15 files changed, 633 insertions, 23 deletions

diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 5a8a2c91c2b2..5c60be521561 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -71,6 +71,16 @@ config USB_SERIAL_ANYDATA
 	  To compile this driver as a module, choose M here: the
 	  module will be called anydata.
 
+config USB_SERIAL_ARK3116
+	tristate "USB ARK Micro 3116 USB Serial Driver (EXPERIMENTAL)"
+	depends on USB_SERIAL && EXPERIMENTAL
+	help
+	  Say Y here if you want to use a ARK Micro 3116 USB to Serial
+	  device.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ark3116
+
 config USB_SERIAL_BELKIN
 	tristate "USB Belkin and Peracom Single Port Serial Driver"
 	depends on USB_SERIAL
@@ -158,6 +168,15 @@ config USB_SERIAL_FTDI_SIO
 	  To compile this driver as a module, choose M here: the
 	  module will be called ftdi_sio.
 
+config USB_SERIAL_FUNSOFT
+	tristate "USB Fundamental Software Dongle Driver"
+	depends on USB_SERIAL
+	---help---
+	  Say Y here if you want to use the Fundamental Software dongle.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called funsoft.
+
 config USB_SERIAL_VISOR
 	tristate "USB Handspring Visor / Palm m50x / Sony Clie Driver"
 	depends on USB_SERIAL
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index f7fe4172efed..5a0960fc9d3e 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -13,6 +13,7 @@ usbserial-objs	:= usb-serial.o generic.o bus.o $(usbserial-obj-y)
 
