1 files changed, 217 insertions, 148 deletions

diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index ec70df7aba17..58fdfad96b4d 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -100,6 +100,23 @@ int dwc3_gadget_set_link_state(struct dwc3 *dwc, enum dwc3_link_state state)
 	int		retries = 10000;
 	u32		reg;
 
+	/*
+	 * Wait until device controller is ready. Only applies to 1.94a and
+	 * later RTL.
+	 */
+	if (dwc->revision >= DWC3_REVISION_194A) {
+		while (--retries) {
+			reg = dwc3_readl(dwc->regs, DWC3_DSTS);
+			if (reg & DWC3_DSTS_DCNRD)
+				udelay(5);
+			else
+				break;
+		}
+
+		if (retries <= 0)
+			return -ETIMEDOUT;
+	}
+
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	reg &= ~DWC3_DCTL_ULSTCHNGREQ_MASK;
 
@@ -107,7 +124,15 @@ int dwc3_gadget_set_link_state(struct dwc3 *dwc, enum dwc3_link_state state)
 	reg |= DWC3_DCTL_ULSTCHNGREQ(state);
 	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
 
+	/*
+	 * The following code is racy when called from dwc3_gadget_wakeup,
+	 * and is not needed, at least on newer versions
+	 */
+	if (dwc->revision >= DWC3_REVISION_194A)
+		return 0;
+
 	/* wait for a change in DSTS */
+	retries = 10000;
 	while (--retries) {
 		reg = dwc3_readl(dwc->regs, DWC3_DSTS);
 
@@ -265,8 +290,8 @@ static const char *dwc3_gadget_ep_cmd_string(u8 cmd)
 		return "Clear Stall";
 	case DWC3_DEPCMD_SETSTALL:
 		return "Set Stall";
-	case DWC3_DEPCMD_GETSEQNUMBER:
-		return "Get Data Sequence Number";
+	case DWC3_DEPCMD_GETEPSTATE:
+		return "Get Endpoint State";
 	case DWC3_DEPCMD_SETTRANSFRESOURCE:
 		return "Set Endpoint Transfer Resource";
 	case DWC3_DEPCMD_SETEPCONFIG:
@@ -414,7 +439,7 @@ static int dwc3_gadget_set_ep_config(struct dwc3 *dwc, struct dwc3_ep *dep,
 
 	params.param0 = DWC3_DEPCFG_EP_TYPE(usb_endpoint_type(desc))
 		| DWC3_DEPCFG_MAX_PACKET_SIZE(usb_endpoint_maxp(desc))
-		| DWC3_DEPCFG_BURST_SIZE(dep->endpoint.maxburst);
+		| DWC3_DEPCFG_BURST_SIZE(dep->endpoint.maxburst - 1);
 
 	params.param1 = DWC3_DEPCFG_XFER_COMPLETE_EN
 		| DWC3_DEPCFG_XFER_NOT_READY_EN;
@@ -530,9 +555,37 @@ static void dwc3_remove_requests(struct dwc3 *dwc, struct dwc3_ep *dep)
 {
 	struct dwc3_request		*req;
 
-	if (!list_empty(&dep->req_queued))
+	if (!list_empty(&dep->req_queued)) {
 		dwc3_stop_active_transfer(dwc, dep->number);
 
+		/*
+		 * NOTICE: We are violating what the Databook says about the
+		 * EndTransfer command. Ideally we would _always_ wait for the
+		 * EndTransfer Command Completion IRQ, but that's causing too
+		 * much trouble synchronizing between us and gadget driver.
+		 *
+		 * We have discussed this with the IP Provider and it was
+		 * suggested to giveback all requests here, but give HW some
+		 * extra time to synchronize with the interconnect. We're using
+		 * an arbitraty 100us delay for that.
+		 *
+		 * Note also that a similar handling was tested by Synopsys
+		 * (thanks a lot Paul) and nothing bad has come out of it.
+		 * In short, what we're doing is:
+		 *
+		 * - Issue EndTransfer WITH CMDIOC bit set
+		 * - Wait 100us
+		 * - giveback all requests to gadget driver
+		 */
+		udelay(100);
+
+		while (!list_empty(&dep->req_queued)) {
+			req = next_request(&dep->req_queued);
+
+			dwc3_gadget_giveback(dep, req, -ESHUTDOWN);
+		}
+	}
+
 	while (!list_empty(&dep->request_list)) {
 		req = next_request(&dep->request_list);
 
