diff options
Diffstat (limited to 'drivers/usb/storage/scsiglue.c')
| -rw-r--r-- | drivers/usb/storage/scsiglue.c | 37 |
1 files changed, 19 insertions, 18 deletions
diff --git a/drivers/usb/storage/scsiglue.c b/drivers/usb/storage/scsiglue.c index e1072d52d641..e227f64d5641 100644 --- a/drivers/usb/storage/scsiglue.c +++ b/drivers/usb/storage/scsiglue.c @@ -110,23 +110,6 @@ static int slave_configure(struct scsi_device *sdev) * the end, scatter-gather buffers follow page boundaries. */ blk_queue_dma_alignment(sdev->request_queue, (512 - 1)); - /* Set the SCSI level to at least 2. We'll leave it at 3 if that's - * what is originally reported. We need this to avoid confusing - * the SCSI layer with devices that report 0 or 1, but need 10-byte - * commands (ala ATAPI devices behind certain bridges, or devices - * which simply have broken INQUIRY data). - * - * NOTE: This means /dev/sg programs (ala cdrecord) will get the - * actual information. This seems to be the preference for - * programs like that. - * - * NOTE: This also means that /proc/scsi/scsi and sysfs may report - * the actual value or the modified one, depending on where the - * data comes from. - */ - if (sdev->scsi_level < SCSI_2) - sdev->scsi_level = sdev->sdev_target->scsi_level = SCSI_2; - /* Many devices have trouble transfering more than 32KB at a time, * while others have trouble with more than 64K. At this time we * are limiting both to 32K (64 sectores). @@ -170,13 +153,21 @@ static int slave_configure(struct scsi_device *sdev) if (us->flags & US_FL_FIX_CAPACITY) sdev->fix_capacity = 1; + /* A few disks have two indistinguishable version, one of + * which reports the correct capacity and the other does not. + * The sd driver has to guess which is the case. */ + if (us->flags & US_FL_CAPACITY_HEURISTICS) + sdev->guess_capacity = 1; + /* Some devices report a SCSI revision level above 2 but are * unable to handle the REPORT LUNS command (for which * support is mandatory at level 3). Since we already have * a Get-Max-LUN request, we won't lose much by setting the * revision level down to 2. The only devices that would be * affected are those with sparse LUNs. */ - sdev->scsi_level = sdev->sdev_target->scsi_level = SCSI_2; + if (sdev->scsi_level > SCSI_2) + sdev->sdev_target->scsi_level = + sdev->scsi_level = SCSI_2; /* USB-IDE bridges tend to report SK = 0x04 (Non-recoverable * Hardware Error) when any low-level error occurs, @@ -194,6 +185,16 @@ static int slave_configure(struct scsi_device *sdev) sdev->use_10_for_ms = 1; } + /* The CB and CBI transports have no way to pass LUN values + * other than the bits in the second byte of a CDB. But those + * bits don't get set to the LUN value if the device reports + * scsi_level == 0 (UNKNOWN). Hence such devices must necessarily + * be single-LUN. + */ + if ((us->protocol == US_PR_CB || us->protocol == US_PR_CBI) && + sdev->scsi_level == SCSI_UNKNOWN) + us->max_lun = 0; + /* Some devices choke when they receive a PREVENT-ALLOW MEDIUM * REMOVAL command, so suppress those commands. */ if (us->flags & US_FL_NOT_LOCKABLE) |