diff options
Diffstat (limited to 'drivers/video/Kconfig')
| -rw-r--r-- | drivers/video/Kconfig | 2476 |
1 files changed, 5 insertions, 2471 deletions
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index 3ad7ebe2a96d..ab05d6cb0796 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -23,6 +23,10 @@ source "drivers/gpu/host1x/Kconfig" source "drivers/gpu/drm/Kconfig" +source "drivers/video/fbdev/Kconfig" + +source "drivers/video/backlight/Kconfig" + config VGASTATE tristate default n @@ -33,2484 +37,14 @@ config VIDEOMODE_HELPERS config HDMI bool -menuconfig FB - tristate "Support for frame buffer devices" - ---help--- - The frame buffer device provides an abstraction for the graphics - hardware. It represents the frame buffer of some video hardware and - allows application software to access the graphics hardware through - a well-defined interface, so the software doesn't need to know - anything about the low-level (hardware register) stuff. - - Frame buffer devices work identically across the different - architectures supported by Linux and make the implementation of - application programs easier and more portable; at this point, an X - server exists which uses the frame buffer device exclusively. - On several non-X86 architectures, the frame buffer device is the - only way to use the graphics hardware. - - The device is accessed through special device nodes, usually located - in the /dev directory, i.e. /dev/fb*. - - You need an utility program called fbset to make full use of frame - buffer devices. Please read <file:Documentation/fb/framebuffer.txt> - and the Framebuffer-HOWTO at - <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.3.html> for more - information. - - Say Y here and to the driver for your graphics board below if you - are compiling a kernel for a non-x86 architecture. - - If you are compiling for the x86 architecture, you can say Y if you - want to play with it, but it is not essential. Please note that - running graphical applications that directly touch the hardware - (e.g. an accelerated X server) and that are not frame buffer - device-aware may cause unexpected results. If unsure, say N. - -config FIRMWARE_EDID - bool "Enable firmware EDID" - depends on FB - default n - ---help--- - This enables access to the EDID transferred from the firmware. - On the i386, this is from the Video BIOS. Enable this if DDC/I2C - transfers do not work for your driver and if you are using - nvidiafb, i810fb or savagefb. - - In general, choosing Y for this option is safe. If you - experience extremely long delays while booting before you get - something on your display, try setting this to N. Matrox cards in - combination with certain motherboards and monitors are known to - suffer from this problem. - -config FB_DDC - tristate - depends on FB - select I2C_ALGOBIT - select I2C - default n - -config FB_BOOT_VESA_SUPPORT - bool - depends on FB - default n - ---help--- - If true, at least one selected framebuffer driver can take advantage - of VESA video modes set at an early boot stage via the vga= parameter. - -config FB_CFB_FILLRECT - tristate - depends on FB - default n - ---help--- - Include the cfb_fillrect function for generic software rectangle - filling. This is used by drivers that don't provide their own - (accelerated) version. - -config FB_CFB_COPYAREA - tristate - depends on FB - default n - ---help--- - Include the cfb_copyarea function for generic software area copying. - This is used by drivers that don't provide their own (accelerated) - version. - -config FB_CFB_IMAGEBLIT - tristate - depends on FB - default n - ---help--- - Include the cfb_imageblit function for generic software image - blitting. This is used by drivers that don't provide their own - (accelerated) version. - -config FB_CFB_REV_PIXELS_IN_BYTE - bool - depends on FB - default n - ---help--- - Allow generic frame-buffer functions to work on displays with 1, 2 - and 4 bits per pixel depths which has opposite order of pixels in - byte order to bytes in long order. - -config FB_SYS_FILLRECT - tristate - depends on FB - default n - ---help--- - Include the sys_fillrect function for generic software rectangle - filling. This is used by drivers that don't provide their own - (accelerated) version and the framebuffer is in system RAM. - -config FB_SYS_COPYAREA - tristate - depends on FB - default n - ---help--- - Include the sys_copyarea function for generic software area copying. - This is used by drivers that don't provide their own (accelerated) - version and the framebuffer is in system RAM. - -config FB_SYS_IMAGEBLIT - tristate - depends on FB - default n - ---help--- - Include the sys_imageblit function for generic software image - blitting. This is used by drivers that don't provide their own - (accelerated) version and the framebuffer is in system RAM. - -menuconfig FB_FOREIGN_ENDIAN - bool "Framebuffer foreign endianness support" - depends on FB - ---help--- - This menu will let you enable support for the framebuffers with - non-native endianness (e.g. Little-Endian framebuffer on a - Big-Endian machine). Most probably you don't have such hardware, - so it's safe to say "n" here. - -choice - prompt "Choice endianness support" - depends on FB_FOREIGN_ENDIAN - -config FB_BOTH_ENDIAN - bool "Support for Big- and Little-Endian framebuffers" - -config FB_BIG_ENDIAN - bool "Support for Big-Endian framebuffers only" - -config FB_LITTLE_ENDIAN - bool "Support for Little-Endian framebuffers only" - -endchoice - -config FB_SYS_FOPS - tristate - depends on FB - default n - -config FB_DEFERRED_IO - bool - depends on FB - -config FB_HECUBA - tristate - depends on FB - depends on FB_DEFERRED_IO - -config FB_SVGALIB - tristate - depends on FB - default n - ---help--- - Common utility functions useful to fbdev drivers of VGA-based - cards. - -config FB_MACMODES - tristate - depends on FB - default n - -config FB_BACKLIGHT - bool - depends on FB - select BACKLIGHT_LCD_SUPPORT - select BACKLIGHT_CLASS_DEVICE - default n - -config FB_MODE_HELPERS - bool "Enable Video Mode Handling Helpers" - depends on FB - default n - ---help--- - This enables functions for handling video modes using the - Generalized Timing Formula and the EDID parser. A few drivers rely - on this feature such as the radeonfb, rivafb, and the i810fb. If - your driver does not take advantage of this feature, choosing Y will - just increase the kernel size by about 5K. - -config FB_TILEBLITTING - bool "Enable Tile Blitting Support" - depends on FB - default n - ---help--- - This enables tile blitting. Tile blitting is a drawing technique - where the screen is divided into rectangular sections (tiles), whereas - the standard blitting divides the screen into pixels. Because the - default drawing element is a tile, drawing functions will be passed - parameters in terms of number of tiles instead of number of pixels. - For example, to draw a single character, instead of using bitmaps, - an index to an array of bitmaps will be used. To clear or move a - rectangular section of a screen, the rectangle will be described in - terms of number of tiles in the x- and y-axis. - - This is particularly important to one driver, matroxfb. If - unsure, say N. - -comment "Frame buffer hardware drivers" - depends on FB - -config FB_GRVGA - tristate "Aeroflex Gaisler framebuffer support" - depends on FB && SPARC - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - This enables support for the SVGACTRL framebuffer in the GRLIB IP library from Aeroflex Gaisler. - -config FB_CIRRUS - tristate "Cirrus Logic support" - depends on FB && (ZORRO || PCI) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - This enables support for Cirrus Logic GD542x/543x based boards on - Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum. - - If you have a PCI-based system, this enables support for these - chips: GD-543x, GD-544x, GD-5480. - - Please read the file <file:Documentation/fb/cirrusfb.txt>. - - Say N unless you have such a graphics board or plan to get one - before you next recompile the kernel. - -config FB_PM2 - tristate "Permedia2 support" - depends on FB && ((AMIGA && BROKEN) || PCI) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for cards based on - the 3D Labs Permedia, Permedia 2 and Permedia 2V chips. - The driver was tested on the following cards: - Diamond FireGL 1000 PRO AGP - ELSA Gloria Synergy PCI - Appian Jeronimo PRO (both heads) PCI - 3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI - Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC - ASK Graphic Blaster Exxtreme AGP - - To compile this driver as a module, choose M here: the - module will be called pm2fb. - -config FB_PM2_FIFO_DISCONNECT - bool "enable FIFO disconnect feature" - depends on FB_PM2 && PCI - help - Support the Permedia2 FIFO disconnect feature. - -config FB_ARMCLCD - tristate "ARM PrimeCell PL110 support" - depends on ARM || ARM64 || COMPILE_TEST - depends on FB && ARM_AMBA - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This framebuffer device driver is for the ARM PrimeCell PL110 - Colour LCD controller. ARM PrimeCells provide the building - blocks for System on a Chip devices. - - If you want to compile this as a module (=code which can be - inserted into and removed from the running kernel), say M - here and read <file:Documentation/kbuild/modules.txt>. The module - will be called amba-clcd. - -config FB_ACORN - bool "Acorn VIDC support" - depends on (FB = y) && ARM && ARCH_ACORN - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the Acorn VIDC graphics - hardware found in Acorn RISC PCs and other ARM-based machines. If - unsure, say N. - -config FB_CLPS711X - bool "CLPS711X LCD support" - depends on (FB = y) && ARM && ARCH_CLPS711X - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Say Y to enable the Framebuffer driver for the CLPS7111 and - EP7212 processors. - -config FB_SA1100 - bool "SA-1100 LCD support" - depends on (FB = y) && ARM && ARCH_SA1100 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is a framebuffer device for the SA-1100 LCD Controller. - See <http://www.linux-fbdev.org/> for information on framebuffer - devices. - - If you plan to use the LCD display with your SA-1100 system, say - Y here. - -config FB_IMX - tristate "Freescale i.MX1/21/25/27 LCD support" - depends on FB && ARCH_MXC - select BACKLIGHT_LCD_SUPPORT - select LCD_CLASS_DEVICE - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MODE_HELPERS - select VIDEOMODE_HELPERS - -config FB_CYBER2000 - tristate "CyberPro 2000/2010/5000 support" - depends on FB && PCI && (BROKEN || !SPARC64) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This enables support for the Integraphics CyberPro 20x0 and 5000 - VGA chips used in the Rebel.com Netwinder and other machines. - Say Y if you have a NetWinder or a graphics card containing this - device, otherwise say N. - -config FB_CYBER2000_DDC - bool "DDC for CyberPro support" - depends on FB_CYBER2000 - select FB_DDC - default y - help - Say Y here if you want DDC support for your CyberPro graphics - card. This is only I2C bus support, driver does not use EDID. - -config FB_CYBER2000_I2C - bool "CyberPro 2000/2010/5000 I2C support" - depends on FB_CYBER2000 && I2C && ARCH_NETWINDER - select I2C_ALGOBIT - help - Enable support for the I2C video decoder interface on the - Integraphics CyberPro 20x0 and 5000 VGA chips. This is used - on the Netwinder machines for the SAA7111 video capture. - -config FB_APOLLO - bool - depends on (FB = y) && APOLLO - default y - select FB_CFB_FILLRECT - select FB_CFB_IMAGEBLIT - -config FB_Q40 - bool - depends on (FB = y) && Q40 - default y - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - -config FB_AMIGA - tristate "Amiga native chipset support" - depends on FB && AMIGA - help - This is the frame buffer device driver for the builtin graphics - chipset found in Amigas. - - To compile this driver as a module, choose M here: the - module will be called amifb. - -config FB_AMIGA_OCS - bool "Amiga OCS chipset support" - depends on FB_AMIGA - help - This enables support for the original Agnus and Denise video chips, - found in the Amiga 1000 and most A500's and A2000's. If you intend - to run Linux on any of these systems, say Y; otherwise say N. - -config FB_AMIGA_ECS - bool "Amiga ECS chipset support" - depends on FB_AMIGA - help - This enables support for the Enhanced Chip Set, found in later - A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If - you intend to run Linux on any of these systems, say Y; otherwise - say N. - -config FB_AMIGA_AGA - bool "Amiga AGA chipset support" - depends on FB_AMIGA - help - This enables support for the Advanced Graphics Architecture (also - known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T - and CD32. If you intend to run Linux on any of these systems, say Y; - otherwise say N. - -config FB_FM2 - bool "Amiga FrameMaster II/Rainbow II support" - depends on (FB = y) && ZORRO - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the Amiga FrameMaster - card from BSC (exhibited 1992 but not shipped as a CBM product). - -config FB_ARC - tristate "Arc Monochrome LCD board support" - depends on FB && X86 - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - help - This enables support for the Arc Monochrome LCD board. The board - is based on the KS-108 lcd controller and is typically a matrix - of 2*n chips. This driver was tested with a 128x64 panel. This - driver supports it for use with x86 SBCs through a 16 bit GPIO - interface (8 bit data, 8 bit control). If you anticipate using - this driver, say Y or M; otherwise say N. You must specify the - GPIO IO address to be used for setting control and data. - -config FB_ATARI - bool "Atari native chipset support" - depends on (FB = y) && ATARI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the builtin graphics - chipset found in Ataris. - -config FB_OF - bool "Open Firmware frame buffer device support" - depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MACMODES - help - Say Y if you want support with Open Firmware for your graphics - board. - -config FB_CONTROL - bool "Apple \"control\" display support" - depends on (FB = y) && PPC_PMAC && PPC32 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MACMODES - help - This driver supports a frame buffer for the graphics adapter in the - Power Macintosh 7300 and others. - -config FB_PLATINUM - bool "Apple \"platinum\" display support" - depends on (FB = y) && PPC_PMAC && PPC32 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MACMODES - help - This driver supports a frame buffer for the "platinum" graphics - adapter in some Power Macintoshes. - -config FB_VALKYRIE - bool "Apple \"valkyrie\" display support" - depends on (FB = y) && (MAC || (PPC_PMAC && PPC32)) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MACMODES - help - This driver supports a frame buffer for the "valkyrie" graphics - adapter in some Power Macintoshes. - -config FB_CT65550 - bool "Chips 65550 display support" - depends on (FB = y) && PPC32 && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the Chips & Technologies - 65550 graphics chip in PowerBooks. - -config FB_ASILIANT - bool "Asiliant (Chips) 69000 display support" - depends on (FB = y) && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the Asiliant 69030 chipset - -config FB_IMSTT - bool "IMS Twin Turbo display support" - depends on (FB = y) && PCI - select FB_CFB_IMAGEBLIT - select FB_MACMODES if PPC - help - The IMS Twin Turbo is a PCI-based frame buffer card bundled with - many Macintosh and compatible computers. - -config FB_VGA16 - tristate "VGA 16-color graphics support" - depends on FB && (X86 || PPC) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select VGASTATE - select FONT_8x16 if FRAMEBUFFER_CONSOLE - help - This is the frame buffer device driver for VGA 16 color graphic - cards. Say Y if you have such a card. - - To compile this driver as a module, choose M here: the - module will be called vga16fb. - -config FB_BF54X_LQ043 - tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)" - depends on FB && (BF54x) && !BF542 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD - -config FB_BFIN_T350MCQB - tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)" - depends on FB && BLACKFIN - select BFIN_GPTIMERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD - This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI - It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK. - -config FB_BFIN_LQ035Q1 - tristate "SHARP LQ035Q1DH02 TFT LCD" - depends on FB && BLACKFIN && SPI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select BFIN_GPTIMERS - help - This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on - the Blackfin Landscape LCD EZ-Extender Card. - This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI - It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK. - - To compile this driver as a module, choose M here: the - module will be called bfin-lq035q1-fb. - -config FB_BF537_LQ035 - tristate "SHARP LQ035 TFT LCD (BF537 STAMP)" - depends on FB && (BF534 || BF536 || BF537) && I2C_BLACKFIN_TWI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select BFIN_GPTIMERS - help - This is the framebuffer device for a SHARP LQ035Q7DB03 TFT LCD - attached to a BF537. - - To compile this driver as a module, choose M here: the - module will be called bf537-lq035. - -config FB_BFIN_7393 - tristate "Blackfin ADV7393 Video encoder" - depends on FB && BLACKFIN - select I2C - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the framebuffer device for a ADV7393 video encoder - attached to a Blackfin on the PPI port. - If your Blackfin board has a ADV7393 select Y. - - To compile this