@@ -741,8 +794,7 @@ static void dwc3_prepare_one_trb(struct dwc3_ep *dep,
 	case USB_ENDPOINT_XFER_ISOC:
 		trb->ctrl = DWC3_TRBCTL_ISOCHRONOUS_FIRST;
 
-		/* IOC every DWC3_TRB_NUM / 4 so we can refill */
-		if (!(cur_slot % (DWC3_TRB_NUM / 4)))
+		if (!req->request.no_interrupt)
 			trb->ctrl |= DWC3_TRB_CTRL_IOC;
 		break;
 
@@ -958,14 +1010,42 @@ static int __dwc3_gadget_kick_transfer(struct dwc3_ep *dep, u16 cmd_param,
 	dep->flags |= DWC3_EP_BUSY;
 
 	if (start_new) {
-		dep->res_trans_idx = dwc3_gadget_ep_get_transfer_index(dwc,
+		dep->resource_index = dwc3_gadget_ep_get_transfer_index(dwc,
 				dep->number);
-		WARN_ON_ONCE(!dep->res_trans_idx);
+		WARN_ON_ONCE(!dep->resource_index);
 	}
 
 	return 0;
 }
 
+static void __dwc3_gadget_start_isoc(struct dwc3 *dwc,
+		struct dwc3_ep *dep, u32 cur_uf)
+{
+	u32 uf;
+
+	if (list_empty(&dep->request_list)) {
+		dev_vdbg(dwc->dev, "ISOC ep %s run out for requests.\n",
+			dep->name);
+		return;
+	}
+
+	/* 4 micro frames in the future */
+	uf = cur_uf + dep->interval * 4;
+
+	__dwc3_gadget_kick_transfer(dep, uf, 1);
+}
+
+static void dwc3_gadget_start_isoc(struct dwc3 *dwc,
+		struct dwc3_ep *dep, const struct dwc3_event_depevt *event)
+{
+	u32 cur_uf, mask;
+
+	mask = ~(dep->interval - 1);
+	cur_uf = event->parameters & mask;
+
+	__dwc3_gadget_start_isoc(dwc, dep, cur_uf);
+}
+
 static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
 {
 	struct dwc3		*dwc = dep->dwc;
@@ -995,11 +1075,8 @@ static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
 
 	list_add_tail(&req->list, &dep->request_list);
 
-	if (usb_endpoint_xfer_isoc(dep->endpoint.desc) && (dep->flags & DWC3_EP_BUSY))
-		dep->flags |= DWC3_EP_PENDING_REQUEST;
-
 	/*
-	 * There are two special cases:
+	 * There are a few special cases:
 	 *
 	 * 1. XferNotReady with empty list of requests. We need to kick the
 	 *    transfer here in that situation, otherwise we will be NAKing
@@ -1008,31 +1085,46 @@ static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
 	 *    able to receive the data until the next request is queued.
 	 *    The following code is handling exactly that.
 	 *
-	 * 2. XferInProgress on Isoc EP with an active transfer. We need to
-	 *    kick the transfer here after queuing a request, otherwise the
-	 *    core may not see the modified TRB(s).
 	 */
 	if (dep->flags & DWC3_EP_PENDING_REQUEST) {
 		int	ret;
-		int	start_trans = 1;
-		u8	trans_idx = dep->res_trans_idx;
 
-		if (usb_endpoint_xfer_isoc(dep->endpoint.desc) &&
-				(dep->flags & DWC3_EP_BUSY)) {
-			start_trans = 0;
-			WARN_ON_ONCE(!trans_idx);
-		} else {
-			trans_idx = 0;
+		ret = __dwc3_gadget_kick_transfer(dep, 0, true);
+		if (ret && ret != -EBUSY) {
+			struct dwc3	*dwc = dep->dwc;
+
+			dev_dbg(dwc->dev, "%s: failed to kick transfers\n",
+					dep->name);
 		}
+	}
 