 obj-$(CONFIG_USB_SERIAL_AIRPRIME)		+= airprime.o
 obj-$(CONFIG_USB_SERIAL_ANYDATA)		+= anydata.o
+obj-$(CONFIG_USB_SERIAL_ARK3116)		+= ark3116.o
 obj-$(CONFIG_USB_SERIAL_BELKIN)			+= belkin_sa.o
 obj-$(CONFIG_USB_SERIAL_CP2101)			+= cp2101.o
 obj-$(CONFIG_USB_SERIAL_CYBERJACK)		+= cyberjack.o
@@ -22,6 +23,7 @@ obj-$(CONFIG_USB_SERIAL_EDGEPORT)		+= io_edgeport.o
 obj-$(CONFIG_USB_SERIAL_EDGEPORT_TI)		+= io_ti.o
 obj-$(CONFIG_USB_SERIAL_EMPEG)			+= empeg.o
 obj-$(CONFIG_USB_SERIAL_FTDI_SIO)		+= ftdi_sio.o
+obj-$(CONFIG_USB_SERIAL_FUNSOFT)		+= funsoft.o
 obj-$(CONFIG_USB_SERIAL_GARMIN)			+= garmin_gps.o
 obj-$(CONFIG_USB_SERIAL_HP4X)			+= hp4x.o
 obj-$(CONFIG_USB_SERIAL_IPAQ)			+= ipaq.o
diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c
index dbf1f063098c..694b205f9b73 100644
--- a/drivers/usb/serial/airprime.c
+++ b/drivers/usb/serial/airprime.c
@@ -18,6 +18,7 @@
 static struct usb_device_id id_table [] = {
 	{ USB_DEVICE(0xf3d, 0x0112) },  /* AirPrime CDMA Wireless PC Card */
 	{ USB_DEVICE(0x1410, 0x1110) }, /* Novatel Wireless Merlin CDMA */
+	{ USB_DEVICE(0x1199, 0x0112) }, /* Sierra Wireless Aircard 580 */
 	{ },
 };
 MODULE_DEVICE_TABLE(usb, id_table);
diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c
new file mode 100644
index 000000000000..8dec796222a0
--- /dev/null
+++ b/drivers/usb/serial/ark3116.c
@@ -0,0 +1,465 @@
+/*
+ * ark3116
+ * - implements a driver for the arkmicro ark3116 chipset (vendor=0x6547,
+ *   productid=0x0232) (used in a datacable called KQ-U8A)
+ *
+ * - based on code by krisfx -> thanks !!
+ *   (see http://www.linuxquestions.org/questions/showthread.php?p=2184457#post2184457)
+ *
+ *  - based on logs created by usbsnoopy
+ *
+ *  Author   : Simon Schulz [ark3116_driver<AT>auctionant.de]
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include "usb-serial.h"
+
+
+static int debug;
+
+static struct usb_device_id id_table [] = {
+	{ USB_DEVICE(0x6547, 0x0232) },
+	{ },
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+struct ark3116_private {
+	spinlock_t lock;
+	u8 termios_initialized;
+};
+
+static inline void ARK3116_SND(struct usb_serial *serial, int seq,
+			       __u8 request, __u8 requesttype,
+			       __u16 value, __u16 index)
+{
+	int result;
+	result = usb_control_msg(serial->dev,
+				 usb_sndctrlpipe(serial->dev,0),
+				 request, requesttype, value, index,
+				 NULL,0x00, 1000);
+	dbg("%03d > ok",seq);
+}
+
+static inline void ARK3116_RCV(struct usb_serial *serial, int seq,
+			       __u8 request, __u8 requesttype,
+			       __u16 value, __u16 index, __u8 expected,
+			       char *buf)
+{
+	int result;
+	result = usb_control_msg(serial->dev,
+			      usb_rcvctrlpipe(serial->dev,0),
+			      request, requesttype, value, index,
+			      buf, 0x0000001, 1000);
+	if (result)
+		dbg("%03d < %d bytes [0x%02X]",seq, result, buf[0]);
+	else
+		dbg("%03d < 0 bytes", seq);
+}
+
+
+static inline void ARK3116_RCV_QUIET(struct usb_serial *serial,
+				     __u8 request, __u8 requesttype,
+				     __u16 value, __u16 index, char *buf)
+{
+	usb_control_msg(serial->dev,
+			usb_rcvctrlpipe(serial->dev,0),
+			request, requesttype, value, index,
+			buf, 0x0000001, 1000);
+}
+
+
+static int ark3116_attach(struct usb_serial *serial)
+{
+	char *buf;
+	struct ark3116_private *priv;
+	int i;
+
+	for (i = 0; i < serial->num_ports; ++i) {
+		priv = kmalloc (sizeof (struct ark3116_private), GFP_KERNEL);
+		if (!priv)
+			goto cleanup;
+		memset (priv, 0x00, sizeof (struct ark3116_private));
+		spin_lock_init(&priv->lock);
+
+		usb_set_serial_port_data(serial->port[i], priv);
+	}
+
+	buf = kmalloc(1, GFP_KERNEL);
+	if (!buf) {
+		dbg("error kmalloc -> out of mem ?");
+		goto cleanup;
+	}
+
+	/* 3 */
+	ARK3116_SND(serial, 3,0xFE,0x40,0x0008,0x0002);
+	ARK3116_SND(serial, 4,0xFE,0x40,0x0008,0x0001);
+	ARK3116_SND(serial, 5,0xFE,0x40,0x0000,0x0008);
+	ARK3116_SND(serial, 6,0xFE,0x40,0x0000,0x000B);
+
+	/* <-- seq7 */
+	ARK3116_RCV(serial, 7,0xFE,0xC0,0x0000,0x0003, 0x00, buf);
+	ARK3116_SND(serial, 8,0xFE,0x40,0x0080,0x0003);
+	ARK3116_SND(serial, 9,0xFE,0x40,0x001A,0x0000);
+	ARK3116_SND(serial,10,0xFE,0x40,0x0000,0x0001);
+	ARK3116_SND(serial,11,0xFE,0x40,0x0000,0x0003);
+
+	/* <-- seq12 */
+	ARK3116_RCV(serial,12,0xFE,0xC0,0x0000,0x0004, 0x00, buf);
+	ARK3116_SND(serial,13,0xFE,0x40,0x0000,0x0004);
+
+	/* 14 */
+	ARK3116_RCV(serial,14,0xFE,0xC0,0x0000,0x0004, 0x00, buf);
+	ARK3116_SND(serial,15,0xFE,0x40,0x0000,0x0004);
+
+	/* 16 */
+	ARK3116_RCV(serial,16,0xFE,0xC0,0x0000,0x0004, 0x00, buf);
+	/* --> seq17 */
+	ARK3116_SND(serial,17,0xFE,0x40,0x0001,0x0004);
+
+	/* <-- seq18 */
+	ARK3116_RCV(serial,18,0xFE,0xC0,0x0000,0x0004, 0x01, buf);
+
