTY support" + default y + ---help--- + A pseudo terminal (PTY) is a software device consisting of two + halves: a master and a slave. The slave device behaves identical to + a physical terminal; the master device is used by a process to + read data from and write data to the slave, thereby emulating a + terminal. Typical programs for the master side are telnet servers + and xterms. + + Linux has traditionally used the BSD-like names /dev/ptyxx + for masters and /dev/ttyxx for slaves of pseudo + terminals. This scheme has a number of problems, including + security. This option enables these legacy devices; on most + systems, it is safe to say N. + + +config LEGACY_PTY_COUNT + int "Maximum number of legacy PTY in use" + depends on LEGACY_PTYS + range 0 256 + default "256" + ---help--- + The maximum number of legacy PTYs that can be used at any one time. + The default is 256, and should be more than enough. Embedded + systems may want to reduce this to save memory. + + When not in use, each legacy PTY occupies 12 bytes on 32-bit + architectures and 24 bytes on 64-bit architectures. + +config BFIN_JTAG_COMM + tristate "Blackfin JTAG Communication" + depends on BLACKFIN + help + Add support for emulating a TTY device over the Blackfin JTAG. + + To compile this driver as a module, choose M here: the + module will be called bfin_jtag_comm. + +config BFIN_JTAG_COMM_CONSOLE + bool "Console on Blackfin JTAG" + depends on BFIN_JTAG_COMM=y + +config SERIAL_NONSTANDARD + bool "Non-standard serial port support" + depends on HAS_IOMEM + ---help--- + Say Y here if you have any non-standard serial boards -- boards + which aren't supported using the standard "dumb" serial driver. + This includes intelligent serial boards such as Cyclades, + Digiboards, etc. These are usually used for systems that need many + serial ports because they serve many terminals or dial-in + connections. + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about non-standard serial boards. + + Most people can say N here. + +config ROCKETPORT + tristate "Comtrol RocketPort support" + depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI) + help + This driver supports Comtrol RocketPort and RocketModem PCI boards. + These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or + modems. For information about the RocketPort/RocketModem boards + and this driver read <file:Documentation/serial/rocket.txt>. + + To compile this driver as a module, choose M here: the + module will be called rocket. + + If you want to compile this driver into the kernel, say Y here. If + you don't have a Comtrol RocketPort/RocketModem card installed, say N. + +config CYCLADES + tristate "Cyclades async mux support" + depends on SERIAL_NONSTANDARD && (PCI || ISA) + select FW_LOADER + ---help--- + This driver supports Cyclades Z and Y multiserial boards. + You would need something like this to connect more than two modems to + your Linux box, for instance in order to become a dial-in server. + + For information about the Cyclades-Z card, read + <file:Documentation/serial/README.cycladesZ>. + + To compile this driver as a module, choose M here: the + module will be called cyclades. + + If you haven't heard about it, it's safe to say N. + +config CYZ_INTR + bool "Cyclades-Z interrupt mode operation (EXPERIMENTAL)" + depends on EXPERIMENTAL && CYCLADES + help + The Cyclades-Z family of multiport cards allows 2 (two) driver op + modes: polling and interrupt. In polling mode, the driver will check + the status of the Cyclades-Z ports every certain amount of time + (which is called polling cycle and is configurable). In interrupt + mode, it will use an interrupt line (IRQ) in order to check the + status of the Cyclades-Z ports. The default op mode is polling. If + unsure, say N. + +config MOXA_INTELLIO + tristate "Moxa Intellio support" + depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI) + select FW_LOADER + help + Say Y here if you have a Moxa Intellio multiport serial card. + + To compile this driver as a module, choose M here: the + module will be called moxa. + +config MOXA_SMARTIO + tristate "Moxa SmartIO support v. 2.0" + depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA) + help + Say Y here if you have a Moxa SmartIO multiport serial card and/or + want to help develop a new version of this driver. + + This is upgraded (1.9.1) driver from original Moxa drivers with + changes finally resulting in PCI probing. + + This driver can also be built as a module. The module will be called + mxser. If you want to do that, say M here. + +config SYNCLINK + tristate "Microgate SyncLink card support" + depends on SERIAL_NONSTANDARD && PCI && ISA_DMA_API + help + Provides support for the SyncLink ISA and PCI multiprotocol serial + adapters. These adapters support asynchronous and HDLC bit + synchronous communication up to 10Mbps (PCI adapter). + + This driver can only be built as a module ( = code which can be + inserted in and removed from the running kernel whenever you want). + The module will be called synclink. If you want to do that, say M + here. + +config SYNCLINKMP + tristate "SyncLink Multiport support" + depends on SERIAL_NONSTANDARD && PCI + help + Enable support for the SyncLink Multiport (2 or 4 ports) + serial adapter, running asynchronous and HDLC communications up + to 2.048Mbps. Each ports is independently selectable for + RS-232, V.35, RS-449, RS-530, and X.21 + + This driver may be built as a module ( = code which can be + inserted in and removed from the running kernel whenever you want). + The module will be called synclinkmp. If you want to do that, say M + here. + +config SYNCLINK_GT + tristate "SyncLink GT/AC support" + depends on SERIAL_NONSTANDARD && PCI + help + Support for SyncLink GT and SyncLink AC families of + synchronous and asynchronous serial adapters + manufactured by Microgate Systems, Ltd. (www.microgate.com) + +config NOZOMI + tristate "HSDPA Broadband Wireless Data Card - Globe Trotter" + depends on PCI && EXPERIMENTAL + help + If you have a HSDPA driver Broadband Wireless Data Card - + Globe Trotter PCMCIA card, say Y here. + + To compile this driver as a module, choose M here, the module + will be called nozomi. + +config ISI + tristate "Multi-Tech multiport card support (EXPERIMENTAL)" + depends on SERIAL_NONSTANDARD && PCI + select FW_LOADER + help + This is a driver for the Multi-Tech cards which provide several + serial ports. The driver is experimental and can currently only be + built as a module. The module will be called isicom. + If you want to do that, choose M here. + +config N_HDLC + tristate "HDLC line discipline support" + depends on SERIAL_NONSTANDARD + help + Allows synchronous HDLC communications with tty device drivers that + support synchronous HDLC such as the Microgate SyncLink adapter. + + This driver can be built as a module ( = code which can be + inserted in and removed from the running kernel whenever you want). + The module will be called n_hdlc. If you want to do that, say M + here. + +config N_GSM + tristate "GSM MUX line discipline support (EXPERIMENTAL)" + depends on EXPERIMENTAL + depends on NET + help + This line discipline provides support for the GSM MUX protocol and + presents the mux as a set of 61 individual tty devices. + |