-		ret = __dwc3_gadget_kick_transfer(dep, trans_idx, start_trans);
+	/*
+	 * 2. XferInProgress on Isoc EP with an active transfer. We need to
+	 *    kick the transfer here after queuing a request, otherwise the
+	 *    core may not see the modified TRB(s).
+	 */
+	if (usb_endpoint_xfer_isoc(dep->endpoint.desc) &&
+			(dep->flags & DWC3_EP_BUSY)) {
+		WARN_ON_ONCE(!dep->resource_index);
+		ret = __dwc3_gadget_kick_transfer(dep, dep->resource_index,
+				false);
 		if (ret && ret != -EBUSY) {
 			struct dwc3	*dwc = dep->dwc;
 
 			dev_dbg(dwc->dev, "%s: failed to kick transfers\n",
 					dep->name);
 		}
-	};
+	}
+
+	/*
+	 * 3. Missed ISOC Handling. We need to start isoc transfer on the saved
+	 * uframe number.
+	 */
+	if (usb_endpoint_xfer_isoc(dep->endpoint.desc) &&
+		(dep->flags & DWC3_EP_MISSED_ISOC)) {
+			__dwc3_gadget_start_isoc(dwc, dep, dep->current_uf);
+			dep->flags &= ~DWC3_EP_MISSED_ISOC;
+	}
 
 	return 0;
 }
@@ -1118,15 +1210,6 @@ int __dwc3_gadget_ep_set_halt(struct dwc3_ep *dep, int value)
 	memset(&params, 0x00, sizeof(params));
 
 	if (value) {
-		if (dep->number == 0 || dep->number == 1) {
-			/*
-			 * Whenever EP0 is stalled, we will restart
-			 * the state machine, thus moving back to
-			 * Setup Phase
-			 */
-			dwc->ep0state = EP0_SETUP_PHASE;
-		}
-
 		ret = dwc3_send_gadget_ep_cmd(dwc, dep->number,
 			DWC3_DEPCMD_SETSTALL, &params);
 		if (ret)
@@ -1186,7 +1269,10 @@ static int dwc3_gadget_ep_set_wedge(struct usb_ep *ep)
 	dep->flags |= DWC3_EP_WEDGE;
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
-	return dwc3_gadget_ep_set_halt(ep, 1);
+	if (dep->number == 0 || dep->number == 1)
+		return dwc3_gadget_ep0_set_halt(ep, 1);
+	else
+		return dwc3_gadget_ep_set_halt(ep, 1);
 }
 
 /* -------------------------------------------------------------------------- */
@@ -1204,7 +1290,7 @@ static const struct usb_ep_ops dwc3_gadget_ep0_ops = {
 	.free_request	= dwc3_gadget_ep_free_request,
 	.queue		= dwc3_gadget_ep0_queue,
 	.dequeue	= dwc3_gadget_ep_dequeue,
-	.set_halt	= dwc3_gadget_ep_set_halt,
+	.set_halt	= dwc3_gadget_ep0_set_halt,
 	.set_wedge	= dwc3_gadget_ep_set_wedge,
 };
 
@@ -1280,9 +1366,13 @@ static int dwc3_gadget_wakeup(struct usb_gadget *g)
 		goto out;
 	}
 
-	/* write zeroes to Link Change Request */
-	reg &= ~DWC3_DCTL_ULSTCHNGREQ_MASK;
-	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+	/* Recent versions do this automatically */
+	if (dwc->revision < DWC3_REVISION_194A) {
+		/* write zeroes to Link Change Request */
+		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+		reg &= ~DWC3_DCTL_ULSTCHNGREQ_MASK;
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+	}
 