+	/* --> seq19 */
+	ARK3116_SND(serial,19,0xFE,0x40,0x0003,0x0004);
+
+
+	/* <-- seq20 */
+	/* seems like serial port status info (RTS, CTS,...) */
+	/* returns modem control line status ?! */
+	ARK3116_RCV(serial,20,0xFE,0xC0,0x0000,0x0006, 0xFF, buf);
+
+	/* set 9600 baud & do some init ?! */
+	ARK3116_SND(serial,147,0xFE,0x40,0x0083,0x0003);
+	ARK3116_SND(serial,148,0xFE,0x40,0x0038,0x0000);
+	ARK3116_SND(serial,149,0xFE,0x40,0x0001,0x0001);
+	ARK3116_SND(serial,150,0xFE,0x40,0x0003,0x0003);
+	ARK3116_RCV(serial,151,0xFE,0xC0,0x0000,0x0004,0x03, buf);
+	ARK3116_SND(serial,152,0xFE,0x40,0x0000,0x0003);
+	ARK3116_RCV(serial,153,0xFE,0xC0,0x0000,0x0003,0x00, buf);
+	ARK3116_SND(serial,154,0xFE,0x40,0x0003,0x0003);
+
+	kfree(buf);
+	return(0);
+
+cleanup:
+	for (--i; i>=0; --i)
+		usb_set_serial_port_data(serial->port[i], NULL);
+	return -ENOMEM;
+}
+
+static void ark3116_set_termios(struct usb_serial_port *port,
+				struct termios *old_termios)
+{
+	struct usb_serial *serial = port->serial;
+	struct ark3116_private *priv = usb_get_serial_port_data(port);
+	unsigned int cflag = port->tty->termios->c_cflag;
+	unsigned long flags;
+	int baud;
+	int ark3116_baud;
+	char *buf;
+	char config;
+
+	config = 0;
+
+	dbg("%s - port %d", __FUNCTION__, port->number);
+
+	if ((!port->tty) || (!port->tty->termios)) {
+		dbg("%s - no tty structures", __FUNCTION__);
+		return;
+	}
+
+	spin_lock_irqsave(&priv->lock, flags);
+	if (!priv->termios_initialized) {
+		*(port->tty->termios) = tty_std_termios;
+		port->tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+		priv->termios_initialized = 1;
+	}
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	cflag = port->tty->termios->c_cflag;
+
+	/* check that they really want us to change something: */
+	if (old_termios) {
+		if ((cflag == old_termios->c_cflag) &&
+		    (RELEVANT_IFLAG(port->tty->termios->c_iflag) ==
+		     RELEVANT_IFLAG(old_termios->c_iflag))) {
+			dbg("%s - nothing to change...", __FUNCTION__);
+			return;
+		}
+	}
+
+	buf = kmalloc(1, GFP_KERNEL);
+	if (!buf) {
+		dbg("error kmalloc");
+		return;
+	}
+
+	/* set data bit count (8/7/6/5) */
+	if (cflag & CSIZE){
+		switch (cflag & CSIZE){
+		case CS5:
+			config |= 0x00;
+			dbg("setting CS5");
+			break;
+		case CS6:
+			config |= 0x01;
+			dbg("setting CS6");
+			break;
+		case CS7:
+			config |= 0x02;
+			dbg("setting CS7");
+			break;
+		default:
+			err ("CSIZE was set but not CS5-CS8, using CS8!");
+		case CS8:
+			config |= 0x03;
+			dbg("setting CS8");
+			break;
+		}
+	}
+
+	/* set parity (NONE,EVEN,ODD) */
+	if (cflag & PARENB){
+		if (cflag & PARODD) {
+			config |= 0x08;
+			dbg("setting parity to ODD");
+		} else {
+			config |= 0x18;
+			dbg("setting parity to EVEN");
+		}
+	} else {
+		dbg("setting parity to NONE");
+	}
+
+	/* SET STOPBIT (1/2) */
+	if (cflag & CSTOPB) {
+		config |= 0x04;
+		dbg ("setting 2 stop bits");
+	} else {
+		dbg ("setting 1 stop bit");
+	}
+
+
+	/* set baudrate: */
+	baud = 0;
+	switch (cflag & CBAUD){
+		case B0:
+			err("can't set 0baud, using 9600 instead");
+			break;
+		case B75:	baud = 75;	break;
+		case B150:	baud = 150;	break;
+		case B300:	baud = 300;	break;
+		case B600:	baud = 600;	break;
+		case B1200:	baud = 1200;	break;
+		case B1800:	baud = 1800;	break;
+		case B2400:	baud = 2400;	break;
+		case B4800:	baud = 4800;	break;
+		case B9600:	baud = 9600;	break;
+		case B19200:	baud = 19200;	break;
+		case B38400:	baud = 38400;	break;
+		case B57600:	baud = 57600;	break;
+		case B115200:	baud = 115200;	break;
+		case B230400:	baud = 230400;	break;
+		case B460800:	baud = 460800;	break;
+		default:
+			dbg("does not support the baudrate requested (fix it)");
+			break;
+	}
+
+	/* set 9600 as default (if given baudrate is invalid for example) */
+	if (baud == 0)
+		baud = 9600;
+
+	/*
+	 * found by try'n'error, be careful, maybe there are other options
+	 * for multiplicator etc!
+	 */
+	if (baud == 460800)
+		/* strange, for 460800 the formula is wrong
+		 * (dont use round(), then 9600baud is wrong) */
+		ark3116_baud = 7;
+	else
+		ark3116_baud = 3000000 / baud;
+
+	/* ? */
+	ARK3116_RCV(serial,0,0xFE,0xC0,0x0000,0x0003, 0x03, buf);
+	/* offset = buf[0]; */
+	/* offset = 0x03; */
+	/* dbg("using 0x%04X as target for 0x0003:",0x0080+offset); */
+
+
+	/* set baudrate */
+	dbg("setting baudrate to %d (->reg=%d)",baud,ark3116_baud);
+	ARK3116_SND(serial,147,0xFE,0x40,0x0083,0x0003);
+	ARK3116_SND(serial,148,0xFE,0x40,(ark3116_baud & 0x00FF)   ,0x0000);
+	ARK3116_SND(serial,149,0xFE,0x40,(ark3116_baud & 0xFF00)>>8,0x0001);
+	ARK3116_SND(serial,150,0xFE,0x40,0x0003,0x0003);
+
+	/* ? */
+	ARK3116_RCV(serial,151,0xFE,0xC0,0x0000,0x0004,0x03, buf);
