1 files changed, 34 insertions, 14 deletions

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index c45f9c0a1b34..fb0d537435eb 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -904,6 +904,7 @@ static struct usb_device_id id_table_combined [] = {
 	{ USB_DEVICE(FTDI_VID, FTDI_LUMEL_PD12_PID) },
 	/* Crucible Devices */
 	{ USB_DEVICE(FTDI_VID, FTDI_CT_COMET_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_Z3X_PID) },
 	{ }					/* Terminating entry */
 };
 
@@ -1966,8 +1967,16 @@ static int ftdi_process_packet(struct usb_serial_port *port,
 			port->icount.dsr++;
 		if (diff_status & FTDI_RS0_RI)
 			port->icount.rng++;
-		if (diff_status & FTDI_RS0_RLSD)
+		if (diff_status & FTDI_RS0_RLSD) {
+			struct tty_struct *tty;
+
 			port->icount.dcd++;
+			tty = tty_port_tty_get(&port->port);
+			if (tty)
+				usb_serial_handle_dcd_change(port, tty,
+						status & FTDI_RS0_RLSD);
+			tty_kref_put(tty);
+		}
 
 		wake_up_interruptible(&port->port.delta_msr_wait);
 		priv->prev_status = status;
@@ -2114,6 +2123,20 @@ static void ftdi_set_termios(struct tty_struct *tty,
 		termios->c_cflag |= CRTSCTS;
 	}
 
+	/*
+	 * All FTDI UART chips are limited to CS7/8. We won't pretend to
+	 * support CS5/6 and revert the CSIZE setting instead.
+	 */
+	if ((C_CSIZE(tty) != CS8) && (C_CSIZE(tty) != CS7)) {
+		dev_warn(ddev, "requested CSIZE setting not supported\n");
+
+		termios->c_cflag &= ~CSIZE;
+		if (old_termios)
+			termios->c_cflag |= old_termios->c_cflag & CSIZE;
+		else
+			termios->c_cflag |= CS8;
+	}
+
 	cflag = termios->c_cflag;
 
 	if (!old_termios)
@@ -2150,19 +2173,16 @@ no_skip:
 	} else {
 		urb_value |= FTDI_SIO_SET_DATA_PARITY_NONE;
 	}
-	if (cflag & CSIZE) {
-		switch (cflag & CSIZE) {
-		case CS7:
-			urb_value |= 7;
-			dev_dbg(ddev, "Setting CS7\n");
-			break;
-		case CS8:
-			urb_value |= 8;
-			dev_dbg(ddev, "Setting CS8\n");
-			break;
-		default:
-			dev_err(ddev, "CSIZE was set but not CS7-CS8\n");
-		}
+	switch (cflag & CSIZE) {
+	case CS7:
+		urb_value |= 7;
+		dev_dbg(ddev, "Setting CS7\n");
+		break;
+	default:
+	case CS8:
+		urb_value |= 8;
+		dev_dbg(ddev, "Setting CS8\n");
+		break;
 	}
 
 	/* This is needed by the break command since it uses the same command