 	/* poll until Link State changes to ON */
 	timeout = jiffies + msecs_to_jiffies(100);
@@ -1319,16 +1409,21 @@ static int dwc3_gadget_set_selfpowered(struct usb_gadget *g,
 	return 0;
 }
 
-static void dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on)
+static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on)
 {
 	u32			reg;
 	u32			timeout = 500;
 
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	if (is_on) {
-		reg &= ~DWC3_DCTL_TRGTULST_MASK;
-		reg |= (DWC3_DCTL_RUN_STOP
-				| DWC3_DCTL_TRGTULST_RX_DET);
+		if (dwc->revision <= DWC3_REVISION_187A) {
+			reg &= ~DWC3_DCTL_TRGTULST_MASK;
+			reg |= DWC3_DCTL_TRGTULST_RX_DET;
+		}
+
+		if (dwc->revision >= DWC3_REVISION_194A)
+			reg &= ~DWC3_DCTL_KEEP_CONNECT;
+		reg |= DWC3_DCTL_RUN_STOP;
 	} else {
 		reg &= ~DWC3_DCTL_RUN_STOP;
 	}
@@ -1346,7 +1441,7 @@ static void dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on)
 		}
 		timeout--;
 		if (!timeout)
-			break;
+			return -ETIMEDOUT;
 		udelay(1);
 	} while (1);
 
@@ -1354,20 +1449,23 @@ static void dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on)
 			dwc->gadget_driver
 			? dwc->gadget_driver->function : "no-function",
 			is_on ? "connect" : "disconnect");
+
+	return 0;
 }
 
 static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
 {
 	struct dwc3		*dwc = gadget_to_dwc(g);
 	unsigned long		flags;
+	int			ret;
 
 	is_on = !!is_on;
 
 	spin_lock_irqsave(&dwc->lock, flags);
-	dwc3_gadget_run_stop(dwc, is_on);
+	ret = dwc3_gadget_run_stop(dwc, is_on);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
-	return 0;
+	return ret;
 }
 
 static int dwc3_gadget_start(struct usb_gadget *g,
@@ -1468,6 +1566,7 @@ static int dwc3_gadget_stop(struct usb_gadget *g,
 
 	return 0;
 }
+
 static const struct usb_gadget_ops dwc3_gadget_ops = {
 	.get_frame		= dwc3_gadget_get_frame,
 	.wakeup			= dwc3_gadget_wakeup,
@@ -1558,6 +1657,7 @@ static int dwc3_cleanup_done_reqs(struct dwc3 *dwc, struct dwc3_ep *dep,
 	struct dwc3_trb		*trb;
 	unsigned int		count;
 	unsigned int		s_pkt = 0;
+	unsigned int		trb_status;
 
 	do {
 		req = next_request(&dep->req_queued);
@@ -1583,9 +1683,18 @@ static int dwc3_cleanup_done_reqs(struct dwc3 *dwc, struct dwc3_ep *dep,
 
 		if (dep->direction) {
 			if (count) {
-				dev_err(dwc->dev, "incomplete IN transfer %s\n",
-						dep->name);
-				status = -ECONNRESET;
+				trb_status = DWC3_TRB_SIZE_TRBSTS(trb->size);
+				if (trb_status == DWC3_TRBSTS_MISSED_ISOC) {
+					dev_dbg(dwc->dev, "incomplete IN transfer %s\n",
+							dep->name);
+					dep->current_uf = event->parameters &
+						~(dep->interval - 1);
+					dep->flags |= DWC3_EP_MISSED_ISOC;
+				} else {
+					dev_err(dwc->dev, "incomplete IN transfer %s\n",
+							dep->name);
+					status = -ECONNRESET;
+				}
 			}
 		} else {
 			if (count && (event->status & DEPEVT_STATUS_SHORT))
@@ -1604,7 +1713,8 @@ static int dwc3_cleanup_done_reqs(struct dwc3 *dwc, struct dwc3_ep *dep,
 		if (s_pkt)
 			break;
 		if ((event->status & DEPEVT_STATUS_LST) &&
-				(trb->ctrl & DWC3_TRB_CTRL_LST))
+				(trb->ctrl & (DWC3_TRB_CTRL_LST |
+						DWC3_TRB_CTRL_HWO)))
 			break;
 		if ((event->status & DEPEVT_STATUS_IOC) &&
 				(trb->ctrl & DWC3_TRB_CTRL_IOC))
@@ -1657,65 +1767,6 @@ static void dwc3_endpoint_transfer_complete(struct dwc3 *dwc,
 	}
 }
 