+	ARK3116_SND(serial,152,0xFE,0x40,0x0000,0x0003);
+
+	/* set data bit count, stop bit count & parity: */
+	dbg("updating bit count, stop bit or parity (cfg=0x%02X)", config);
+	ARK3116_RCV(serial,153,0xFE,0xC0,0x0000,0x0003,0x00, buf);
+	ARK3116_SND(serial,154,0xFE,0x40,config,0x0003);
+
+	if (cflag & CRTSCTS)
+		dbg("CRTSCTS not supported by chipset ?!");
+
+	/* TEST ARK3116_SND(154,0xFE,0x40,0xFFFF, 0x0006); */
+
+	kfree(buf);
+	return;
+}
+
+static int ark3116_open(struct usb_serial_port *port, struct file *filp)
+{
+	struct termios tmp_termios;
+	struct usb_serial *serial = port->serial;
+	char *buf;
+	int result = 0;
+
+	dbg("%s -  port %d", __FUNCTION__, port->number);
+
+	buf = kmalloc(1, GFP_KERNEL);
+	if (!buf) {
+		dbg("error kmalloc -> out of mem ?");
+		return -ENOMEM;
+	}
+
+	result = usb_serial_generic_open(port, filp);
+	if (result)
+		return result;
+
+	/* open */
+	ARK3116_RCV(serial,111,0xFE,0xC0,0x0000,0x0003, 0x02, buf);
+
+	ARK3116_SND(serial,112,0xFE,0x40,0x0082,0x0003);
+	ARK3116_SND(serial,113,0xFE,0x40,0x001A,0x0000);
+	ARK3116_SND(serial,114,0xFE,0x40,0x0000,0x0001);
+	ARK3116_SND(serial,115,0xFE,0x40,0x0002,0x0003);
+
+	ARK3116_RCV(serial,116,0xFE,0xC0,0x0000,0x0004, 0x03, buf);
+	ARK3116_SND(serial,117,0xFE,0x40,0x0002,0x0004);
+
+	ARK3116_RCV(serial,118,0xFE,0xC0,0x0000,0x0004, 0x02, buf);
+	ARK3116_SND(serial,119,0xFE,0x40,0x0000,0x0004);
+
+	ARK3116_RCV(serial,120,0xFE,0xC0,0x0000,0x0004, 0x00, buf);
+
+	ARK3116_SND(serial,121,0xFE,0x40,0x0001,0x0004);
+
+	ARK3116_RCV(serial,122,0xFE,0xC0,0x0000,0x0004, 0x01, buf);
+
+	ARK3116_SND(serial,123,0xFE,0x40,0x0003,0x0004);
+
+	/* returns different values (control lines ?!) */
+	ARK3116_RCV(serial,124,0xFE,0xC0,0x0000,0x0006, 0xFF, buf);
+
+	/* initialise termios: */
+	if (port->tty)
+		ark3116_set_termios(port, &tmp_termios);
+
+	kfree(buf);
+
+	return result;
+
+}
+
+static int ark3116_ioctl(struct usb_serial_port *port, struct file *file,
+			 unsigned int cmd, unsigned long arg)
+{
+	dbg("ioctl not supported yet...");
+	return -ENOIOCTLCMD;
+}
+
+static int ark3116_tiocmget(struct usb_serial_port *port, struct file *file)
+{
+	struct usb_serial *serial = port->serial;
+	char *buf;
+	char temp;
+
+	/* seems like serial port status info (RTS, CTS,...) is stored
+	 * in reg(?) 0x0006
+	 * pcb connection point 11 = GND -> sets bit4 of response
+	 * pcb connection point  7 = GND -> sets bit6 of response
+	 */
+
+	buf = kmalloc(1, GFP_KERNEL);
+	if (!buf) {
+		dbg("error kmalloc");
+		return -ENOMEM;
+	}
+
+	/* read register: */
+	ARK3116_RCV_QUIET(serial,0xFE,0xC0,0x0000,0x0006,buf);
+	temp = buf[0];
+	kfree(buf);
+
+	/* i do not really know if bit4=CTS and bit6=DSR... was just a
+	 * quick guess !!
+	 */
+	return  (temp & (1<<4) ? TIOCM_CTS : 0) |
+	        (temp & (1<<6) ? TIOCM_DSR : 0);
+}
+
+static struct usb_driver ark3116_driver = {
+	.name =		"ark3116",
+	.probe =	usb_serial_probe,
+	.disconnect =	usb_serial_disconnect,
+	.id_table =	id_table,
+};
+
+static struct usb_serial_driver ark3116_device = {
+	.driver = {
+		.owner =	THIS_MODULE,
+		.name =		"ark3116",
+	},
+	.id_table =		id_table,
+	.num_interrupt_in =	1,
+	.num_bulk_in =		1,
+	.num_bulk_out =		1,
+	.num_ports =		1,
+	.attach =		ark3116_attach,
+	.set_termios =		ark3116_set_termios,
+	.ioctl =		ark3116_ioctl,
+	.tiocmget =		ark3116_tiocmget,
+	.open =			ark3116_open,
+};
+
+static int __init ark3116_init(void)
+{
+	int retval;
+
+	retval = usb_serial_register(&ark3116_device);
+	if (retval)
+		return retval;
+	retval = usb_register(&ark3116_driver);
+	if (retval)
+		usb_serial_deregister(&ark3116_device);
+	return retval;
+}
+
+static void __exit ark3116_exit(void)
+{
+	usb_deregister(&ark3116_driver);
+	usb_serial_deregister(&ark3116_device);
+}
+
+module_init(ark3116_init);
+module_exit(ark3116_exit);
+MODULE_LICENSE("GPL");
+
+module_param(debug, bool, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(debug, "Debug enabled or not");
+
diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c
index 167f8ec56131..8023bb7279b1 100644
--- a/drivers/usb/serial/console.c
+++ b/drivers/usb/serial/console.c
@@ -54,7 +54,7 @@ static struct console usbcons;
  * serial.c code, except that the specifier is "ttyUSB" instead
  * of "ttyS".
  */
-static int __init usb_console_setup(struct console *co, char *options)
+static int usb_console_setup(struct console *co, char *options)
 {
 	struct usbcons_info *info = &usbcons_info;
 	int baud = 9600;
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index f3af81b4dd29..986d7622273d 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -307,7 +307,9 @@ static struct ftdi_sio_quirk ftdi_HE_TIRA1_quirk = {
 
