1 files changed, 69 insertions, 5 deletions

diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
index 48731d0bab35..21fe1a314313 100644
--- a/drivers/usb/chipidea/host.c
+++ b/drivers/usb/chipidea/host.c
@@ -33,6 +33,7 @@
 #include "host.h"
 
 static struct hc_driver __read_mostly ci_ehci_hc_driver;
+static int (*orig_bus_suspend)(struct usb_hcd *hcd);
 
 struct ehci_ci_priv {
 	struct regulator *reg_vbus;
@@ -43,11 +44,10 @@ static int ehci_ci_portpower(struct usb_hcd *hcd, int portnum, bool enable)
 	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
 	struct ehci_ci_priv *priv = (struct ehci_ci_priv *)ehci->priv;
 	struct device *dev = hcd->self.controller;
-	struct ci_hdrc *ci = dev_get_drvdata(dev);
 	int ret = 0;
 	int port = HCS_N_PORTS(ehci->hcs_params);
 
-	if (priv->reg_vbus && !ci_otg_is_fsm_mode(ci)) {
+	if (priv->reg_vbus) {
 		if (port > 1) {
 			dev_warn(dev,
 				"Not support multi-port regulator control\n");
@@ -113,12 +113,23 @@ static int host_start(struct ci_hdrc *ci)
 	priv = (struct ehci_ci_priv *)ehci->priv;
 	priv->reg_vbus = NULL;
 
-	if (ci->platdata->reg_vbus)
-		priv->reg_vbus = ci->platdata->reg_vbus;
+	if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci)) {
+		if (ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON) {
+			ret = regulator_enable(ci->platdata->reg_vbus);
+			if (ret) {
+				dev_err(ci->dev,
+				"Failed to enable vbus regulator, ret=%d\n",
+									ret);
+				goto put_hcd;
+			}
+		} else {
+			priv->reg_vbus = ci->platdata->reg_vbus;
+		}
+	}
 
 	ret = usb_add_hcd(hcd, 0, 0);
 	if (ret) {
-		goto put_hcd;
+		goto disable_reg;
 	} else {
 		struct usb_otg *otg = &ci->otg;
 
@@ -133,8 +144,15 @@ static int host_start(struct ci_hdrc *ci)
 	if (ci->platdata->flags & CI_HDRC_DISABLE_STREAMING)
 		hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
 
+	if (ci->platdata->flags & CI_HDRC_FORCE_FULLSPEED)
+		hw_write(ci, OP_PORTSC, PORTSC_PFSC, PORTSC_PFSC);
+
 	return ret;
 
+disable_reg:
+	if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) &&
+			(ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON))
+		regulator_disable(ci->platdata->reg_vbus);
 put_hcd:
 	usb_put_hcd(hcd);
 
@@ -148,6 +166,9 @@ static void host_stop(struct ci_hdrc *ci)
 	if (hcd) {
 		usb_remove_hcd(hcd);
 		usb_put_hcd(hcd);
+		if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) &&
+			(ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON))
+				regulator_disable(ci->platdata->reg_vbus);
 	}
 }
 
@@ -158,6 +179,47 @@ void ci_hdrc_host_destroy(struct ci_hdrc *ci)
 		host_stop(ci);
 }
 
+static int ci_ehci_bus_suspend(struct usb_hcd *hcd)
+{
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	int port;
+	u32 tmp;
+
+	int ret = orig_bus_suspend(hcd);
+
+	if (ret)
+		return ret;
+
+	port = HCS_N_PORTS(ehci->hcs_params);
+	while (port--) {
+		u32 __iomem *reg = &ehci->regs->port_status[port];
+		u32 portsc = ehci_readl(ehci, reg);
+
+		if (portsc & PORT_CONNECT) {
+			/*
+			 * For chipidea, the resume signal will be ended
+			 * automatically, so for remote wakeup case, the
+			 * usbcmd.rs may not be set before the resume has
+			 * ended if other resume paths consumes too much
+			 * time (~24ms), in that case, the SOF will not
+			 * send out within 3ms after resume ends, then the
+			 * high speed device will enter full speed mode.
+			 */
+
+			tmp = ehci_readl(ehci, &ehci->regs->command);
+			tmp |= CMD_RUN;
+			ehci_writel(ehci, tmp, &ehci->regs->command);
+			/*
+			 * It needs a short delay between set RS bit and PHCD.
+			 */
+			usleep_range(150, 200);
+			break;
+		}
+	}
+
+	return 0;
+}
+
 int ci_hdrc_host_init(struct ci_hdrc *ci)
 {
 	struct ci_role_driver *rdrv;
@@ -176,6 +238,8 @@ int ci_hdrc_host_init(struct ci_hdrc *ci)
 	ci->roles[CI_ROLE_HOST] = rdrv;
 
 	ehci_init_driver(&ci_ehci_hc_driver, &ehci_ci_overrides);
+	orig_bus_suspend = ci_ehci_hc_driver.bus_suspend;
+	ci_ehci_hc_driver.bus_suspend = ci_ehci_bus_suspend;
 
 	return 0;
 }