-static void dwc3_gadget_start_isoc(struct dwc3 *dwc,
-		struct dwc3_ep *dep, const struct dwc3_event_depevt *event)
-{
-	u32 uf, mask;
-
-	if (list_empty(&dep->request_list)) {
-		dev_vdbg(dwc->dev, "ISOC ep %s run out for requests.\n",
-			dep->name);
-		return;
-	}
-
-	mask = ~(dep->interval - 1);
-	uf = event->parameters & mask;
-	/* 4 micro frames in the future */
-	uf += dep->interval * 4;
-
-	__dwc3_gadget_kick_transfer(dep, uf, 1);
-}
-
-static void dwc3_process_ep_cmd_complete(struct dwc3_ep *dep,
-		const struct dwc3_event_depevt *event)
-{
-	struct dwc3 *dwc = dep->dwc;
-	struct dwc3_event_depevt mod_ev = *event;
-
-	/*
-	 * We were asked to remove one request. It is possible that this
-	 * request and a few others were started together and have the same
-	 * transfer index. Since we stopped the complete endpoint we don't
-	 * know how many requests were already completed (and not yet)
-	 * reported and how could be done (later). We purge them all until
-	 * the end of the list.
-	 */
-	mod_ev.status = DEPEVT_STATUS_LST;
-	dwc3_cleanup_done_reqs(dwc, dep, &mod_ev, -ESHUTDOWN);
-	dep->flags &= ~DWC3_EP_BUSY;
-	/* pending requests are ignored and are queued on XferNotReady */
-}
-
-static void dwc3_ep_cmd_compl(struct dwc3_ep *dep,
-		const struct dwc3_event_depevt *event)
-{
-	u32 param = event->parameters;
-	u32 cmd_type = (param >> 8) & ((1 << 5) - 1);
-
-	switch (cmd_type) {
-	case DWC3_DEPCMD_ENDTRANSFER:
-		dwc3_process_ep_cmd_complete(dep, event);
-		break;
-	case DWC3_DEPCMD_STARTTRANSFER:
-		dep->res_trans_idx = param & 0x7f;
-		break;
-	default:
-		printk(KERN_ERR "%s() unknown /unexpected type: %d\n",
-				__func__, cmd_type);
-		break;
-	};
-}
-
 static void dwc3_endpoint_interrupt(struct dwc3 *dwc,
 		const struct dwc3_event_depevt *event)
 {
@@ -1724,6 +1775,9 @@ static void dwc3_endpoint_interrupt(struct dwc3 *dwc,
 
 	dep = dwc->eps[epnum];
 
+	if (!(dep->flags & DWC3_EP_ENABLED))
+		return;
+
 	dev_vdbg(dwc->dev, "%s: %s\n", dep->name,
 			dwc3_ep_event_string(event->endpoint_event));
 
@@ -1734,7 +1788,7 @@ static void dwc3_endpoint_interrupt(struct dwc3 *dwc,
 
 	switch (event->endpoint_event) {
 	case DWC3_DEPEVT_XFERCOMPLETE:
-		dep->res_trans_idx = 0;
+		dep->resource_index = 0;
 
 		if (usb_endpoint_xfer_isoc(dep->endpoint.desc)) {
 			dev_dbg(dwc->dev, "%s is an Isochronous endpoint\n",
@@ -1797,7 +1851,7 @@ static void dwc3_endpoint_interrupt(struct dwc3 *dwc,
 		dev_dbg(dwc->dev, "%s FIFO Overrun\n", dep->name);
 		break;
 	case DWC3_DEPEVT_EPCMDCMPLT:
-		dwc3_ep_cmd_compl(dep, event);
+		dev_vdbg(dwc->dev, "Endpoint Command Complete\n");
 		break;
 	}
 }
@@ -1820,16 +1874,16 @@ static void dwc3_stop_active_transfer(struct dwc3 *dwc, u32 epnum)
 
 	dep = dwc->eps[epnum];
 