 
 static struct usb_device_id id_table_combined [] = {
+	{ USB_DEVICE(FTDI_VID, FTDI_ACTZWAVE_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_IRTRANS_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_IPLUS_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_SIO_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_8U232AM_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) },
@@ -489,10 +491,15 @@ static struct usb_device_id id_table_combined [] = {
 	{ USB_DEVICE(KOBIL_VID, KOBIL_CONV_KAAN_PID) },
 	{ USB_DEVICE(POSIFLEX_VID, POSIFLEX_PP7000_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_TTUSB_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_ECLO_COM_1WIRE_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_WESTREX_MODEL_777_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_WESTREX_MODEL_8900F_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_PCDJ_DAC2_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_RRCIRKITS_LOCOBUFFER_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_ASK_RDR400_PID) },
 	{ USB_DEVICE(ICOM_ID1_VID, ICOM_ID1_PID) },
+	{ USB_DEVICE(PAPOUCH_VID, PAPOUCH_TMU_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_ACG_HFDUAL_PID) },
 	{ },					/* Optional parameter entry */
 	{ }					/* Terminating entry */
 };
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index 8da773c2744d..d69a917e768f 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -32,6 +32,10 @@
 #define FTDI_NF_RIC_PID	0x0001	/* Product Id */
 
 
+/* ACT Solutions HomePro ZWave interface (http://www.act-solutions.com/HomePro.htm) */
+#define FTDI_ACTZWAVE_PID	0xF2D0
+
+
 /* www.irtrans.de device */
 #define FTDI_IRTRANS_PID 0xFC60 /* Product Id */
 
