summaryrefslogtreecommitdiffstats
path: root/drivers/usb
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/usb')
-rw-r--r--drivers/usb/atm/ueagle-atm.c22
-rw-r--r--drivers/usb/core/Kconfig12
-rw-r--r--drivers/usb/gadget/composite.c18
-rw-r--r--drivers/usb/host/xhci-mem.c25
-rw-r--r--drivers/usb/misc/uss720.c4
-rw-r--r--drivers/usb/serial/ftdi_sio.c1
-rw-r--r--drivers/usb/serial/ftdi_sio_ids.h5
-rw-r--r--drivers/usb/storage/unusual_devs.h7
8 files changed, 69 insertions, 25 deletions
diff --git a/drivers/usb/atm/ueagle-atm.c b/drivers/usb/atm/ueagle-atm.c
index 44447f54942f..99ac70e32556 100644
--- a/drivers/usb/atm/ueagle-atm.c
+++ b/drivers/usb/atm/ueagle-atm.c
@@ -2206,8 +2206,11 @@ static int uea_boot(struct uea_softc *sc)
goto err1;
}
- sc->kthread = kthread_run(uea_kthread, sc, "ueagle-atm");
- if (sc->kthread == ERR_PTR(-ENOMEM)) {
+ /* Create worker thread, but don't start it here. Start it after
+ * all usbatm generic initialization is done.
+ */
+ sc->kthread = kthread_create(uea_kthread, sc, "ueagle-atm");
+ if (IS_ERR(sc->kthread)) {
uea_err(INS_TO_USBDEV(sc), "failed to create thread\n");
goto err2;
}
@@ -2624,6 +2627,7 @@ static struct usbatm_driver uea_usbatm_driver = {
static int uea_probe(struct usb_interface *intf, const struct usb_device_id *id)
{
struct usb_device *usb = interface_to_usbdev(intf);
+ int ret;
uea_enters(usb);
uea_info(usb, "ADSL device founded vid (%#X) pid (%#X) Rev (%#X): %s\n",
@@ -2637,7 +2641,19 @@ static int uea_probe(struct usb_interface *intf, const struct usb_device_id *id)
if (UEA_IS_PREFIRM(id))
return uea_load_firmware(usb, UEA_CHIP_VERSION(id));
- return usbatm_usb_probe(intf, id, &uea_usbatm_driver);
+ ret = usbatm_usb_probe(intf, id, &uea_usbatm_driver);
+ if (ret == 0) {
+ struct usbatm_data *usbatm = usb_get_intfdata(intf);
+ struct uea_softc *sc = usbatm->driver_data;
+
+ /* Ensure carrier is initialized to off as early as possible */
+ UPDATE_ATM_SIGNAL(ATM_PHY_SIG_LOST);
+
+ /* Only start the worker thread when all init is done */
+ wake_up_process(sc->kthread);
+ }
+
+ return ret;
}
static void uea_disconnect(struct usb_interface *intf)
diff --git a/drivers/usb/core/Kconfig b/drivers/usb/core/Kconfig
index 9eed5b52d9de..bcc24779ba0e 100644
--- a/drivers/usb/core/Kconfig
+++ b/drivers/usb/core/Kconfig
@@ -107,11 +107,19 @@ config USB_SUSPEND
If you are unsure about this, say N here.
config USB_OTG
- bool
+ bool "OTG support"
depends on USB && EXPERIMENTAL
depends on USB_SUSPEND
default n
-
+ help
+ The most notable feature of USB OTG is support for a
+ "Dual-Role" device, which can act as either a device
+ or a host. The initial role is decided by the type of
+ plug inserted and can be changed later when two dual
+ role devices talk to each other.
+
+ Select this only if your board has Mini-AB/Micro-AB
+ connector.