-	WARN_ON(!dep->res_trans_idx);
-	if (dep->res_trans_idx) {
-		cmd = DWC3_DEPCMD_ENDTRANSFER;
-		cmd |= DWC3_DEPCMD_HIPRI_FORCERM | DWC3_DEPCMD_CMDIOC;
-		cmd |= DWC3_DEPCMD_PARAM(dep->res_trans_idx);
-		memset(&params, 0, sizeof(params));
-		ret = dwc3_send_gadget_ep_cmd(dwc, dep->number, cmd, &params);
-		WARN_ON_ONCE(ret);
-		dep->res_trans_idx = 0;
-	}
+	if (!dep->resource_index)
+		return;
+
+	cmd = DWC3_DEPCMD_ENDTRANSFER;
+	cmd |= DWC3_DEPCMD_HIPRI_FORCERM | DWC3_DEPCMD_CMDIOC;
+	cmd |= DWC3_DEPCMD_PARAM(dep->resource_index);
+	memset(&params, 0, sizeof(params));
+	ret = dwc3_send_gadget_ep_cmd(dwc, dep->number, cmd, &params);
+	WARN_ON_ONCE(ret);
+	dep->resource_index = 0;
 }
 
 static void dwc3_stop_active_transfers(struct dwc3 *dwc)
@@ -1872,11 +1926,9 @@ static void dwc3_clear_stall_all_ep(struct dwc3 *dwc)
 
 static void dwc3_gadget_disconnect_interrupt(struct dwc3 *dwc)
 {
+	int			reg;
+
 	dev_vdbg(dwc->dev, "%s\n", __func__);
-#if 0
-	XXX
-	U1/U2 is powersave optimization. Skip it for now. Anyway we need to
-	enable it before we can disable it.
 
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	reg &= ~DWC3_DCTL_INITU1ENA;
@@ -1884,9 +1936,7 @@ static void dwc3_gadget_disconnect_interrupt(struct dwc3 *dwc)
 
 	reg &= ~DWC3_DCTL_INITU2ENA;
 	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
-#endif
 
-	dwc3_stop_active_transfers(dwc);
 	dwc3_disconnect_gadget(dwc);
 	dwc->start_config_issued = false;
 
@@ -1894,30 +1944,30 @@ static void dwc3_gadget_disconnect_interrupt(struct dwc3 *dwc)
 	dwc->setup_packet_pending = false;
 }
 
-static void dwc3_gadget_usb3_phy_power(struct dwc3 *dwc, int on)
+static void dwc3_gadget_usb3_phy_suspend(struct dwc3 *dwc, int suspend)
 {
 	u32			reg;
 
 	reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
 
-	if (on)
-		reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
-	else
+	if (suspend)
 		reg |= DWC3_GUSB3PIPECTL_SUSPHY;
+	else
+		reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
 
 	dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
 }
 
-static void dwc3_gadget_usb2_phy_power(struct dwc3 *dwc, int on)
+static void dwc3_gadget_usb2_phy_suspend(struct dwc3 *dwc, int suspend)
 {
 	u32			reg;
 
 	reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
 
-	if (on)
-		reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
-	else
+	if (suspend)
 		reg |= DWC3_GUSB2PHYCFG_SUSPHY;
+	else
+		reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
 
 	dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 }
@@ -1962,16 +2012,18 @@ static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
 	/* after reset -> Default State */
 	dwc->dev_state = DWC3_DEFAULT_STATE;
 
