diff options
Diffstat (limited to 'drivers/usb/input/powermate.c')
| -rw-r--r-- | drivers/usb/input/powermate.c | 30 |
1 files changed, 15 insertions, 15 deletions
diff --git a/drivers/usb/input/powermate.c b/drivers/usb/input/powermate.c index 7fa2f9b9fb69..3975b309d55f 100644 --- a/drivers/usb/input/powermate.c +++ b/drivers/usb/input/powermate.c @@ -10,7 +10,7 @@ * back to the host when polled by the USB controller. * * Testing with the knob I have has shown that it measures approximately 94 "clicks" - * for one full rotation. Testing with my High Speed Rotation Actuator (ok, it was + * for one full rotation. Testing with my High Speed Rotation Actuator (ok, it was * a variable speed cordless electric drill) has shown that the device can measure * speeds of up to 7 clicks either clockwise or anticlockwise between pollings from * the host. If it counts more than 7 clicks before it is polled, it will wrap back @@ -120,9 +120,9 @@ exit: /* Decide if we need to issue a control message and do so. Must be called with pm->lock taken */ static void powermate_sync_state(struct powermate_device *pm) { - if (pm->requires_update == 0) + if (pm->requires_update == 0) return; /* no updates are required */ - if (pm->config->status == -EINPROGRESS) + if (pm->config->status == -EINPROGRESS) return; /* an update is already in progress; it'll issue this update when it completes */ if (pm->requires_update & UPDATE_PULSE_ASLEEP){ @@ -142,7 +142,7 @@ static void powermate_sync_state(struct powermate_device *pm) 2: multiply the speed the argument only has an effect for operations 0 and 2, and ranges between 1 (least effect) to 255 (maximum effect). - + thus, several states are equivalent and are coalesced into one state. we map this onto a range from 0 to 510, with: @@ -151,7 +151,7 @@ static void powermate_sync_state(struct powermate_device *pm) 256 -- 510 -- use multiple (510 = fastest). Only values of 'arg' quite close to 255 are particularly useful/spectacular. - */ + */ if (pm->pulse_speed < 255){ op = 0; // divide arg = 255 - pm->pulse_speed; @@ -199,14 +199,14 @@ static void powermate_config_complete(struct urb *urb, struct pt_regs *regs) if (urb->status) printk(KERN_ERR "powermate: config urb returned %d\n", urb->status); - + spin_lock_irqsave(&pm->lock, flags); powermate_sync_state(pm); spin_unlock_irqrestore(&pm->lock, flags); } /* Set the LED up as described and begin the sync with the hardware if required */ -static void powermate_pulse_led(struct powermate_device *pm, int static_brightness, int pulse_speed, +static void powermate_pulse_led(struct powermate_device *pm, int static_brightness, int pulse_speed, int pulse_table, int pulse_asleep, int pulse_awake) { unsigned long flags; @@ -229,7 +229,7 @@ static void powermate_pulse_led(struct powermate_device *pm, int static_brightne /* mark state updates which are required */ if (static_brightness != pm->static_brightness){ pm->static_brightness = static_brightness; - pm->requires_update |= UPDATE_STATIC_BRIGHTNESS; + pm->requires_update |= UPDATE_STATIC_BRIGHTNESS; } if (pulse_asleep != pm->pulse_asleep){ pm->pulse_asleep = pulse_asleep; @@ -246,7 +246,7 @@ static void powermate_pulse_led(struct powermate_device *pm, int static_brightne } powermate_sync_state(pm); - + spin_unlock_irqrestore(&pm->lock, flags); } @@ -257,19 +257,19 @@ static int powermate_input_event(struct input_dev *dev, unsigned int type, unsig struct powermate_device *pm = dev->private; if (type == EV_MSC && code == MSC_PULSELED){ - /* + /* bits 0- 7: 8 bits: LED brightness bits 8-16: 9 bits: pulsing speed modifier (0 ... 510); 0-254 = slower, 255 = standard, 256-510 = faster. bits 17-18: 2 bits: pulse table (0, 1, 2 valid) bit 19: 1 bit : pulse whilst asleep? bit 20: 1 bit : pulse constantly? - */ + */ int static_brightness = command & 0xFF; // bits 0-7 int pulse_speed = (command >> 8) & 0x1FF; // bits 8-16 int pulse_table = (command >> 17) & 0x3; // bits 17-18 int pulse_asleep = (command >> 19) & 0x1; // bit 19 int pulse_awake = (command >> 20) & 0x1; // bit 20 - + powermate_pulse_led(pm, static_brightness, pulse_speed, pulse_table, pulse_asleep, pulse_awake); } @@ -378,7 +378,7 @@ static int powermate_probe(struct usb_interface *intf, const struct usb_device_i switch (le16_to_cpu(udev->descriptor.idProduct)) { case POWERMATE_PRODUCT_NEW: pm->input.name = pm_name_powermate; break; case POWERMATE_PRODUCT_OLD: pm->input.name = pm_name_soundknob; break; - default: + default: pm->input.name = pm_name_soundknob; printk(KERN_WARNING "powermate: unknown product id %04x\n", le16_to_cpu(udev->descriptor.idProduct)); @@ -402,11 +402,11 @@ static int powermate_probe(struct usb_interface *intf, const struct usb_device_i usb_make_path(udev, path, 64); snprintf(pm->phys, 64, "%s/input0", path); printk(KERN_INFO "input: %s on %s\n", pm->input.name, pm->input.phys); - + /* force an update of everything */ pm->requires_update = UPDATE_PULSE_ASLEEP | UPDATE_PULSE_AWAKE | UPDATE_PULSE_MODE | UPDATE_STATIC_BRIGHTNESS; powermate_pulse_led(pm, 0x80, 255, 0, 1, 0); // set default pulse parameters - + usb_set_intfdata(intf, pm); return 0; } |