@@ -39,6 +43,9 @@
 /* www.thoughttechnology.com/ TT-USB provide with procomp use ftdi_sio */
 #define FTDI_TTUSB_PID 0xFF20 /* Product Id */
 
+/* iPlus device */
+#define FTDI_IPLUS_PID 0xD070 /* Product Id */
+
 /* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */
 /* they use the ftdi chipset for the USB interface and the vendor id is the same */
 #define FTDI_XF_632_PID 0xFC08	/* 632: 16x2 Character Display */
@@ -153,6 +160,11 @@
 #define ICOM_ID1_PID            0x0004
 
 /*
+ * ASK.fr devices
+ */
+#define FTDI_ASK_RDR400_PID	0xC991	/* ASK RDR 400 series card reader */
+
+/*
  * DSS-20 Sync Station for Sony Ericsson P800
  */
  
@@ -399,6 +411,31 @@
 #define FTDI_WESTREX_MODEL_777_PID	0xDC00	/* Model 777 */
 #define FTDI_WESTREX_MODEL_8900F_PID	0xDC01	/* Model 8900F */
 
+/*
+ * RR-CirKits LocoBuffer USB (http://www.rr-cirkits.com)
+ */
+#define FTDI_RRCIRKITS_LOCOBUFFER_PID	0xc7d0	/* LocoBuffer USB */
+
+/*
+ * Eclo (http://www.eclo.pt/) product IDs.
+ * PID 0xEA90 submitted by Martin Grill.
+ */
+#define FTDI_ECLO_COM_1WIRE_PID	0xEA90	/* COM to 1-Wire USB adaptor */
+
+/*
+ * Papouch products (http://www.papouch.com/)
+ * Submitted by Folkert van Heusden
+ */
+
+#define PAPOUCH_VID			0x5050	/* Vendor ID */
+#define PAPOUCH_TMU_PID			0x0400	/* TMU USB Thermometer */
+
+/*
+ * ACG Identification Technologies GmbH products (http://www.acg.de/).
+ * Submitted by anton -at- goto10 -dot- org.
+ */
+#define FTDI_ACG_HFDUAL_PID		0xDD20	/* HF Dual ISO Reader (RFID) */
+
 /* Commands */
 #define FTDI_SIO_RESET 		0 /* Reset the port */
 #define FTDI_SIO_MODEM_CTRL 	1 /* Set the modem control register */
diff --git a/drivers/usb/serial/funsoft.c b/drivers/usb/serial/funsoft.c
new file mode 100644
index 000000000000..803721b97e2e
--- /dev/null
+++ b/drivers/usb/serial/funsoft.c
@@ -0,0 +1,65 @@
+/*
+ * Funsoft Serial USB driver
+ *
+ * Copyright (C) 2006 Greg Kroah-Hartman <gregkh@suse.de>
+ *
+ *	This program is free software; you can redistribute it and/or
+ *	modify it under the terms of the GNU General Public License version
+ *	2 as published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include "usb-serial.h"
+
+static struct usb_device_id id_table [] = {
+	{ USB_DEVICE(0x1404, 0xcddc) },
+	{ },
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+static struct usb_driver funsoft_driver = {
+	.name =		"funsoft",
+	.probe =	usb_serial_probe,
+	.disconnect =	usb_serial_disconnect,
+	.id_table =	id_table,
+	.no_dynamic_id = 	1,
+};
+
+static struct usb_serial_driver funsoft_device = {
+	.driver = {
+		.owner =	THIS_MODULE,
+		.name =		"funsoft",
+	},
+	.id_table =		id_table,
+	.num_interrupt_in =	NUM_DONT_CARE,
+	.num_bulk_in =		NUM_DONT_CARE,
+	.num_bulk_out =		NUM_DONT_CARE,
+	.num_ports =		1,
+};
+
+static int __init funsoft_init(void)
+{
+	int retval;
+
+	retval = usb_serial_register(&funsoft_device);
+	if (retval)
+		return retval;
+	retval = usb_register(&funsoft_driver);
+	if (retval)
+		usb_serial_deregister(&funsoft_device);
+	return retval;
+}
+
+static void __exit funsoft_exit(void)
+{
+	usb_deregister(&funsoft_driver);
+	usb_serial_deregister(&funsoft_device);
+}
+
+module_init(funsoft_init);
+module_exit(funsoft_exit);
+MODULE_LICENSE("GPL");
diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c
index 476cda107f4f..c62cc2876519 100644
--- a/drivers/usb/serial/generic.c
+++ b/drivers/usb/serial/generic.c
@@ -138,6 +138,7 @@ int usb_serial_generic_open (struct usb_serial_port *port, struct file *filp)
 