-	/* Enable PHYs */
-	dwc3_gadget_usb2_phy_power(dwc, true);
-	dwc3_gadget_usb3_phy_power(dwc, true);
+	/* Recent versions support automatic phy suspend and don't need this */
+	if (dwc->revision < DWC3_REVISION_194A) {
+		/* Resume PHYs */
+		dwc3_gadget_usb2_phy_suspend(dwc, false);
+		dwc3_gadget_usb3_phy_suspend(dwc, false);
+	}
 
 	if (dwc->gadget.speed != USB_SPEED_UNKNOWN)
 		dwc3_disconnect_gadget(dwc);
 
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	reg &= ~DWC3_DCTL_TSTCTRL_MASK;
-	reg &= ~(DWC3_DCTL_INITU1ENA | DWC3_DCTL_INITU2ENA);
 	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
 	dwc->test_mode = false;
 
@@ -2010,16 +2062,16 @@ static void dwc3_update_ram_clk_sel(struct dwc3 *dwc, u32 speed)
 	dwc3_writel(dwc->regs, DWC3_GCTL, reg);
 }
 
-static void dwc3_gadget_disable_phy(struct dwc3 *dwc, u8 speed)
+static void dwc3_gadget_phy_suspend(struct dwc3 *dwc, u8 speed)
 {
 	switch (speed) {
 	case USB_SPEED_SUPER:
-		dwc3_gadget_usb2_phy_power(dwc, false);
+		dwc3_gadget_usb2_phy_suspend(dwc, true);
 		break;
 	case USB_SPEED_HIGH:
 	case USB_SPEED_FULL:
 	case USB_SPEED_LOW:
-		dwc3_gadget_usb3_phy_power(dwc, false);
+		dwc3_gadget_usb3_phy_suspend(dwc, true);
 		break;
 	}
 }
@@ -2082,8 +2134,11 @@ static void dwc3_gadget_conndone_interrupt(struct dwc3 *dwc)
 		break;
 	}
 
-	/* Disable unneded PHY */
-	dwc3_gadget_disable_phy(dwc, dwc->gadget.speed);
+	/* Recent versions support automatic phy suspend and don't need this */
+	if (dwc->revision < DWC3_REVISION_194A) {
+		/* Suspend unneeded PHY */
+		dwc3_gadget_phy_suspend(dwc, dwc->gadget.speed);
+	}
 
 	dep = dwc->eps[0];
 	ret = __dwc3_gadget_ep_enable(dep, &dwc3_gadget_ep0_desc, NULL);
@@ -2373,10 +2428,6 @@ int __devinit dwc3_gadget_init(struct dwc3 *dwc)
 	reg |= DWC3_DCFG_LPM_CAP;
 	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
 
-	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
-	reg |= DWC3_DCTL_ACCEPTU1ENA | DWC3_DCTL_ACCEPTU2ENA;
-	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
-
 	/* Enable all but Start and End of Frame IRQs */
 	reg = (DWC3_DEVTEN_VNDRDEVTSTRCVEDEN |
 			DWC3_DEVTEN_EVNTOVERFLOWEN |
@@ -2389,6 +2440,24 @@ int __devinit dwc3_gadget_init(struct dwc3 *dwc)
 			DWC3_DEVTEN_DISCONNEVTEN);
 	dwc3_writel(dwc->regs, DWC3_DEVTEN, reg);
 
+	/* Enable USB2 LPM and automatic phy suspend only on recent versions */
+	if (dwc->revision >= DWC3_REVISION_194A) {
+		reg = dwc3_readl(dwc->regs, DWC3_DCFG);
+		reg |= DWC3_DCFG_LPM_CAP;
+		dwc3_writel(dwc->regs, DWC3_DCFG, reg);
+
+		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+		reg &= ~(DWC3_DCTL_HIRD_THRES_MASK | DWC3_DCTL_L1_HIBER_EN);
+
+		/* TODO: This should be configurable */
+		reg |= DWC3_DCTL_HIRD_THRES(28);
+
+		dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+
+		dwc3_gadget_usb2_phy_suspend(dwc, false);
+		dwc3_gadget_usb3_phy_suspend(dwc, false);
+	}
+
 	ret = device_register(&dwc->gadget.dev);
 	if (ret) {
 		dev_err(dwc->dev, "failed to register gadget device\n");