config USB_OTG_WHITELIST
bool "Rely on OTG Targeted Peripherals List"
diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c
index 7b5cc16e4a0b..8572dad5ecbb 100644
--- a/drivers/usb/gadget/composite.c
+++ b/drivers/usb/gadget/composite.c
@@ -1047,9 +1047,9 @@ composite_unbind(struct usb_gadget *gadget)
kfree(cdev->req->buf);
usb_ep_free_request(gadget->ep0, cdev->req);
}
+ device_remove_file(&gadget->dev, &dev_attr_suspended);
kfree(cdev);
set_gadget_data(gadget, NULL);
- device_remove_file(&gadget->dev, &dev_attr_suspended);
composite = NULL;
}
@@ -1107,14 +1107,6 @@ static int composite_bind(struct usb_gadget *gadget)
*/
usb_ep_autoconfig_reset(cdev->gadget);
- /* standardized runtime overrides for device ID data */
- if (idVendor)
- cdev->desc.idVendor = cpu_to_le16(idVendor);
- if (idProduct)
- cdev->desc.idProduct = cpu_to_le16(idProduct);
- if (bcdDevice)
- cdev->desc.bcdDevice = cpu_to_le16(bcdDevice);
-
/* composite gadget needs to assign strings for whole device (like
* serial number), register function drivers, potentially update
* power state and consumption, etc
@@ -1126,6 +1118,14 @@ static int composite_bind(struct usb_gadget *gadget)
cdev->desc = *composite->dev;
cdev->desc.bMaxPacketSize0 = gadget->ep0->maxpacket;
+ /* standardized runtime overrides for device ID data */
+ if (idVendor)
+ cdev->desc.idVendor = cpu_to_le16(idVendor);
+ if (idProduct)
+ cdev->desc.idProduct = cpu_to_le16(idProduct);
+ if (bcdDevice)
+ cdev->desc.bcdDevice = cpu_to_le16(bcdDevice);
+
/* stirng overrides */
if (iManufacturer || !cdev->desc.iManufacturer) {
if (!iManufacturer && !composite->iManufacturer &&
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 0fae58ef8afe..1d0f45f0e7a6 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -1680,6 +1680,7 @@ static void xhci_add_in_port(struct xhci_hcd *xhci, unsigned int num_ports,
xhci->port_array[i] = (u8) -1;
}
/* FIXME: Should we disable the port? */
+ continue;
}
xhci->port_array[i] = major_revision;
if (major_revision == 0x03)
@@ -1758,16 +1759,20 @@ static int xhci_setup_port_arrays(struct xhci_hcd *xhci, gfp_t flags)
return -ENOMEM;
port_index = 0;
- for (i = 0; i < num_ports; i++)
- if (xhci->port_array[i] != 0x03) {
- xhci->usb2_ports[port_index] =
- &xhci->op_regs->port_status_base +
- NUM_PORT_REGS*i;
- xhci_dbg(xhci, "USB 2.0 port at index %u, "
- "addr = %p\n", i,
- xhci->usb2_ports[port_index]);
- port_index++;
- }
+ for (i = 0; i < num_ports; i++) {
+ if (xhci->port_array[i] == 0x03 ||
+ xhci->port_array[i] == 0 ||
+ xhci->port_array[i] == -1)
+ continue;
+
+ xhci->usb2_ports[port_index] =
+ &xhci->op_regs->port_status_base +
+ NUM_PORT_REGS*i;
+ xhci_dbg(xhci, "USB 2.0 port at index %u, "
+ "addr = %p\n", i,
+ xhci->usb2_ports[port_index]);
+ port_index++;
+ }
}
if (xhci->num_usb3_ports) {
xhci->usb3_ports = kmalloc(sizeof(*xhci->usb3_ports)*
diff --git a/drivers/usb/misc/uss720.c b/drivers/usb/misc/uss720.c
index 796e2f68f749..4ff21587ab03 100644
--- a/drivers/usb/misc/uss720.c
+++ b/drivers/usb/misc/uss720.c
@@ -3,7 +3,7 @@
/*
* uss720.c -- USS720 USB Parport Cable.
*
- * Copyright (C) 1999, 2005
+ * Copyright (C) 1999, 2005, 2010
* Thomas Sailer (t.sailer@alumni.ethz.ch)
*
* This program is free software; you can redistribute it and/or modify
@@ -776,6 +776,8 @@ static const struct usb_device_id uss720_table[] = {
{ USB_DEVICE(0x0557, 0x2001) },
{ USB_DEVICE(0x0729, 0x1284) },
{ USB_DEVICE(0x1293, 0x0002) },
+ { USB_DEVICE(0x1293, 0x0002) },
+ { USB_DEVICE(0x050d, 0x0002) },
{ } /* Terminating entry */
};
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 6a50965e23f2..2dec50013528 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -796,6 +796,7 @@ static struct usb_device_id id_table_combined [] = {
{ USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LOGBOOKML_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LS_LOGBOOK_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_HS_LOGBOOK_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_DOTEC_PID) },
{ USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ }, /* Optional parameter entry */
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 1286f1e23d8c..bf0867285481 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -1081,6 +1081,11 @@
#define MJSG_HD_RADIO_PID 0x937C
/*
+ * D.O.Tec products (http://www.directout.eu)
+ */
+#define FTDI_DOTEC_PID 0x9868
+
+/*
* Xverve Signalyzer tools (http://www.signalyzer.com/)
*/
#define XVERVE_SIGNALYZER_ST_PID 0xBCA0
diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index 6ccdd3dd5259..fcc1e32ce256 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -481,6 +481,13 @@ UNUSUAL_DEV( 0x04e8, 0x507c, 0x0220, 0x0220,
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
US_FL_MAX_SECTORS_64),
+/* Reported by Vitaly Kuznetsov <vitty@altlinux.ru> */
+UNUSUAL_DEV( 0x04e8, 0x5122, 0x0000, 0x9999,
+ "Samsung",
+ "YP-CP3",
+ USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+ US_FL_MAX_SECTORS_64 | US_FL_BULK_IGNORE_TAG),
+
/* Entry and supporting patch by Theodore Kilgore <kilgota@auburn.edu>.
* Device uses standards-violating 32-byte Bulk Command Block Wrappers and
* reports itself as "Proprietary SCSI Bulk." Cf. device entry 0x084d:0x0011.
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-26 19:55:00 +0100