 	return result;
 }
+EXPORT_SYMBOL_GPL(usb_serial_generic_open);
 
 static void generic_cleanup (struct usb_serial_port *port)
 {
diff --git a/drivers/usb/serial/omninet.c b/drivers/usb/serial/omninet.c
index 4d40704dea2c..238033a87092 100644
--- a/drivers/usb/serial/omninet.c
+++ b/drivers/usb/serial/omninet.c
@@ -257,14 +257,14 @@ static int omninet_write (struct usb_serial_port *port, const unsigned char *buf
 		return (0);
 	}
 
-	spin_lock(&port->lock);
-	if (port->write_urb_busy) {
-		spin_unlock(&port->lock);
+	spin_lock(&wport->lock);
+	if (wport->write_urb_busy) {
+		spin_unlock(&wport->lock);
 		dbg("%s - already writing", __FUNCTION__);
 		return 0;
 	}
-	port->write_urb_busy = 1;
-	spin_unlock(&port->lock);
+	wport->write_urb_busy = 1;
+	spin_unlock(&wport->lock);
 
 	count = (count > OMNINET_BULKOUTSIZE) ? OMNINET_BULKOUTSIZE : count;
 
@@ -283,7 +283,7 @@ static int omninet_write (struct usb_serial_port *port, const unsigned char *buf
 	wport->write_urb->dev = serial->dev;
 	result = usb_submit_urb(wport->write_urb, GFP_ATOMIC);
 	if (result) {
-		port->write_urb_busy = 0;
+		wport->write_urb_busy = 0;
 		err("%s - failed submitting write urb, error %d", __FUNCTION__, result);
 	} else
 		result = count;
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index b3014fda645c..c96714bb1cb8 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -61,6 +61,7 @@ static struct usb_device_id id_table [] = {
 	{ USB_DEVICE(ELCOM_VENDOR_ID, ELCOM_PRODUCT_ID) },
 	{ USB_DEVICE(ELCOM_VENDOR_ID, ELCOM_PRODUCT_ID_UCSGT) },
 	{ USB_DEVICE(ITEGNO_VENDOR_ID, ITEGNO_PRODUCT_ID) },
+	{ USB_DEVICE(ITEGNO_VENDOR_ID, ITEGNO_PRODUCT_ID_2080) },
 	{ USB_DEVICE(MA620_VENDOR_ID, MA620_PRODUCT_ID) },
 	{ USB_DEVICE(RATOC_VENDOR_ID, RATOC_PRODUCT_ID) },
 	{ USB_DEVICE(TRIPP_VENDOR_ID, TRIPP_PRODUCT_ID) },
@@ -78,6 +79,7 @@ static struct usb_device_id id_table [] = {
 	{ USB_DEVICE(SAGEM_VENDOR_ID, SAGEM_PRODUCT_ID) },
 	{ USB_DEVICE(LEADTEK_VENDOR_ID, LEADTEK_9531_PRODUCT_ID) },
 	{ USB_DEVICE(SPEEDDRAGON_VENDOR_ID, SPEEDDRAGON_PRODUCT_ID) },
+	{ USB_DEVICE(OTI_VENDOR_ID, OTI_PRODUCT_ID) },
 	{ }					/* Terminating entry */
 };
 
diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h
index 77901d143979..7f29e81d3e35 100644
--- a/drivers/usb/serial/pl2303.h
+++ b/drivers/usb/serial/pl2303.h
@@ -26,6 +26,7 @@
 
 #define ITEGNO_VENDOR_ID	0x0eba
 #define ITEGNO_PRODUCT_ID	0x1080
+#define ITEGNO_PRODUCT_ID_2080	0x2080
 
 #define MA620_VENDOR_ID		0x0df7
 #define MA620_PRODUCT_ID	0x0620
@@ -79,3 +80,7 @@
 /* USB GSM cable from Speed Dragon Multimedia, Ltd */
 #define SPEEDDRAGON_VENDOR_ID	0x0e55
 #define SPEEDDRAGON_PRODUCT_ID	0x110b
+
+/* Ours Technology Inc DKU-5 clone, chipset: Prolific Technology Inc */
+#define OTI_VENDOR_ID	0x0ea0
+#define OTI_PRODUCT_ID	0x6858
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 097f4e8488fe..9c36f0ece20f 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -27,10 +27,10 @@
 #include <linux/module.h>
 #include <linux/moduleparam.h>
 #include <linux/spinlock.h>
+#include <linux/mutex.h>
 #include <linux/list.h>
 #include <linux/smp_lock.h>
 #include <asm/uaccess.h>
-#include <asm/semaphore.h>
 #include <linux/usb.h>
 #include "usb-serial.h"
 #include "pl2303.h"
@@ -189,11 +189,15 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
 
 	portNumber = tty->index - serial->minor;
 	port = serial->port[portNumber];
-	if (!port)
-		return -ENODEV;
+	if (!port) {
+		retval = -ENODEV;
+		goto bailout_kref_put;
+	}
 
