diff options
Diffstat (limited to 'drivers/usb/host/ohci-pci.c')
| -rw-r--r-- | drivers/usb/host/ohci-pci.c | 47 |
1 files changed, 3 insertions, 44 deletions
diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c index d0360f65ebd9..3bf175d95a23 100644 --- a/drivers/usb/host/ohci-pci.c +++ b/drivers/usb/host/ohci-pci.c @@ -238,42 +238,6 @@ static int __devinit ohci_pci_start (struct usb_hcd *hcd) return ret; } -#if defined(CONFIG_USB_PERSIST) && (defined(CONFIG_USB_EHCI_HCD) || \ - defined(CONFIG_USB_EHCI_HCD_MODULE)) - -/* Following a power loss, we must prepare to regain control of the ports - * we used to own. This means turning on the port power before ehci-hcd - * tries to switch ownership. - * - * This isn't a 100% perfect solution. On most systems the OHCI controllers - * lie at lower PCI addresses than the EHCI controller, so they will be - * discovered (and hence resumed) first. But there is no guarantee things - * will always work this way. If the EHCI controller is resumed first and - * the OHCI ports are unpowered, then the handover will fail. - */ -static void prepare_for_handover(struct usb_hcd *hcd) -{ - struct ohci_hcd *ohci = hcd_to_ohci(hcd); - int port; - - /* Here we "know" root ports should always stay powered */ - ohci_dbg(ohci, "powerup ports\n"); - for (port = 0; port < ohci->num_ports; port++) - ohci_writel(ohci, RH_PS_PPS, - &ohci->regs->roothub.portstatus[port]); - - /* Flush those writes */ - ohci_readl(ohci, &ohci->regs->control); - msleep(20); -} - -#else - -static inline void prepare_for_handover(struct usb_hcd *hcd) -{ } - -#endif /* CONFIG_USB_PERSIST etc. */ - #ifdef CONFIG_PM static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message) @@ -313,10 +277,7 @@ static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message) static int ohci_pci_resume (struct usb_hcd *hcd) { set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); - - /* FIXME: we should try to detect loss of VBUS power here */ - prepare_for_handover(hcd); - + ohci_finish_controller_resume(hcd); return 0; } @@ -345,9 +306,8 @@ static const struct hc_driver ohci_pci_hc_driver = { .shutdown = ohci_shutdown, #ifdef CONFIG_PM - /* these suspend/resume entries are for upstream PCI glue ONLY */ - .suspend = ohci_pci_suspend, - .resume = ohci_pci_resume, + .pci_suspend = ohci_pci_suspend, + .pci_resume = ohci_pci_resume, #endif /* @@ -367,7 +327,6 @@ static const struct hc_driver ohci_pci_hc_driver = { */ .hub_status_data = ohci_hub_status_data, .hub_control = ohci_hub_control, - .hub_irq_enable = ohci_rhsc_enable, #ifdef CONFIG_PM .bus_suspend = ohci_bus_suspend, .bus_resume = ohci_bus_resume, |