driver as a module, choose M here: the - module will be called bfin_adv7393fb. - -choice - prompt "Video mode support" - depends on FB_BFIN_7393 - default NTSC - -config NTSC - bool 'NTSC 720x480' - -config PAL - bool 'PAL 720x576' - -config NTSC_640x480 - bool 'NTSC 640x480 (Experimental)' - -config PAL_640x480 - bool 'PAL 640x480 (Experimental)' - -config NTSC_YCBCR - bool 'NTSC 720x480 YCbCR input' - -config PAL_YCBCR - bool 'PAL 720x576 YCbCR input' - -endchoice - -choice - prompt "Size of ADV7393 frame buffer memory Single/Double Size" - depends on (FB_BFIN_7393) - default ADV7393_1XMEM - -config ADV7393_1XMEM - bool 'Single' - -config ADV7393_2XMEM - bool 'Double' -endchoice - -config FB_STI - tristate "HP STI frame buffer device support" - depends on FB && PARISC - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select STI_CONSOLE - select VT - default y - ---help--- - STI refers to the HP "Standard Text Interface" which is a set of - BIOS routines contained in a ROM chip in HP PA-RISC based machines. - Enabling this option will implement the linux framebuffer device - using calls to the STI BIOS routines for initialisation. - - If you enable this option, you will get a planar framebuffer device - /dev/fb which will work on the most common HP graphic cards of the - NGLE family, including the artist chips (in the 7xx and Bxxx series), - HCRX, HCRX24, CRX, CRX24 and VisEG series. - - It is safe to enable this option, so you should probably say "Y". - -config FB_MAC - bool "Generic Macintosh display support" - depends on (FB = y) && MAC - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MACMODES - -config FB_HP300 - bool - depends on (FB = y) && DIO - select FB_CFB_IMAGEBLIT - default y - -config FB_TGA - tristate "TGA/SFB+ framebuffer support" - depends on FB && (ALPHA || TC) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select BITREVERSE - ---help--- - This is the frame buffer device driver for generic TGA and SFB+ - graphic cards. These include DEC ZLXp-E1, -E2 and -E3 PCI cards, - also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3 - TURBOchannel cards, also known as PMAGD-A, -B and -C. - - Due to hardware limitations ZLX-E2 and E3 cards are not supported - for DECstation 5000/200 systems. Additionally due to firmware - limitations these cards may cause troubles with booting DECstation - 5000/240 and /260 systems, but are fully supported under Linux if - you manage to get it going. ;-) - - Say Y if you have one of those. - -config FB_UVESA - tristate "Userspace VESA VGA graphics support" - depends on FB && CONNECTOR - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MODE_HELPERS - help - This is the frame buffer driver for generic VBE 2.0 compliant - graphic cards. It can also take advantage of VBE 3.0 features, - such as refresh rate adjustment. - - This driver generally provides more features than vesafb but - requires a userspace helper application called 'v86d'. See - <file:Documentation/fb/uvesafb.txt> for more information. - - If unsure, say N. - -config FB_VESA - bool "VESA VGA graphics support" - depends on (FB = y) && X86 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_BOOT_VESA_SUPPORT - help - This is the frame buffer device driver for generic VESA 2.0 - compliant graphic cards. The older VESA 1.2 cards are not supported. - You will get a boot time penguin logo at no additional cost. Please - read <file:Documentation/fb/vesafb.txt>. If unsure, say Y. - -config FB_EFI - bool "EFI-based Framebuffer Support" - depends on (FB = y) && X86 && EFI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the EFI frame buffer device driver. If the firmware on - your platform is EFI 1.10 or UEFI 2.0, select Y to add support for - using the EFI framebuffer as your console. - -config FB_N411 - tristate "N411 Apollo/Hecuba devkit support" - depends on FB && X86 && MMU - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select FB_DEFERRED_IO - select FB_HECUBA - help - This enables support for the Apollo display controller in its - Hecuba form using the n411 devkit. - -config FB_HGA - tristate "Hercules mono graphics support" - depends on FB && X86 - help - Say Y here if you have a Hercules mono graphics card. - - To compile this driver as a module, choose M here: the - module will be called hgafb. - - As this card technology is at least 25 years old, - most people will answer N here. - -config FB_GBE - bool "SGI Graphics Backend frame buffer support" - depends on (FB = y) && SGI_IP32 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for SGI Graphics Backend. - This chip is used in SGI O2 and Visual Workstation 320/540. - -config FB_GBE_MEM - int "Video memory size in MB" - depends on FB_GBE - default 4 - help - This is the amount of memory reserved for the framebuffer, - which can be any value between 1MB and 8MB. - -config FB_SBUS - bool "SBUS and UPA framebuffers" - depends on (FB = y) && SPARC - help - Say Y if you want support for SBUS or UPA based frame buffer device. - -config FB_BW2 - bool "BWtwo support" - depends on (FB = y) && (SPARC && FB_SBUS) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the BWtwo frame buffer. - -config FB_CG3 - bool "CGthree support" - depends on (FB = y) && (SPARC && FB_SBUS) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the CGthree frame buffer. - -config FB_CG6 - bool "CGsix (GX,TurboGX) support" - depends on (FB = y) && (SPARC && FB_SBUS) - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the CGsix (GX, TurboGX) - frame buffer. - -config FB_FFB - bool "Creator/Creator3D/Elite3D support" - depends on FB_SBUS && SPARC64 - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the Creator, Creator3D, - and Elite3D graphics boards. - -config FB_TCX - bool "TCX (SS4/SS5 only) support" - depends on FB_SBUS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the TCX 24/8bit frame - buffer. - -config FB_CG14 - bool "CGfourteen (SX) support" - depends on FB_SBUS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the CGfourteen frame - buffer on Desktop SPARCsystems with the SX graphics option. - -config FB_P9100 - bool "P9100 (Sparcbook 3 only) support" - depends on FB_SBUS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the P9100 card - supported on Sparcbook 3 machines. - -config FB_LEO - bool "Leo (ZX) support" - depends on FB_SBUS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the SBUS-based Sun ZX - (leo) frame buffer cards. - -config FB_IGA - bool "IGA 168x display support" - depends on (FB = y) && SPARC32 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the framebuffer device for the INTERGRAPHICS 1680 and - successor frame buffer cards. - -config FB_XVR500 - bool "Sun XVR-500 3DLABS Wildcat support" - depends on (FB = y) && PCI && SPARC64 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the framebuffer device for the Sun XVR-500 and similar - graphics cards based upon the 3DLABS Wildcat chipset. The driver - only works on sparc64 systems where the system firmware has - mostly initialized the card already. It is treated as a - completely dumb framebuffer device. - -config FB_XVR2500 - bool "Sun XVR-2500 3DLABS Wildcat support" - depends on (FB = y) && PCI && SPARC64 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the framebuffer device for the Sun XVR-2500 and similar - graphics cards based upon the 3DLABS Wildcat chipset. The driver - only works on sparc64 systems where the system firmware has - mostly initialized the card already. It is treated as a - completely dumb framebuffer device. - -config FB_XVR1000 - bool "Sun XVR-1000 support" - depends on (FB = y) && SPARC64 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the framebuffer device for the Sun XVR-1000 and similar - graphics cards. The driver only works on sparc64 systems where - the system firmware has mostly initialized the card already. It - is treated as a completely dumb framebuffer device. - -config FB_PVR2 - tristate "NEC PowerVR 2 display support" - depends on FB && SH_DREAMCAST - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Say Y here if you have a PowerVR 2 card in your box. If you plan to - run linux on your Dreamcast, you will have to say Y here. - This driver may or may not work on other PowerVR 2 cards, but is - totally untested. Use at your own risk. If unsure, say N. - - To compile this driver as a module, choose M here: the - module will be called pvr2fb. - - You can pass several parameters to the driver at boot time or at - module load time. The parameters look like "video=pvr2:XXX", where - the meaning of XXX can be found at the end of the main source file - (<file:drivers/video/pvr2fb.c>). Please see the file - <file:Documentation/fb/pvr2fb.txt>. - -config FB_OPENCORES - tristate "OpenCores VGA/LCD core 2.0 framebuffer support" - depends on FB && HAS_DMA - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This enables support for the OpenCores VGA/LCD core. - - The OpenCores VGA/LCD core is typically used together with - softcore CPUs (e.g. OpenRISC or Microblaze) or hard processor - systems (e.g. Altera socfpga or Xilinx Zynq) on FPGAs. - - The source code and specification for the core is available at - <http://opencores.org/project,vga_lcd> - -config FB_S1D13XXX - tristate "Epson S1D13XXX framebuffer support" - depends on FB - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Support for S1D13XXX framebuffer device family (currently only - working with S1D13806). Product specs at - <http://vdc.epson.com/> - -config FB_ATMEL - tristate "AT91/AT32 LCD Controller support" - depends on FB && HAVE_FB_ATMEL - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MODE_HELPERS - select VIDEOMODE_HELPERS - help - This enables support for the AT91/AT32 LCD Controller. - -config FB_INTSRAM - bool "Frame Buffer in internal SRAM" - depends on FB_ATMEL && ARCH_AT91SAM9261 - help - Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want - to let frame buffer in external SDRAM. - -config FB_ATMEL_STN - bool "Use a STN display with AT91/AT32 LCD Controller" - depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK) - default n - help - Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD - Controller. Say N if you want to connect a TFT. - - If unsure, say N. - -config FB_NVIDIA - tristate "nVidia Framebuffer Support" - depends on FB && PCI - select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select BITREVERSE - select VGASTATE - help - This driver supports graphics boards with the nVidia chips, TNT - and newer. For very old chipsets, such as the RIVA128, then use - the rivafb. - Say Y if you have such a graphics board. - - To compile this driver as a module, choose M here: the - module will be called nvidiafb. - -config FB_NVIDIA_I2C - bool "Enable DDC Support" - depends on FB_NVIDIA - select FB_DDC - help - This enables I2C support for nVidia Chipsets. This is used - only for getting EDID information from the attached display - allowing for robust video mode handling and switching. - - Because fbdev-2.6 requires that drivers must be able to - independently validate video mode parameters, you should say Y - here. - -config FB_NVIDIA_DEBUG - bool "Lots of debug output" - depends on FB_NVIDIA - default n - help - Say Y here if you want the nVidia driver to output all sorts - of debugging information to provide to the maintainer when - something goes wrong. - -config FB_NVIDIA_BACKLIGHT - bool "Support for backlight control" - depends on FB_NVIDIA - default y - help - Say Y here if you want to control the backlight of your display. - -config FB_RIVA - tristate "nVidia Riva support" - depends on FB && PCI - select FB_BACKLIGHT if FB_RIVA_BACKLIGHT - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select BITREVERSE - select VGASTATE - help - This driver supports graphics boards with the nVidia Riva/Geforce - chips. - Say Y if you have such a graphics board. - - To compile this driver as a module, choose M here: the - module will be called rivafb. - -config FB_RIVA_I2C - bool "Enable DDC Support" - depends on FB_RIVA - select FB_DDC - help - This enables I2C support for nVidia Chipsets. This is used - only for getting EDID information from the attached display - allowing for robust video mode handling and switching. - - Because fbdev-2.6 requires that drivers must be able to - independently validate video mode parameters, you should say Y - here. - -config FB_RIVA_DEBUG - bool "Lots of debug output" - depends on FB_RIVA - default n - help - Say Y here if you want the Riva driver to output all sorts - of debugging information to provide to the maintainer when - something goes wrong. - -config FB_RIVA_BACKLIGHT - bool "Support for backlight control" - depends on FB_RIVA - default y - help - Say Y here if you want to control the backlight of your display. - -config FB_I740 - tristate "Intel740 support" - depends on FB && PCI - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select VGASTATE - select FB_DDC - help - This driver supports graphics cards based on Intel740 chip. - -config FB_I810 - tristate "Intel 810/815 support" - depends on FB && PCI && X86_32 && AGP_INTEL - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select VGASTATE - help - This driver supports the on-board graphics built in to the Intel 810 - and 815 chipsets. Say Y if you have and plan to use such a board. - - To compile this driver as a module, choose M here: the - module will be called i810fb. - - For more information, please read - <file:Documentation/fb/intel810.txt> - -config FB_I810_GTF - bool "use VESA Generalized Timing Formula" - depends on FB_I810 - help - If you say Y, then the VESA standard, Generalized Timing Formula - or GTF, will be used to calculate the required video timing values - per video mode. Since the GTF allows nondiscrete timings - (nondiscrete being a range of values as opposed to discrete being a - set of values), you'll be able to use any combination of horizontal - and vertical resolutions, and vertical refresh rates without having - to specify your own timing parameters. This is especially useful - to maximize the performance of an aging display, or if you just - have a display with nonstandard dimensions. A VESA compliant - monitor is recommended, but can still work with non-compliant ones. - If you need or want this, then select this option. The timings may - not be compliant with Intel's recommended values. Use at your own - risk. - - If you say N, the driver will revert to discrete video timings - using a set recommended by Intel in their documentation. - - If unsure, say N. - -config FB_I810_I2C - bool "Enable DDC Support" - depends on FB_I810 && FB_I810_GTF - select FB_DDC - help - -config FB_LE80578 - tristate "Intel LE80578 (Vermilion) support" - depends on FB && PCI && X86 - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This driver supports the LE80578 (Vermilion Range) chipset - -config FB_CARILLO_RANCH - tristate "Intel Carillo Ranch support" - depends on FB_LE80578 && FB && PCI && X86 - help - This driver supports the LE80578 (Carillo Ranch) board - -config FB_INTEL - tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support" - depends on FB && PCI && X86 && AGP_INTEL && EXPERT - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_BOOT_VESA_SUPPORT if FB_INTEL = y - depends on !DRM_I915 - help - This driver supports the on-board graphics built in to the Intel - 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets. - Say Y if you have and plan to use such a board. - - To make FB_INTELFB=Y work you need to say AGP_INTEL=y too. - - To compile this driver as a module, choose M here: the - module will be called intelfb. - - For more information, please read <file:Documentation/fb/intelfb.txt> - -config FB_INTEL_DEBUG - bool "Intel driver Debug Messages" - depends on FB_INTEL - ---help--- - Say Y here if you want the Intel driver to output all sorts - of debugging information to provide to the maintainer when - something goes wrong. - -config FB_INTEL_I2C - bool "DDC/I2C for Intel framebuffer support" - depends on FB_INTEL - select FB_DDC - default y - help - Say Y here if you want DDC/I2C support for your on-board Intel graphics. - -config FB_MATROX - tristate "Matrox acceleration" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_TILEBLITTING - select FB_MACMODES if PPC_PMAC - ---help--- - Say Y here if you have a Matrox Millennium, Matrox Millennium II, - Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox - Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video, - Matrox G400, G450 or G550 card in your box. - - To compile this driver as a module, choose M here: the - module will be called matroxfb. - - You can pass several parameters to the driver at boot time or at - module load time. The parameters look like "video=matroxfb:XXX", and - are described in <file:Documentation/fb/matroxfb.txt>. - -config FB_MATROX_MILLENIUM - bool "Millennium I/II support" - depends on FB_MATROX - help - Say Y here if you have a Matrox Millennium or Matrox Millennium II - video card. If you select "Advanced lowlevel driver options" below, - you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp - packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can - also use font widths different from 8. - -config FB_MATROX_MYSTIQUE - bool "Mystique support" - depends on FB_MATROX - help - Say Y here if you have a Matrox Mystique or Matrox Mystique 220 - video card. If you select "Advanced lowlevel driver options" below, - you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp - packed pixel and 32 bpp packed pixel. You can also use font widths - different from 8. - -config FB_MATROX_G - bool "G100/G200/G400/G450/G550 support" - depends on FB_MATROX - ---help--- - Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based - video card. If you select "Advanced lowlevel driver options", you - should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed - pixel and 32 bpp packed pixel. You can also use font widths - different from 8. - - If you need support for G400 secondary head, you must say Y to - "Matrox I2C support" and "G400 second head support" right below. - G450/G550 secondary head and digital output are supported without - additional modules. - - The driver starts in monitor mode. You must use the matroxset tool - (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to - swap primary and secondary head outputs, or to change output mode. - Secondary head driver always start in 640x480 resolution and you - must use fbset to change it. - - Do not forget that second head supports only 16 and 32 bpp - packed pixels, so it is a good idea to compile them into the kernel - too. You can use only some font widths, as the driver uses generic - painting procedures (the secondary head does not use acceleration - engine). - - G450/G550 hardware can display TV picture only from secondary CRTC, - and it performs no scaling, so picture must have 525 or 625 lines. - -config FB_MATROX_I2C - tristate "Matrox I2C support" - depends on FB_MATROX - select FB_DDC - ---help--- - This drivers creates I2C buses which are needed for accessing the - DDC (I2C) bus present on all Matroxes, an I2C bus which - interconnects Matrox optional devices, like MGA-TVO on G200 and - G400, and the secondary head DDC bus, present on G400 only. - - You can say Y or M here if you want to experiment with monitor - detection code. You must say Y or M here if you want to use either - second head of G400 or MGA-TVO on G200 or G400. - - If you compile it as module, it will create a module named - i2c-matroxfb. - -config FB_MATROX_MAVEN - tristate "G400 second head support" - depends on FB_MATROX_G && FB_MATROX_I2C - ---help--- - WARNING !!! This support does not work with G450 !!! - - Say Y or M here if you want to use a secondary head (meaning two - monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary - head is not compatible with accelerated XFree 3.3.x SVGA servers - - secondary head output is blanked while you are in X. With XFree - 3.9.17 preview you can use both heads if you use SVGA over fbdev or - the fbdev driver on first head and the fbdev driver on second head. - - If you compile it as module, two modules are created, - matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for - both G200 and G400, matroxfb_crtc2 is needed only by G400. You must - also load i2c-matroxfb to get it to run. - - The driver starts in monitor mode and you must use the matroxset - tool (available at - <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to - PAL or NTSC or to swap primary and secondary head outputs. - Secondary head driver also always start in 640x480 resolution, you - must use fbset to change it. - - Also do not forget that second head supports only 16 and 32 bpp - packed pixels, so it is a good idea to compile them into the kernel - too. You can use only some font widths, as the driver uses generic - painting procedures (the secondary head does not use acceleration - engine). - -config FB_RADEON - tristate "ATI Radeon display support" - depends on FB && PCI - select FB_BACKLIGHT if FB_RADEON_BACKLIGHT - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MACMODES if PPC_OF - help - Choose this option if you want to use an ATI Radeon graphics card as - a framebuffer device. There are both PCI and AGP versions. You - don't need to choose this to run the Radeon in plain VGA mode. - - There is a product page at - http://products.amd.com/en-us/GraphicCardResult.aspx - -config FB_RADEON_I2C - bool "DDC/I2C for ATI Radeon support" - depends on FB_RADEON - select FB_DDC - default y - help - Say Y here if you want DDC/I2C support for your Radeon board. - -config FB_RADEON_BACKLIGHT - bool "Support for backlight control" - depends on FB_RADEON - default y - help - Say Y here if you want to control the backlight of your display. - -config FB_RADEON_DEBUG - bool "Lots of debug output from Radeon driver" - depends on FB_RADEON - default n - help - Say Y here if you want the Radeon driver to output all sorts - of debugging information to provide to the maintainer when - something goes wrong. - -config FB_ATY128 - tristate "ATI Rage128 display support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_BACKLIGHT if FB_ATY128_BACKLIGHT - select FB_MACMODES if PPC_PMAC - help - This driver supports graphics boards with the ATI Rage128 chips. - Say Y if you have such a graphics board and read - <file:Documentation/fb/aty128fb.txt>. - - To compile this driver as a module, choose M here: the - module will be called aty128fb. - -config FB_ATY128_BACKLIGHT - bool "Support for backlight control" - depends on FB_ATY128 - default y - help - Say Y here if you want to control the backlight of your display. - -config FB_ATY - tristate "ATI Mach64 display support" if PCI || ATARI - depends on FB && !SPARC32 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_BACKLIGHT if FB_ATY_BACKLIGHT - select FB_MACMODES if PPC - help - This driver supports graphics boards with the ATI Mach64 chips. - Say Y if you have such a graphics board. - - To compile this driver as a module, choose M here: the - module will be called atyfb. - -config FB_ATY_CT - bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support" - depends on PCI && FB_ATY - default y if SPARC64 && PCI - help - Say Y here to support use of ATI's 64-bit Rage boards (or other - boards based on the Mach64 CT, VT, GT, and LT chipsets) as a - framebuffer device. The ATI product support page for these boards - is at <http://support.ati.com/products/pc/mach64/mach64.html>. - -config FB_ATY_GENERIC_LCD - bool "Mach64 generic LCD support" - depends on FB_ATY_CT - help - Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility, - Rage XC, or Rage XL chipset. - -config FB_ATY_GX - bool "Mach64 GX support" if PCI - depends on FB_ATY - default y if ATARI - help - Say Y here to support use of the ATI Mach64 Graphics Expression - board (or other boards based on the Mach64 GX chipset) as a - framebuffer device. The ATI product support page for these boards - is at - <http://support.ati.com/products/pc/mach64/graphics_xpression.html>. - -config FB_ATY_BACKLIGHT - bool "Support for backlight control" - depends on FB_ATY - default y - help - Say Y here if you want to control the backlight of your display. - -config FB_S3 - tristate "S3 Trio/Virge support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_TILEBLITTING - select FB_SVGALIB - select VGASTATE - select FONT_8x16 if FRAMEBUFFER_CONSOLE - ---help--- - Driver for graphics boards with S3 Trio / S3 Virge chip. - -config FB_S3_DDC - bool "DDC for S3 support" - depends on FB_S3 - select FB_DDC - default y - help - Say Y here if you want DDC support for your S3 graphics card. - -config FB_SAVAGE - tristate "S3 Savage support" - depends on FB && PCI - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select VGASTATE - help - This driver supports notebooks and computers with S3 Savage PCI/AGP - chips. - - Say Y if you have such a graphics card. - - To compile this driver as a module, choose M here; the module - will be called savagefb. - -config FB_SAVAGE_I2C - bool "Enable DDC2 Support" - depends on FB_SAVAGE - select FB_DDC - help - This enables I2C support for S3 Savage Chipsets. This is used - only for getting EDID information from the attached display - allowing for robust video mode handling and switching. - - Because fbdev-2.6 requires that drivers must be able to - independently validate video mode parameters, you should say Y - here. - -config FB_SAVAGE_ACCEL - bool "Enable Console Acceleration" - depends on FB_SAVAGE - default n - help - This option will compile in console acceleration support. If - the resulting framebuffer console has bothersome glitches, then - choose N here. - -config FB_SIS - tristate "SiS/XGI display support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_BOOT_VESA_SUPPORT if FB_SIS = y - help - This is the frame buffer device driver for the SiS 300, 315, 330 - and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets. - Specs available at <http://www.sis.com> and <http://www.xgitech.com>. - - To compile this driver as a module, choose M here; the module - will be called sisfb. - -config FB_SIS_300 - bool "SiS 300 series support" - depends on FB_SIS - help - Say Y here to support use of the SiS 300/305, 540, 630 and 730. - -config FB_SIS_315 - bool "SiS 315/330/340 series and XGI support" - depends on FB_SIS - help - Say Y here to support use of the SiS 315, 330 and 340 series - (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well - as XGI V3XT, V5, V8 and Z7. - -config FB_VIA - tristate "VIA UniChrome (Pro) and Chrome9 display support" - depends on FB && PCI && X86 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select I2C_ALGOBIT - select I2C - select GPIOLIB - help - This is the frame buffer device driver for Graphics chips of VIA - UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/ - CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896 - /P4M900,VX800) - Say Y if you have a VIA UniChrome graphics board. - - To compile this driver as a module, choose M here: the - module will be called viafb. - -if FB_VIA - -config FB_VIA_DIRECT_PROCFS - bool "direct hardware access via procfs (DEPRECATED)(DANGEROUS)" - depends on FB_VIA - default n - help - Allow direct hardware access to some output registers via procfs. - This is dangerous but may provide the only chance to get the - correct output device configuration. - Its use is strongly discouraged. - -config FB_VIA_X_COMPATIBILITY - bool "X server compatibility" - depends on FB_VIA - default n - help - This option reduces the functionality (power saving, ...) of the - framebuffer to avoid negative impact on the OpenChrome X server. - If you use any X server other than fbdev you should enable this - otherwise it should be safe to disable it and allow using all - features. - -endif - -config FB_NEOMAGIC - tristate "NeoMagic display support" - depends on FB && PCI - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select VGASTATE - help - This driver supports notebooks with NeoMagic PCI chips. - Say Y if you have such a graphics card. - - To compile this driver as a module, choose M here: the - module will be called neofb. - -config FB_KYRO - tristate "IMG Kyro support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Say Y here if you have a STG4000 / Kyro / PowerVR 3 based - graphics board. - - To compile this driver as a module, choose M here: the - module will be called kyrofb. - -config FB_3DFX - tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support" - depends on FB && PCI - select FB_CFB_IMAGEBLIT - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_MODE_HELPERS - help - This driver supports graphics boards with the 3Dfx Banshee, - Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have - such a graphics board. - - To compile this driver as a module, choose M here: the - module will be called tdfxfb. - -config FB_3DFX_ACCEL - bool "3Dfx Acceleration functions" - depends on FB_3DFX - ---help--- - This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer - device driver with acceleration functions. - -config FB_3DFX_I2C - bool "Enable DDC/I2C support" - depends on FB_3DFX - select FB_DDC - default y - help - Say Y here if you want DDC/I2C support for your 3dfx Voodoo3. - -config FB_VOODOO1 - tristate "3Dfx Voodoo Graphics (sst1) support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or - Voodoo2 (cvg) based graphics card. - - To compile this driver as a module, choose M here: the - module will be called sstfb. - - WARNING: Do not use any application that uses the 3D engine - (namely glide) while using this driver. - Please read the <file:Documentation/fb/sstfb.txt> for supported - options and other important info support. - -config FB_VT8623 - tristate "VIA VT8623 support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_TILEBLITTING - select FB_SVGALIB - select VGASTATE - select FONT_8x16 if FRAMEBUFFER_CONSOLE - ---help--- - Driver for CastleRock integrated graphics core in the - VIA VT8623 [Apollo CLE266] chipset. - -config FB_TRIDENT - tristate "Trident/CyberXXX/CyberBlade support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - This is the frame buffer device driver for Trident PCI/AGP chipsets. - Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D - and Blade XP. - There are also integrated versions of these chips called CyberXXXX, - CyberImage or CyberBlade. These chips are mostly found in laptops - but also on some motherboards including early VIA EPIA motherboards. - For more information, read <file:Documentation/fb/tridentfb.txt> - - Say Y if you have such a graphics board. - - To compile this driver as a module, choose M here: the - module will be called tridentfb. - -config FB_ARK - tristate "ARK 2000PV support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_TILEBLITTING - select FB_SVGALIB - select VGASTATE - select FONT_8x16 if FRAMEBUFFER_CONSOLE - ---help--- - Driver for PCI graphics boards with ARK 2000PV chip - and ICS 5342 RAMDAC. - -config FB_PM3 - tristate "Permedia3 support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the 3DLabs Permedia3 - chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 & - similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000 - and maybe other boards. - -config FB_CARMINE - tristate "Fujitsu carmine frame buffer support" - depends on FB && PCI - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the Fujitsu Carmine chip. - The driver provides two independent frame buffer devices. - -choice - depends on FB_CARMINE - prompt "DRAM timing" - default FB_CARMINE_DRAM_EVAL - -config FB_CARMINE_DRAM_EVAL - bool "Eval board timings" - help - Use timings which work on the eval card. - -config CARMINE_DRAM_CUSTOM - bool "Custom board timings" - help - Use custom board timings. -endchoice - -config FB_AU1100 - bool "Au1100 LCD Driver" - depends on (FB = y) && MIPS_ALCHEMY - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the framebuffer driver for the AMD Au1100 SOC. It can drive - various panels and CRTs by passing in kernel cmd line option - au1100fb:panel=<name>. - -config FB_AU1200 - bool "Au1200/Au1300 LCD Driver" - depends on (FB = y) && MIPS_ALCHEMY - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - help - This is the framebuffer driver for the Au1200/Au1300 SOCs. - It can drive various panels and CRTs by passing in kernel cmd line - option au1200fb:panel=<name>. - -config FB_VT8500 - bool "VIA VT8500 framebuffer support" - depends on (FB = y) && ARM && ARCH_VT8500 - select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS) - select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS) - select FB_SYS_IMAGEBLIT - select FB_MODE_HELPERS - select VIDEOMODE_HELPERS - help - This is the framebuffer driver for VIA VT8500 integrated LCD - controller. - -config FB_WM8505 - bool "Wondermedia WM8xxx-series frame buffer support" - depends on (FB = y) && ARM && ARCH_VT8500 - select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS) - select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS) - select FB_SYS_IMAGEBLIT - select FB_MODE_HELPERS - select VIDEOMODE_HELPERS - help - This is the framebuffer driver for WonderMedia WM8xxx-series - integrated LCD controller. This driver covers the WM8505, WM8650 - and WM8850 SoCs. - -config FB_WMT_GE_ROPS - bool "VT8500/WM8xxx accelerated raster ops support" - depends on (FB = y) && (FB_VT8500 || FB_WM8505) - default n - help - This adds support for accelerated raster operations on the - VIA VT8500 and Wondermedia 85xx series SoCs. - -source "drivers/video/geode/Kconfig" - -config FB_HIT - tristate "HD64461 Frame Buffer support" - depends on FB && HD64461 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This is the frame buffer device driver for the Hitachi HD64461 LCD - frame buffer card. - -config FB_PMAG_AA - bool "PMAG-AA TURBOchannel framebuffer support" - depends on (FB = y) && TC - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1) - used mainly in the MIPS-based DECstation series. - -config FB_PMAG_BA - tristate "PMAG-BA TURBOchannel framebuffer support" - depends on FB && TC - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8) - used mainly in the MIPS-based DECstation series. - -config FB_PMAGB_B - tristate "PMAGB-B TURBOchannel framebuffer support" - depends on FB && TC - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Support for the PMAGB-B TURBOchannel framebuffer card used mainly - in the MIPS-based DECstation series. The card is currently only - supported in 1280x1024x8 mode. - -config FB_MAXINE - bool "Maxine (Personal DECstation) onboard framebuffer support" - depends on (FB = y) && MACH_DECSTATION - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Support for the onboard framebuffer (1024x768x8) in the Personal - DECstation series (Personal DECstation 5000/20, /25, /33, /50, - Codename "Maxine"). - -config FB_G364 - bool "G364 frame buffer support" - depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - The G364 driver is the framebuffer used in MIPS Magnum 4000 and - Olivetti M700-10 systems. - -config FB_68328 - bool "Motorola 68328 native frame buffer support" - depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Say Y here if you want to support the built-in frame buffer of - the Motorola 68328 CPU family. - -config FB_PXA168 - tristate "PXA168/910 LCD framebuffer support" - depends on FB && (CPU_PXA168 || CPU_PXA910) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for the built-in LCD controller in the Marvell - MMP processor. - -config FB_PXA - tristate "PXA LCD framebuffer support" - depends on FB && ARCH_PXA - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for the built-in LCD controller in the Intel - PXA2x0 processor. - - This driver is also available as a module ( = code which can be - inserted and removed from the running kernel whenever you want). The - module will be called pxafb. If you want to compile it as a module, - say M here and read <file:Documentation/kbuild/modules.txt>. - - If unsure, say N. - -config FB_PXA_OVERLAY - bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer" - default n - depends on FB_PXA && (PXA27x || PXA3xx) - -config FB_PXA_SMARTPANEL - bool "PXA Smartpanel LCD support" - default n - depends on FB_PXA - -config FB_PXA_PARAMETERS - bool "PXA LCD command line parameters" - default n - depends on FB_PXA - ---help--- - Enable the use of kernel command line or module parameters - to configure the physical properties of the LCD panel when - using the PXA LCD driver. - - This option allows you to override the panel parameters - supplied by the platform in order to support multiple - different models of flatpanel. If you will only be using a - single model of flatpanel then you can safely leave this - option disabled. - - <file:Documentation/fb/pxafb.txt> describes the available parameters. - -config PXA3XX_GCU - tristate "PXA3xx 2D graphics accelerator driver" - depends on FB_PXA - help - Kernelspace driver for the 2D graphics controller unit (GCU) - found on PXA3xx processors. There is a counterpart driver in the - DirectFB suite, see http://www.directfb.org/ - - If you compile this as a module, it will be called pxa3xx_gcu. - -config FB_MBX - tristate "2700G LCD framebuffer support" - depends on FB && ARCH_PXA - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Framebuffer driver for the Intel 2700G (Marathon) Graphics - Accelerator - -config FB_MBX_DEBUG - bool "Enable debugging info via debugfs" - depends on FB_MBX && DEBUG_FS - default n - ---help--- - Enable this if you want debugging information using the debug - filesystem (debugfs) - - If unsure, say N. - -config FB_FSL_DIU - tristate "Freescale DIU framebuffer support" - depends on FB && FSL_SOC - select FB_MODE_HELPERS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select PPC_LIB_RHEAP - ---help--- - Framebuffer driver for the Freescale SoC DIU - -config FB_W100 - tristate "W100 frame buffer support" - depends on FB && ARCH_PXA - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for the w100 as found on the Sharp SL-Cxx series. - It can also drive the w3220 chip found on iPAQ hx4700. - - This driver is also available as a module ( = code which can be - inserted and removed from the running kernel whenever you want). The - module will be called w100fb. If you want to compile it as a module, - say M here and read <file:Documentation/kbuild/modules.txt>. - - If unsure, say N. - -config FB_SH_MOBILE_LCDC - tristate "SuperH Mobile LCDC framebuffer support" - depends on FB && (SUPERH || ARCH_SHMOBILE) && HAVE_CLK - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select FB_DEFERRED_IO - select FB_BACKLIGHT - select SH_MIPI_DSI if SH_LCD_MIPI_DSI - ---help--- - Frame buffer driver for the on-chip SH-Mobile LCD controller. - -config FB_SH_MOBILE_HDMI - tristate "SuperH Mobile HDMI controller support" - depends on FB_SH_MOBILE_LCDC - select FB_MODE_HELPERS - select SOUND - select SND - select SND_SOC - ---help--- - Driver for the on-chip SH-Mobile HDMI controller. - -config FB_TMIO - tristate "Toshiba Mobile IO FrameBuffer support" - depends on FB && MFD_CORE - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for the Toshiba Mobile IO integrated as found - on the Sharp SL-6000 series - - This driver is also available as a module ( = code which can be - inserted and removed from the running kernel whenever you want). The - module will be called tmiofb. If you want to compile it as a module, - say M here and read <file:Documentation/kbuild/modules.txt>. - - If unsure, say N. - -config FB_TMIO_ACCELL - bool "tmiofb acceleration" - depends on FB_TMIO - default y - -config FB_S3C - tristate "Samsung S3C framebuffer support" - depends on FB && (CPU_S3C2416 || ARCH_S3C64XX || ARCH_S5P64X0 || \ - ARCH_S5PC100 || ARCH_S5PV210 || ARCH_EXYNOS) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for the built-in FB controller in the Samsung - SoC line from the S3C2443 onwards, including the S3C2416, S3C2450, - and the S3C64XX series such as the S3C6400 and S3C6410. - - These chips all have the same basic framebuffer design with the - actual capabilities depending on the chip. For instance the S3C6400 - and S3C6410 support 4 hardware windows whereas the S3C24XX series - currently only have two. - - Currently the support is only for the S3C6400 and S3C6410 SoCs. - -config FB_S3C_DEBUG_REGWRITE - bool "Debug register writes" - depends on FB_S3C - ---help--- - Show all register writes via pr_debug() - -config FB_S3C2410 - tristate "S3C2410 LCD framebuffer support" - depends on FB && ARCH_S3C24XX - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for the built-in LCD controller in the Samsung - S3C2410 processor. - - This driver is also available as a module ( = code which can be - inserted and removed from the running kernel whenever you want). The - module will be called s3c2410fb. If you want to compile it as a module, - say M here and read <file:Documentation/kbuild/modules.txt>. - - If unsure, say N. -config FB_S3C2410_DEBUG - bool "S3C2410 lcd debug messages" - depends on FB_S3C2410 - help - Turn on debugging messages. Note that you can set/unset at run time - through sysfs - -config FB_NUC900 - bool "NUC900 LCD framebuffer support" - depends on FB && ARCH_W90X900 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for the built-in LCD controller in the Nuvoton - NUC900 processor - -config GPM1040A0_320X240 - bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD" - depends on FB_NUC900 - -config FB_SM501 - tristate "Silicon Motion SM501 framebuffer support" - depends on FB && MFD_SM501 - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for the CRT and LCD controllers in the Silicon - Motion SM501. - - This driver is also available as a module ( = code which can be - inserted and removed from the running kernel whenever you want). The - module will be called sm501fb. If you want to compile it as a module, - say M here and read <file:Documentation/kbuild/modules.txt>. - - If unsure, say N. - -config FB_SMSCUFX - tristate "SMSC UFX6000/7000 USB Framebuffer support" - depends on FB && USB - select FB_MODE_HELPERS - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select FB_DEFERRED_IO - ---help--- - This is a kernel framebuffer driver for SMSC UFX USB devices. - Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and - mplayer -vo fbdev. Supports both UFX6000 (USB 2.0) and UFX7000 - (USB 3.0) devices. - To compile as a module, choose M here: the module name is smscufx. - -config FB_UDL - tristate "Displaylink USB Framebuffer support" - depends on FB && USB - select FB_MODE_HELPERS - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select FB_DEFERRED_IO - ---help--- - This is a kernel framebuffer driver for DisplayLink USB devices. - Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and - mplayer -vo fbdev. Supports all USB 2.0 era DisplayLink devices. - To compile as a module, choose M here: the module name is udlfb. - -config FB_IBM_GXT4500 - tristate "Framebuffer support for IBM GXT4000P/4500P/6000P/6500P adaptors" - depends on FB && PPC - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Say Y here to enable support for the IBM GXT4000P/6000P and - GXT4500P/6500P display adaptor based on Raster Engine RC1000, - found on some IBM System P (pSeries) machines. This driver - doesn't use Geometry Engine GT1000. - -config FB_PS3 - tristate "PS3 GPU framebuffer driver" - depends on FB && PS3_PS3AV - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE - ---help--- - Include support for the virtual frame buffer in the PS3 platform. - -config FB_PS3_DEFAULT_SIZE_M - int "PS3 default frame buffer size (in MiB)" - depends on FB_PS3 - default 9 - ---help--- - This is the default size (in MiB) of the virtual frame buffer in - the PS3. - The default value can be overridden on the kernel command line - using the "ps3fb" option (e.g. "ps3fb=9M"); - -config FB_XILINX - tristate "Xilinx frame buffer support" - depends on FB && (XILINX_VIRTEX || MICROBLAZE || ARCH_ZYNQ) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Include support for the Xilinx ML300/ML403 reference design - framebuffer. ML300 carries a 640*480 LCD display on the board, - ML403 uses a standard DB15 VGA connector. - -config FB_GOLDFISH - tristate "Goldfish Framebuffer" - depends on FB && HAS_DMA - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Framebuffer driver for Goldfish Virtual Platform - -config FB_COBALT - tristate "Cobalt server LCD frame buffer support" - depends on FB && (MIPS_COBALT || MIPS_SEAD3) - -config FB_SH7760 - bool "SH7760/SH7763/SH7720/SH7721 LCDC support" - depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \ - || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Support for the SH7760/SH7763/SH7720/SH7721 integrated - (D)STN/TFT LCD Controller. - Supports display resolutions up to 1024x1024 pixel, grayscale and - color operation, with depths ranging from 1 bpp to 8 bpp monochrome - and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for - panels <= 320 pixel horizontal resolution. - -config FB_DA8XX - tristate "DA8xx/OMAP-L1xx/AM335x Framebuffer support" - depends on FB && (ARCH_DAVINCI_DA8XX || SOC_AM33XX) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_CFB_REV_PIXELS_IN_BYTE - select FB_MODE_HELPERS - select VIDEOMODE_HELPERS - ---help--- - This is the frame buffer device driver for the TI LCD controller - found on DA8xx/OMAP-L1xx/AM335x SoCs. - If unsure, say N. - -config FB_VIRTUAL - tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)" - depends on FB - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - ---help--- - This is a `virtual' frame buffer device. It operates on a chunk of - unswappable kernel memory instead of on the memory of a graphics - board. This means you cannot see any output sent to this frame - buffer device, while it does consume precious memory. The main use - of this frame buffer device is testing and debugging the frame - buffer subsystem. Do NOT enable it for normal systems! To protect - the innocent, it has to be enabled explicitly at boot time using the - kernel option `video=vfb:'. - - To compile this driver as a module, choose M here: the - module will be called vfb. In order to load it, you must use - the vfb_enable=1 option. - - If unsure, say N. - -config XEN_FBDEV_FRONTEND - tristate "Xen virtual frame buffer support" - depends on FB && XEN - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select FB_DEFERRED_IO - select INPUT_XEN_KBDDEV_FRONTEND if INPUT_MISC - select XEN_XENBUS_FRONTEND - default y - help - This driver implements the front-end of the Xen virtual - frame buffer driver. It communicates with a back-end - in another domain. - -config FB_METRONOME - tristate "E-Ink Metronome/8track controller support" - depends on FB - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select FB_DEFERRED_IO - help - This driver implements support for the E-Ink Metronome - controller. The pre-release name for this device was 8track - and could also have been called by some vendors as PVI-nnnn. - -config FB_MB862XX - tristate "Fujitsu MB862xx GDC support" - depends on FB - depends on PCI || (OF && PPC) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers. - -choice - prompt "GDC variant" - depends on FB_MB862XX - -config FB_MB862XX_PCI_GDC - bool "Carmine/Coral-P(A) GDC" - depends on PCI - ---help--- - This enables framebuffer support for Fujitsu Carmine/Coral-P(A) - PCI graphics controller devices. - -config FB_MB862XX_LIME - bool "Lime GDC" - depends on OF && PPC - select FB_FOREIGN_ENDIAN - select FB_LITTLE_ENDIAN - ---help--- - Framebuffer support for Fujitsu Lime GDC on host CPU bus. - -endchoice - -config FB_MB862XX_I2C - bool "Support I2C bus on MB862XX GDC" - depends on FB_MB862XX && I2C - default y - help - Selecting this option adds Coral-P(A)/Lime GDC I2C bus adapter - driver to support accessing I2C devices on controller's I2C bus. - These are usually some video decoder chips. - -config FB_EP93XX - tristate "EP93XX frame buffer support" - depends on FB && ARCH_EP93XX - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - ---help--- - Framebuffer driver for the Cirrus Logic EP93XX series of processors. - This driver is also available as a module. The module will be called - ep93xx-fb. - -config FB_PRE_INIT_FB - bool "Don't reinitialize, use bootloader's GDC/Display configuration" - depends on FB && FB_MB862XX_LIME - ---help--- - Select this option if display contents should be inherited as set by - the bootloader. - -config FB_MSM - tristate "MSM Framebuffer support" - depends on FB && ARCH_MSM - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - -config FB_MX3 - tristate "MX3 Framebuffer support" - depends on FB && MX3_IPU - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - default y - help - This is a framebuffer device for the i.MX31 LCD Controller. So - far only synchronous displays are supported. If you plan to use - an LCD display with your i.MX31 system, say Y here. - -config FB_BROADSHEET - tristate "E-Ink Broadsheet/Epson S1D13521 controller support" - depends on FB - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select FB_DEFERRED_IO - help - This driver implements support for the E-Ink Broadsheet - controller. The release name for this device was Epson S1D13521 - and could also have been called by other names when coupled with - a bridge adapter. - -config FB_AUO_K190X - tristate "AUO-K190X EPD controller support" - depends on FB - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - select FB_DEFERRED_IO - help - Provides support for epaper controllers from the K190X series - of AUO. These controllers can be used to drive epaper displays - from Sipix. - - This option enables the common support, shared by the individual - controller drivers. You will also have to enable the driver - for the controller type used in your device. - -config FB_AUO_K1900 - tristate "AUO-K1900 EPD controller support" - depends on FB && FB_AUO_K190X - help - This driver implements support for the AUO K1900 epd-controller. - This controller can drive Sipix epaper displays but can only do - serial updates, reducing the number of possible frames per second. - -config FB_AUO_K1901 - tristate "AUO-K1901 EPD controller support" - depends on FB && FB_AUO_K190X - help - This driver implements support for the AUO K1901 epd-controller. - This controller can drive Sipix epaper displays and supports - concurrent updates, making higher frames per second possible. - -config FB_JZ4740 - tristate "JZ4740 LCD framebuffer support" - depends on FB && MACH_JZ4740 - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - help - Framebuffer support for the JZ4740 SoC. - -config FB_MXS - tristate "MXS LCD framebuffer support" - depends on FB && ARCH_MXS - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - select FB_MODE_HELPERS - select VIDEOMODE_HELPERS - help - Framebuffer support for the MXS SoC. - -config FB_PUV3_UNIGFX - tristate "PKUnity v3 Unigfx framebuffer support" - depends on FB && UNICORE32 && ARCH_PUV3 - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_SYS_FOPS - help - Choose this option if you want to use the Unigfx device as a - framebuffer device. Without the support of PCI & AGP. - -config FB_HYPERV - tristate "Microsoft Hyper-V Synthetic Video support" - depends on FB && HYPERV - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - This framebuffer driver supports Microsoft Hyper-V Synthetic Video. - -config FB_SIMPLE - bool "Simple framebuffer support" - depends on (FB = y) - select FB_CFB_FILLRECT - select FB_CFB_COPYAREA - select FB_CFB_IMAGEBLIT - help - Say Y if you want support for a simple frame-buffer. - - This driver assumes that the display hardware has been initialized - before the kernel boots, and the kernel will simply render to the - pre-allocated frame buffer surface. - - Configuration re: surface address, size, and format must be provided - through device tree, or plain old platform data. - -source "drivers/video/omap/Kconfig" -source "drivers/video/omap2/Kconfig" -source "drivers/video/exynos/Kconfig" -source "drivers/video/mmp/Kconfig" -source "drivers/video/backlight/Kconfig" - if VT source "drivers/video/console/Kconfig" endif if FB || SGI_NEWPORT_CONSOLE source "drivers/video/logo/Kconfig" -endif -config FB_SH_MOBILE_MERAM - tristate "SuperH Mobile MERAM read ahead support" - depends on (SUPERH || ARCH_SHMOBILE) - select GENERIC_ALLOCATOR - ---help--- - Enable MERAM support for the SuperH controller. - - This will allow for caching of the framebuffer to provide more - reliable access under heavy main memory bus traffic situations. - Up to 4 memory channels can be configured, allowing 4 RGB or - 2 YCbCr framebuffers to be configured. +endif -config FB_SSD1307 - tristate "Solomon SSD1307 framebuffer support" - depends on FB && I2C - depends on OF - depends on GPIOLIB - select FB_SYS_FOPS - select FB_SYS_FILLRECT - select FB_SYS_COPYAREA - select FB_SYS_IMAGEBLIT - select FB_DEFERRED_IO - select PWM - help - This driver implements support for the Solomon SSD1307 - OLED controller over I2C. endmenu |