-	if (down_interruptible(&port->sem))
-		return -ERESTARTSYS;
+	if (mutex_lock_interruptible(&port->mutex)) {
+		retval = -ERESTARTSYS;
+		goto bailout_kref_put;
+	}
 	 
 	++port->open_count;
 
@@ -209,7 +213,7 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
 		 * safe because we are called with BKL held */
 		if (!try_module_get(serial->type->driver.owner)) {
 			retval = -ENODEV;
-			goto bailout_kref_put;
+			goto bailout_mutex_unlock;
 		}
 
 		/* only call the device specific open if this 
@@ -219,15 +223,16 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
 			goto bailout_module_put;
 	}
 
-	up(&port->sem);
+	mutex_unlock(&port->mutex);
 	return 0;
 
 bailout_module_put:
 	module_put(serial->type->driver.owner);
+bailout_mutex_unlock:
+	port->open_count = 0;
+	mutex_unlock(&port->mutex);
 bailout_kref_put:
 	kref_put(&serial->kref, destroy_serial);
-	port->open_count = 0;
-	up(&port->sem);
 	return retval;
 }
 
@@ -240,10 +245,10 @@ static void serial_close(struct tty_struct *tty, struct file * filp)
 
 	dbg("%s - port %d", __FUNCTION__, port->number);
 
-	down(&port->sem);
+	mutex_lock(&port->mutex);
 
 	if (port->open_count == 0) {
-		up(&port->sem);
+		mutex_unlock(&port->mutex);
 		return;
 	}
 
@@ -262,7 +267,7 @@ static void serial_close(struct tty_struct *tty, struct file * filp)
 		module_put(port->serial->type->driver.owner);
 	}
 
-	up(&port->sem);
+	mutex_unlock(&port->mutex);
 	kref_put(&port->serial->kref, destroy_serial);
 }
 
@@ -783,7 +788,7 @@ int usb_serial_probe(struct usb_interface *interface,
 		port->number = i + serial->minor;
 		port->serial = serial;
 		spin_lock_init(&port->lock);
-		sema_init(&port->sem, 1);
+		mutex_init(&port->mutex);
 		INIT_WORK(&port->work, usb_serial_port_softint, port);
 		serial->port[i] = port;
 	}
diff --git a/drivers/usb/serial/usb-serial.h b/drivers/usb/serial/usb-serial.h
index d7d27c3385b3..dc89d8710460 100644
--- a/drivers/usb/serial/usb-serial.h
+++ b/drivers/usb/serial/usb-serial.h
@@ -16,7 +16,7 @@
 
 #include <linux/config.h>
 #include <linux/kref.h>
-#include <asm/semaphore.h>
+#include <linux/mutex.h>
 
 #define SERIAL_TTY_MAJOR	188	/* Nice legal number now */
 #define SERIAL_TTY_MINORS	255	/* loads of devices :) */
@@ -31,7 +31,7 @@
  * @serial: pointer back to the struct usb_serial owner of this port.
  * @tty: pointer to the corresponding tty for this port.
  * @lock: spinlock to grab when updating portions of this structure.
- * @sem: semaphore used to synchronize serial_open() and serial_close()
+ * @mutex: mutex used to synchronize serial_open() and serial_close()
  *	access for this port.
  * @number: the number of the port (the minor number).
  * @interrupt_in_buffer: pointer to the interrupt in buffer for this port.
@@ -63,7 +63,7 @@ struct usb_serial_port {
 	struct usb_serial *	serial;
 	struct tty_struct *	tty;
 	spinlock_t		lock;
-	struct semaphore        sem;
+	struct mutex            mutex;
 	unsigned char		number;
 
 	unsigned char *		interrupt_in_buffer;
diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c
index 557411c6e7c7..f806553cd9a4 100644
--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -508,6 +508,7 @@ no_firmware:
 	err("%s: Unable to retrieve firmware version, try replugging\n", serial->type->description);
 	err("%s: If the firmware is not running (status led not blinking)\n", serial->type->description);
 	err("%s: please contact support@connecttech.com\n", serial->type->description);
+	kfree(result);
 	return -ENODEV;
 
 no_command_private: