diff options
Diffstat (limited to 'drivers')
111 files changed, 3938 insertions, 3070 deletions
diff --git a/drivers/bluetooth/hci_ath.c b/drivers/bluetooth/hci_ath.c index 12172a6a95c4..0bc8a6a6a148 100644 --- a/drivers/bluetooth/hci_ath.c +++ b/drivers/bluetooth/hci_ath.c @@ -58,7 +58,7 @@ static int ath_wakeup_ar3k(struct tty_struct *tty) return status; /* Disable Automatic RTSCTS */ - memcpy(&ktermios, tty->termios, sizeof(ktermios)); + ktermios = tty->termios; ktermios.c_cflag &= ~CRTSCTS; tty_set_termios(tty, &ktermios); diff --git a/drivers/char/mwave/mwavedd.c b/drivers/char/mwave/mwavedd.c index 1d82d5838f0c..164544afd680 100644 --- a/drivers/char/mwave/mwavedd.c +++ b/drivers/char/mwave/mwavedd.c @@ -430,7 +430,7 @@ static ssize_t mwave_write(struct file *file, const char __user *buf, static int register_serial_portandirq(unsigned int port, int irq) { - struct uart_port uart; + struct uart_8250_port uart; switch ( port ) { case 0x3f8: @@ -462,14 +462,14 @@ static int register_serial_portandirq(unsigned int port, int irq) } /* switch */ /* irq is okay */ - memset(&uart, 0, sizeof(struct uart_port)); + memset(&uart, 0, sizeof(uart)); - uart.uartclk = 1843200; - uart.iobase = port; - uart.irq = irq; - uart.iotype = UPIO_PORT; - uart.flags = UPF_SHARE_IRQ; - return serial8250_register_port(&uart); + uart.port.uartclk = 1843200; + uart.port.iobase = port; + uart.port.irq = irq; + uart.port.iotype = UPIO_PORT; + uart.port.flags = UPF_SHARE_IRQ; + return serial8250_register_8250_port(&uart); } diff --git a/drivers/char/pcmcia/synclink_cs.c b/drivers/char/pcmcia/synclink_cs.c index 0a484b4a1b02..5db08c78beb5 100644 --- a/drivers/char/pcmcia/synclink_cs.c +++ b/drivers/char/pcmcia/synclink_cs.c @@ -1344,7 +1344,7 @@ static void shutdown(MGSLPC_INFO * info, struct tty_struct *tty) /* TODO:disable interrupts instead of reset to preserve signal states */ reset_device(info); - if (!tty || tty->termios->c_cflag & HUPCL) { + if (!tty || tty->termios.c_cflag & HUPCL) { info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS); set_signals(info); } @@ -1385,7 +1385,7 @@ static void mgslpc_program_hw(MGSLPC_INFO *info, struct tty_struct *tty) port_irq_enable(info, (unsigned char) PVR_DSR | PVR_RI); get_signals(info); - if (info->netcount || (tty && (tty->termios->c_cflag & CREAD))) + if (info->netcount || (tty && (tty->termios.c_cflag & CREAD))) rx_start(info); spin_unlock_irqrestore(&info->lock,flags); @@ -1398,14 +1398,14 @@ static void mgslpc_change_params(MGSLPC_INFO *info, struct tty_struct *tty) unsigned cflag; int bits_per_char; - if (!tty || !tty->termios) + if (!tty) return; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgslpc_change_params(%s)\n", __FILE__,__LINE__, info->device_name ); - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; /* if B0 rate (hangup) specified then negate DTR and RTS */ /* otherwise assert DTR and RTS */ @@ -1728,7 +1728,7 @@ static void mgslpc_throttle(struct tty_struct * tty) if (I_IXOFF(tty)) mgslpc_send_xchar(tty, STOP_CHAR(tty)); - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { spin_lock_irqsave(&info->lock,flags); info->serial_signals &= ~SerialSignal_RTS; set_signals(info); @@ -1757,7 +1757,7 @@ static void mgslpc_unthrottle(struct tty_struct * tty) mgslpc_send_xchar(tty, START_CHAR(tty)); } - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { spin_lock_irqsave(&info->lock,flags); info->serial_signals |= SerialSignal_RTS; set_signals(info); @@ -2293,8 +2293,8 @@ static void mgslpc_set_termios(struct tty_struct *tty, struct ktermios *old_term tty->driver->name ); /* just return if nothing has changed */ - if ((tty->termios->c_cflag == old_termios->c_cflag) - && (RELEVANT_IFLAG(tty->termios->c_iflag) + if ((tty->termios.c_cflag == old_termios->c_cflag) + && (RELEVANT_IFLAG(tty->termios.c_iflag) == RELEVANT_IFLAG(old_termios->c_iflag))) return; @@ -2302,7 +2302,7 @@ static void mgslpc_set_termios(struct tty_struct *tty, struct ktermios *old_term /* Handle transition to B0 status */ if (old_termios->c_cflag & CBAUD && - !(tty->termios->c_cflag & CBAUD)) { + !(tty->termios.c_cflag & CBAUD)) { info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR); spin_lock_irqsave(&info->lock,flags); set_signals(info); @@ -2311,9 +2311,9 @@ static void mgslpc_set_termios(struct tty_struct *tty, struct ktermios *old_term /* Handle transition away from B0 status */ if (!(old_termios->c_cflag & CBAUD) && - tty->termios->c_cflag & CBAUD) { + tty->termios.c_cflag & CBAUD) { info->serial_signals |= SerialSignal_DTR; - if (!(tty->termios->c_cflag & CRTSCTS) || + if (!(tty->termios.c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags)) { info->serial_signals |= SerialSignal_RTS; } @@ -2324,7 +2324,7 @@ static void mgslpc_set_termios(struct tty_struct *tty, struct ktermios *old_term /* Handle turning off CRTSCTS */ if (old_termios->c_cflag & CRTSCTS && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; tx_release(tty); } @@ -2731,6 +2731,8 @@ static void mgslpc_add_device(MGSLPC_INFO *info) #if SYNCLINK_GENERIC_HDLC hdlcdev_init(info); #endif + tty_port_register_device(&info->port, serial_driver, info->line, + &info->p_dev->dev); } static void mgslpc_remove_device(MGSLPC_INFO *remove_info) @@ -2744,6 +2746,7 @@ static void mgslpc_remove_device(MGSLPC_INFO *remove_info) last->next_device = info->next_device; else mgslpc_device_list = info->next_device; + tty_unregister_device(serial_driver, info->line); #if SYNCLINK_GENERIC_HDLC hdlcdev_exit(info); #endif @@ -2798,77 +2801,63 @@ static const struct tty_operations mgslpc_ops = { .proc_fops = &mgslpc_proc_fops, }; -static void synclink_cs_cleanup(void) +static int __init synclink_cs_init(void) { int rc; - while(mgslpc_device_list) - mgslpc_remove_device(mgslpc_device_list); - - if (serial_driver) { - if ((rc = tty_unregister_driver(serial_driver))) - printk("%s(%d) failed to unregister tty driver err=%d\n", - __FILE__,__LINE__,rc); - put_tty_driver(serial_driver); + if (break_on_load) { + mgslpc_get_text_ptr(); + BREAKPOINT(); } - pcmcia_unregister_driver(&mgslpc_driver); -} - -static int __init synclink_cs_init(void) -{ - int rc; - - if (break_on_load) { - mgslpc_get_text_ptr(); - BREAKPOINT(); - } - - if ((rc = pcmcia_register_driver(&mgslpc_driver)) < 0) - return rc; - - serial_driver = alloc_tty_driver(MAX_DEVICE_COUNT); - if (!serial_driver) { - rc = -ENOMEM; - goto error; - } + serial_driver = tty_alloc_driver(MAX_DEVICE_COUNT, + TTY_DRIVER_REAL_RAW | + TTY_DRIVER_DYNAMIC_DEV); + if (IS_ERR(serial_driver)) { + rc = PTR_ERR(serial_driver); + goto err; + } - /* Initialize the tty_driver structure */ - - serial_driver->driver_name = "synclink_cs"; - serial_driver->name = "ttySLP"; - serial_driver->major = ttymajor; - serial_driver->minor_start = 64; - serial_driver->type = TTY_DRIVER_TYPE_SERIAL; - serial_driver->subtype = SERIAL_TYPE_NORMAL; - serial_driver->init_termios = tty_std_termios; - serial_driver->init_termios.c_cflag = - B9600 | CS8 | CREAD | HUPCL | CLOCAL; - serial_driver->flags = TTY_DRIVER_REAL_RAW; - tty_set_operations(serial_driver, &mgslpc_ops); - - if ((rc = tty_register_driver(serial_driver)) < 0) { - printk("%s(%d):Couldn't register serial driver\n", - __FILE__,__LINE__); - put_tty_driver(serial_driver); - serial_driver = NULL; - goto error; - } + /* Initialize the tty_driver structure */ + serial_driver->driver_name = "synclink_cs"; + serial_driver->name = "ttySLP"; + serial_driver->major = ttymajor; + serial_driver->minor_start = 64; + serial_driver->type = TTY_DRIVER_TYPE_SERIAL; + serial_driver->subtype = SERIAL_TYPE_NORMAL; + serial_driver->init_termios = tty_std_termios; + serial_driver->init_termios.c_cflag = + B9600 | CS8 | CREAD | HUPCL | CLOCAL; + tty_set_operations(serial_driver, &mgslpc_ops); + + rc = tty_register_driver(serial_driver); + if (rc < 0) { + printk(KERN_ERR "%s(%d):Couldn't register serial driver\n", + __FILE__, __LINE__); + goto err_put_tty; + } - printk("%s %s, tty major#%d\n", - driver_name, driver_version, - serial_driver->major); + rc = pcmcia_register_driver(&mgslpc_driver); + if (rc < 0) + goto err_unreg_tty; - return 0; + printk(KERN_INFO "%s %s, tty major#%d\n", driver_name, driver_version, + serial_driver->major); -error: - synclink_cs_cleanup(); - return rc; + return 0; +err_unreg_tty: + tty_unregister_driver(serial_driver); +err_put_tty: + put_tty_driver(serial_driver); +err: + return rc; } static void __exit synclink_cs_exit(void) { - synclink_cs_cleanup(); + pcmcia_unregister_driver(&mgslpc_driver); + tty_unregister_driver(serial_driver); + put_tty_driver(serial_driver); } module_init(synclink_cs_init); diff --git a/drivers/char/ttyprintk.c b/drivers/char/ttyprintk.c index 46b77ede84c0..af98f6d6509b 100644 --- a/drivers/char/ttyprintk.c +++ b/drivers/char/ttyprintk.c @@ -67,7 +67,7 @@ static int tpk_printk(const unsigned char *buf, int count) tmp[tpk_curr + 1] = '\0'; printk(KERN_INFO "%s%s", tpk_tag, tmp); tpk_curr = 0; - if (buf[i + 1] == '\n') + if ((i + 1) < count && buf[i + 1] == '\n') i++; break; case '\n': @@ -178,11 +178,17 @@ static struct tty_driver *ttyprintk_driver; static int __init ttyprintk_init(void) { int ret = -ENOMEM; - void *rp; - ttyprintk_driver = alloc_tty_driver(1); - if (!ttyprintk_driver) - return ret; + tty_port_init(&tpk_port.port); + tpk_port.port.ops = &null_ops; + mutex_init(&tpk_port.port_write_mutex); + + ttyprintk_driver = tty_alloc_driver(1, + TTY_DRIVER_RESET_TERMIOS | + TTY_DRIVER_REAL_RAW | + TTY_DRIVER_UNNUMBERED_NODE); + if (IS_ERR(ttyprintk_driver)) + return PTR_ERR(ttyprintk_driver); ttyprintk_driver->driver_name = "ttyprintk"; ttyprintk_driver->name = "ttyprintk"; @@ -191,9 +197,8 @@ static int __init ttyprintk_init(void) ttyprintk_driver->type = TTY_DRIVER_TYPE_CONSOLE; ttyprintk_driver->init_termios = tty_std_termios; ttyprintk_driver->init_termios.c_oflag = OPOST | OCRNL | ONOCR | ONLRET; - ttyprintk_driver->flags = TTY_DRIVER_RESET_TERMIOS | - TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; tty_set_operations(ttyprintk_driver, &ttyprintk_ops); + tty_port_link_device(&tpk_port.port, ttyprintk_driver, 0); ret = tty_register_driver(ttyprintk_driver); if (ret < 0) { @@ -201,22 +206,10 @@ static int __init ttyprintk_init(void) goto error; } - /* create our unnumbered device */ - rp = device_create(tty_class, NULL, MKDEV(TTYAUX_MAJOR, 3), NULL, - ttyprintk_driver->name); - if (IS_ERR(rp)) { - printk(KERN_ERR "Couldn't create ttyprintk device\n"); - ret = PTR_ERR(rp); - goto error; - } - - tty_port_init(&tpk_port.port); - tpk_port.port.ops = &null_ops; - mutex_init(&tpk_port.port_write_mutex); - return 0; error: + tty_unregister_driver(ttyprintk_driver); put_tty_driver(ttyprintk_driver); ttyprintk_driver = NULL; return ret; diff --git a/drivers/isdn/capi/capi.c b/drivers/isdn/capi/capi.c index 38c4bd87b2c9..c679867c2ccd 100644 --- a/drivers/isdn/capi/capi.c +++ b/drivers/isdn/capi/capi.c @@ -234,7 +234,8 @@ static struct capiminor *capiminor_alloc(struct capi20_appl *ap, u32 ncci) mp->minor = minor; - dev = tty_register_device(capinc_tty_driver, minor, NULL); + dev = tty_port_register_device(&mp->port, capinc_tty_driver, minor, + NULL); if (IS_ERR(dev)) goto err_out2; diff --git a/drivers/isdn/gigaset/interface.c b/drivers/isdn/gigaset/interface.c index a6d9fd2858f7..67abf3ff45e8 100644 --- a/drivers/isdn/gigaset/interface.c +++ b/drivers/isdn/gigaset/interface.c @@ -446,8 +446,8 @@ static void if_set_termios(struct tty_struct *tty, struct ktermios *old) goto out; } - iflag = tty->termios->c_iflag; - cflag = tty->termios->c_cflag; + iflag = tty->termios.c_iflag; + cflag = tty->termios.c_cflag; old_cflag = old ? old->c_cflag : cflag; gig_dbg(DEBUG_IF, "%u: iflag %x cflag %x old %x", cs->minor_index, iflag, cflag, old_cflag); @@ -524,7 +524,8 @@ void gigaset_if_init(struct cardstate *cs) tasklet_init(&cs->if_wake_tasklet, if_wake, (unsigned long) cs); mutex_lock(&cs->mutex); - cs->tty_dev = tty_register_device(drv->tty, cs->minor_index, NULL); + cs->tty_dev = tty_port_register_device(&cs->port, drv->tty, + cs->minor_index, NULL); if (!IS_ERR(cs->tty_dev)) dev_set_drvdata(cs->tty_dev, cs); diff --git a/drivers/isdn/i4l/isdn_tty.c b/drivers/isdn/i4l/isdn_tty.c index 7bc50670d7d9..b817809f763c 100644 --- a/drivers/isdn/i4l/isdn_tty.c +++ b/drivers/isdn/i4l/isdn_tty.c @@ -1009,15 +1009,15 @@ isdn_tty_change_speed(modem_info *info) quot; int i; - if (!port->tty || !port->tty->termios) + if (!port->tty) return; - cflag = port->tty->termios->c_cflag; + cflag = port->tty->termios.c_cflag; quot = i = cflag & CBAUD; if (i & CBAUDEX) { i &= ~CBAUDEX; if (i < 1 || i > 2) - port->tty->termios->c_cflag &= ~CBAUDEX; + port->tty->termios.c_cflag &= ~CBAUDEX; else i += 15; } @@ -1097,7 +1097,7 @@ isdn_tty_shutdown(modem_info *info) #endif isdn_unlock_drivers(); info->msr &= ~UART_MSR_RI; - if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) { + if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) { info->mcr &= ~(UART_MCR_DTR | UART_MCR_RTS); if (info->emu.mdmreg[REG_DTRHUP] & BIT_DTRHUP) { isdn_tty_modem_reset_regs(info, 0); @@ -1469,13 +1469,13 @@ isdn_tty_set_termios(struct tty_struct *tty, struct ktermios *old_termios) if (!old_termios) isdn_tty_change_speed(info); else { - if (tty->termios->c_cflag == old_termios->c_cflag && - tty->termios->c_ispeed == old_termios->c_ispeed && - tty->termios->c_ospeed == old_termios->c_ospeed) + if (tty->termios.c_cflag == old_termios->c_cflag && + tty->termios.c_ispeed == old_termios->c_ispeed && + tty->termios.c_ospeed == old_termios->c_ospeed) return; isdn_tty_change_speed(info); if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) + !(tty->termios.c_cflag & CRTSCTS)) tty->hw_stopped = 0; } } @@ -1486,6 +1486,18 @@ isdn_tty_set_termios(struct tty_struct *tty, struct ktermios *old_termios) * ------------------------------------------------------------ */ +static int isdn_tty_install(struct tty_driver *driver, struct tty_struct *tty) +{ + modem_info *info = &dev->mdm.info[tty->index]; + + if (isdn_tty_paranoia_check(info, tty->name, __func__)) + return -ENODEV; + + tty->driver_data = info; + + return tty_port_install(&info->port, driver, tty); +} + /* * This routine is called whenever a serial port is opened. It * enables interrupts for a serial port, linking in its async structure into @@ -1495,22 +1507,16 @@ isdn_tty_set_termios(struct tty_struct *tty, struct ktermios *old_termios) static int isdn_tty_open(struct tty_struct *tty, struct file *filp) { - struct tty_port *port; - modem_info *info; + modem_info *info = tty->driver_data; + struct tty_port *port = &info->port; int retval; - info = &dev->mdm.info[tty->index]; - if (isdn_tty_paranoia_check(info, tty->name, "isdn_tty_open")) - return -ENODEV; - port = &info->port; #ifdef ISDN_DEBUG_MODEM_OPEN printk(KERN_DEBUG "isdn_tty_open %s, count = %d\n", tty->name, port->count); #endif port->count++; - tty->driver_data = info; port->tty = tty; - tty->port = port; /* * Start up serial port */ @@ -1738,6 +1744,7 @@ modem_write_profile(atemu *m) } static const struct tty_operations modem_ops = { + .install = isdn_tty_install, .open = isdn_tty_open, .close = isdn_tty_close, .write = isdn_tty_write, @@ -1782,7 +1789,7 @@ isdn_tty_modem_init(void) m->tty_modem->subtype = SERIAL_TYPE_NORMAL; m->tty_modem->init_termios = tty_std_termios; m->tty_modem->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL; - m->tty_modem->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; + m->tty_modem->flags = TTY_DRIVER_REAL_RAW; m->tty_modem->driver_name = "isdn_tty"; tty_set_operations(m->tty_modem, &modem_ops); retval = tty_register_driver(m->tty_modem); diff --git a/drivers/misc/ibmasm/uart.c b/drivers/misc/ibmasm/uart.c index 1dcb9ae1905a..01e2b0d7e590 100644 --- a/drivers/misc/ibmasm/uart.c +++ b/drivers/misc/ibmasm/uart.c @@ -33,7 +33,7 @@ void ibmasm_register_uart(struct service_processor *sp) { - struct uart_port uport; + struct uart_8250_port uart; void __iomem *iomem_base; iomem_base = sp->base_address + SCOUT_COM_B_BASE; @@ -47,14 +47,14 @@ void ibmasm_register_uart(struct service_processor *sp) return; } - memset(&uport, 0, sizeof(struct uart_port)); - uport.irq = sp->irq; - uport.uartclk = 3686400; - uport.flags = UPF_SHARE_IRQ; - uport.iotype = UPIO_MEM; - uport.membase = iomem_base; + memset(&uart, 0, sizeof(uart)); + uart.port.irq = sp->irq; + uart.port.uartclk = 3686400; + uart.port.flags = UPF_SHARE_IRQ; + uart.port.iotype = UPIO_MEM; + uart.port.membase = iomem_base; - sp->serial_line = serial8250_register_port(&uport); + sp->serial_line = serial8250_register_8250_port(&uart); if (sp->serial_line < 0) { dev_err(sp->dev, "Failed to register serial port\n"); return; diff --git a/drivers/misc/pti.c b/drivers/misc/pti.c index b7eb545394b1..4999b34b7a60 100644 --- a/drivers/misc/pti.c +++ b/drivers/misc/pti.c @@ -60,7 +60,7 @@ struct pti_tty { }; struct pti_dev { - struct tty_port port; + struct tty_port port[PTITTY_MINOR_NUM]; unsigned long pti_addr; unsigned long aperture_base; void __iomem *pti_ioaddr; @@ -76,7 +76,7 @@ struct pti_dev { */ static DEFINE_MUTEX(alloclock); -static struct pci_device_id pci_ids[] __devinitconst = { +static const struct pci_device_id pci_ids[] __devinitconst = { {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x82B)}, {0} }; @@ -393,25 +393,6 @@ void pti_writedata(struct pti_masterchannel *mc, u8 *buf, int count) } EXPORT_SYMBOL_GPL(pti_writedata); -/** - * pti_pci_remove()- Driver exit method to remove PTI from - * PCI bus. - * @pdev: variable containing pci info of PTI. - */ -static void __devexit pti_pci_remove(struct pci_dev *pdev) -{ - struct pti_dev *drv_data; - - drv_data = pci_get_drvdata(pdev); - if (drv_data != NULL) { - pci_iounmap(pdev, drv_data->pti_ioaddr); - pci_set_drvdata(pdev, NULL); - kfree(drv_data); - pci_release_region(pdev, 1); - pci_disable_device(pdev); - } -} - /* * for the tty_driver_*() basic function descriptions, see tty_driver.h. * Specific header comments made for PTI-related specifics. @@ -446,7 +427,7 @@ static int pti_tty_driver_open(struct tty_struct *tty, struct file *filp) * also removes a locking requirement for the actual write * procedure. */ - return tty_port_open(&drv_data->port, tty, filp); + return tty_port_open(tty->port, tty, filp); } /** @@ -462,7 +443,7 @@ static int pti_tty_driver_open(struct tty_struct *tty, struct file *filp) */ static void pti_tty_driver_close(struct tty_struct *tty, struct file *filp) { - tty_port_close(&drv_data->port, tty, filp); + tty_port_close(tty->port, tty, filp); } /** @@ -818,6 +799,7 @@ static const struct tty_port_operations tty_port_ops = { static int __devinit pti_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { + unsigned int a; int retval = -EINVAL; int pci_bar = 1; @@ -830,7 +812,7 @@ static int __devinit pti_pci_probe(struct pci_dev *pdev, __func__, __LINE__); pr_err("%s(%d): Error value returned: %d\n", __func__, __LINE__, retval); - return retval; + goto err; } retval = pci_enable_device(pdev); @@ -838,17 +820,16 @@ static int __devinit pti_pci_probe(struct pci_dev *pdev, dev_err(&pdev->dev, "%s: pci_enable_device() returned error %d\n", __func__, retval); - return retval; + goto err_unreg_misc; } drv_data = kzalloc(sizeof(*drv_data), GFP_KERNEL); - if (drv_data == NULL) { retval = -ENOMEM; dev_err(&pdev->dev, "%s(%d): kmalloc() returned NULL memory.\n", __func__, __LINE__); - return retval; + goto err_disable_pci; } drv_data->pti_addr = pci_resource_start(pdev, pci_bar); @@ -857,33 +838,65 @@ static int __devinit pti_pci_probe(struct pci_dev *pdev, dev_err(&pdev->dev, "%s(%d): pci_request_region() returned error %d\n", __func__, __LINE__, retval); - kfree(drv_data); - return retval; + goto err_free_dd; } drv_data->aperture_base = drv_data->pti_addr+APERTURE_14; drv_data->pti_ioaddr = ioremap_nocache((u32)drv_data->aperture_base, APERTURE_LEN); if (!drv_data->pti_ioaddr) { - pci_release_region(pdev, pci_bar); retval = -ENOMEM; - kfree(drv_data); - return retval; + goto err_rel_reg; } pci_set_drvdata(pdev, drv_data); - tty_port_init(&drv_data->port); - drv_data->port.ops = &tty_port_ops; + for (a = 0; a < PTITTY_MINOR_NUM; a++) { + struct tty_port *port = &drv_data->port[a]; + tty_port_init(port); + port->ops = &tty_port_ops; - tty_register_device(pti_tty_driver, 0, &pdev->dev); - tty_register_device(pti_tty_driver, 1, &pdev->dev); + tty_port_register_device(port, pti_tty_driver, a, &pdev->dev); + } register_console(&pti_console); + return 0; +err_rel_reg: + pci_release_region(pdev, pci_bar); +err_free_dd: + kfree(drv_data); +err_disable_pci: + pci_disable_device(pdev); +err_unreg_misc: + misc_deregister(&pti_char_driver); +err: return retval; } +/** + * pti_pci_remove()- Driver exit method to remove PTI from + * PCI bus. + * @pdev: variable containing pci info of PTI. + */ +static void __devexit pti_pci_remove(struct pci_dev *pdev) +{ + struct pti_dev *drv_data = pci_get_drvdata(pdev); + + unregister_console(&pti_console); + + tty_unregister_device(pti_tty_driver, 0); + tty_unregister_device(pti_tty_driver, 1); + + iounmap(drv_data->pti_ioaddr); + pci_set_drvdata(pdev, NULL); + kfree(drv_data); + pci_release_region(pdev, 1); + pci_disable_device(pdev); + + misc_deregister(&pti_char_driver); +} + static struct pci_driver pti_pci_driver = { .name = PCINAME, .id_table = pci_ids, @@ -933,25 +946,24 @@ static int __init pti_init(void) pr_err("%s(%d): Error value returned: %d\n", __func__, __LINE__, retval); - pti_tty_driver = NULL; - return retval; + goto put_tty; } retval = pci_register_driver(&pti_pci_driver); - if (retval) { pr_err("%s(%d): PCI registration failed of pti driver\n", __func__, __LINE__); pr_err("%s(%d): Error value returned: %d\n", __func__, __LINE__, retval); - - tty_unregister_driver(pti_tty_driver); - pr_err("%s(%d): Unregistering TTY part of pti driver\n", - __func__, __LINE__); - pti_tty_driver = NULL; - return retval; + goto unreg_tty; } + return 0; +unreg_tty: + tty_unregister_driver(pti_tty_driver); +put_tty: + put_tty_driver(pti_tty_driver); + pti_tty_driver = NULL; return retval; } @@ -960,31 +972,9 @@ static int __init pti_init(void) */ static void __exit pti_exit(void) { - int retval; - - tty_unregister_device(pti_tty_driver, 0); - tty_unregister_device(pti_tty_driver, 1); - - retval = tty_unregister_driver(pti_tty_driver); - if (retval) { - pr_err("%s(%d): TTY unregistration failed of pti driver\n", - __func__, __LINE__); - pr_err("%s(%d): Error value returned: %d\n", - __func__, __LINE__, retval); - } - + tty_unregister_driver(pti_tty_driver); pci_unregister_driver(&pti_pci_driver); - - retval = misc_deregister(&pti_char_driver); - if (retval) { - pr_err("%s(%d): CHAR unregistration failed of pti driver\n", - __func__, __LINE__); - pr_err("%s(%d): Error value returned: %d\n", - __func__, __LINE__, retval); - } - - unregister_console(&pti_console); - return; + put_tty_driver(pti_tty_driver); } module_init(pti_init); diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c index 5a2cbfac66d2..d2339ea37815 100644 --- a/drivers/mmc/card/sdio_uart.c +++ b/drivers/mmc/card/sdio_uart.c @@ -518,7 +518,7 @@ static void sdio_uart_check_modem_status(struct sdio_uart_port *port) if (status & UART_MSR_DCTS) { port->icount.cts++; tty = tty_port_tty_get(&port->port); - if (tty && (tty->termios->c_cflag & CRTSCTS)) { + if (tty && (tty->termios.c_cflag & CRTSCTS)) { int cts = (status & UART_MSR_CTS); if (tty->hw_stopped) { if (cts) { @@ -671,12 +671,12 @@ static int sdio_uart_activate(struct tty_port *tport, struct tty_struct *tty) port->ier = UART_IER_RLSI|UART_IER_RDI|UART_IER_RTOIE|UART_IER_UUE; port->mctrl = TIOCM_OUT2; - sdio_uart_change_speed(port, tty->termios, NULL); + sdio_uart_change_speed(port, &tty->termios, NULL); - if (tty->termios->c_cflag & CBAUD) + if (tty->termios.c_cflag & CBAUD) sdio_uart_set_mctrl(port, TIOCM_RTS | TIOCM_DTR); - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) if (!(sdio_uart_get_mctrl(port) & TIOCM_CTS)) tty->hw_stopped = 1; @@ -850,7 +850,7 @@ static void sdio_uart_throttle(struct tty_struct *tty) { struct sdio_uart_port *port = tty->driver_data; - if (!I_IXOFF(tty) && !(tty->termios->c_cflag & CRTSCTS)) + if (!I_IXOFF(tty) && !(tty->termios.c_cflag & CRTSCTS)) return; if (sdio_uart_claim_func(port) != 0) @@ -861,7 +861,7 @@ static void sdio_uart_throttle(struct tty_struct *tty) sdio_uart_start_tx(port); } - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) sdio_uart_clear_mctrl(port, TIOCM_RTS); sdio_uart_irq(port->func); @@ -872,7 +872,7 @@ static void sdio_uart_unthrottle(struct tty_struct *tty) { struct sdio_uart_port *port = tty->driver_data; - if (!I_IXOFF(tty) && !(tty->termios->c_cflag & CRTSCTS)) + if (!I_IXOFF(tty) && !(tty->termios.c_cflag & CRTSCTS)) return; if (sdio_uart_claim_func(port) != 0) @@ -887,7 +887,7 @@ static void sdio_uart_unthrottle(struct tty_struct *tty) } } - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) sdio_uart_set_mctrl(port, TIOCM_RTS); sdio_uart_irq(port->func); @@ -898,12 +898,12 @@ static void sdio_uart_set_termios(struct tty_struct *tty, struct ktermios *old_termios) { struct sdio_uart_port *port = tty->driver_data; - unsigned int cflag = tty->termios->c_cflag; + unsigned int cflag = tty->termios.c_cflag; if (sdio_uart_claim_func(port) != 0) return; - sdio_uart_change_speed(port, tty->termios, old_termios); + sdio_uart_change_speed(port, &tty->termios, old_termios); /* Handle transition to B0 status */ if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD)) @@ -1132,8 +1132,8 @@ static int sdio_uart_probe(struct sdio_func *func, kfree(port); } else { struct device *dev; - dev = tty_register_device(sdio_uart_tty_driver, - port->index, &func->dev); + dev = tty_port_register_device(&port->port, + sdio_uart_tty_driver, port->index, &func->dev); if (IS_ERR(dev)) { sdio_uart_port_remove(port); ret = PTR_ERR(dev); diff --git a/drivers/net/ethernet/sgi/ioc3-eth.c b/drivers/net/ethernet/sgi/ioc3-eth.c index b5ba3084c7fc..3e5519a0acc7 100644 --- a/drivers/net/ethernet/sgi/ioc3-eth.c +++ b/drivers/net/ethernet/sgi/ioc3-eth.c @@ -1147,15 +1147,17 @@ static void __devinit ioc3_8250_register(struct ioc3_uartregs __iomem *uart) { #define COSMISC_CONSTANT 6 - struct uart_port port = { - .irq = 0, - .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, - .iotype = UPIO_MEM, - .regshift = 0, - .uartclk = (22000000 << 1) / COSMISC_CONSTANT, - - .membase = (unsigned char __iomem *) uart, - .mapbase = (unsigned long) uart, + struct uart_8250_port port = { + .port = { + .irq = 0, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 0, + .uartclk = (22000000 << 1) / COSMISC_CONSTANT, + + .membase = (unsigned char __iomem *) uart, + .mapbase = (unsigned long) uart, + } }; unsigned char lcr; @@ -1164,7 +1166,7 @@ static void __devinit ioc3_8250_register(struct ioc3_uartregs __iomem *uart) uart->iu_scr = COSMISC_CONSTANT, uart->iu_lcr = lcr; uart->iu_lcr; - serial8250_register_port(&port); + serial8250_register_8250_port(&port); } static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3) diff --git a/drivers/net/irda/irtty-sir.c b/drivers/net/irda/irtty-sir.c index 3352b2443e58..30087ca23a0f 100644 --- a/drivers/net/irda/irtty-sir.c +++ b/drivers/net/irda/irtty-sir.c @@ -124,8 +124,8 @@ static int irtty_change_speed(struct sir_dev *dev, unsigned speed) tty = priv->tty; mutex_lock(&tty->termios_mutex); - old_termios = *(tty->termios); - cflag = tty->termios->c_cflag; + old_termios = tty->termios; + cflag = tty->termios.c_cflag; tty_encode_baud_rate(tty, speed, speed); if (tty->ops->set_termios) tty->ops->set_termios(tty, &old_termios); @@ -281,15 +281,15 @@ static inline void irtty_stop_receiver(struct tty_struct *tty, int stop) int cflag; mutex_lock(&tty->termios_mutex); - old_termios = *(tty->termios); - cflag = tty->termios->c_cflag; + old_termios = tty->termios; + cflag = tty->termios.c_cflag; if (stop) cflag &= ~CREAD; else cflag |= CREAD; - tty->termios->c_cflag = cflag; + tty->termios.c_cflag = cflag; if (tty->ops->set_termios) tty->ops->set_termios(tty, &old_termios); mutex_unlock(&tty->termios_mutex); diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c index 62f30b46fa42..605a4baa9b7b 100644 --- a/drivers/net/usb/hso.c +++ b/drivers/net/usb/hso.c @@ -1107,7 +1107,6 @@ static void _hso_serial_set_termios(struct tty_struct *tty, struct ktermios *old) { struct hso_serial *serial = tty->driver_data; - struct ktermios *termios; if (!serial) { printk(KERN_ERR "%s: no tty structures", __func__); @@ -1119,16 +1118,15 @@ static void _hso_serial_set_termios(struct tty_struct *tty, /* * Fix up unsupported bits */ - termios = tty->termios; - termios->c_iflag &= ~IXON; /* disable enable XON/XOFF flow control */ + tty->termios.c_iflag &= ~IXON; /* disable enable XON/XOFF flow control */ - termios->c_cflag &= + tty->termios.c_cflag &= ~(CSIZE /* no size */ | PARENB /* disable parity bit */ | CBAUD /* clear current baud rate */ | CBAUDEX); /* clear current buad rate */ - termios->c_cflag |= CS8; /* character size 8 bits */ + tty->termios.c_cflag |= CS8; /* character size 8 bits */ /* baud rate 115200 */ tty_encode_baud_rate(tty, 115200, 115200); @@ -1425,14 +1423,14 @@ static void hso_serial_set_termios(struct tty_struct *tty, struct ktermios *old) if (old) D5("Termios called with: cflags new[%d] - old[%d]", - tty->termios->c_cflag, old->c_cflag); + tty->termios.c_cflag, old->c_cflag); /* the actual setup */ spin_lock_irqsave(&serial->serial_lock, flags); if (serial->port.count) _hso_serial_set_termios(tty, old); else - tty->termios = old; + tty->termios = *old; spin_unlock_irqrestore(&serial->serial_lock, flags); /* done */ @@ -2289,9 +2287,11 @@ static int hso_serial_common_create(struct hso_serial *serial, int num_urbs, if (minor < 0) goto exit; + tty_port_init(&serial->port); + /* register our minor number */ - serial->parent->dev = tty_register_device(tty_drv, minor, - &serial->parent->interface->dev); + serial->parent->dev = tty_port_register_device(&serial->port, tty_drv, + minor, &serial->parent->interface->dev); dev = serial->parent->dev; dev_set_drvdata(dev, serial->parent); i = device_create_file(dev, &dev_attr_hsotype); @@ -2300,7 +2300,6 @@ static int hso_serial_common_create(struct hso_serial *serial, int num_urbs, serial->minor = minor; serial->magic = HSO_SERIAL_MAGIC; spin_lock_init(&serial->serial_lock); - tty_port_init(&serial->port); serial->num_rx_urbs = num_urbs; /* RX, allocate urb and initialize */ diff --git a/drivers/s390/char/con3215.c b/drivers/s390/char/con3215.c index 6c0116d48c74..9ffb6d5f17aa 100644 --- a/drivers/s390/char/con3215.c +++ b/drivers/s390/char/con3215.c @@ -716,10 +716,17 @@ static int raw3215_probe (struct ccw_device *cdev) static void raw3215_remove (struct ccw_device *cdev) { struct raw3215_info *raw; + unsigned int line; ccw_device_set_offline(cdev); raw = dev_get_drvdata(&cdev->dev); if (raw) { + spin_lock(&raw3215_device_lock); + for (line = 0; line < NR_3215; line++) + if (raw3215[line] == raw) + break; + raw3215[line] = NULL; + spin_unlock(&raw3215_device_lock); dev_set_drvdata(&cdev->dev, NULL); raw3215_free_info(raw); } @@ -935,6 +942,19 @@ static int __init con3215_init(void) console_initcall(con3215_init); #endif +static int tty3215_install(struct tty_driver *driver, struct tty_struct *tty) +{ + struct raw3215_info *raw; + + raw = raw3215[tty->index]; + if (raw == NULL) + return -ENODEV; + + tty->driver_data = raw; + + return tty_port_install(&raw->port, driver, tty); +} + /* * tty3215_open * @@ -942,14 +962,9 @@ console_initcall(con3215_init); */ static int tty3215_open(struct tty_struct *tty, struct file * filp) { - struct raw3215_info *raw; + struct raw3215_info *raw = tty->driver_data; int retval; - raw = raw3215[tty->index]; - if (raw == NULL) - return -ENODEV; - - tty->driver_data = raw; tty_port_tty_set(&raw->port, tty); tty->low_latency = 0; /* don't use bottom half for pushing chars */ @@ -1110,6 +1125,7 @@ static void tty3215_start(struct tty_struct *tty) } static const struct tty_operations tty3215_ops = { + .install = tty3215_install, .open = tty3215_open, .close = tty3215_close, .write = tty3215_write, diff --git a/drivers/s390/char/sclp_tty.c b/drivers/s390/char/sclp_tty.c index 0792c85baafe..30ec09e3d037 100644 --- a/drivers/s390/char/sclp_tty.c +++ b/drivers/s390/char/sclp_tty.c @@ -567,6 +567,7 @@ sclp_tty_init(void) driver->init_termios.c_lflag = ISIG | ECHO; driver->flags = TTY_DRIVER_REAL_RAW; tty_set_operations(driver, &sclp_ops); + tty_port_link_device(&sclp_port, driver, 0); rc = tty_register_driver(driver); if (rc) { put_tty_driver(driver); diff --git a/drivers/s390/char/sclp_vt220.c b/drivers/s390/char/sclp_vt220.c index edfc0fd73dc6..7e60f3d2f3f9 100644 --- a/drivers/s390/char/sclp_vt220.c +++ b/drivers/s390/char/sclp_vt220.c @@ -691,6 +691,7 @@ static int __init sclp_vt220_tty_init(void) driver->init_termios = tty_std_termios; driver->flags = TTY_DRIVER_REAL_RAW; tty_set_operations(driver, &sclp_vt220_ops); + tty_port_link_device(&sclp_vt220_port, driver, 0); rc = tty_register_driver(driver); if (rc) diff --git a/drivers/s390/char/tty3270.c b/drivers/s390/char/tty3270.c index 1928f3458d10..482ee028f842 100644 --- a/drivers/s390/char/tty3270.c +++ b/drivers/s390/char/tty3270.c @@ -842,17 +842,14 @@ static struct raw3270_fn tty3270_fn = { }; /* - * This routine is called whenever a 3270 tty is opened. + * This routine is called whenever a 3270 tty is opened first time. */ -static int -tty3270_open(struct tty_struct *tty, struct file * filp) +static int tty3270_install(struct tty_driver *driver, struct tty_struct *tty) { struct raw3270_view *view; struct tty3270 *tp; int i, rc; - if (tty->count > 1) - return 0; /* Check if the tty3270 is already there. */ view = raw3270_find_view(&tty3270_fn, tty->index + RAW3270_FIRSTMINOR); @@ -865,7 +862,7 @@ tty3270_open(struct tty_struct *tty, struct file * filp) /* why to reassign? */ tty_port_tty_set(&tp->port, tty); tp->inattr = TF_INPUT; - return 0; + return tty_port_install(&tp->port, driver, tty); } if (tty3270_max_index < tty->index + 1) tty3270_max_index = tty->index + 1; @@ -895,7 +892,6 @@ tty3270_open(struct tty_struct *tty, struct file * filp) tty_port_tty_set(&tp->port, tty); tty->low_latency = 0; - tty->driver_data = tp; tty->winsize.ws_row = tp->view.rows - 2; tty->winsize.ws_col = tp->view.cols; @@ -915,6 +911,15 @@ tty3270_open(struct tty_struct *tty, struct file * filp) kbd_ascebc(tp->kbd, tp->view.ascebc); raw3270_activate_view(&tp->view); + + rc = tty_port_install(&tp->port, driver, tty); + if (rc) { + raw3270_put_view(&tp->view); + return rc; + } + + tty->driver_data = tp; + return 0; } @@ -932,10 +937,17 @@ tty3270_close(struct tty_struct *tty, struct file * filp) if (tp) { tty->driver_data = NULL; tty_port_tty_set(&tp->port, NULL); - raw3270_put_view(&tp->view); } } +static void tty3270_cleanup(struct tty_struct *tty) +{ + struct tty3270 *tp = tty->driver_data; + + if (tp) + raw3270_put_view(&tp->view); +} + /* * We always have room. */ @@ -1737,7 +1749,8 @@ static long tty3270_compat_ioctl(struct tty_struct *tty, #endif static const struct tty_operations tty3270_ops = { - .open = tty3270_open, + .install = tty3270_install, + .cleanup = tty3270_cleanup, .close = tty3270_close, .write = tty3270_write, .put_char = tty3270_put_char, @@ -1781,7 +1794,7 @@ static int __init tty3270_init(void) driver->type = TTY_DRIVER_TYPE_SYSTEM; driver->subtype = SYSTEM_TYPE_TTY; driver->init_termios = tty_std_termios; - driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_DYNAMIC_DEV; + driver->flags = TTY_DRIVER_RESET_TERMIOS; tty_set_operations(driver, &tty3270_ops); ret = tty_register_driver(driver); if (ret) { @@ -1800,6 +1813,7 @@ tty3270_exit(void) driver = tty3270_driver; tty3270_driver = NULL; tty_unregister_driver(driver); + put_tty_driver(driver); tty3270_del_views(); } diff --git a/drivers/staging/ipack/devices/ipoctal.c b/drivers/staging/ipack/devices/ipoctal.c index fd0e30132ca2..a68d981c259f 100644 --- a/drivers/staging/ipack/devices/ipoctal.c +++ b/drivers/staging/ipack/devices/ipoctal.c @@ -502,7 +502,7 @@ static int ipoctal_inst_slot(struct ipoctal *ipoctal, unsigned int bus_nr, ipoctal->pointer_read[i] = 0; ipoctal->pointer_write[i] = 0; ipoctal->nb_bytes[i] = 0; - tty_register_device(tty, i, NULL); + tty_port_register_device(&ipoctal->tty_port[i], tty, i, NULL); /* * Enable again the RX. TX will be enabled when @@ -617,7 +617,7 @@ static void ipoctal_set_termios(struct tty_struct *tty, struct ipoctal *ipoctal = tty->driver_data; speed_t baud; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; /* Disable and reset everything before change the setup */ ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.cr, @@ -643,7 +643,7 @@ static void ipoctal_set_termios(struct tty_struct *tty, default: mr1 |= MR1_CHRL_8_BITS; /* By default, select CS8 */ - tty->termios->c_cflag = (cflag & ~CSIZE) | CS8; + tty->termios.c_cflag = (cflag & ~CSIZE) | CS8; break; } @@ -657,7 +657,7 @@ static void ipoctal_set_termios(struct tty_struct *tty, mr1 |= MR1_PARITY_OFF; /* Mark or space parity is not supported */ - tty->termios->c_cflag &= ~CMSPAR; + tty->termios.c_cflag &= ~CMSPAR; /* Set stop bits */ if (cflag & CSTOPB) @@ -690,10 +690,10 @@ static void ipoctal_set_termios(struct tty_struct *tty, } baud = tty_get_baud_rate(tty); - tty_termios_encode_baud_rate(tty->termios, baud, baud); + tty_termios_encode_baud_rate(&tty->termios, baud, baud); /* Set baud rate */ - switch (tty->termios->c_ospeed) { + switch (baud) { case 75: csr |= TX_CLK_75 | RX_CLK_75; break; @@ -734,7 +734,7 @@ static void ipoctal_set_termios(struct tty_struct *tty, default: csr |= TX_CLK_38400 | RX_CLK_38400; /* In case of default, we establish 38400 bps */ - tty_termios_encode_baud_rate(tty->termios, 38400, 38400); + tty_termios_encode_baud_rate(&tty->termios, 38400, 38400); break; } diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c index 8a362f7af379..c90de969be8f 100644 --- a/drivers/staging/serqt_usb2/serqt_usb2.c +++ b/drivers/staging/serqt_usb2/serqt_usb2.c @@ -315,10 +315,8 @@ static void qt_read_bulk_callback(struct urb *urb) } tty = tty_port_tty_get(&port->port); - if (!tty) { - dbg("%s - bad tty pointer - exiting", __func__); + if (!tty) return; - } data = urb->transfer_buffer; @@ -364,7 +362,7 @@ static void qt_read_bulk_callback(struct urb *urb) goto exit; } - if (tty && RxCount) { + if (RxCount) { flag_data = 0; for (i = 0; i < RxCount; ++i) { /* Look ahead code here */ @@ -428,7 +426,7 @@ static void qt_read_bulk_callback(struct urb *urb) dbg("%s - failed resubmitting read urb, error %d", __func__, result); else { - if (tty && RxCount) { + if (RxCount) { tty_flip_buffer_push(tty); tty_schedule_flip(tty); } @@ -897,8 +895,6 @@ static int qt_open(struct tty_struct *tty, * Put this here to make it responsive to stty and defaults set by * the tty layer */ - /* FIXME: is this needed? */ - /* qt_set_termios(tty, port, NULL); */ /* Check to see if we've set up our endpoint info yet */ if (port0->open_ports == 1) { @@ -1195,7 +1191,7 @@ static void qt_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; unsigned char new_LCR = 0; unsigned int cflag = termios->c_cflag; unsigned int index; @@ -1204,7 +1200,7 @@ static void qt_set_termios(struct tty_struct *tty, index = tty->index - port->serial->minor; - switch (cflag) { + switch (cflag & CSIZE) { case CS5: new_LCR |= SERIAL_5_DATA; break; @@ -1215,6 +1211,8 @@ static void qt_set_termios(struct tty_struct *tty, new_LCR |= SERIAL_7_DATA; break; default: + termios->c_cflag &= ~CSIZE; + termios->c_cflag |= CS8; case CS8: new_LCR |= SERIAL_8_DATA; break; @@ -1301,7 +1299,7 @@ static void qt_set_termios(struct tty_struct *tty, dbg(__FILE__ "BoxSetSW_FlowCtrl (diabling) failed\n"); } - tty->termios->c_cflag &= ~CMSPAR; + termios->c_cflag &= ~CMSPAR; /* FIXME: Error cases should be returning the actual bits changed only */ } diff --git a/drivers/tty/amiserial.c b/drivers/tty/amiserial.c index 6cc4358f68c1..2b7535d42e05 100644 --- a/drivers/tty/amiserial.c +++ b/drivers/tty/amiserial.c @@ -646,7 +646,7 @@ static void shutdown(struct tty_struct *tty, struct serial_state *info) custom.adkcon = AC_UARTBRK; mb(); - if (tty->termios->c_cflag & HUPCL) + if (tty->termios.c_cflag & HUPCL) info->MCR &= ~(SER_DTR|SER_RTS); rtsdtr_ctrl(info->MCR); @@ -670,7 +670,7 @@ static void change_speed(struct tty_struct *tty, struct serial_state *info, int bits; unsigned long flags; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; /* Byte size is always 8 bits plus parity bit if requested */ @@ -707,8 +707,8 @@ static void change_speed(struct tty_struct *tty, struct serial_state *info, /* If the quotient is zero refuse the change */ if (!quot && old_termios) { /* FIXME: Will need updating for new tty in the end */ - tty->termios->c_cflag &= ~CBAUD; - tty->termios->c_cflag |= (old_termios->c_cflag & CBAUD); + tty->termios.c_cflag &= ~CBAUD; + tty->termios.c_cflag |= (old_termios->c_cflag & CBAUD); baud = tty_get_baud_rate(tty); if (!baud) baud = 9600; @@ -984,7 +984,7 @@ static void rs_throttle(struct tty_struct * tty) if (I_IXOFF(tty)) rs_send_xchar(tty, STOP_CHAR(tty)); - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) info->MCR &= ~SER_RTS; local_irq_save(flags); @@ -1012,7 +1012,7 @@ static void rs_unthrottle(struct tty_struct * tty) else rs_send_xchar(tty, START_CHAR(tty)); } - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) info->MCR |= SER_RTS; local_irq_save(flags); rtsdtr_ctrl(info->MCR); @@ -1033,7 +1033,7 @@ static int get_serial_info(struct tty_struct *tty, struct serial_state *state, if (!retinfo) return -EFAULT; memset(&tmp, 0, sizeof(tmp)); - tty_lock(); + tty_lock(tty); tmp.line = tty->index; tmp.port = state->port; tmp.flags = state->tport.flags; @@ -1042,7 +1042,7 @@ static int get_serial_info(struct tty_struct *tty, struct serial_state *state, tmp.close_delay = state->tport.close_delay; tmp.closing_wait = state->tport.closing_wait; tmp.custom_divisor = state->custom_divisor; - tty_unlock(); + tty_unlock(tty); if (copy_to_user(retinfo,&tmp,sizeof(*retinfo))) return -EFAULT; return 0; @@ -1059,12 +1059,12 @@ static int set_serial_info(struct tty_struct *tty, struct serial_state *state, if (copy_from_user(&new_serial,new_info,sizeof(new_serial))) return -EFAULT; - tty_lock(); + tty_lock(tty); change_spd = ((new_serial.flags ^ port->flags) & ASYNC_SPD_MASK) || new_serial.custom_divisor != state->custom_divisor; if (new_serial.irq || new_serial.port != state->port || new_serial.xmit_fifo_size != state->xmit_fifo_size) { - tty_unlock(); + tty_unlock(tty); return -EINVAL; } @@ -1074,7 +1074,7 @@ static int set_serial_info(struct tty_struct *tty, struct serial_state *state, (new_serial.xmit_fifo_size != state->xmit_fifo_size) || ((new_serial.flags & ~ASYNC_USR_MASK) != (port->flags & ~ASYNC_USR_MASK))) { - tty_unlock(); + tty_unlock(tty); return -EPERM; } port->flags = ((port->flags & ~ASYNC_USR_MASK) | @@ -1084,7 +1084,7 @@ static int set_serial_info(struct tty_struct *tty, struct serial_state *state, } if (new_serial.baud_base < 9600) { - tty_unlock(); + tty_unlock(tty); return -EINVAL; } @@ -1116,7 +1116,7 @@ check_and_exit: } } else retval = startup(tty, state); - tty_unlock(); + tty_unlock(tty); return retval; } @@ -1330,7 +1330,7 @@ static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) { struct serial_state *info = tty->driver_data; unsigned long flags; - unsigned int cflag = tty->termios->c_cflag; + unsigned int cflag = tty->termios.c_cflag; change_speed(tty, info, old_termios); @@ -1347,7 +1347,7 @@ static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) { info->MCR |= SER_DTR; - if (!(tty->termios->c_cflag & CRTSCTS) || + if (!(tty->termios.c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags)) { info->MCR |= SER_RTS; } @@ -1358,7 +1358,7 @@ static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) /* Handle turning off CRTSCTS */ if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; rs_start(tty); } @@ -1371,7 +1371,7 @@ static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) * or not. Hence, this may change..... */ if (!(old_termios->c_cflag & CLOCAL) && - (tty->termios->c_cflag & CLOCAL)) + (tty->termios.c_cflag & CLOCAL)) wake_up_interruptible(&info->open_wait); #endif } @@ -1710,10 +1710,6 @@ static int __init amiga_serial_probe(struct platform_device *pdev) serial_driver->flags = TTY_DRIVER_REAL_RAW; tty_set_operations(serial_driver, &serial_ops); - error = tty_register_driver(serial_driver); - if (error) - goto fail_put_tty_driver; - state = rs_table; state->port = (int)&custom.serdatr; /* Just to give it a value */ state->custom_divisor = 0; @@ -1724,6 +1720,11 @@ static int __init amiga_serial_probe(struct platform_device *pdev) state->icount.overrun = state->icount.brk = 0; tty_port_init(&state->tport); state->tport.ops = &amiga_port_ops; + tty_port_link_device(&state->tport, serial_driver, 0); + + error = tty_register_driver(serial_driver); + if (error) + goto fail_put_tty_driver; printk(KERN_INFO "ttyS0 is the amiga builtin serial port\n"); diff --git a/drivers/tty/bfin_jtag_comm.c b/drivers/tty/bfin_jtag_comm.c index 61fc74fe1747..02b7d3a09696 100644 --- a/drivers/tty/bfin_jtag_comm.c +++ b/drivers/tty/bfin_jtag_comm.c @@ -263,6 +263,7 @@ static int __init bfin_jc_init(void) bfin_jc_driver->subtype = SERIAL_TYPE_NORMAL; bfin_jc_driver->init_termios = tty_std_termios; tty_set_operations(bfin_jc_driver, &bfin_jc_ops); + tty_port_link_device(&port, bfin_jc_driver, 0); ret = tty_register_driver(bfin_jc_driver); if (ret) diff --git a/drivers/tty/cyclades.c b/drivers/tty/cyclades.c index e61cabdd69df..e3954dae5064 100644 --- a/drivers/tty/cyclades.c +++ b/drivers/tty/cyclades.c @@ -1459,7 +1459,7 @@ static void cy_shutdown(struct cyclades_port *info, struct tty_struct *tty) info->port.xmit_buf = NULL; free_page((unsigned long)temp); } - if (tty->termios->c_cflag & HUPCL) + if (tty->termios.c_cflag & HUPCL) cyy_change_rts_dtr(info, 0, TIOCM_RTS | TIOCM_DTR); cyy_issue_cmd(info, CyCHAN_CTL | CyDIS_RCVR); @@ -1488,7 +1488,7 @@ static void cy_shutdown(struct cyclades_port *info, struct tty_struct *tty) free_page((unsigned long)temp); } - if (tty->termios->c_cflag & HUPCL) + if (tty->termios.c_cflag & HUPCL) tty_port_lower_dtr_rts(&info->port); set_bit(TTY_IO_ERROR, &tty->flags); @@ -1599,7 +1599,7 @@ static int cy_open(struct tty_struct *tty, struct file *filp) * If the port is the middle of closing, bail out now */ if (tty_hung_up_p(filp) || (info->port.flags & ASYNC_CLOSING)) { - wait_event_interruptible_tty(info->port.close_wait, + wait_event_interruptible_tty(tty, info->port.close_wait, !(info->port.flags & ASYNC_CLOSING)); return (info->port.flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS; } @@ -1999,14 +1999,11 @@ static void cy_set_line_char(struct cyclades_port *info, struct tty_struct *tty) int baud, baud_rate = 0; int i; - if (!tty->termios) /* XXX can this happen at all? */ - return; - if (info->line == -1) return; - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; + cflag = tty->termios.c_cflag; + iflag = tty->termios.c_iflag; /* * Set up the tty->alt_speed kludge @@ -2825,7 +2822,7 @@ static void cy_set_termios(struct tty_struct *tty, struct ktermios *old_termios) cy_set_line_char(info, tty); if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; cy_start(tty); } @@ -2837,7 +2834,7 @@ static void cy_set_termios(struct tty_struct *tty, struct ktermios *old_termios) * or not. Hence, this may change..... */ if (!(old_termios->c_cflag & CLOCAL) && - (tty->termios->c_cflag & CLOCAL)) + (tty->termios.c_cflag & CLOCAL)) wake_up_interruptible(&info->port.open_wait); #endif } /* cy_set_termios */ @@ -2899,7 +2896,7 @@ static void cy_throttle(struct tty_struct *tty) info->throttle = 1; } - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { if (!cy_is_Z(card)) { spin_lock_irqsave(&card->card_lock, flags); cyy_change_rts_dtr(info, 0, TIOCM_RTS); @@ -2938,7 +2935,7 @@ static void cy_unthrottle(struct tty_struct *tty) cy_send_xchar(tty, START_CHAR(tty)); } - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { card = info->card; if (!cy_is_Z(card)) { spin_lock_irqsave(&card->card_lock, flags); @@ -3289,9 +3286,10 @@ static unsigned short __devinit cyy_init_card(void __iomem *true_base_addr, static int __init cy_detect_isa(void) { #ifdef CONFIG_ISA + struct cyclades_card *card; unsigned short cy_isa_irq, nboard; void __iomem *cy_isa_address; - unsigned short i, j, cy_isa_nchan; + unsigned short i, j, k, cy_isa_nchan; int isparam = 0; nboard = 0; @@ -3349,7 +3347,8 @@ static int __init cy_detect_isa(void) } /* fill the next cy_card structure available */ for (j = 0; j < NR_CARDS; j++) { - if (cy_card[j].base_addr == NULL) + card = &cy_card[j]; + if (card->base_addr == NULL) break; } if (j == NR_CARDS) { /* no more cy_cards available */ @@ -3363,7 +3362,7 @@ static int __init cy_detect_isa(void) /* allocate IRQ */ if (request_irq(cy_isa_irq, cyy_interrupt, - 0, "Cyclom-Y", &cy_card[j])) { + 0, "Cyclom-Y", card)) { printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but " "could not allocate IRQ#%d.\n", (unsigned long)cy_isa_address, cy_isa_irq); @@ -3372,16 +3371,16 @@ static int __init cy_detect_isa(void) } /* set cy_card */ - cy_card[j].base_addr = cy_isa_address; - cy_card[j].ctl_addr.p9050 = NULL; - cy_card[j].irq = (int)cy_isa_irq; - cy_card[j].bus_index = 0; - cy_card[j].first_line = cy_next_channel; - cy_card[j].num_chips = cy_isa_nchan / CyPORTS_PER_CHIP; - cy_card[j].nports = cy_isa_nchan; - if (cy_init_card(&cy_card[j])) { - cy_card[j].base_addr = NULL; - free_irq(cy_isa_irq, &cy_card[j]); + card->base_addr = cy_isa_address; + card->ctl_addr.p9050 = NULL; + card->irq = (int)cy_isa_irq; + card->bus_index = 0; + card->first_line = cy_next_channel; + card->num_chips = cy_isa_nchan / CyPORTS_PER_CHIP; + card->nports = cy_isa_nchan; + if (cy_init_card(card)) { + card->base_addr = NULL; + free_irq(cy_isa_irq, card); iounmap(cy_isa_address); continue; } @@ -3393,9 +3392,10 @@ static int __init cy_detect_isa(void) (unsigned long)(cy_isa_address + (CyISA_Ywin - 1)), cy_isa_irq, cy_isa_nchan, cy_next_channel); - for (j = cy_next_channel; - j < cy_next_channel + cy_isa_nchan; j++) - tty_register_device(cy_serial_driver, j, NULL); + for (k = 0, j = cy_next_channel; + j < cy_next_channel + cy_isa_nchan; j++, k++) + tty_port_register_device(&card->ports[k].port, + cy_serial_driver, j, NULL); cy_next_channel += cy_isa_nchan; } return nboard; @@ -3695,10 +3695,11 @@ err: static int __devinit cy_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { + struct cyclades_card *card; void __iomem *addr0 = NULL, *addr2 = NULL; char *card_name = NULL; u32 uninitialized_var(mailbox); - unsigned int device_id, nchan = 0, card_no, i; + unsigned int device_id, nchan = 0, card_no, i, j; unsigned char plx_ver; int retval, irq; @@ -3829,7 +3830,8 @@ static int __devinit cy_pci_probe(struct pci_dev *pdev, } /* fill the next cy_card structure available */ for (card_no = 0; card_no < NR_CARDS; card_no++) { - if (cy_card[card_no].base_addr == NULL) + card = &cy_card[card_no]; + if (card->base_addr == NULL) break; } if (card_no == NR_CARDS) { /* no more cy_cards available */ @@ -3843,27 +3845,26 @@ static int __devinit cy_pci_probe(struct pci_dev *pdev, device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) { /* allocate IRQ */ retval = request_irq(irq, cyy_interrupt, - IRQF_SHARED, "Cyclom-Y", &cy_card[card_no]); + IRQF_SHARED, "Cyclom-Y", card); if (retval) { dev_err(&pdev->dev, "could not allocate IRQ\n"); goto err_unmap; } - cy_card[card_no].num_chips = nchan / CyPORTS_PER_CHIP; + card->num_chips = nchan / CyPORTS_PER_CHIP; } else { struct FIRM_ID __iomem *firm_id = addr2 + ID_ADDRESS; struct ZFW_CTRL __iomem *zfw_ctrl; zfw_ctrl = addr2 + (readl(&firm_id->zfwctrl_addr) & 0xfffff); - cy_card[card_no].hw_ver = mailbox; - cy_card[card_no].num_chips = (unsigned int)-1; - cy_card[card_no].board_ctrl = &zfw_ctrl->board_ctrl; + card->hw_ver = mailbox; + card->num_chips = (unsigned int)-1; + card->board_ctrl = &zfw_ctrl->board_ctrl; #ifdef CONFIG_CYZ_INTR /* allocate IRQ only if board has an IRQ */ if (irq != 0 && irq != 255) { retval = request_irq(irq, cyz_interrupt, - IRQF_SHARED, "Cyclades-Z", - &cy_card[card_no]); + IRQF_SHARED, "Cyclades-Z", card); if (retval) { dev_err(&pdev->dev, "could not allocate IRQ\n"); goto err_unmap; @@ -3873,17 +3874,17 @@ static int __devinit cy_pci_probe(struct pci_dev *pdev, } /* set cy_card */ - cy_card[card_no].base_addr = addr2; - cy_card[card_no].ctl_addr.p9050 = addr0; - cy_card[card_no].irq = irq; - cy_card[card_no].bus_index = 1; - cy_card[card_no].first_line = cy_next_channel; - cy_card[card_no].nports = nchan; - retval = cy_init_card(&cy_card[card_no]); + card->base_addr = addr2; + card->ctl_addr.p9050 = addr0; + card->irq = irq; + card->bus_index = 1; + card->first_line = cy_next_channel; + card->nports = nchan; + retval = cy_init_card(card); if (retval) goto err_null; - pci_set_drvdata(pdev, &cy_card[card_no]); + pci_set_drvdata(pdev, card); if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo || device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) { @@ -3909,14 +3910,15 @@ static int __devinit cy_pci_probe(struct pci_dev *pdev, dev_info(&pdev->dev, "%s/PCI #%d found: %d channels starting from " "port %d.\n", card_name, card_no + 1, nchan, cy_next_channel); - for (i = cy_next_channel; i < cy_next_channel + nchan; i++) - tty_register_device(cy_serial_driver, i, &pdev->dev); + for (j = 0, i = cy_next_channel; i < cy_next_channel + nchan; i++, j++) + tty_port_register_device(&card->ports[j].port, + cy_serial_driver, i, &pdev->dev); cy_next_channel += nchan; return 0; err_null: - cy_card[card_no].base_addr = NULL; - free_irq(irq, &cy_card[card_no]); + card->base_addr = NULL; + free_irq(irq, card); err_unmap: iounmap(addr0); if (addr2) diff --git a/drivers/tty/ehv_bytechan.c b/drivers/tty/ehv_bytechan.c index 4813684cb634..4ab936b7aac6 100644 --- a/drivers/tty/ehv_bytechan.c +++ b/drivers/tty/ehv_bytechan.c @@ -738,16 +738,17 @@ static int __devinit ehv_bc_tty_probe(struct platform_device *pdev) goto error; } - bc->dev = tty_register_device(ehv_bc_driver, i, &pdev->dev); + tty_port_init(&bc->port); + bc->port.ops = &ehv_bc_tty_port_ops; + + bc->dev = tty_port_register_device(&bc->port, ehv_bc_driver, i, + &pdev->dev); if (IS_ERR(bc->dev)) { ret = PTR_ERR(bc->dev); dev_err(&pdev->dev, "could not register tty (ret=%i)\n", ret); goto error; } - tty_port_init(&bc->port); - bc->port.ops = &ehv_bc_tty_port_ops; - dev_set_drvdata(&pdev->dev, bc); dev_info(&pdev->dev, "registered /dev/%s%u for byte channel %u\n", diff --git a/drivers/tty/hvc/hvc_console.c b/drivers/tty/hvc/hvc_console.c index 2d691eb7c40a..7f80f15681cd 100644 --- a/drivers/tty/hvc/hvc_console.c +++ b/drivers/tty/hvc/hvc_console.c @@ -299,20 +299,33 @@ static void hvc_unthrottle(struct tty_struct *tty) hvc_kick(); } +static int hvc_install(struct tty_driver *driver, struct tty_struct *tty) +{ + struct hvc_struct *hp; + int rc; + + /* Auto increments kref reference if found. */ + if (!(hp = hvc_get_by_index(tty->index))) + return -ENODEV; + + tty->driver_data = hp; + + rc = tty_port_install(&hp->port, driver, tty); + if (rc) + tty_port_put(&hp->port); + return rc; +} + /* * The TTY interface won't be used until after the vio layer has exposed the vty * adapter to the kernel. */ static int hvc_open(struct tty_struct *tty, struct file * filp) { - struct hvc_struct *hp; + struct hvc_struct *hp = tty->driver_data; unsigned long flags; int rc = 0; - /* Auto increments kref reference if found. */ - if (!(hp = hvc_get_by_index(tty->index))) - return -ENODEV; - spin_lock_irqsave(&hp->port.lock, flags); /* Check and then increment for fast path open. */ if (hp->port.count++ > 0) { @@ -322,7 +335,6 @@ static int hvc_open(struct tty_struct *tty, struct file * filp) } /* else count == 0 */ spin_unlock_irqrestore(&hp->port.lock, flags); - tty->driver_data = hp; tty_port_tty_set(&hp->port, tty); if (hp->ops->notifier_add) @@ -389,6 +401,11 @@ static void hvc_close(struct tty_struct *tty, struct file * filp) hp->vtermno, hp->port.count); spin_unlock_irqrestore(&hp->port.lock, flags); } +} + +static void hvc_cleanup(struct tty_struct *tty) +{ + struct hvc_struct *hp = tty->driver_data; tty_port_put(&hp->port); } @@ -792,8 +809,10 @@ static void hvc_poll_put_char(struct tty_driver *driver, int line, char ch) #endif static const struct tty_operations hvc_ops = { + .install = hvc_install, .open = hvc_open, .close = hvc_close, + .cleanup = hvc_cleanup, .write = hvc_write, .hangup = hvc_hangup, .unthrottle = hvc_unthrottle, diff --git a/drivers/tty/hvc/hvcs.c b/drivers/tty/hvc/hvcs.c index d56788c83974..cab5c7adf8e8 100644 --- a/drivers/tty/hvc/hvcs.c +++ b/drivers/tty/hvc/hvcs.c @@ -1102,27 +1102,20 @@ static struct hvcs_struct *hvcs_get_by_index(int index) return NULL; } -/* - * This is invoked via the tty_open interface when a user app connects to the - * /dev node. - */ -static int hvcs_open(struct tty_struct *tty, struct file *filp) +static int hvcs_install(struct tty_driver *driver, struct tty_struct *tty) { struct hvcs_struct *hvcsd; - int rc, retval = 0; - unsigned long flags; - unsigned int irq; struct vio_dev *vdev; - unsigned long unit_address; - - if (tty->driver_data) - goto fast_open; + unsigned long unit_address, flags; + unsigned int irq; + int retval; /* * Is there a vty-server that shares the same index? * This function increments the kref index. */ - if (!(hvcsd = hvcs_get_by_index(tty->index))) { + hvcsd = hvcs_get_by_index(tty->index); + if (!hvcsd) { printk(KERN_WARNING "HVCS: open failed, no device associated" " with tty->index %d.\n", tty->index); return -ENODEV; @@ -1130,11 +1123,16 @@ static int hvcs_open(struct tty_struct *tty, struct file *filp) spin_lock_irqsave(&hvcsd->lock, flags); - if (hvcsd->connected == 0) - if ((retval = hvcs_partner_connect(hvcsd))) - goto error_release; + if (hvcsd->connected == 0) { + retval = hvcs_partner_connect(hvcsd); + if (retval) { + spin_unlock_irqrestore(&hvcsd->lock, flags); + printk(KERN_WARNING "HVCS: partner connect failed.\n"); + goto err_put; + } + } - hvcsd->port.count = 1; + hvcsd->port.count = 0; hvcsd->port.tty = tty; tty->driver_data = hvcsd; @@ -1155,37 +1153,48 @@ static int hvcs_open(struct tty_struct *tty, struct file *filp) * This must be done outside of the spinlock because it requests irqs * and will grab the spinlock and free the connection if it fails. */ - if (((rc = hvcs_enable_device(hvcsd, unit_address, irq, vdev)))) { - tty_port_put(&hvcsd->port); + retval = hvcs_enable_device(hvcsd, unit_address, irq, vdev); + if (retval) { printk(KERN_WARNING "HVCS: enable device failed.\n"); - return rc; + goto err_put; } - goto open_success; + retval = tty_port_install(&hvcsd->port, driver, tty); + if (retval) + goto err_irq; -fast_open: - hvcsd = tty->driver_data; + return 0; +err_irq: + spin_lock_irqsave(&hvcsd->lock, flags); + vio_disable_interrupts(hvcsd->vdev); + spin_unlock_irqrestore(&hvcsd->lock, flags); + free_irq(irq, hvcsd); +err_put: + tty_port_put(&hvcsd->port); + + return retval; +} + +/* + * This is invoked via the tty_open interface when a user app connects to the + * /dev node. + */ +static int hvcs_open(struct tty_struct *tty, struct file *filp) +{ + struct hvcs_struct *hvcsd = tty->driver_data; + unsigned long flags; spin_lock_irqsave(&hvcsd->lock, flags); - tty_port_get(&hvcsd->port); hvcsd->port.count++; hvcsd->todo_mask |= HVCS_SCHED_READ; spin_unlock_irqrestore(&hvcsd->lock, flags); -open_success: hvcs_kick(); printk(KERN_INFO "HVCS: vty-server@%X connection opened.\n", hvcsd->vdev->unit_address ); return 0; - -error_release: - spin_unlock_irqrestore(&hvcsd->lock, flags); - tty_port_put(&hvcsd->port); - - printk(KERN_WARNING "HVCS: partner connect failed.\n"); - return retval; } static void hvcs_close(struct tty_struct *tty, struct file *filp) @@ -1236,7 +1245,6 @@ static void hvcs_close(struct tty_struct *tty, struct file *filp) tty->driver_data = NULL; free_irq(irq, hvcsd); - tty_port_put(&hvcsd->port); return; } else if (hvcsd->port.count < 0) { printk(KERN_ERR "HVCS: vty-server@%X open_count: %d" @@ -1245,6 +1253,12 @@ static void hvcs_close(struct tty_struct *tty, struct file *filp) } spin_unlock_irqrestore(&hvcsd->lock, flags); +} + +static void hvcs_cleanup(struct tty_struct * tty) +{ + struct hvcs_struct *hvcsd = tty->driver_data; + tty_port_put(&hvcsd->port); } @@ -1431,8 +1445,10 @@ static int hvcs_chars_in_buffer(struct tty_struct *tty) } static const struct tty_operations hvcs_ops = { + .install = hvcs_install, .open = hvcs_open, .close = hvcs_close, + .cleanup = hvcs_cleanup, .hangup = hvcs_hangup, .write = hvcs_write, .write_room = hvcs_write_room, diff --git a/drivers/tty/hvc/hvsi.c b/drivers/tty/hvc/hvsi.c index 6f5bc49c441f..0083bc1f63f4 100644 --- a/drivers/tty/hvc/hvsi.c +++ b/drivers/tty/hvc/hvsi.c @@ -1080,6 +1080,8 @@ static int __init hvsi_init(void) struct hvsi_struct *hp = &hvsi_ports[i]; int ret = 1; + tty_port_link_device(&hp->port, hvsi_driver, i); + ret = request_irq(hp->virq, hvsi_interrupt, 0, "hvsi", hp); if (ret) printk(KERN_ERR "HVSI: couldn't reserve irq 0x%x (error %i)\n", diff --git a/drivers/tty/hvc/hvsi_lib.c b/drivers/tty/hvc/hvsi_lib.c index 59c135dd5d20..3396eb9d57a3 100644 --- a/drivers/tty/hvc/hvsi_lib.c +++ b/drivers/tty/hvc/hvsi_lib.c @@ -400,7 +400,7 @@ void hvsilib_close(struct hvsi_priv *pv, struct hvc_struct *hp) spin_unlock_irqrestore(&hp->lock, flags); /* Clear our own DTR */ - if (!pv->tty || (pv->tty->termios->c_cflag & HUPCL)) + if (!pv->tty || (pv->tty->termios.c_cflag & HUPCL)) hvsilib_write_mctrl(pv, 0); /* Tear down the connection */ diff --git a/drivers/tty/ipwireless/tty.c b/drivers/tty/ipwireless/tty.c index f8b5fa0093a3..160f0ad9589d 100644 --- a/drivers/tty/ipwireless/tty.c +++ b/drivers/tty/ipwireless/tty.c @@ -476,7 +476,7 @@ static int add_tty(int j, mutex_init(&ttys[j]->ipw_tty_mutex); tty_port_init(&ttys[j]->port); - tty_register_device(ipw_tty_driver, j, NULL); + tty_port_register_device(&ttys[j]->port, ipw_tty_driver, j, NULL); ipwireless_associate_network_tty(network, channel_idx, ttys[j]); if (secondary_channel_idx != -1) diff --git a/drivers/tty/isicom.c b/drivers/tty/isicom.c index e1235accab74..99cf22e5f2b6 100644 --- a/drivers/tty/isicom.c +++ b/drivers/tty/isicom.c @@ -702,7 +702,7 @@ static void isicom_config_port(struct tty_struct *tty) /* 1,2,3,4 => 57.6, 115.2, 230, 460 kbps resp. */ if (baud < 1 || baud > 4) - tty->termios->c_cflag &= ~CBAUDEX; + tty->termios.c_cflag &= ~CBAUDEX; else baud += 15; } @@ -1196,8 +1196,8 @@ static void isicom_set_termios(struct tty_struct *tty, if (isicom_paranoia_check(port, tty->name, "isicom_set_termios")) return; - if (tty->termios->c_cflag == old_termios->c_cflag && - tty->termios->c_iflag == old_termios->c_iflag) + if (tty->termios.c_cflag == old_termios->c_cflag && + tty->termios.c_iflag == old_termios->c_iflag) return; spin_lock_irqsave(&port->card->card_lock, flags); @@ -1205,7 +1205,7 @@ static void isicom_set_termios(struct tty_struct *tty, spin_unlock_irqrestore(&port->card->card_lock, flags); if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; isicom_start(tty); } @@ -1611,7 +1611,8 @@ static int __devinit isicom_probe(struct pci_dev *pdev, goto errunri; for (index = 0; index < board->port_count; index++) - tty_register_device(isicom_normal, board->index * 16 + index, + tty_port_register_device(&board->ports[index].port, + isicom_normal, board->index * 16 + index, &pdev->dev); return 0; diff --git a/drivers/tty/moxa.c b/drivers/tty/moxa.c index 324467d28a54..56e616b9109a 100644 --- a/drivers/tty/moxa.c +++ b/drivers/tty/moxa.c @@ -169,6 +169,7 @@ static DEFINE_SPINLOCK(moxa_lock); static unsigned long baseaddr[MAX_BOARDS]; static unsigned int type[MAX_BOARDS]; static unsigned int numports[MAX_BOARDS]; +static struct tty_port moxa_service_port; MODULE_AUTHOR("William Chen"); MODULE_DESCRIPTION("MOXA Intellio Family Multiport Board Device Driver"); @@ -367,10 +368,10 @@ static int moxa_ioctl(struct tty_struct *tty, tmp.dcd = 1; ttyp = tty_port_tty_get(&p->port); - if (!ttyp || !ttyp->termios) + if (!ttyp) tmp.cflag = p->cflag; else - tmp.cflag = ttyp->termios->c_cflag; + tmp.cflag = ttyp->termios.c_cflag; tty_kref_put(ttyp); copy: if (copy_to_user(argm, &tmp, sizeof(tmp))) @@ -834,7 +835,7 @@ static int moxa_init_board(struct moxa_board_conf *brd, struct device *dev) const struct firmware *fw; const char *file; struct moxa_port *p; - unsigned int i; + unsigned int i, first_idx; int ret; brd->ports = kcalloc(MAX_PORTS_PER_BOARD, sizeof(*brd->ports), @@ -887,6 +888,11 @@ static int moxa_init_board(struct moxa_board_conf *brd, struct device *dev) mod_timer(&moxaTimer, jiffies + HZ / 50); spin_unlock_bh(&moxa_lock); + first_idx = (brd - moxa_boards) * MAX_PORTS_PER_BOARD; + for (i = 0; i < brd->numPorts; i++) + tty_port_register_device(&brd->ports[i].port, moxaDriver, + first_idx + i, dev); + return 0; err_free: kfree(brd->ports); @@ -896,7 +902,7 @@ err: static void moxa_board_deinit(struct moxa_board_conf *brd) { - unsigned int a, opened; + unsigned int a, opened, first_idx; mutex_lock(&moxa_openlock); spin_lock_bh(&moxa_lock); @@ -925,6 +931,10 @@ static void moxa_board_deinit(struct moxa_board_conf *brd) mutex_lock(&moxa_openlock); } + first_idx = (brd - moxa_boards) * MAX_PORTS_PER_BOARD; + for (a = 0; a < brd->numPorts; a++) + tty_unregister_device(moxaDriver, first_idx + a); + iounmap(brd->basemem); brd->basemem = NULL; kfree(brd->ports); @@ -967,6 +977,7 @@ static int __devinit moxa_pci_probe(struct pci_dev *pdev, board->basemem = ioremap_nocache(pci_resource_start(pdev, 2), 0x4000); if (board->basemem == NULL) { dev_err(&pdev->dev, "can't remap io space 2\n"); + retval = -ENOMEM; goto err_reg; } @@ -1031,9 +1042,14 @@ static int __init moxa_init(void) printk(KERN_INFO "MOXA Intellio family driver version %s\n", MOXA_VERSION); - moxaDriver = alloc_tty_driver(MAX_PORTS + 1); - if (!moxaDriver) - return -ENOMEM; + + tty_port_init(&moxa_service_port); + + moxaDriver = tty_alloc_driver(MAX_PORTS + 1, + TTY_DRIVER_REAL_RAW | + TTY_DRIVER_DYNAMIC_DEV); + if (IS_ERR(moxaDriver)) + return PTR_ERR(moxaDriver); moxaDriver->name = "ttyMX"; moxaDriver->major = ttymajor; @@ -1044,8 +1060,9 @@ static int __init moxa_init(void) moxaDriver->init_termios.c_cflag = B9600 | CS8 | CREAD | CLOCAL | HUPCL; moxaDriver->init_termios.c_ispeed = 9600; moxaDriver->init_termios.c_ospeed = 9600; - moxaDriver->flags = TTY_DRIVER_REAL_RAW; tty_set_operations(moxaDriver, &moxa_ops); + /* Having one more port only for ioctls is ugly */ + tty_port_link_device(&moxa_service_port, moxaDriver, MAX_PORTS); if (tty_register_driver(moxaDriver)) { printk(KERN_ERR "can't register MOXA Smartio tty driver!\n"); @@ -1178,7 +1195,7 @@ static int moxa_open(struct tty_struct *tty, struct file *filp) mutex_lock(&ch->port.mutex); if (!(ch->port.flags & ASYNC_INITIALIZED)) { ch->statusflags = 0; - moxa_set_tty_param(tty, tty->termios); + moxa_set_tty_param(tty, &tty->termios); MoxaPortLineCtrl(ch, 1, 1); MoxaPortEnable(ch); MoxaSetFifo(ch, ch->type == PORT_16550A); @@ -1193,7 +1210,7 @@ static int moxa_open(struct tty_struct *tty, struct file *filp) static void moxa_close(struct tty_struct *tty, struct file *filp) { struct moxa_port *ch = tty->driver_data; - ch->cflag = tty->termios->c_cflag; + ch->cflag = tty->termios.c_cflag; tty_port_close(&ch->port, tty, filp); } @@ -1464,7 +1481,7 @@ static void moxa_poll(unsigned long ignored) static void moxa_set_tty_param(struct tty_struct *tty, struct ktermios *old_termios) { - register struct ktermios *ts = tty->termios; + register struct ktermios *ts = &tty->termios; struct moxa_port *ch = tty->driver_data; int rts, cts, txflow, rxflow, xany, baud; diff --git a/drivers/tty/mxser.c b/drivers/tty/mxser.c index 90cc680c4f0e..bb2da4ca8257 100644 --- a/drivers/tty/mxser.c +++ b/drivers/tty/mxser.c @@ -643,7 +643,7 @@ static int mxser_change_speed(struct tty_struct *tty, int ret = 0; unsigned char status; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; if (!info->ioaddr) return ret; @@ -1520,10 +1520,10 @@ static int mxser_ioctl_special(unsigned int cmd, void __user *argp) tty = tty_port_tty_get(port); - if (!tty || !tty->termios) + if (!tty) ms.cflag = ip->normal_termios.c_cflag; else - ms.cflag = tty->termios->c_cflag; + ms.cflag = tty->termios.c_cflag; tty_kref_put(tty); spin_lock_irq(&ip->slock); status = inb(ip->ioaddr + UART_MSR); @@ -1589,13 +1589,13 @@ static int mxser_ioctl_special(unsigned int cmd, void __user *argp) tty = tty_port_tty_get(&ip->port); - if (!tty || !tty->termios) { + if (!tty) { cflag = ip->normal_termios.c_cflag; iflag = ip->normal_termios.c_iflag; me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios); } else { - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; + cflag = tty->termios.c_cflag; + iflag = tty->termios.c_iflag; me->baudrate[p] = tty_get_baud_rate(tty); } tty_kref_put(tty); @@ -1853,7 +1853,7 @@ static void mxser_stoprx(struct tty_struct *tty) } } - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { info->MCR &= ~UART_MCR_RTS; outb(info->MCR, info->ioaddr + UART_MCR); } @@ -1890,7 +1890,7 @@ static void mxser_unthrottle(struct tty_struct *tty) } } - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { info->MCR |= UART_MCR_RTS; outb(info->MCR, info->ioaddr + UART_MCR); } @@ -1939,14 +1939,14 @@ static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termi spin_unlock_irqrestore(&info->slock, flags); if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; mxser_start(tty); } /* Handle sw stopped */ if ((old_termios->c_iflag & IXON) && - !(tty->termios->c_iflag & IXON)) { + !(tty->termios.c_iflag & IXON)) { tty->stopped = 0; if (info->board->chip_flag) { @@ -2337,11 +2337,36 @@ static struct tty_port_operations mxser_port_ops = { * The MOXA Smartio/Industio serial driver boot-time initialization code! */ +static bool allow_overlapping_vector; +module_param(allow_overlapping_vector, bool, S_IRUGO); +MODULE_PARM_DESC(allow_overlapping_vector, "whether we allow ISA cards to be configured such that vector overlabs IO ports (default=no)"); + +static bool mxser_overlapping_vector(struct mxser_board *brd) +{ + return allow_overlapping_vector && + brd->vector >= brd->ports[0].ioaddr && + brd->vector < brd->ports[0].ioaddr + 8 * brd->info->nports; +} + +static int mxser_request_vector(struct mxser_board *brd) +{ + if (mxser_overlapping_vector(brd)) + return 0; + return request_region(brd->vector, 1, "mxser(vector)") ? 0 : -EIO; +} + +static void mxser_release_vector(struct mxser_board *brd) +{ + if (mxser_overlapping_vector(brd)) + return; + release_region(brd->vector, 1); +} + static void mxser_release_ISA_res(struct mxser_board *brd) { free_irq(brd->irq, brd); release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); - release_region(brd->vector, 1); + mxser_release_vector(brd); } static int __devinit mxser_initbrd(struct mxser_board *brd, @@ -2396,7 +2421,7 @@ static int __devinit mxser_initbrd(struct mxser_board *brd, static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd) { - int id, i, bits; + int id, i, bits, ret; unsigned short regs[16], irq; unsigned char scratch, scratch2; @@ -2492,13 +2517,15 @@ static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd) 8 * brd->info->nports - 1); return -EIO; } - if (!request_region(brd->vector, 1, "mxser(vector)")) { + + ret = mxser_request_vector(brd); + if (ret) { release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); printk(KERN_ERR "mxser: can't request interrupt vector region: " "0x%.8lx-0x%.8lx\n", brd->ports[0].ioaddr, brd->ports[0].ioaddr + 8 * brd->info->nports - 1); - return -EIO; + return ret; } return brd->info->nports; @@ -2598,7 +2625,8 @@ static int __devinit mxser_probe(struct pci_dev *pdev, goto err_rel3; for (i = 0; i < brd->info->nports; i++) - tty_register_device(mxvar_sdriver, brd->idx + i, &pdev->dev); + tty_port_register_device(&brd->ports[i].port, mxvar_sdriver, + brd->idx + i, &pdev->dev); pci_set_drvdata(pdev, brd); @@ -2695,7 +2723,8 @@ static int __init mxser_module_init(void) brd->idx = m * MXSER_PORTS_PER_BOARD; for (i = 0; i < brd->info->nports; i++) - tty_register_device(mxvar_sdriver, brd->idx + i, NULL); + tty_port_register_device(&brd->ports[i].port, + mxvar_sdriver, brd->idx + i, NULL); m++; } diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c index c43b683b6eb8..3e210a430fb3 100644 --- a/drivers/tty/n_gsm.c +++ b/drivers/tty/n_gsm.c @@ -108,7 +108,7 @@ struct gsm_mux_net { */ struct gsm_msg { - struct gsm_msg *next; + struct list_head list; u8 addr; /* DLCI address + flags */ u8 ctrl; /* Control byte + flags */ unsigned int len; /* Length of data block (can be zero) */ @@ -245,8 +245,7 @@ struct gsm_mux { unsigned int tx_bytes; /* TX data outstanding */ #define TX_THRESH_HI 8192 #define TX_THRESH_LO 2048 - struct gsm_msg *tx_head; /* Pending data packets */ - struct gsm_msg *tx_tail; + struct list_head tx_list; /* Pending data packets */ /* Control messages */ struct timer_list t2_timer; /* Retransmit timer for commands */ @@ -663,7 +662,7 @@ static struct gsm_msg *gsm_data_alloc(struct gsm_mux *gsm, u8 addr, int len, m->len = len; m->addr = addr; m->ctrl = ctrl; - m->next = NULL; + INIT_LIST_HEAD(&m->list); return m; } @@ -673,22 +672,21 @@ static struct gsm_msg *gsm_data_alloc(struct gsm_mux *gsm, u8 addr, int len, * * The tty device has called us to indicate that room has appeared in * the transmit queue. Ram more data into the pipe if we have any + * If we have been flow-stopped by a CMD_FCOFF, then we can only + * send messages on DLCI0 until CMD_FCON * * FIXME: lock against link layer control transmissions */ static void gsm_data_kick(struct gsm_mux *gsm) { - struct gsm_msg *msg = gsm->tx_head; + struct gsm_msg *msg, *nmsg; int len; int skip_sof = 0; - /* FIXME: We need to apply this solely to data messages */ - if (gsm->constipated) - return; - - while (gsm->tx_head != NULL) { - msg = gsm->tx_head; + list_for_each_entry_safe(msg, nmsg, &gsm->tx_list, list) { + if (gsm->constipated && msg->addr) + continue; if (gsm->encoding != 0) { gsm->txframe[0] = GSM1_SOF; len = gsm_stuff_frame(msg->data, @@ -711,14 +709,13 @@ static void gsm_data_kick(struct gsm_mux *gsm) len - skip_sof) < 0) break; /* FIXME: Can eliminate one SOF in many more cases */ - gsm->tx_head = msg->next; - if (gsm->tx_head == NULL) - gsm->tx_tail = NULL; gsm->tx_bytes -= msg->len; - kfree(msg); /* For a burst of frames skip the extra SOF within the burst */ skip_sof = 1; + + list_del(&msg->list); + kfree(msg); } } @@ -768,11 +765,7 @@ static void __gsm_data_queue(struct gsm_dlci *dlci, struct gsm_msg *msg) msg->data = dp; /* Add to the actual output queue */ - if (gsm->tx_tail) - gsm->tx_tail->next = msg; - else - gsm->tx_head = msg; - gsm->tx_tail = msg; + list_add_tail(&msg->list, &gsm->tx_list); gsm->tx_bytes += msg->len; gsm_data_kick(gsm); } @@ -875,7 +868,7 @@ static int gsm_dlci_data_output_framed(struct gsm_mux *gsm, /* dlci->skb is locked by tx_lock */ if (dlci->skb == NULL) { - dlci->skb = skb_dequeue(&dlci->skb_list); + dlci->skb = skb_dequeue_tail(&dlci->skb_list); if (dlci->skb == NULL) return 0; first = 1; @@ -886,7 +879,7 @@ static int gsm_dlci_data_output_framed(struct gsm_mux *gsm, if (len > gsm->mtu) { if (dlci->adaption == 3) { /* Over long frame, bin it */ - kfree_skb(dlci->skb); + dev_kfree_skb_any(dlci->skb); dlci->skb = NULL; return 0; } @@ -899,8 +892,11 @@ static int gsm_dlci_data_output_framed(struct gsm_mux *gsm, /* FIXME: need a timer or something to kick this so it can't get stuck with no work outstanding and no buffer free */ - if (msg == NULL) + if (msg == NULL) { + skb_queue_tail(&dlci->skb_list, dlci->skb); + dlci->skb = NULL; return -ENOMEM; + } dp = msg->data; if (dlci->adaption == 4) { /* Interruptible framed (Packetised Data) */ @@ -912,7 +908,7 @@ static int gsm_dlci_data_output_framed(struct gsm_mux *gsm, skb_pull(dlci->skb, len); __gsm_data_queue(dlci, msg); if (last) { - kfree_skb(dlci->skb); + dev_kfree_skb_any(dlci->skb); dlci->skb = NULL; } return size; @@ -971,16 +967,22 @@ static void gsm_dlci_data_sweep(struct gsm_mux *gsm) static void gsm_dlci_data_kick(struct gsm_dlci *dlci) { unsigned long flags; + int sweep; + + if (dlci->constipated) + return; spin_lock_irqsave(&dlci->gsm->tx_lock, flags); /* If we have nothing running then we need to fire up */ + sweep = (dlci->gsm->tx_bytes < TX_THRESH_LO); if (dlci->gsm->tx_bytes == 0) { if (dlci->net) gsm_dlci_data_output_framed(dlci->gsm, dlci); else gsm_dlci_data_output(dlci->gsm, dlci); - } else if (dlci->gsm->tx_bytes < TX_THRESH_LO) - gsm_dlci_data_sweep(dlci->gsm); + } + if (sweep) + gsm_dlci_data_sweep(dlci->gsm); spin_unlock_irqrestore(&dlci->gsm->tx_lock, flags); } @@ -1027,6 +1029,7 @@ static void gsm_process_modem(struct tty_struct *tty, struct gsm_dlci *dlci, { int mlines = 0; u8 brk = 0; + int fc; /* The modem status command can either contain one octet (v.24 signals) or two octets (v.24 signals + break signals). The length field will @@ -1038,19 +1041,21 @@ static void gsm_process_modem(struct tty_struct *tty, struct gsm_dlci *dlci, else { brk = modem & 0x7f; modem = (modem >> 7) & 0x7f; - }; + } /* Flow control/ready to communicate */ - if (modem & MDM_FC) { + fc = (modem & MDM_FC) || !(modem & MDM_RTR); + if (fc && !dlci->constipated) { /* Need to throttle our output on this device */ dlci->constipated = 1; - } - if (modem & MDM_RTC) { - mlines |= TIOCM_DSR | TIOCM_DTR; + } else if (!fc && dlci->constipated) { dlci->constipated = 0; gsm_dlci_data_kick(dlci); } + /* Map modem bits */ + if (modem & MDM_RTC) + mlines |= TIOCM_DSR | TIOCM_DTR; if (modem & MDM_RTR) mlines |= TIOCM_RTS | TIOCM_CTS; if (modem & MDM_IC) @@ -1061,7 +1066,7 @@ static void gsm_process_modem(struct tty_struct *tty, struct gsm_dlci *dlci, /* Carrier drop -> hangup */ if (tty) { if ((mlines & TIOCM_CD) == 0 && (dlci->modem_rx & TIOCM_CD)) - if (!(tty->termios->c_cflag & CLOCAL)) + if (!(tty->termios.c_cflag & CLOCAL)) tty_hangup(tty); if (brk & 0x01) tty_insert_flip_char(tty, 0, TTY_BREAK); @@ -1190,6 +1195,8 @@ static void gsm_control_message(struct gsm_mux *gsm, unsigned int command, u8 *data, int clen) { u8 buf[1]; + unsigned long flags; + switch (command) { case CMD_CLD: { struct gsm_dlci *dlci = gsm->dlci[0]; @@ -1206,16 +1213,18 @@ static void gsm_control_message(struct gsm_mux *gsm, unsigned int command, gsm_control_reply(gsm, CMD_TEST, data, clen); break; case CMD_FCON: - /* Modem wants us to STFU */ - gsm->constipated = 1; - gsm_control_reply(gsm, CMD_FCON, NULL, 0); - break; - case CMD_FCOFF: /* Modem can accept data again */ gsm->constipated = 0; - gsm_control_reply(gsm, CMD_FCOFF, NULL, 0); + gsm_control_reply(gsm, CMD_FCON, NULL, 0); /* Kick the link in case it is idling */ + spin_lock_irqsave(&gsm->tx_lock, flags); gsm_data_kick(gsm); + spin_unlock_irqrestore(&gsm->tx_lock, flags); + break; + case CMD_FCOFF: + /* Modem wants us to STFU */ + gsm->constipated = 1; + gsm_control_reply(gsm, CMD_FCOFF, NULL, 0); break; case CMD_MSC: /* Out of band modem line change indicator for a DLCI */ @@ -1668,7 +1677,7 @@ static void gsm_dlci_free(struct kref *ref) dlci->gsm->dlci[dlci->addr] = NULL; kfifo_free(dlci->fifo); while ((dlci->skb = skb_dequeue(&dlci->skb_list))) - kfree_skb(dlci->skb); + dev_kfree_skb(dlci->skb); kfree(dlci); } @@ -2007,7 +2016,7 @@ void gsm_cleanup_mux(struct gsm_mux *gsm) { int i; struct gsm_dlci *dlci = gsm->dlci[0]; - struct gsm_msg *txq; + struct gsm_msg *txq, *ntxq; struct gsm_control *gc; gsm->dead = 1; @@ -2042,11 +2051,9 @@ void gsm_cleanup_mux(struct gsm_mux *gsm) if (gsm->dlci[i]) gsm_dlci_release(gsm->dlci[i]); /* Now wipe the queues */ - for (txq = gsm->tx_head; txq != NULL; txq = gsm->tx_head) { - gsm->tx_head = txq->next; + list_for_each_entry_safe(txq, ntxq, &gsm->tx_list, list) kfree(txq); - } - gsm->tx_tail = NULL; + INIT_LIST_HEAD(&gsm->tx_list); } EXPORT_SYMBOL_GPL(gsm_cleanup_mux); @@ -2157,6 +2164,7 @@ struct gsm_mux *gsm_alloc_mux(void) } spin_lock_init(&gsm->lock); kref_init(&gsm->ref); + INIT_LIST_HEAD(&gsm->tx_list); gsm->t1 = T1; gsm->t2 = T2; @@ -2273,7 +2281,7 @@ static void gsmld_receive_buf(struct tty_struct *tty, const unsigned char *cp, gsm->error(gsm, *dp, flags); break; default: - WARN_ONCE("%s: unknown flag %d\n", + WARN_ONCE(1, "%s: unknown flag %d\n", tty_name(tty, buf), flags); break; } @@ -2377,12 +2385,12 @@ static void gsmld_write_wakeup(struct tty_struct *tty) /* Queue poll */ clear_bit(TTY_DO_WRITE_WAKEUP, &tty->flags); + spin_lock_irqsave(&gsm->tx_lock, flags); gsm_data_kick(gsm); if (gsm->tx_bytes < TX_THRESH_LO) { - spin_lock_irqsave(&gsm->tx_lock, flags); gsm_dlci_data_sweep(gsm); - spin_unlock_irqrestore(&gsm->tx_lock, flags); } + spin_unlock_irqrestore(&gsm->tx_lock, flags); } /** @@ -2868,14 +2876,14 @@ static const struct tty_port_operations gsm_port_ops = { .dtr_rts = gsm_dtr_rts, }; - -static int gsmtty_open(struct tty_struct *tty, struct file *filp) +static int gsmtty_install(struct tty_driver *driver, struct tty_struct *tty) { struct gsm_mux *gsm; struct gsm_dlci *dlci; - struct tty_port *port; unsigned int line = tty->index; unsigned int mux = line >> 6; + bool alloc = false; + int ret; line = line & 0x3F; @@ -2889,14 +2897,35 @@ static int gsmtty_open(struct tty_struct *tty, struct file *filp) gsm = gsm_mux[mux]; if (gsm->dead) return -EL2HLT; + /* If DLCI 0 is not yet fully open return an error. This is ok from a locking + perspective as we don't have to worry about this if DLCI0 is lost */ + if (gsm->dlci[0] && gsm->dlci[0]->state != DLCI_OPEN) + return -EL2NSYNC; dlci = gsm->dlci[line]; - if (dlci == NULL) + if (dlci == NULL) { + alloc = true; dlci = gsm_dlci_alloc(gsm, line); + } if (dlci == NULL) return -ENOMEM; - port = &dlci->port; - port->count++; + ret = tty_port_install(&dlci->port, driver, tty); + if (ret) { + if (alloc) + dlci_put(dlci); + return ret; + } + tty->driver_data = dlci; + + return 0; +} + +static int gsmtty_open(struct tty_struct *tty, struct file *filp) +{ + struct gsm_dlci *dlci = tty->driver_data; + struct tty_port *port = &dlci->port; + + port->count++; dlci_get(dlci); dlci_get(dlci->gsm->dlci[0]); mux_get(dlci->gsm); @@ -3043,13 +3072,13 @@ static void gsmtty_set_termios(struct tty_struct *tty, struct ktermios *old) the RPN control message. This however rapidly gets nasty as we then have to remap modem signals each way according to whether our virtual cable is null modem etc .. */ - tty_termios_copy_hw(tty->termios, old); + tty_termios_copy_hw(&tty->termios, old); } static void gsmtty_throttle(struct tty_struct *tty) { struct gsm_dlci *dlci = tty->driver_data; - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) dlci->modem_tx &= ~TIOCM_DTR; dlci->throttled = 1; /* Send an MSC with DTR cleared */ @@ -3059,7 +3088,7 @@ static void gsmtty_throttle(struct tty_struct *tty) static void gsmtty_unthrottle(struct tty_struct *tty) { struct gsm_dlci *dlci = tty->driver_data; - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) dlci->modem_tx |= TIOCM_DTR; dlci->throttled = 0; /* Send an MSC with DTR set */ @@ -3085,6 +3114,7 @@ static int gsmtty_break_ctl(struct tty_struct *tty, int state) /* Virtual ttys for the demux */ static const struct tty_operations gsmtty_ops = { + .install = gsmtty_install, .open = gsmtty_open, .close = gsmtty_close, .write = gsmtty_write, diff --git a/drivers/tty/n_r3964.c b/drivers/tty/n_r3964.c index 5c6c31459a2f..1e6405070ce6 100644 --- a/drivers/tty/n_r3964.c +++ b/drivers/tty/n_r3964.c @@ -1065,7 +1065,7 @@ static ssize_t r3964_read(struct tty_struct *tty, struct file *file, TRACE_L("read()"); - tty_lock(); + tty_lock(tty); pClient = findClient(pInfo, task_pid(current)); if (pClient) { @@ -1077,7 +1077,7 @@ static ssize_t r3964_read(struct tty_struct *tty, struct file *file, goto unlock; } /* block until there is a message: */ - wait_event_interruptible_tty(pInfo->read_wait, + wait_event_interruptible_tty(tty, pInfo->read_wait, (pMsg = remove_msg(pInfo, pClient))); } @@ -1107,7 +1107,7 @@ static ssize_t r3964_read(struct tty_struct *tty, struct file *file, } ret = -EPERM; unlock: - tty_unlock(); + tty_unlock(tty); return ret; } @@ -1156,7 +1156,7 @@ static ssize_t r3964_write(struct tty_struct *tty, struct file *file, pHeader->locks = 0; pHeader->owner = NULL; - tty_lock(); + tty_lock(tty); pClient = findClient(pInfo, task_pid(current)); if (pClient) { @@ -1175,7 +1175,7 @@ static ssize_t r3964_write(struct tty_struct *tty, struct file *file, add_tx_queue(pInfo, pHeader); trigger_transmit(pInfo); - tty_unlock(); + tty_unlock(tty); return 0; } diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c index ee1c268f5f9d..8c0b7b42319c 100644 --- a/drivers/tty/n_tty.c +++ b/drivers/tty/n_tty.c @@ -92,10 +92,18 @@ static inline int tty_put_user(struct tty_struct *tty, unsigned char x, static void n_tty_set_room(struct tty_struct *tty) { - /* tty->read_cnt is not read locked ? */ - int left = N_TTY_BUF_SIZE - tty->read_cnt - 1; + int left; int old_left; + /* tty->read_cnt is not read locked ? */ + if (I_PARMRK(tty)) { + /* Multiply read_cnt by 3, since each byte might take up to + * three times as many spaces when PARMRK is set (depending on + * its flags, e.g. parity error). */ + left = N_TTY_BUF_SIZE - tty->read_cnt * 3 - 1; + } else + left = N_TTY_BUF_SIZE - tty->read_cnt - 1; + /* * If we are doing input canonicalization, and there are no * pending newlines, let characters through without limit, so @@ -1432,6 +1440,12 @@ static void n_tty_receive_buf(struct tty_struct *tty, const unsigned char *cp, */ if (tty->receive_room < TTY_THRESHOLD_THROTTLE) tty_throttle(tty); + + /* FIXME: there is a tiny race here if the receive room check runs + before the other work executes and empties the buffer (upping + the receiving room and unthrottling. We then throttle and get + stuck. This has been observed and traced down by Vincent Pillet/ + We need to address this when we sort out out the rx path locking */ } int is_ignored(int sig) @@ -1460,7 +1474,7 @@ static void n_tty_set_termios(struct tty_struct *tty, struct ktermios *old) BUG_ON(!tty); if (old) - canon_change = (old->c_lflag ^ tty->termios->c_lflag) & ICANON; + canon_change = (old->c_lflag ^ tty->termios.c_lflag) & ICANON; if (canon_change) { memset(&tty->read_flags, 0, sizeof tty->read_flags); tty->canon_head = tty->read_tail; @@ -1728,7 +1742,8 @@ static ssize_t n_tty_read(struct tty_struct *tty, struct file *file, do_it_again: - BUG_ON(!tty->read_buf); + if (WARN_ON(!tty->read_buf)) + return -EAGAIN; c = job_control(tty, file); if (c < 0) @@ -1832,13 +1847,13 @@ do_it_again: if (tty->icanon && !L_EXTPROC(tty)) { /* N.B. avoid overrun if nr == 0 */ + spin_lock_irqsave(&tty->read_lock, flags); while (nr && tty->read_cnt) { int eol; eol = test_and_clear_bit(tty->read_tail, tty->read_flags); c = tty->read_buf[tty->read_tail]; - spin_lock_irqsave(&tty->read_lock, flags); tty->read_tail = ((tty->read_tail+1) & (N_TTY_BUF_SIZE-1)); tty->read_cnt--; @@ -1856,15 +1871,19 @@ do_it_again: if (tty_put_user(tty, c, b++)) { retval = -EFAULT; b--; + spin_lock_irqsave(&tty->read_lock, flags); break; } nr--; } if (eol) { tty_audit_push(tty); + spin_lock_irqsave(&tty->read_lock, flags); break; } + spin_lock_irqsave(&tty->read_lock, flags); } + spin_unlock_irqrestore(&tty->read_lock, flags); if (retval) break; } else { diff --git a/drivers/tty/nozomi.c b/drivers/tty/nozomi.c index e7592f9037da..b917c9424954 100644 --- a/drivers/tty/nozomi.c +++ b/drivers/tty/nozomi.c @@ -1473,8 +1473,8 @@ static int __devinit nozomi_card_init(struct pci_dev *pdev, port->dc = dc; tty_port_init(&port->port); port->port.ops = &noz_tty_port_ops; - tty_dev = tty_register_device(ntty_driver, dc->index_start + i, - &pdev->dev); + tty_dev = tty_port_register_device(&port->port, ntty_driver, + dc->index_start + i, &pdev->dev); if (IS_ERR(tty_dev)) { ret = PTR_ERR(tty_dev); diff --git a/drivers/tty/pty.c b/drivers/tty/pty.c index 5505ffc91da4..2bace847eb39 100644 --- a/drivers/tty/pty.c +++ b/drivers/tty/pty.c @@ -47,6 +47,7 @@ static void pty_close(struct tty_struct *tty, struct file *filp) wake_up_interruptible(&tty->read_wait); wake_up_interruptible(&tty->write_wait); tty->packet = 0; + /* Review - krefs on tty_link ?? */ if (!tty->link) return; tty->link->packet = 0; @@ -62,9 +63,9 @@ static void pty_close(struct tty_struct *tty, struct file *filp) mutex_unlock(&devpts_mutex); } #endif - tty_unlock(); + tty_unlock(tty); tty_vhangup(tty->link); - tty_lock(); + tty_lock(tty); } } @@ -231,8 +232,8 @@ out: static void pty_set_termios(struct tty_struct *tty, struct ktermios *old_termios) { - tty->termios->c_cflag &= ~(CSIZE | PARENB); - tty->termios->c_cflag |= (CS8 | CREAD); + tty->termios.c_cflag &= ~(CSIZE | PARENB); + tty->termios.c_cflag |= (CS8 | CREAD); } /** @@ -282,60 +283,110 @@ done: return 0; } -/* Traditional BSD devices */ -#ifdef CONFIG_LEGACY_PTYS - -static int pty_install(struct tty_driver *driver, struct tty_struct *tty) +/** + * pty_common_install - set up the pty pair + * @driver: the pty driver + * @tty: the tty being instantiated + * @bool: legacy, true if this is BSD style + * + * Perform the initial set up for the tty/pty pair. Called from the + * tty layer when the port is first opened. + * + * Locking: the caller must hold the tty_mutex + */ +static int pty_common_install(struct tty_driver *driver, struct tty_struct *tty, + bool legacy) { struct tty_struct *o_tty; + struct tty_port *ports[2]; int idx = tty->index; - int retval; + int retval = -ENOMEM; o_tty = alloc_tty_struct(); if (!o_tty) - return -ENOMEM; + goto err; + ports[0] = kmalloc(sizeof **ports, GFP_KERNEL); + ports[1] = kmalloc(sizeof **ports, GFP_KERNEL); + if (!ports[0] || !ports[1]) + goto err_free_tty; if (!try_module_get(driver->other->owner)) { /* This cannot in fact currently happen */ - retval = -ENOMEM; goto err_free_tty; } initialize_tty_struct(o_tty, driver->other, idx); - /* We always use new tty termios data so we can do this - the easy way .. */ - retval = tty_init_termios(tty); - if (retval) - goto err_deinit_tty; - - retval = tty_init_termios(o_tty); - if (retval) - goto err_free_termios; + if (legacy) { + /* We always use new tty termios data so we can do this + the easy way .. */ + retval = tty_init_termios(tty); + if (retval) + goto err_deinit_tty; + + retval = tty_init_termios(o_tty); + if (retval) + goto err_free_termios; + + driver->other->ttys[idx] = o_tty; + driver->ttys[idx] = tty; + } else { + memset(&tty->termios_locked, 0, sizeof(tty->termios_locked)); + tty->termios = driver->init_termios; + memset(&o_tty->termios_locked, 0, sizeof(tty->termios_locked)); + o_tty->termios = driver->other->init_termios; + } /* * Everything allocated ... set up the o_tty structure. */ - driver->other->ttys[idx] = o_tty; tty_driver_kref_get(driver->other); if (driver->subtype == PTY_TYPE_MASTER) o_tty->count++; /* Establish the links in both directions */ tty->link = o_tty; o_tty->link = tty; + tty_port_init(ports[0]); + tty_port_init(ports[1]); + o_tty->port = ports[0]; + tty->port = ports[1]; tty_driver_kref_get(driver); tty->count++; - driver->ttys[idx] = tty; return 0; err_free_termios: - tty_free_termios(tty); + if (legacy) + tty_free_termios(tty); err_deinit_tty: deinitialize_tty_struct(o_tty); module_put(o_tty->driver->owner); err_free_tty: + kfree(ports[0]); + kfree(ports[1]); free_tty_struct(o_tty); +err: return retval; } +static void pty_cleanup(struct tty_struct *tty) +{ + kfree(tty->port); +} + +/* Traditional BSD devices */ +#ifdef CONFIG_LEGACY_PTYS + +static int pty_install(struct tty_driver *driver, struct tty_struct *tty) +{ + return pty_common_install(driver, tty, true); +} + +static void pty_remove(struct tty_driver *driver, struct tty_struct *tty) +{ + struct tty_struct *pair = tty->link; + driver->ttys[tty->index] = NULL; + if (pair) + pair->driver->ttys[pair->index] = NULL; +} + static int pty_bsd_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { @@ -366,7 +417,9 @@ static const struct tty_operations master_pty_ops_bsd = { .unthrottle = pty_unthrottle, .set_termios = pty_set_termios, .ioctl = pty_bsd_ioctl, - .resize = pty_resize + .cleanup = pty_cleanup, + .resize = pty_resize, + .remove = pty_remove }; static const struct tty_operations slave_pty_ops_bsd = { @@ -379,7 +432,9 @@ static const struct tty_operations slave_pty_ops_bsd = { .chars_in_buffer = pty_chars_in_buffer, .unthrottle = pty_unthrottle, .set_termios = pty_set_termios, - .resize = pty_resize + .cleanup = pty_cleanup, + .resize = pty_resize, + .remove = pty_remove }; static void __init legacy_pty_init(void) @@ -389,12 +444,18 @@ static void __init legacy_pty_init(void) if (legacy_count <= 0) return; - pty_driver = alloc_tty_driver(legacy_count); - if (!pty_driver) + pty_driver = tty_alloc_driver(legacy_count, + TTY_DRIVER_RESET_TERMIOS | + TTY_DRIVER_REAL_RAW | + TTY_DRIVER_DYNAMIC_ALLOC); + if (IS_ERR(pty_driver)) panic("Couldn't allocate pty driver"); - pty_slave_driver = alloc_tty_driver(legacy_count); - if (!pty_slave_driver) + pty_slave_driver = tty_alloc_driver(legacy_count, + TTY_DRIVER_RESET_TERMIOS | + TTY_DRIVER_REAL_RAW | + TTY_DRIVER_DYNAMIC_ALLOC); + if (IS_ERR(pty_slave_driver)) panic("Couldn't allocate pty slave driver"); pty_driver->driver_name = "pty_master"; @@ -410,7 +471,6 @@ static void __init legacy_pty_init(void) pty_driver->init_termios.c_lflag = 0; pty_driver->init_termios.c_ispeed = 38400; pty_driver->init_termios.c_ospeed = 38400; - pty_driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_REAL_RAW; pty_driver->other = pty_slave_driver; tty_set_operations(pty_driver, &master_pty_ops_bsd); @@ -424,8 +484,6 @@ static void __init legacy_pty_init(void) pty_slave_driver->init_termios.c_cflag = B38400 | CS8 | CREAD; pty_slave_driver->init_termios.c_ispeed = 38400; pty_slave_driver->init_termios.c_ospeed = 38400; - pty_slave_driver->flags = TTY_DRIVER_RESET_TERMIOS | - TTY_DRIVER_REAL_RAW; pty_slave_driver->other = pty_driver; tty_set_operations(pty_slave_driver, &slave_pty_ops_bsd); @@ -497,78 +555,22 @@ static struct tty_struct *pts_unix98_lookup(struct tty_driver *driver, return tty; } -static void pty_unix98_shutdown(struct tty_struct *tty) -{ - tty_driver_remove_tty(tty->driver, tty); - /* We have our own method as we don't use the tty index */ - kfree(tty->termios); -} - /* We have no need to install and remove our tty objects as devpts does all the work for us */ static int pty_unix98_install(struct tty_driver *driver, struct tty_struct *tty) { - struct tty_struct *o_tty; - int idx = tty->index; - - o_tty = alloc_tty_struct(); - if (!o_tty) - return -ENOMEM; - if (!try_module_get(driver->other->owner)) { - /* This cannot in fact currently happen */ - goto err_free_tty; - } - initialize_tty_struct(o_tty, driver->other, idx); - - tty->termios = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL); - if (tty->termios == NULL) - goto err_free_mem; - *tty->termios = driver->init_termios; - tty->termios_locked = tty->termios + 1; - - o_tty->termios = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL); - if (o_tty->termios == NULL) - goto err_free_mem; - *o_tty->termios = driver->other->init_termios; - o_tty->termios_locked = o_tty->termios + 1; - - tty_driver_kref_get(driver->other); - if (driver->subtype == PTY_TYPE_MASTER) - o_tty->count++; - /* Establish the links in both directions */ - tty->link = o_tty; - o_tty->link = tty; - /* - * All structures have been allocated, so now we install them. - * Failures after this point use release_tty to clean up, so - * there's no need to null out the local pointers. - */ - tty_driver_kref_get(driver); - tty->count++; - return 0; -err_free_mem: - deinitialize_tty_struct(o_tty); - kfree(o_tty->termios); - kfree(tty->termios); - module_put(o_tty->driver->owner); -err_free_tty: - free_tty_struct(o_tty); - return -ENOMEM; -} - -static void ptm_unix98_remove(struct tty_driver *driver, struct tty_struct *tty) -{ + return pty_common_install(driver, tty, false); } -static void pts_unix98_remove(struct tty_driver *driver, struct tty_struct *tty) +static void pty_unix98_remove(struct tty_driver *driver, struct tty_struct *tty) { } static const struct tty_operations ptm_unix98_ops = { .lookup = ptm_unix98_lookup, .install = pty_unix98_install, - .remove = ptm_unix98_remove, + .remove = pty_unix98_remove, .open = pty_open, .close = pty_close, .write = pty_write, @@ -578,14 +580,14 @@ static const struct tty_operations ptm_unix98_ops = { .unthrottle = pty_unthrottle, .set_termios = pty_set_termios, .ioctl = pty_unix98_ioctl, - .shutdown = pty_unix98_shutdown, - .resize = pty_resize + .resize = pty_resize, + .cleanup = pty_cleanup }; static const struct tty_operations pty_unix98_ops = { .lookup = pts_unix98_lookup, .install = pty_unix98_install, - .remove = pts_unix98_remove, + .remove = pty_unix98_remove, .open = pty_open, .close = pty_close, .write = pty_write, @@ -594,7 +596,7 @@ static const struct tty_operations pty_unix98_ops = { .chars_in_buffer = pty_chars_in_buffer, .unthrottle = pty_unthrottle, .set_termios = pty_set_termios, - .shutdown = pty_unix98_shutdown + .cleanup = pty_cleanup, }; /** @@ -622,26 +624,27 @@ static int ptmx_open(struct inode *inode, struct file *filp) return retval; /* find a device that is not in use. */ - tty_lock(); + mutex_lock(&devpts_mutex); index = devpts_new_index(inode); - tty_unlock(); if (index < 0) { retval = index; goto err_file; } + mutex_unlock(&devpts_mutex); + mutex_lock(&tty_mutex); - mutex_lock(&devpts_mutex); tty = tty_init_dev(ptm_driver, index); - mutex_unlock(&devpts_mutex); - tty_lock(); - mutex_unlock(&tty_mutex); if (IS_ERR(tty)) { retval = PTR_ERR(tty); goto out; } + /* The tty returned here is locked so we can safely + drop the mutex */ + mutex_unlock(&tty_mutex); + set_bit(TTY_PTY_LOCK, &tty->flags); /* LOCK THE SLAVE */ tty_add_file(tty, filp); @@ -654,16 +657,17 @@ static int ptmx_open(struct inode *inode, struct file *filp) if (retval) goto err_release; - tty_unlock(); + tty_unlock(tty); return 0; err_release: - tty_unlock(); + tty_unlock(tty); tty_release(inode, filp); return retval; out: + mutex_unlock(&tty_mutex); devpts_kill_index(inode, index); - tty_unlock(); err_file: + mutex_unlock(&devpts_mutex); tty_free_file(filp); return retval; } @@ -672,11 +676,21 @@ static struct file_operations ptmx_fops; static void __init unix98_pty_init(void) { - ptm_driver = alloc_tty_driver(NR_UNIX98_PTY_MAX); - if (!ptm_driver) + ptm_driver = tty_alloc_driver(NR_UNIX98_PTY_MAX, + TTY_DRIVER_RESET_TERMIOS | + TTY_DRIVER_REAL_RAW | + TTY_DRIVER_DYNAMIC_DEV | + TTY_DRIVER_DEVPTS_MEM | + TTY_DRIVER_DYNAMIC_ALLOC); + if (IS_ERR(ptm_driver)) panic("Couldn't allocate Unix98 ptm driver"); - pts_driver = alloc_tty_driver(NR_UNIX98_PTY_MAX); - if (!pts_driver) + pts_driver = tty_alloc_driver(NR_UNIX98_PTY_MAX, + TTY_DRIVER_RESET_TERMIOS | + TTY_DRIVER_REAL_RAW | + TTY_DRIVER_DYNAMIC_DEV | + TTY_DRIVER_DEVPTS_MEM | + TTY_DRIVER_DYNAMIC_ALLOC); + if (IS_ERR(pts_driver)) panic("Couldn't allocate Unix98 pts driver"); ptm_driver->driver_name = "pty_master"; @@ -692,8 +706,6 @@ static void __init unix98_pty_init(void) ptm_driver->init_termios.c_lflag = 0; ptm_driver->init_termios.c_ispeed = 38400; ptm_driver->init_termios.c_ospeed = 38400; - ptm_driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_REAL_RAW | - TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_DEVPTS_MEM; ptm_driver->other = pts_driver; tty_set_operations(ptm_driver, &ptm_unix98_ops); @@ -707,8 +719,6 @@ static void __init unix98_pty_init(void) pts_driver->init_termios.c_cflag = B38400 | CS8 | CREAD; pts_driver->init_termios.c_ispeed = 38400; pts_driver->init_termios.c_ospeed = 38400; - pts_driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_REAL_RAW | - TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_DEVPTS_MEM; pts_driver->other = ptm_driver; tty_set_operations(pts_driver, &pty_unix98_ops); diff --git a/drivers/tty/rocket.c b/drivers/tty/rocket.c index 777d5f9cf6cc..9700d34b20a3 100644 --- a/drivers/tty/rocket.c +++ b/drivers/tty/rocket.c @@ -704,8 +704,8 @@ static void init_r_port(int board, int aiop, int chan, struct pci_dev *pci_dev) spin_lock_init(&info->slock); mutex_init(&info->write_mtx); rp_table[line] = info; - tty_register_device(rocket_driver, line, pci_dev ? &pci_dev->dev : - NULL); + tty_port_register_device(&info->port, rocket_driver, line, + pci_dev ? &pci_dev->dev : NULL); } /* @@ -720,7 +720,7 @@ static void configure_r_port(struct tty_struct *tty, struct r_port *info, unsigned rocketMode; int bits, baud, divisor; CHANNEL_t *cp; - struct ktermios *t = tty->termios; + struct ktermios *t = &tty->termios; cp = &info->channel; cflag = t->c_cflag; @@ -978,7 +978,7 @@ static int rp_open(struct tty_struct *tty, struct file *filp) tty->alt_speed = 460800; configure_r_port(tty, info, NULL); - if (tty->termios->c_cflag & CBAUD) { + if (tty->termios.c_cflag & CBAUD) { sSetDTR(cp); sSetRTS(cp); } @@ -1089,35 +1089,35 @@ static void rp_set_termios(struct tty_struct *tty, if (rocket_paranoia_check(info, "rp_set_termios")) return; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; /* * This driver doesn't support CS5 or CS6 */ if (((cflag & CSIZE) == CS5) || ((cflag & CSIZE) == CS6)) - tty->termios->c_cflag = + tty->termios.c_cflag = ((cflag & ~CSIZE) | (old_termios->c_cflag & CSIZE)); /* Or CMSPAR */ - tty->termios->c_cflag &= ~CMSPAR; + tty->termios.c_cflag &= ~CMSPAR; configure_r_port(tty, info, old_termios); cp = &info->channel; /* Handle transition to B0 status */ - if ((old_termios->c_cflag & CBAUD) && !(tty->termios->c_cflag & CBAUD)) { + if ((old_termios->c_cflag & CBAUD) && !(tty->termios.c_cflag & CBAUD)) { sClrDTR(cp); sClrRTS(cp); } /* Handle transition away from B0 status */ - if (!(old_termios->c_cflag & CBAUD) && (tty->termios->c_cflag & CBAUD)) { - if (!tty->hw_stopped || !(tty->termios->c_cflag & CRTSCTS)) + if (!(old_termios->c_cflag & CBAUD) && (tty->termios.c_cflag & CBAUD)) { + if (!tty->hw_stopped || !(tty->termios.c_cflag & CRTSCTS)) sSetRTS(cp); sSetDTR(cp); } - if ((old_termios->c_cflag & CRTSCTS) && !(tty->termios->c_cflag & CRTSCTS)) { + if ((old_termios->c_cflag & CRTSCTS) && !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; rp_start(tty); } diff --git a/drivers/tty/serial/68328serial.c b/drivers/tty/serial/68328serial.c index 3ed20e435e59..66c38a3f74ce 100644 --- a/drivers/tty/serial/68328serial.c +++ b/drivers/tty/serial/68328serial.c @@ -515,7 +515,7 @@ static void change_speed(struct m68k_serial *info, struct tty_struct *tty) unsigned cflag; int i; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; if (!(port = info->port)) return; @@ -617,7 +617,7 @@ static void rs_set_ldisc(struct tty_struct *tty) if (serial_paranoia_check(info, tty->name, "rs_set_ldisc")) return; - info->is_cons = (tty->termios->c_line == N_TTY); + info->is_cons = (tty->termios.c_line == N_TTY); printk("ttyS%d console mode %s\n", info->line, info->is_cons ? "on" : "off"); } @@ -985,7 +985,7 @@ static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) change_speed(info, tty); if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; rs_start(tty); } @@ -1070,7 +1070,7 @@ static void rs_close(struct tty_struct *tty, struct file * filp) if (tty->ldisc.close) (tty->ldisc.close)(tty); tty->ldisc = ldiscs[N_TTY]; - tty->termios->c_line = N_TTY; + tty->termios.c_line = N_TTY; if (tty->ldisc.open) (tty->ldisc.open)(tty); } @@ -1189,12 +1189,6 @@ rs68328_init(void) serial_driver->flags = TTY_DRIVER_REAL_RAW; tty_set_operations(serial_driver, &rs_ops); - if (tty_register_driver(serial_driver)) { - put_tty_driver(serial_driver); - printk(KERN_ERR "Couldn't register serial driver\n"); - return -ENOMEM; - } - local_irq_save(flags); for(i=0;i<NR_PORTS;i++) { @@ -1224,8 +1218,17 @@ rs68328_init(void) 0, "M68328_UART", info)) panic("Unable to attach 68328 serial interrupt\n"); + + tty_port_link_device(&info->tport, serial_driver, i); } local_irq_restore(flags); + + if (tty_register_driver(serial_driver)) { + put_tty_driver(serial_driver); + printk(KERN_ERR "Couldn't register serial driver\n"); + return -ENOMEM; + } + return 0; } diff --git a/drivers/tty/serial/8250/8250.c b/drivers/tty/serial/8250/8250.c index 8123f784bcda..44f52c6f15b9 100644 --- a/drivers/tty/serial/8250/8250.c +++ b/drivers/tty/serial/8250/8250.c @@ -2202,6 +2202,7 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, unsigned char cval, fcr = 0; unsigned long flags; unsigned int baud, quot; + int fifo_bug = 0; switch (termios->c_cflag & CSIZE) { case CS5: @@ -2221,8 +2222,11 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, if (termios->c_cflag & CSTOPB) cval |= UART_LCR_STOP; - if (termios->c_cflag & PARENB) + if (termios->c_cflag & PARENB) { cval |= UART_LCR_PARITY; + if (up->bugs & UART_BUG_PARITY) + fifo_bug = 1; + } if (!(termios->c_cflag & PARODD)) cval |= UART_LCR_EPAR; #ifdef CMSPAR @@ -2246,7 +2250,7 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) { fcr = uart_config[port->type].fcr; - if (baud < 2400) { + if (baud < 2400 || fifo_bug) { fcr &= ~UART_FCR_TRIGGER_MASK; fcr |= UART_FCR_TRIGGER_1; } @@ -2979,36 +2983,36 @@ void serial8250_resume_port(int line) static int __devinit serial8250_probe(struct platform_device *dev) { struct plat_serial8250_port *p = dev->dev.platform_data; - struct uart_port port; + struct uart_8250_port uart; int ret, i, irqflag = 0; - memset(&port, 0, sizeof(struct uart_port)); + memset(&uart, 0, sizeof(uart)); if (share_irqs) irqflag = IRQF_SHARED; for (i = 0; p && p->flags != 0; p++, i++) { - port.iobase = p->iobase; - port.membase = p->membase; - port.irq = p->irq; - port.irqflags = p->irqflags; - port.uartclk = p->uartclk; - port.regshift = p->regshift; - port.iotype = p->iotype; - port.flags = p->flags; - port.mapbase = p->mapbase; - port.hub6 = p->hub6; - port.private_data = p->private_data; - port.type = p->type; - port.serial_in = p->serial_in; - port.serial_out = p->serial_out; - port.handle_irq = p->handle_irq; - port.handle_break = p->handle_break; - port.set_termios = p->set_termios; - port.pm = p->pm; - port.dev = &dev->dev; - port.irqflags |= irqflag; - ret = serial8250_register_port(&port); + uart.port.iobase = p->iobase; + uart.port.membase = p->membase; + uart.port.irq = p->irq; + uart.port.irqflags = p->irqflags; + uart.port.uartclk = p->uartclk; + uart.port.regshift = p->regshift; + uart.port.iotype = p->iotype; + uart.port.flags = p->flags; + uart.port.mapbase = p->mapbase; + uart.port.hub6 = p->hub6; + uart.port.private_data = p->private_data; + uart.port.type = p->type; + uart.port.serial_in = p->serial_in; + uart.port.serial_out = p->serial_out; + uart.port.handle_irq = p->handle_irq; + uart.port.handle_break = p->handle_break; + uart.port.set_termios = p->set_termios; + uart.port.pm = p->pm; + uart.port.dev = &dev->dev; + uart.port.irqflags |= irqflag; + ret = serial8250_register_8250_port(&uart); if (ret < 0) { dev_err(&dev->dev, "unable to register port at index %d " "(IO%lx MEM%llx IRQ%d): %d\n", i, @@ -3081,7 +3085,7 @@ static struct platform_driver serial8250_isa_driver = { static struct platform_device *serial8250_isa_devs; /* - * serial8250_register_port and serial8250_unregister_port allows for + * serial8250_register_8250_port and serial8250_unregister_port allows for * 16x50 serial ports to be configured at run-time, to support PCMCIA * modems and PCI multiport cards. */ @@ -3155,6 +3159,7 @@ int serial8250_register_8250_port(struct uart_8250_port *up) uart->port.regshift = up->port.regshift; uart->port.iotype = up->port.iotype; uart->port.flags = up->port.flags | UPF_BOOT_AUTOCONF; + uart->bugs = up->bugs; uart->port.mapbase = up->port.mapbase; uart->port.private_data = up->port.private_data; if (up->port.dev) @@ -3198,29 +3203,6 @@ int serial8250_register_8250_port(struct uart_8250_port *up) EXPORT_SYMBOL(serial8250_register_8250_port); /** - * serial8250_register_port - register a serial port - * @port: serial port template - * - * Configure the serial port specified by the request. If the - * port exists and is in use, it is hung up and unregistered - * first. - * - * The port is then probed and if necessary the IRQ is autodetected - * If this fails an error is returned. - * - * On success the port is ready to use and the line number is returned. - */ -int serial8250_register_port(struct uart_port *port) -{ - struct uart_8250_port up; - - memset(&up, 0, sizeof(up)); - memcpy(&up.port, port, sizeof(*port)); - return serial8250_register_8250_port(&up); -} -EXPORT_SYMBOL(serial8250_register_port); - -/** * serial8250_unregister_port - remove a 16x50 serial port at runtime * @line: serial line number * diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h index f9719d167c8d..972b5212b58c 100644 --- a/drivers/tty/serial/8250/8250.h +++ b/drivers/tty/serial/8250/8250.h @@ -13,36 +13,6 @@ #include <linux/serial_8250.h> -struct uart_8250_port { - struct uart_port port; - struct timer_list timer; /* "no irq" timer */ - struct list_head list; /* ports on this IRQ */ - unsigned short capabilities; /* port capabilities */ - unsigned short bugs; /* port bugs */ - unsigned int tx_loadsz; /* transmit fifo load size */ - unsigned char acr; - unsigned char ier; - unsigned char lcr; - unsigned char mcr; - unsigned char mcr_mask; /* mask of user bits */ - unsigned char mcr_force; /* mask of forced bits */ - unsigned char cur_iotype; /* Running I/O type */ - - /* - * Some bits in registers are cleared on a read, so they must - * be saved whenever the register is read but the bits will not - * be immediately processed. - */ -#define LSR_SAVE_FLAGS UART_LSR_BRK_ERROR_BITS - unsigned char lsr_saved_flags; -#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA - unsigned char msr_saved_flags; - - /* 8250 specific callbacks */ - int (*dl_read)(struct uart_8250_port *); - void (*dl_write)(struct uart_8250_port *, int); -}; - struct old_serial_port { unsigned int uart; unsigned int baud_base; @@ -78,6 +48,7 @@ struct serial8250_config { #define UART_BUG_TXEN (1 << 1) /* UART has buggy TX IIR status */ #define UART_BUG_NOMSR (1 << 2) /* UART has buggy MSR status bits (Au1x00) */ #define UART_BUG_THRE (1 << 3) /* UART has buggy THRE reassertion */ +#define UART_BUG_PARITY (1 << 4) /* UART mishandles parity if FIFO enabled */ #define PROBE_RSA (1 << 0) #define PROBE_ANY (~0) diff --git a/drivers/tty/serial/8250/8250_acorn.c b/drivers/tty/serial/8250/8250_acorn.c index b0ce8c56f1a4..857498312a9a 100644 --- a/drivers/tty/serial/8250/8250_acorn.c +++ b/drivers/tty/serial/8250/8250_acorn.c @@ -43,7 +43,7 @@ serial_card_probe(struct expansion_card *ec, const struct ecard_id *id) { struct serial_card_info *info; struct serial_card_type *type = id->data; - struct uart_port port; + struct uart_8250_port uart; unsigned long bus_addr; unsigned int i; @@ -62,19 +62,19 @@ serial_card_probe(struct expansion_card *ec, const struct ecard_id *id) ecard_set_drvdata(ec, info); - memset(&port, 0, sizeof(struct uart_port)); - port.irq = ec->irq; - port.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ; - port.uartclk = type->uartclk; - port.iotype = UPIO_MEM; - port.regshift = 2; - port.dev = &ec->dev; + memset(&uart, 0, sizeof(struct uart_8250_port)); + uart.port.irq = ec->irq; + uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ; + uart.port.uartclk = type->uartclk; + uart.port.iotype = UPIO_MEM; + uart.port.regshift = 2; + uart.port.dev = &ec->dev; for (i = 0; i < info->num_ports; i ++) { - port.membase = info->vaddr + type->offset[i]; - port.mapbase = bus_addr + type->offset[i]; + uart.port.membase = info->vaddr + type->offset[i]; + uart.port.mapbase = bus_addr + type->offset[i]; - info->ports[i] = serial8250_register_port(&port); + info->ports[i] = serial8250_register_8250_port(&uart); } return 0; diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c index f574eef3075f..c3b2ec0c8c0b 100644 --- a/drivers/tty/serial/8250/8250_dw.c +++ b/drivers/tty/serial/8250/8250_dw.c @@ -89,7 +89,7 @@ static int dw8250_handle_irq(struct uart_port *p) static int __devinit dw8250_probe(struct platform_device *pdev) { - struct uart_port port = {}; + struct uart_8250_port uart = {}; struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); struct device_node *np = pdev->dev.of_node; @@ -104,28 +104,28 @@ static int __devinit dw8250_probe(struct platform_device *pdev) data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); if (!data) return -ENOMEM; - port.private_data = data; - - spin_lock_init(&port.lock); - port.mapbase = regs->start; - port.irq = irq->start; - port.handle_irq = dw8250_handle_irq; - port.type = PORT_8250; - port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP | + uart.port.private_data = data; + + spin_lock_init(&uart.port.lock); + uart.port.mapbase = regs->start; + uart.port.irq = irq->start; + uart.port.handle_irq = dw8250_handle_irq; + uart.port.type = PORT_8250; + uart.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP | UPF_FIXED_PORT | UPF_FIXED_TYPE; - port.dev = &pdev->dev; + uart.port.dev = &pdev->dev; - port.iotype = UPIO_MEM; - port.serial_in = dw8250_serial_in; - port.serial_out = dw8250_serial_out; + uart.port.iotype = UPIO_MEM; + uart.port.serial_in = dw8250_serial_in; + uart.port.serial_out = dw8250_serial_out; if (!of_property_read_u32(np, "reg-io-width", &val)) { switch (val) { case 1: break; case 4: - port.iotype = UPIO_MEM32; - port.serial_in = dw8250_serial_in32; - port.serial_out = dw8250_serial_out32; + uart.port.iotype = UPIO_MEM32; + uart.port.serial_in = dw8250_serial_in32; + uart.port.serial_out = dw8250_serial_out32; break; default: dev_err(&pdev->dev, "unsupported reg-io-width (%u)\n", @@ -135,15 +135,15 @@ static int __devinit dw8250_probe(struct platform_device *pdev) } if (!of_property_read_u32(np, "reg-shift", &val)) - port.regshift = val; + uart.port.regshift = val; if (of_property_read_u32(np, "clock-frequency", &val)) { dev_err(&pdev->dev, "no clock-frequency property set\n"); return -EINVAL; } - port.uartclk = val; + uart.port.uartclk = val; - data->line = serial8250_register_port(&port); + data->line = serial8250_register_8250_port(&uart); if (data->line < 0) return data->line; diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c index d8c0ffbfa6e3..097dff9c08ad 100644 --- a/drivers/tty/serial/8250/8250_gsc.c +++ b/drivers/tty/serial/8250/8250_gsc.c @@ -26,7 +26,7 @@ static int __init serial_init_chip(struct parisc_device *dev) { - struct uart_port port; + struct uart_8250_port uart; unsigned long address; int err; @@ -48,21 +48,21 @@ static int __init serial_init_chip(struct parisc_device *dev) if (dev->id.sversion != 0x8d) address += 0x800; - memset(&port, 0, sizeof(port)); - port.iotype = UPIO_MEM; + memset(&uart, 0, sizeof(uart)); + uart.port.iotype = UPIO_MEM; /* 7.272727MHz on Lasi. Assumed the same for Dino, Wax and Timi. */ - port.uartclk = 7272727; - port.mapbase = address; - port.membase = ioremap_nocache(address, 16); - port.irq = dev->irq; - port.flags = UPF_BOOT_AUTOCONF; - port.dev = &dev->dev; - - err = serial8250_register_port(&port); + uart.port.uartclk = 7272727; + uart.port.mapbase = address; + uart.port.membase = ioremap_nocache(address, 16); + uart.port.irq = dev->irq; + uart.port.flags = UPF_BOOT_AUTOCONF; + uart.port.dev = &dev->dev; + + err = serial8250_register_8250_port(&uart); if (err < 0) { printk(KERN_WARNING - "serial8250_register_port returned error %d\n", err); - iounmap(port.membase); + "serial8250_register_8250_port returned error %d\n", err); + iounmap(uart.port.membase); return err; } diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c index c13438c93012..8f1dd2cc00a8 100644 --- a/drivers/tty/serial/8250/8250_hp300.c +++ b/drivers/tty/serial/8250/8250_hp300.c @@ -171,7 +171,7 @@ static int __devinit hpdca_init_one(struct dio_dev *d, return 0; } #endif - memset(&port, 0, sizeof(struct uart_port)); + memset(&uart, 0, sizeof(uart)); /* Memory mapped I/O */ port.iotype = UPIO_MEM; @@ -182,7 +182,7 @@ static int __devinit hpdca_init_one(struct dio_dev *d, port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE); port.regshift = 1; port.dev = &d->dev; - line = serial8250_register_port(&port); + line = serial8250_register_8250_port(&uart); if (line < 0) { printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d" @@ -210,7 +210,7 @@ static int __init hp300_8250_init(void) #ifdef CONFIG_HPAPCI int line; unsigned long base; - struct uart_port uport; + struct uart_8250_port uart; struct hp300_port *port; int i; #endif @@ -248,26 +248,26 @@ static int __init hp300_8250_init(void) if (!port) return -ENOMEM; - memset(&uport, 0, sizeof(struct uart_port)); + memset(&uart, 0, sizeof(uart)); base = (FRODO_BASE + FRODO_APCI_OFFSET(i)); /* Memory mapped I/O */ - uport.iotype = UPIO_MEM; - uport.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \ + uart.port.iotype = UPIO_MEM; + uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \ | UPF_BOOT_AUTOCONF; /* XXX - no interrupt support yet */ - uport.irq = 0; - uport.uartclk = HPAPCI_BAUD_BASE * 16; - uport.mapbase = base; - uport.membase = (char *)(base + DIO_VIRADDRBASE); - uport.regshift = 2; + uart.port.irq = 0; + uart.port.uartclk = HPAPCI_BAUD_BASE * 16; + uart.port.mapbase = base; + uart.port.membase = (char *)(base + DIO_VIRADDRBASE); + uart.port.regshift = 2; - line = serial8250_register_port(&uport); + line = serial8250_register_8250_port(&uart); if (line < 0) { printk(KERN_NOTICE "8250_hp300: register_serial() APCI" - " %d irq %d failed\n", i, uport.irq); + " %d irq %d failed\n", i, uart.port.irq); kfree(port); continue; } diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 28e7c7cce893..ad4bb8dec36f 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -44,7 +44,7 @@ struct pci_serial_quirk { int (*init)(struct pci_dev *dev); int (*setup)(struct serial_private *, const struct pciserial_board *, - struct uart_port *, int); + struct uart_8250_port *, int); void (*exit)(struct pci_dev *dev); }; @@ -59,7 +59,7 @@ struct serial_private { }; static int pci_default_setup(struct serial_private*, - const struct pciserial_board*, struct uart_port*, int); + const struct pciserial_board*, struct uart_8250_port *, int); static void moan_device(const char *str, struct pci_dev *dev) { @@ -74,7 +74,7 @@ static void moan_device(const char *str, struct pci_dev *dev) } static int -setup_port(struct serial_private *priv, struct uart_port *port, +setup_port(struct serial_private *priv, struct uart_8250_port *port, int bar, int offset, int regshift) { struct pci_dev *dev = priv->dev; @@ -93,17 +93,17 @@ setup_port(struct serial_private *priv, struct uart_port *port, if (!priv->remapped_bar[bar]) return -ENOMEM; - port->iotype = UPIO_MEM; - port->iobase = 0; - port->mapbase = base + offset; - port->membase = priv->remapped_bar[bar] + offset; - port->regshift = regshift; + port->port.iotype = UPIO_MEM; + port->port.iobase = 0; + port->port.mapbase = base + offset; + port->port.membase = priv->remapped_bar[bar] + offset; + port->port.regshift = regshift; } else { - port->iotype = UPIO_PORT; - port->iobase = base + offset; - port->mapbase = 0; - port->membase = NULL; - port->regshift = 0; + port->port.iotype = UPIO_PORT; + port->port.iobase = base + offset; + port->port.mapbase = 0; + port->port.membase = NULL; + port->port.regshift = 0; } return 0; } @@ -113,7 +113,7 @@ setup_port(struct serial_private *priv, struct uart_port *port, */ static int addidata_apci7800_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { unsigned int bar = 0, offset = board->first_offset; bar = FL_GET_BASE(board->flags); @@ -140,7 +140,7 @@ static int addidata_apci7800_setup(struct serial_private *priv, */ static int afavlab_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { unsigned int bar, offset = board->first_offset; @@ -195,7 +195,7 @@ static int pci_hp_diva_init(struct pci_dev *dev) static int pci_hp_diva_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { unsigned int offset = board->first_offset; unsigned int bar = FL_GET_BASE(board->flags); @@ -370,7 +370,7 @@ static void __devexit pci_ni8430_exit(struct pci_dev *dev) /* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */ static int sbs_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { unsigned int bar, offset = board->first_offset; @@ -525,7 +525,7 @@ static int pci_siig_init(struct pci_dev *dev) static int pci_siig_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { unsigned int bar = FL_GET_BASE(board->flags) + idx, offset = 0; @@ -619,7 +619,7 @@ static int pci_timedia_init(struct pci_dev *dev) static int pci_timedia_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { unsigned int bar = 0, offset = board->first_offset; @@ -653,7 +653,7 @@ pci_timedia_setup(struct serial_private *priv, static int titan_400l_800l_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { unsigned int bar, offset = board->first_offset; @@ -754,7 +754,7 @@ static int pci_ni8430_init(struct pci_dev *dev) static int pci_ni8430_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { void __iomem *p; unsigned long base, len; @@ -781,7 +781,7 @@ pci_ni8430_setup(struct serial_private *priv, static int pci_netmos_9900_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { unsigned int bar; @@ -1032,10 +1032,17 @@ static int pci_oxsemi_tornado_init(struct pci_dev *dev) return number_uarts; } -static int -pci_default_setup(struct serial_private *priv, +static int pci_asix_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) +{ + port->bugs |= UART_BUG_PARITY; + return pci_default_setup(priv, board, port, idx); +} + +static int pci_default_setup(struct serial_private *priv, + const struct pciserial_board *board, + struct uart_8250_port *port, int idx) { unsigned int bar, offset = board->first_offset, maxnr; @@ -1057,15 +1064,15 @@ pci_default_setup(struct serial_private *priv, static int ce4100_serial_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { int ret; ret = setup_port(priv, port, 0, 0, board->reg_shift); - port->iotype = UPIO_MEM32; - port->type = PORT_XSCALE; - port->flags = (port->flags | UPF_FIXED_PORT | UPF_FIXED_TYPE); - port->regshift = 2; + port->port.iotype = UPIO_MEM32; + port->port.type = PORT_XSCALE; + port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE); + port->port.regshift = 2; return ret; } @@ -1073,16 +1080,16 @@ ce4100_serial_setup(struct serial_private *priv, static int pci_omegapci_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { return setup_port(priv, port, 2, idx * 8, 0); } static int skip_tx_en_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { - port->flags |= UPF_NO_TXEN_TEST; + port->port.flags |= UPF_NO_TXEN_TEST; printk(KERN_DEBUG "serial8250: skipping TxEn test for device " "[%04x:%04x] subsystem [%04x:%04x]\n", priv->dev->vendor, @@ -1131,11 +1138,11 @@ static unsigned int kt_serial_in(struct uart_port *p, int offset) static int kt_serial_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { - port->flags |= UPF_BUG_THRE; - port->serial_in = kt_serial_in; - port->handle_break = kt_handle_break; + port->port.flags |= UPF_BUG_THRE; + port->port.serial_in = kt_serial_in; + port->port.handle_break = kt_handle_break; return skip_tx_en_setup(priv, board, port, idx); } @@ -1151,9 +1158,9 @@ static int pci_eg20t_init(struct pci_dev *dev) static int pci_xr17c154_setup(struct serial_private *priv, const struct pciserial_board *board, - struct uart_port *port, int idx) + struct uart_8250_port *port, int idx) { - port->flags |= UPF_EXAR_EFR; + port->port.flags |= UPF_EXAR_EFR; return pci_default_setup(priv, board, port, idx); } @@ -1187,6 +1194,9 @@ pci_xr17c154_setup(struct serial_private *priv, #define PCIE_DEVICE_ID_NEO_2_OX_IBM 0x00F6 #define PCI_DEVICE_ID_PLX_CRONYX_OMEGA 0xc001 #define PCI_DEVICE_ID_INTEL_PATSBURG_KT 0x1d3d +#define PCI_VENDOR_ID_AGESTAR 0x5372 +#define PCI_DEVICE_ID_AGESTAR_9375 0x6872 +#define PCI_VENDOR_ID_ASIX 0x9710 /* Unknown vendors/cards - this should not be in linux/pci_ids.h */ #define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584 @@ -1726,7 +1736,17 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, .setup = pci_omegapci_setup, - }, + }, + /* + * ASIX devices with FIFO bug + */ + { + .vendor = PCI_VENDOR_ID_ASIX, + .device = PCI_ANY_ID, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_asix_setup, + }, /* * Default "match everything" terminator entry */ @@ -1887,7 +1907,6 @@ enum pci_board_num_t { pbn_panacom, pbn_panacom2, pbn_panacom4, - pbn_exsys_4055, pbn_plx_romulus, pbn_oxsemi, pbn_oxsemi_1_4000000, @@ -2393,13 +2412,6 @@ static struct pciserial_board pci_boards[] __devinitdata = { .reg_shift = 7, }, - [pbn_exsys_4055] = { - .flags = FL_BASE2, - .num_ports = 4, - .base_baud = 115200, - .uart_offset = 8, - }, - /* I think this entry is broken - the first_offset looks wrong --rmk */ [pbn_plx_romulus] = { .flags = FL_BASE2, @@ -2728,7 +2740,7 @@ serial_pci_matches(const struct pciserial_board *board, struct serial_private * pciserial_init_ports(struct pci_dev *dev, const struct pciserial_board *board) { - struct uart_port serial_port; + struct uart_8250_port uart; struct serial_private *priv; struct pci_serial_quirk *quirk; int rc, nr_ports, i; @@ -2768,22 +2780,22 @@ pciserial_init_ports(struct pci_dev *dev, const struct pciserial_board *board) priv->dev = dev; priv->quirk = quirk; - memset(&serial_port, 0, sizeof(struct uart_port)); - serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ; - serial_port.uartclk = board->base_baud * 16; - serial_port.irq = get_pci_irq(dev, board); - serial_port.dev = &dev->dev; + memset(&uart, 0, sizeof(uart)); + uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ; + uart.port.uartclk = board->base_baud * 16; + uart.port.irq = get_pci_irq(dev, board); + uart.port.dev = &dev->dev; for (i = 0; i < nr_ports; i++) { - if (quirk->setup(priv, board, &serial_port, i)) + if (quirk->setup(priv, board, &uart, i)) break; #ifdef SERIAL_DEBUG_PCI printk(KERN_DEBUG "Setup PCI port: port %lx, irq %d, type %d\n", - serial_port.iobase, serial_port.irq, serial_port.iotype); + uart.port.iobase, uart.port.irq, uart.port.iotype); #endif - priv->line[i] = serial8250_register_port(&serial_port); + priv->line[i] = serial8250_register_8250_port(&uart); if (priv->line[i] < 0) { printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), priv->line[i]); break; @@ -3193,7 +3205,7 @@ static struct pci_device_id serial_pci_tbl[] = { { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, PCI_SUBVENDOR_ID_EXSYS, PCI_SUBDEVICE_ID_EXSYS_4055, 0, 0, - pbn_exsys_4055 }, + pbn_b2_4_115200 }, /* * Megawolf Romulus PCI Serial Card, from Mike Hudson * (Exoray@isys.ca) @@ -4179,6 +4191,12 @@ static struct pci_device_id serial_pci_tbl[] = { pbn_omegapci }, /* + * AgeStar as-prs2-009 + */ + { PCI_VENDOR_ID_AGESTAR, PCI_DEVICE_ID_AGESTAR_9375, + PCI_ANY_ID, PCI_ANY_ID, + 0, 0, pbn_b0_bt_2_115200 }, + /* * These entries match devices with class COMMUNICATION_SERIAL, * COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL */ diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c index a2f236510ff1..fde5aa60d51e 100644 --- a/drivers/tty/serial/8250/8250_pnp.c +++ b/drivers/tty/serial/8250/8250_pnp.c @@ -424,7 +424,7 @@ static int __devinit serial_pnp_guess_board(struct pnp_dev *dev, int *flags) static int __devinit serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) { - struct uart_port port; + struct uart_8250_port uart; int ret, line, flags = dev_id->driver_data; if (flags & UNKNOWN_DEV) { @@ -433,32 +433,32 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) return ret; } - memset(&port, 0, sizeof(struct uart_port)); + memset(&uart, 0, sizeof(uart)); if (pnp_irq_valid(dev, 0)) - port.irq = pnp_irq(dev, 0); + uart.port.irq = pnp_irq(dev, 0); if (pnp_port_valid(dev, 0)) { - port.iobase = pnp_port_start(dev, 0); - port.iotype = UPIO_PORT; + uart.port.iobase = pnp_port_start(dev, 0); + uart.port.iotype = UPIO_PORT; } else if (pnp_mem_valid(dev, 0)) { - port.mapbase = pnp_mem_start(dev, 0); - port.iotype = UPIO_MEM; - port.flags = UPF_IOREMAP; + uart.port.mapbase = pnp_mem_start(dev, 0); + uart.port.iotype = UPIO_MEM; + uart.port.flags = UPF_IOREMAP; } else return -ENODEV; #ifdef SERIAL_DEBUG_PNP printk(KERN_DEBUG "Setup PNP port: port %x, mem 0x%lx, irq %d, type %d\n", - port.iobase, port.mapbase, port.irq, port.iotype); + uart.port.iobase, uart.port.mapbase, uart.port.irq, uart.port.iotype); #endif - port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF; + uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF; if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE) - port.flags |= UPF_SHARE_IRQ; - port.uartclk = 1843200; - port.dev = &dev->dev; + uart.port.flags |= UPF_SHARE_IRQ; + uart.port.uartclk = 1843200; + uart.port.dev = &dev->dev; - line = serial8250_register_port(&port); + line = serial8250_register_8250_port(&uart); if (line < 0) return -ENODEV; diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c index 29b695d041ec..b7d48b346393 100644 --- a/drivers/tty/serial/8250/serial_cs.c +++ b/drivers/tty/serial/8250/serial_cs.c @@ -73,7 +73,7 @@ struct serial_quirk { unsigned int prodid; int multi; /* 1 = multifunction, > 1 = # ports */ void (*config)(struct pcmcia_device *); - void (*setup)(struct pcmcia_device *, struct uart_port *); + void (*setup)(struct pcmcia_device *, struct uart_8250_port *); void (*wakeup)(struct pcmcia_device *); int (*post)(struct pcmcia_device *); }; @@ -105,9 +105,9 @@ struct serial_cfg_mem { * Elan VPU16551 UART with 14.7456MHz oscillator * manfid 0x015D, 0x4C45 */ -static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_port *port) +static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_8250_port *uart) { - port->uartclk = 14745600; + uart->port.uartclk = 14745600; } static int quirk_post_ibm(struct pcmcia_device *link) @@ -343,25 +343,25 @@ static void serial_detach(struct pcmcia_device *link) static int setup_serial(struct pcmcia_device *handle, struct serial_info * info, unsigned int iobase, int irq) { - struct uart_port port; + struct uart_8250_port uart; int line; - memset(&port, 0, sizeof (struct uart_port)); - port.iobase = iobase; - port.irq = irq; - port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ; - port.uartclk = 1843200; - port.dev = &handle->dev; + memset(&uart, 0, sizeof(uart)); + uart.port.iobase = iobase; + uart.port.irq = irq; + uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ; + uart.port.uartclk = 1843200; + uart.port.dev = &handle->dev; if (buggy_uart) - port.flags |= UPF_BUGGY_UART; + uart.port.flags |= UPF_BUGGY_UART; if (info->quirk && info->quirk->setup) - info->quirk->setup(handle, &port); + info->quirk->setup(handle, &uart); - line = serial8250_register_port(&port); + line = serial8250_register_8250_port(&uart); if (line < 0) { - printk(KERN_NOTICE "serial_cs: serial8250_register_port() at " - "0x%04lx, irq %d failed\n", (u_long)iobase, irq); + pr_err("serial_cs: serial8250_register_8250_port() at 0x%04lx, irq %d failed\n", + (unsigned long)iobase, irq); return -EINVAL; } diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 4720b4ba096a..04b9e13045d7 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -257,12 +257,19 @@ config SERIAL_MAX3100 help MAX3100 chip support -config SERIAL_MAX3107 - tristate "MAX3107 support" +config SERIAL_MAX310X + bool "MAX310X support" depends on SPI select SERIAL_CORE + select REGMAP_SPI if SPI + default n help - MAX3107 chip support + This selects support for an advanced UART from Maxim (Dallas). + Supported ICs are MAX3107, MAX3108. + Each IC contains 128 words each of receive and transmit FIFO + that can be controlled through I2C or high-speed SPI. + + Say Y here if you want to support this ICs. config SERIAL_DZ bool "DECstation DZ serial driver" @@ -704,6 +711,25 @@ config SERIAL_PNX8XXX_CONSOLE If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330 and you want to use serial console, say Y. Otherwise, say N. +config SERIAL_HS_LPC32XX + tristate "LPC32XX high speed serial port support" + depends on ARCH_LPC32XX && OF + select SERIAL_CORE + help + Support for the LPC32XX high speed serial ports (up to 900kbps). + Those are UARTs completely different from the Standard UARTs on the + LPC32XX SoC. + Choose M or Y here to build this driver. + +config SERIAL_HS_LPC32XX_CONSOLE + bool "Enable LPC32XX high speed UART serial console" + depends on SERIAL_HS_LPC32XX + select SERIAL_CORE_CONSOLE + help + If you would like to be able to use one of the high speed serial + ports on the LPC32XX as the console, you can do so by answering + Y to this option. + config SERIAL_CORE tristate diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index 7257c5d898ae..2af9e5279dab 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -28,12 +28,13 @@ obj-$(CONFIG_SERIAL_BFIN) += bfin_uart.o obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o obj-$(CONFIG_SERIAL_MAX3100) += max3100.o -obj-$(CONFIG_SERIAL_MAX3107) += max3107.o +obj-$(CONFIG_SERIAL_MAX310X) += max310x.o obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o obj-$(CONFIG_SERIAL_MUX) += mux.o obj-$(CONFIG_SERIAL_68328) += 68328serial.o obj-$(CONFIG_SERIAL_MCF) += mcf.o obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o +obj-$(CONFIG_SERIAL_HS_LPC32XX) += lpc32xx_hs.o obj-$(CONFIG_SERIAL_DZ) += dz.o obj-$(CONFIG_SERIAL_ZS) += zs.o obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index d3553b5d3fca..92b1ac8db63d 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -1215,14 +1215,14 @@ static irqreturn_t pl011_int(int irq, void *dev_id) return IRQ_RETVAL(handled); } -static unsigned int pl01x_tx_empty(struct uart_port *port) +static unsigned int pl011_tx_empty(struct uart_port *port) { struct uart_amba_port *uap = (struct uart_amba_port *)port; unsigned int status = readw(uap->port.membase + UART01x_FR); return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT; } -static unsigned int pl01x_get_mctrl(struct uart_port *port) +static unsigned int pl011_get_mctrl(struct uart_port *port) { struct uart_amba_port *uap = (struct uart_amba_port *)port; unsigned int result = 0; @@ -1285,7 +1285,7 @@ static void pl011_break_ctl(struct uart_port *port, int break_state) } #ifdef CONFIG_CONSOLE_POLL -static int pl010_get_poll_char(struct uart_port *port) +static int pl011_get_poll_char(struct uart_port *port) { struct uart_amba_port *uap = (struct uart_amba_port *)port; unsigned int status; @@ -1297,7 +1297,7 @@ static int pl010_get_poll_char(struct uart_port *port) return readw(uap->port.membase + UART01x_DR); } -static void pl010_put_poll_char(struct uart_port *port, +static void pl011_put_poll_char(struct uart_port *port, unsigned char ch) { struct uart_amba_port *uap = (struct uart_amba_port *)port; @@ -1637,7 +1637,7 @@ static const char *pl011_type(struct uart_port *port) /* * Release the memory region(s) being used by 'port' */ -static void pl010_release_port(struct uart_port *port) +static void pl011_release_port(struct uart_port *port) { release_mem_region(port->mapbase, SZ_4K); } @@ -1645,7 +1645,7 @@ static void pl010_release_port(struct uart_port *port) /* * Request the memory region(s) being used by 'port' */ -static int pl010_request_port(struct uart_port *port) +static int pl011_request_port(struct uart_port *port) { return request_mem_region(port->mapbase, SZ_4K, "uart-pl011") != NULL ? 0 : -EBUSY; @@ -1654,18 +1654,18 @@ static int pl010_request_port(struct uart_port *port) /* * Configure/autoconfigure the port. */ -static void pl010_config_port(struct uart_port *port, int flags) +static void pl011_config_port(struct uart_port *port, int flags) { if (flags & UART_CONFIG_TYPE) { port->type = PORT_AMBA; - pl010_request_port(port); + pl011_request_port(port); } } /* * verify the new serial_struct (for TIOCSSERIAL). */ -static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser) +static int pl011_verify_port(struct uart_port *port, struct serial_struct *ser) { int ret = 0; if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA) @@ -1678,9 +1678,9 @@ static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser) } static struct uart_ops amba_pl011_pops = { - .tx_empty = pl01x_tx_empty, + .tx_empty = pl011_tx_empty, .set_mctrl = pl011_set_mctrl, - .get_mctrl = pl01x_get_mctrl, + .get_mctrl = pl011_get_mctrl, .stop_tx = pl011_stop_tx, .start_tx = pl011_start_tx, .stop_rx = pl011_stop_rx, @@ -1691,13 +1691,13 @@ static struct uart_ops amba_pl011_pops = { .flush_buffer = pl011_dma_flush_buffer, .set_termios = pl011_set_termios, .type = pl011_type, - .release_port = pl010_release_port, - .request_port = pl010_request_port, - .config_port = pl010_config_port, - .verify_port = pl010_verify_port, + .release_port = pl011_release_port, + .request_port = pl011_request_port, + .config_port = pl011_config_port, + .verify_port = pl011_verify_port, #ifdef CONFIG_CONSOLE_POLL - .poll_get_char = pl010_get_poll_char, - .poll_put_char = pl010_put_poll_char, + .poll_get_char = pl011_get_poll_char, + .poll_put_char = pl011_put_poll_char, #endif }; diff --git a/drivers/tty/serial/bfin_uart.c b/drivers/tty/serial/bfin_uart.c index bd97db23985b..9242d56ba267 100644 --- a/drivers/tty/serial/bfin_uart.c +++ b/drivers/tty/serial/bfin_uart.c @@ -182,7 +182,7 @@ static void bfin_serial_start_tx(struct uart_port *port) * To avoid losting RX interrupt, we reset IR function * before sending data. */ - if (tty->termios->c_line == N_IRDA) + if (tty->termios.c_line == N_IRDA) bfin_serial_reset_irda(port); #ifdef CONFIG_SERIAL_BFIN_DMA diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c index 80b6b1b1f725..35ee6a2c6877 100644 --- a/drivers/tty/serial/crisv10.c +++ b/drivers/tty/serial/crisv10.c @@ -955,7 +955,7 @@ static const struct control_pins e100_modem_pins[NR_PORTS] = /* Calculate the chartime depending on baudrate, numbor of bits etc. */ static void update_char_time(struct e100_serial * info) { - tcflag_t cflags = info->port.tty->termios->c_cflag; + tcflag_t cflags = info->port.tty->termios.c_cflag; int bits; /* calc. number of bits / data byte */ @@ -1473,7 +1473,7 @@ rs_stop(struct tty_struct *tty) xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty)); xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, stop); - if (tty->termios->c_iflag & IXON ) { + if (tty->termios.c_iflag & IXON ) { xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); } @@ -1496,7 +1496,7 @@ rs_start(struct tty_struct *tty) info->xmit.tail,SERIAL_XMIT_SIZE))); xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(tty)); xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable); - if (tty->termios->c_iflag & IXON ) { + if (tty->termios.c_iflag & IXON ) { xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); } @@ -2929,7 +2929,7 @@ shutdown(struct e100_serial * info) descr[i].buf = 0; } - if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) { + if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) { /* hang up DTR and RTS if HUPCL is enabled */ e100_dtr(info, 0); e100_rts(info, 0); /* could check CRTSCTS before doing this */ @@ -2953,12 +2953,12 @@ change_speed(struct e100_serial *info) unsigned long flags; /* first some safety checks */ - if (!info->port.tty || !info->port.tty->termios) + if (!info->port.tty) return; if (!info->ioport) return; - cflag = info->port.tty->termios->c_cflag; + cflag = info->port.tty->termios.c_cflag; /* possibly, the tx/rx should be disabled first to do this safely */ @@ -3088,7 +3088,7 @@ change_speed(struct e100_serial *info) info->ioport[REG_REC_CTRL] = info->rx_ctrl; xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty)); xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable); - if (info->port.tty->termios->c_iflag & IXON ) { + if (info->port.tty->termios.c_iflag & IXON ) { DFLOW(DEBUG_LOG(info->line, "FLOW XOFF enabled 0x%02X\n", STOP_CHAR(info->port.tty))); xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); @@ -3355,7 +3355,7 @@ rs_throttle(struct tty_struct * tty) DFLOW(DEBUG_LOG(info->line,"rs_throttle %lu\n", tty->ldisc.chars_in_buffer(tty))); /* Do RTS before XOFF since XOFF might take some time */ - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { /* Turn off RTS line */ e100_rts(info, 0); } @@ -3377,7 +3377,7 @@ rs_unthrottle(struct tty_struct * tty) DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc %d\n", tty->ldisc.chars_in_buffer(tty))); DFLOW(DEBUG_LOG(info->line,"rs_unthrottle flip.count: %i\n", tty->flip.count)); /* Do RTS before XOFF since XOFF might take some time */ - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { /* Assert RTS line */ e100_rts(info, 1); } @@ -3748,7 +3748,7 @@ rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) /* Handle turning off CRTSCTS */ if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; rs_start(tty); } @@ -3815,7 +3815,7 @@ rs_close(struct tty_struct *tty, struct file * filp) * separate termios for callout and dialin. */ if (info->flags & ASYNC_NORMAL_ACTIVE) - info->normal_termios = *tty->termios; + info->normal_termios = tty->termios; /* * Now we wait for the transmit buffer to clear; and we notify * the line discipline to only process XON/XOFF characters. @@ -3976,7 +3976,7 @@ block_til_ready(struct tty_struct *tty, struct file * filp, */ if (tty_hung_up_p(filp) || (info->flags & ASYNC_CLOSING)) { - wait_event_interruptible_tty(info->close_wait, + wait_event_interruptible_tty(tty, info->close_wait, !(info->flags & ASYNC_CLOSING)); #ifdef SERIAL_DO_RESTART if (info->flags & ASYNC_HUP_NOTIFY) @@ -3998,7 +3998,7 @@ block_til_ready(struct tty_struct *tty, struct file * filp, return 0; } - if (tty->termios->c_cflag & CLOCAL) { + if (tty->termios.c_cflag & CLOCAL) { do_clocal = 1; } @@ -4052,9 +4052,9 @@ block_til_ready(struct tty_struct *tty, struct file * filp, printk("block_til_ready blocking: ttyS%d, count = %d\n", info->line, info->count); #endif - tty_unlock(); + tty_unlock(tty); schedule(); - tty_lock(); + tty_lock(tty); } set_current_state(TASK_RUNNING); remove_wait_queue(&info->open_wait, &wait); @@ -4115,7 +4115,7 @@ rs_open(struct tty_struct *tty, struct file * filp) */ if (tty_hung_up_p(filp) || (info->flags & ASYNC_CLOSING)) { - wait_event_interruptible_tty(info->close_wait, + wait_event_interruptible_tty(tty, info->close_wait, !(info->flags & ASYNC_CLOSING)); #ifdef SERIAL_DO_RESTART return ((info->flags & ASYNC_HUP_NOTIFY) ? @@ -4219,7 +4219,7 @@ rs_open(struct tty_struct *tty, struct file * filp) } if ((info->count == 1) && (info->flags & ASYNC_SPLIT_TERMIOS)) { - *tty->termios = info->normal_termios; + tty->termios = info->normal_termios; change_speed(info); } @@ -4443,14 +4443,12 @@ static int __init rs_init(void) B115200 | CS8 | CREAD | HUPCL | CLOCAL; /* is normally B9600 default... */ driver->init_termios.c_ispeed = 115200; driver->init_termios.c_ospeed = 115200; - driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; + driver->flags = TTY_DRIVER_REAL_RAW; tty_set_operations(driver, &rs_ops); serial_driver = driver; - if (tty_register_driver(driver)) - panic("Couldn't register serial driver\n"); - /* do some initializing for the separate ports */ + /* do some initializing for the separate ports */ for (i = 0, info = rs_table; i < NR_PORTS; i++,info++) { if (info->enabled) { if (cris_request_io_interface(info->io_if, @@ -4502,7 +4500,12 @@ static int __init rs_init(void) printk(KERN_INFO "%s%d at %p is a builtin UART with DMA\n", serial_driver->name, info->line, info->ioport); } + tty_port_link_device(&info->port, driver, i); } + + if (tty_register_driver(driver)) + panic("Couldn't register serial driver\n"); + #ifdef CONFIG_ETRAX_FAST_TIMER #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER memset(fast_timers, 0, sizeof(fast_timers)); diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c index 3ad079ffd049..5b9bc19ed134 100644 --- a/drivers/tty/serial/ifx6x60.c +++ b/drivers/tty/serial/ifx6x60.c @@ -800,8 +800,8 @@ static int ifx_spi_create_port(struct ifx_spi_device *ifx_dev) tty_port_init(pport); pport->ops = &ifx_tty_port_ops; ifx_dev->minor = IFX_SPI_TTY_ID; - ifx_dev->tty_dev = tty_register_device(tty_drv, ifx_dev->minor, - &ifx_dev->spi_dev->dev); + ifx_dev->tty_dev = tty_port_register_device(pport, tty_drv, + ifx_dev->minor, &ifx_dev->spi_dev->dev); if (IS_ERR(ifx_dev->tty_dev)) { dev_dbg(&ifx_dev->spi_dev->dev, "%s: registering tty device failed", __func__); diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index d5c689d6217e..20e911724027 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -206,7 +206,7 @@ struct imx_port { unsigned short trcv_delay; /* transceiver delay */ struct clk *clk_ipg; struct clk *clk_per; - struct imx_uart_data *devdata; + const struct imx_uart_data *devdata; }; struct imx_port_ucrs { diff --git a/drivers/tty/serial/ioc4_serial.c b/drivers/tty/serial/ioc4_serial.c index e16894fb2ca3..cc5aca78ad9b 100644 --- a/drivers/tty/serial/ioc4_serial.c +++ b/drivers/tty/serial/ioc4_serial.c @@ -1803,7 +1803,7 @@ static inline int ic4_startup_local(struct uart_port *the_port) ioc4_set_proto(port, the_port->mapbase); /* set the speed of the serial port */ - ioc4_change_speed(the_port, state->port.tty->termios, + ioc4_change_speed(the_port, &state->port.tty->termios, (struct ktermios *)0); return 0; diff --git a/drivers/tty/serial/jsm/jsm_tty.c b/drivers/tty/serial/jsm/jsm_tty.c index 434bd881fcae..71397961773c 100644 --- a/drivers/tty/serial/jsm/jsm_tty.c +++ b/drivers/tty/serial/jsm/jsm_tty.c @@ -161,7 +161,7 @@ static void jsm_tty_send_xchar(struct uart_port *port, char ch) struct ktermios *termios; spin_lock_irqsave(&port->lock, lock_flags); - termios = port->state->port.tty->termios; + termios = &port->state->port.tty->termios; if (ch == termios->c_cc[VSTART]) channel->ch_bd->bd_ops->send_start_character(channel); @@ -250,7 +250,7 @@ static int jsm_tty_open(struct uart_port *port) channel->ch_cached_lsr = 0; channel->ch_stops_sent = 0; - termios = port->state->port.tty->termios; + termios = &port->state->port.tty->termios; channel->ch_c_cflag = termios->c_cflag; channel->ch_c_iflag = termios->c_iflag; channel->ch_c_oflag = termios->c_oflag; @@ -283,7 +283,7 @@ static void jsm_tty_close(struct uart_port *port) jsm_printk(CLOSE, INFO, &channel->ch_bd->pci_dev, "start\n"); bd = channel->ch_bd; - ts = port->state->port.tty->termios; + ts = &port->state->port.tty->termios; channel->ch_flags &= ~(CH_STOPI); @@ -567,7 +567,7 @@ void jsm_input(struct jsm_channel *ch) *input data and return immediately. */ if (!tp || - !(tp->termios->c_cflag & CREAD) ) { + !(tp->termios.c_cflag & CREAD) ) { jsm_printk(READ, INFO, &ch->ch_bd->pci_dev, "input. dropping %d bytes on port %d...\n", data_len, ch->ch_portnum); diff --git a/drivers/tty/serial/lpc32xx_hs.c b/drivers/tty/serial/lpc32xx_hs.c new file mode 100644 index 000000000000..ba3af3bf6d43 --- /dev/null +++ b/drivers/tty/serial/lpc32xx_hs.c @@ -0,0 +1,823 @@ +/* + * High Speed Serial Ports on NXP LPC32xx SoC + * + * Authors: Kevin Wells <kevin.wells@nxp.com> + * Roland Stigge <stigge@antcom.de> + * + * Copyright (C) 2010 NXP Semiconductors + * Copyright (C) 2012 Roland Stigge + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/nmi.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/gpio.h> +#include <linux/of.h> +#include <mach/platform.h> +#include <mach/hardware.h> + +/* + * High Speed UART register offsets + */ +#define LPC32XX_HSUART_FIFO(x) ((x) + 0x00) +#define LPC32XX_HSUART_LEVEL(x) ((x) + 0x04) +#define LPC32XX_HSUART_IIR(x) ((x) + 0x08) +#define LPC32XX_HSUART_CTRL(x) ((x) + 0x0C) +#define LPC32XX_HSUART_RATE(x) ((x) + 0x10) + +#define LPC32XX_HSU_BREAK_DATA (1 << 10) +#define LPC32XX_HSU_ERROR_DATA (1 << 9) +#define LPC32XX_HSU_RX_EMPTY (1 << 8) + +#define LPC32XX_HSU_TX_LEV(n) (((n) >> 8) & 0xFF) +#define LPC32XX_HSU_RX_LEV(n) ((n) & 0xFF) + +#define LPC32XX_HSU_TX_INT_SET (1 << 6) +#define LPC32XX_HSU_RX_OE_INT (1 << 5) +#define LPC32XX_HSU_BRK_INT (1 << 4) +#define LPC32XX_HSU_FE_INT (1 << 3) +#define LPC32XX_HSU_RX_TIMEOUT_INT (1 << 2) +#define LPC32XX_HSU_RX_TRIG_INT (1 << 1) +#define LPC32XX_HSU_TX_INT (1 << 0) + +#define LPC32XX_HSU_HRTS_INV (1 << 21) +#define LPC32XX_HSU_HRTS_TRIG_8B (0x0 << 19) +#define LPC32XX_HSU_HRTS_TRIG_16B (0x1 << 19) +#define LPC32XX_HSU_HRTS_TRIG_32B (0x2 << 19) +#define LPC32XX_HSU_HRTS_TRIG_48B (0x3 << 19) +#define LPC32XX_HSU_HRTS_EN (1 << 18) +#define LPC32XX_HSU_TMO_DISABLED (0x0 << 16) +#define LPC32XX_HSU_TMO_INACT_4B (0x1 << 16) +#define LPC32XX_HSU_TMO_INACT_8B (0x2 << 16) +#define LPC32XX_HSU_TMO_INACT_16B (0x3 << 16) +#define LPC32XX_HSU_HCTS_INV (1 << 15) +#define LPC32XX_HSU_HCTS_EN (1 << 14) +#define LPC32XX_HSU_OFFSET(n) ((n) << 9) +#define LPC32XX_HSU_BREAK (1 << 8) +#define LPC32XX_HSU_ERR_INT_EN (1 << 7) +#define LPC32XX_HSU_RX_INT_EN (1 << 6) +#define LPC32XX_HSU_TX_INT_EN (1 << 5) +#define LPC32XX_HSU_RX_TL1B (0x0 << 2) +#define LPC32XX_HSU_RX_TL4B (0x1 << 2) +#define LPC32XX_HSU_RX_TL8B (0x2 << 2) +#define LPC32XX_HSU_RX_TL16B (0x3 << 2) +#define LPC32XX_HSU_RX_TL32B (0x4 << 2) +#define LPC32XX_HSU_RX_TL48B (0x5 << 2) +#define LPC32XX_HSU_TX_TLEMPTY (0x0 << 0) +#define LPC32XX_HSU_TX_TL0B (0x0 << 0) +#define LPC32XX_HSU_TX_TL4B (0x1 << 0) +#define LPC32XX_HSU_TX_TL8B (0x2 << 0) +#define LPC32XX_HSU_TX_TL16B (0x3 << 0) + +#define MODNAME "lpc32xx_hsuart" + +struct lpc32xx_hsuart_port { + struct uart_port port; +}; + +#define FIFO_READ_LIMIT 128 +#define MAX_PORTS 3 +#define LPC32XX_TTY_NAME "ttyTX" +static struct lpc32xx_hsuart_port lpc32xx_hs_ports[MAX_PORTS]; + +#ifdef CONFIG_SERIAL_HS_LPC32XX_CONSOLE +static void wait_for_xmit_empty(struct uart_port *port) +{ + unsigned int timeout = 10000; + + do { + if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL( + port->membase))) == 0) + break; + if (--timeout == 0) + break; + udelay(1); + } while (1); +} + +static void wait_for_xmit_ready(struct uart_port *port) +{ + unsigned int timeout = 10000; + + while (1) { + if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL( + port->membase))) < 32) + break; + if (--timeout == 0) + break; + udelay(1); + } +} + +static void lpc32xx_hsuart_console_putchar(struct uart_port *port, int ch) +{ + wait_for_xmit_ready(port); + writel((u32)ch, LPC32XX_HSUART_FIFO(port->membase)); +} + +static void lpc32xx_hsuart_console_write(struct console *co, const char *s, + unsigned int count) +{ + struct lpc32xx_hsuart_port *up = &lpc32xx_hs_ports[co->index]; + unsigned long flags; + int locked = 1; + + touch_nmi_watchdog(); + local_irq_save(flags); + if (up->port.sysrq) + locked = 0; + else if (oops_in_progress) + locked = spin_trylock(&up->port.lock); + else + spin_lock(&up->port.lock); + + uart_console_write(&up->port, s, count, lpc32xx_hsuart_console_putchar); + wait_for_xmit_empty(&up->port); + + if (locked) + spin_unlock(&up->port.lock); + local_irq_restore(flags); +} + +static int __init lpc32xx_hsuart_console_setup(struct console *co, + char *options) +{ + struct uart_port *port; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if (co->index >= MAX_PORTS) + co->index = 0; + + port = &lpc32xx_hs_ports[co->index].port; + if (!port->membase) + return -ENODEV; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + return uart_set_options(port, co, baud, parity, bits, flow); +} + +static struct uart_driver lpc32xx_hsuart_reg; +static struct console lpc32xx_hsuart_console = { + .name = LPC32XX_TTY_NAME, + .write = lpc32xx_hsuart_console_write, + .device = uart_console_device, + .setup = lpc32xx_hsuart_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &lpc32xx_hsuart_reg, +}; + +static int __init lpc32xx_hsuart_console_init(void) +{ + register_console(&lpc32xx_hsuart_console); + return 0; +} +console_initcall(lpc32xx_hsuart_console_init); + +#define LPC32XX_HSUART_CONSOLE (&lpc32xx_hsuart_console) +#else +#define LPC32XX_HSUART_CONSOLE NULL +#endif + +static struct uart_driver lpc32xx_hs_reg = { + .owner = THIS_MODULE, + .driver_name = MODNAME, + .dev_name = LPC32XX_TTY_NAME, + .nr = MAX_PORTS, + .cons = LPC32XX_HSUART_CONSOLE, +}; +static int uarts_registered; + +static unsigned int __serial_get_clock_div(unsigned long uartclk, + unsigned long rate) +{ + u32 div, goodrate, hsu_rate, l_hsu_rate, comprate; + u32 rate_diff; + + /* Find the closest divider to get the desired clock rate */ + div = uartclk / rate; + goodrate = hsu_rate = (div / 14) - 1; + if (hsu_rate != 0) + hsu_rate--; + + /* Tweak divider */ + l_hsu_rate = hsu_rate + 3; + rate_diff = 0xFFFFFFFF; + + while (hsu_rate < l_hsu_rate) { + comprate = uartclk / ((hsu_rate + 1) * 14); + if (abs(comprate - rate) < rate_diff) { + goodrate = hsu_rate; + rate_diff = abs(comprate - rate); + } + + hsu_rate++; + } + if (hsu_rate > 0xFF) + hsu_rate = 0xFF; + + return goodrate; +} + +static void __serial_uart_flush(struct uart_port *port) +{ + u32 tmp; + int cnt = 0; + + while ((readl(LPC32XX_HSUART_LEVEL(port->membase)) > 0) && + (cnt++ < FIFO_READ_LIMIT)) + tmp = readl(LPC32XX_HSUART_FIFO(port->membase)); +} + +static void __serial_lpc32xx_rx(struct uart_port *port) +{ + unsigned int tmp, flag; + struct tty_struct *tty = tty_port_tty_get(&port->state->port); + + if (!tty) { + /* Discard data: no tty available */ + while (!(readl(LPC32XX_HSUART_FIFO(port->membase)) & + LPC32XX_HSU_RX_EMPTY)) + ; + + return; + } + + /* Read data from FIFO and push into terminal */ + tmp = readl(LPC32XX_HSUART_FIFO(port->membase)); + while (!(tmp & LPC32XX_HSU_RX_EMPTY)) { + flag = TTY_NORMAL; + port->icount.rx++; + + if (tmp & LPC32XX_HSU_ERROR_DATA) { + /* Framing error */ + writel(LPC32XX_HSU_FE_INT, + LPC32XX_HSUART_IIR(port->membase)); + port->icount.frame++; + flag = TTY_FRAME; + tty_insert_flip_char(tty, 0, TTY_FRAME); + } + + tty_insert_flip_char(tty, (tmp & 0xFF), flag); + + tmp = readl(LPC32XX_HSUART_FIFO(port->membase)); + } + tty_flip_buffer_push(tty); + tty_kref_put(tty); +} + +static void __serial_lpc32xx_tx(struct uart_port *port) +{ + struct circ_buf *xmit = &port->state->xmit; + unsigned int tmp; + + if (port->x_char) { + writel((u32)port->x_char, LPC32XX_HSUART_FIFO(port->membase)); + port->icount.tx++; + port->x_char = 0; + return; + } + + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) + goto exit_tx; + + /* Transfer data */ + while (LPC32XX_HSU_TX_LEV(readl( + LPC32XX_HSUART_LEVEL(port->membase))) < 64) { + writel((u32) xmit->buf[xmit->tail], + LPC32XX_HSUART_FIFO(port->membase)); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + if (uart_circ_empty(xmit)) + break; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + +exit_tx: + if (uart_circ_empty(xmit)) { + tmp = readl(LPC32XX_HSUART_CTRL(port->membase)); + tmp &= ~LPC32XX_HSU_TX_INT_EN; + writel(tmp, LPC32XX_HSUART_CTRL(port->membase)); + } +} + +static irqreturn_t serial_lpc32xx_interrupt(int irq, void *dev_id) +{ + struct uart_port *port = dev_id; + struct tty_struct *tty = tty_port_tty_get(&port->state->port); + u32 status; + + spin_lock(&port->lock); + + /* Read UART status and clear latched interrupts */ + status = readl(LPC32XX_HSUART_IIR(port->membase)); + + if (status & LPC32XX_HSU_BRK_INT) { + /* Break received */ + writel(LPC32XX_HSU_BRK_INT, LPC32XX_HSUART_IIR(port->membase)); + port->icount.brk++; + uart_handle_break(port); + } + + /* Framing error */ + if (status & LPC32XX_HSU_FE_INT) + writel(LPC32XX_HSU_FE_INT, LPC32XX_HSUART_IIR(port->membase)); + + if (status & LPC32XX_HSU_RX_OE_INT) { + /* Receive FIFO overrun */ + writel(LPC32XX_HSU_RX_OE_INT, + LPC32XX_HSUART_IIR(port->membase)); + port->icount.overrun++; + if (tty) { + tty_insert_flip_char(tty, 0, TTY_OVERRUN); + tty_schedule_flip(tty); + } + } + + /* Data received? */ + if (status & (LPC32XX_HSU_RX_TIMEOUT_INT | LPC32XX_HSU_RX_TRIG_INT)) { + __serial_lpc32xx_rx(port); + if (tty) + tty_flip_buffer_push(tty); + } + + /* Transmit data request? */ + if ((status & LPC32XX_HSU_TX_INT) && (!uart_tx_stopped(port))) { + writel(LPC32XX_HSU_TX_INT, LPC32XX_HSUART_IIR(port->membase)); + __serial_lpc32xx_tx(port); + } + + spin_unlock(&port->lock); + tty_kref_put(tty); + + return IRQ_HANDLED; +} + +/* port->lock is not held. */ +static unsigned int serial_lpc32xx_tx_empty(struct uart_port *port) +{ + unsigned int ret = 0; + + if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL(port->membase))) == 0) + ret = TIOCSER_TEMT; + + return ret; +} + +/* port->lock held by caller. */ +static void serial_lpc32xx_set_mctrl(struct uart_port *port, + unsigned int mctrl) +{ + /* No signals are supported on HS UARTs */ +} + +/* port->lock is held by caller and interrupts are disabled. */ +static unsigned int serial_lpc32xx_get_mctrl(struct uart_port *port) +{ + /* No signals are supported on HS UARTs */ + return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; +} + +/* port->lock held by caller. */ +static void serial_lpc32xx_stop_tx(struct uart_port *port) +{ + u32 tmp; + + tmp = readl(LPC32XX_HSUART_CTRL(port->membase)); + tmp &= ~LPC32XX_HSU_TX_INT_EN; + writel(tmp, LPC32XX_HSUART_CTRL(port->membase)); +} + +/* port->lock held by caller. */ +static void serial_lpc32xx_start_tx(struct uart_port *port) +{ + u32 tmp; + + __serial_lpc32xx_tx(port); + tmp = readl(LPC32XX_HSUART_CTRL(port->membase)); + tmp |= LPC32XX_HSU_TX_INT_EN; + writel(tmp, LPC32XX_HSUART_CTRL(port->membase)); +} + +/* port->lock held by caller. */ +static void serial_lpc32xx_stop_rx(struct uart_port *port) +{ + u32 tmp; + + tmp = readl(LPC32XX_HSUART_CTRL(port->membase)); + tmp &= ~(LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN); + writel(tmp, LPC32XX_HSUART_CTRL(port->membase)); + + writel((LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT | + LPC32XX_HSU_FE_INT), LPC32XX_HSUART_IIR(port->membase)); +} + +/* port->lock held by caller. */ +static void serial_lpc32xx_enable_ms(struct uart_port *port) +{ + /* Modem status is not supported */ +} + +/* port->lock is not held. */ +static void serial_lpc32xx_break_ctl(struct uart_port *port, + int break_state) +{ + unsigned long flags; + u32 tmp; + + spin_lock_irqsave(&port->lock, flags); + tmp = readl(LPC32XX_HSUART_CTRL(port->membase)); + if (break_state != 0) + tmp |= LPC32XX_HSU_BREAK; + else + tmp &= ~LPC32XX_HSU_BREAK; + writel(tmp, LPC32XX_HSUART_CTRL(port->membase)); + spin_unlock_irqrestore(&port->lock, flags); +} + +/* LPC3250 Errata HSUART.1: Hang workaround via loopback mode on inactivity */ +static void lpc32xx_loopback_set(resource_size_t mapbase, int state) +{ + int bit; + u32 tmp; + + switch (mapbase) { + case LPC32XX_HS_UART1_BASE: + bit = 0; + break; + case LPC32XX_HS_UART2_BASE: + bit = 1; + break; + case LPC32XX_HS_UART7_BASE: + bit = 6; + break; + default: + WARN(1, "lpc32xx_hs: Warning: Unknown port at %08x\n", mapbase); + return; + } + + tmp = readl(LPC32XX_UARTCTL_CLOOP); + if (state) + tmp |= (1 << bit); + else + tmp &= ~(1 << bit); + writel(tmp, LPC32XX_UARTCTL_CLOOP); +} + +/* port->lock is not held. */ +static int serial_lpc32xx_startup(struct uart_port *port) +{ + int retval; + unsigned long flags; + u32 tmp; + + spin_lock_irqsave(&port->lock, flags); + + __serial_uart_flush(port); + + writel((LPC32XX_HSU_TX_INT | LPC32XX_HSU_FE_INT | + LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT), + LPC32XX_HSUART_IIR(port->membase)); + + writel(0xFF, LPC32XX_HSUART_RATE(port->membase)); + + /* + * Set receiver timeout, HSU offset of 20, no break, no interrupts, + * and default FIFO trigger levels + */ + tmp = LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B | + LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B; + writel(tmp, LPC32XX_HSUART_CTRL(port->membase)); + + lpc32xx_loopback_set(port->mapbase, 0); /* get out of loopback mode */ + + spin_unlock_irqrestore(&port->lock, flags); + + retval = request_irq(port->irq, serial_lpc32xx_interrupt, + 0, MODNAME, port); + if (!retval) + writel((tmp | LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN), + LPC32XX_HSUART_CTRL(port->membase)); + + return retval; +} + +/* port->lock is not held. */ +static void serial_lpc32xx_shutdown(struct uart_port *port) +{ + u32 tmp; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + + tmp = LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B | + LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B; + writel(tmp, LPC32XX_HSUART_CTRL(port->membase)); + + lpc32xx_loopback_set(port->mapbase, 1); /* go to loopback mode */ + + spin_unlock_irqrestore(&port->lock, flags); + + free_irq(port->irq, port); +} + +/* port->lock is not held. */ +static void serial_lpc32xx_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + unsigned long flags; + unsigned int baud, quot; + u32 tmp; + + /* Always 8-bit, no parity, 1 stop bit */ + termios->c_cflag &= ~(CSIZE | CSTOPB | PARENB | PARODD); + termios->c_cflag |= CS8; + + termios->c_cflag &= ~(HUPCL | CMSPAR | CLOCAL | CRTSCTS); + + baud = uart_get_baud_rate(port, termios, old, 0, + port->uartclk / 14); + + quot = __serial_get_clock_div(port->uartclk, baud); + + spin_lock_irqsave(&port->lock, flags); + + /* Ignore characters? */ + tmp = readl(LPC32XX_HSUART_CTRL(port->membase)); + if ((termios->c_cflag & CREAD) == 0) + tmp &= ~(LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN); + else + tmp |= LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN; + writel(tmp, LPC32XX_HSUART_CTRL(port->membase)); + + writel(quot, LPC32XX_HSUART_RATE(port->membase)); + + uart_update_timeout(port, termios->c_cflag, baud); + + spin_unlock_irqrestore(&port->lock, flags); + + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} + +static const char *serial_lpc32xx_type(struct uart_port *port) +{ + return MODNAME; +} + +static void serial_lpc32xx_release_port(struct uart_port *port) +{ + if ((port->iotype == UPIO_MEM32) && (port->mapbase)) { + if (port->flags & UPF_IOREMAP) { + iounmap(port->membase); + port->membase = NULL; + } + + release_mem_region(port->mapbase, SZ_4K); + } +} + +static int serial_lpc32xx_request_port(struct uart_port *port) +{ + int ret = -ENODEV; + + if ((port->iotype == UPIO_MEM32) && (port->mapbase)) { + ret = 0; + + if (!request_mem_region(port->mapbase, SZ_4K, MODNAME)) + ret = -EBUSY; + else if (port->flags & UPF_IOREMAP) { + port->membase = ioremap(port->mapbase, SZ_4K); + if (!port->membase) { + release_mem_region(port->mapbase, SZ_4K); + ret = -ENOMEM; + } + } + } + + return ret; +} + +static void serial_lpc32xx_config_port(struct uart_port *port, int uflags) +{ + int ret; + + ret = serial_lpc32xx_request_port(port); + if (ret < 0) + return; + port->type = PORT_UART00; + port->fifosize = 64; + + __serial_uart_flush(port); + + writel((LPC32XX_HSU_TX_INT | LPC32XX_HSU_FE_INT | + LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT), + LPC32XX_HSUART_IIR(port->membase)); + + writel(0xFF, LPC32XX_HSUART_RATE(port->membase)); + + /* Set receiver timeout, HSU offset of 20, no break, no interrupts, + and default FIFO trigger levels */ + writel(LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B | + LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B, + LPC32XX_HSUART_CTRL(port->membase)); +} + +static int serial_lpc32xx_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + int ret = 0; + + if (ser->type != PORT_UART00) + ret = -EINVAL; + + return ret; +} + +static struct uart_ops serial_lpc32xx_pops = { + .tx_empty = serial_lpc32xx_tx_empty, + .set_mctrl = serial_lpc32xx_set_mctrl, + .get_mctrl = serial_lpc32xx_get_mctrl, + .stop_tx = serial_lpc32xx_stop_tx, + .start_tx = serial_lpc32xx_start_tx, + .stop_rx = serial_lpc32xx_stop_rx, + .enable_ms = serial_lpc32xx_enable_ms, + .break_ctl = serial_lpc32xx_break_ctl, + .startup = serial_lpc32xx_startup, + .shutdown = serial_lpc32xx_shutdown, + .set_termios = serial_lpc32xx_set_termios, + .type = serial_lpc32xx_type, + .release_port = serial_lpc32xx_release_port, + .request_port = serial_lpc32xx_request_port, + .config_port = serial_lpc32xx_config_port, + .verify_port = serial_lpc32xx_verify_port, +}; + +/* + * Register a set of serial devices attached to a platform device + */ +static int __devinit serial_hs_lpc32xx_probe(struct platform_device *pdev) +{ + struct lpc32xx_hsuart_port *p = &lpc32xx_hs_ports[uarts_registered]; + int ret = 0; + struct resource *res; + + if (uarts_registered >= MAX_PORTS) { + dev_err(&pdev->dev, + "Error: Number of possible ports exceeded (%d)!\n", + uarts_registered + 1); + return -ENXIO; + } + + memset(p, 0, sizeof(*p)); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, + "Error getting mem resource for HS UART port %d\n", + uarts_registered); + return -ENXIO; + } + p->port.mapbase = res->start; + p->port.membase = NULL; + + p->port.irq = platform_get_irq(pdev, 0); + if (p->port.irq < 0) { + dev_err(&pdev->dev, "Error getting irq for HS UART port %d\n", + uarts_registered); + return p->port.irq; + } + + p->port.iotype = UPIO_MEM32; + p->port.uartclk = LPC32XX_MAIN_OSC_FREQ; + p->port.regshift = 2; + p->port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT | UPF_IOREMAP; + p->port.dev = &pdev->dev; + p->port.ops = &serial_lpc32xx_pops; + p->port.line = uarts_registered++; + spin_lock_init(&p->port.lock); + + /* send port to loopback mode by default */ + lpc32xx_loopback_set(p->port.mapbase, 1); + + ret = uart_add_one_port(&lpc32xx_hs_reg, &p->port); + + platform_set_drvdata(pdev, p); + + return ret; +} + +/* + * Remove serial ports registered against a platform device. + */ +static int __devexit serial_hs_lpc32xx_remove(struct platform_device *pdev) +{ + struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev); + + uart_remove_one_port(&lpc32xx_hs_reg, &p->port); + + return 0; +} + + +#ifdef CONFIG_PM +static int serial_hs_lpc32xx_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev); + + uart_suspend_port(&lpc32xx_hs_reg, &p->port); + + return 0; +} + +static int serial_hs_lpc32xx_resume(struct platform_device *pdev) +{ + struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev); + + uart_resume_port(&lpc32xx_hs_reg, &p->port); + + return 0; +} +#else +#define serial_hs_lpc32xx_suspend NULL +#define serial_hs_lpc32xx_resume NULL +#endif + +static const struct of_device_id serial_hs_lpc32xx_dt_ids[] = { + { .compatible = "nxp,lpc3220-hsuart" }, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(of, serial_hs_lpc32xx_dt_ids); + +static struct platform_driver serial_hs_lpc32xx_driver = { + .probe = serial_hs_lpc32xx_probe, + .remove = __devexit_p(serial_hs_lpc32xx_remove), + .suspend = serial_hs_lpc32xx_suspend, + .resume = serial_hs_lpc32xx_resume, + .driver = { + .name = MODNAME, + .owner = THIS_MODULE, + .of_match_table = serial_hs_lpc32xx_dt_ids, + }, +}; + +static int __init lpc32xx_hsuart_init(void) +{ + int ret; + + ret = uart_register_driver(&lpc32xx_hs_reg); + if (ret) + return ret; + + ret = platform_driver_register(&serial_hs_lpc32xx_driver); + if (ret) + uart_unregister_driver(&lpc32xx_hs_reg); + + return ret; +} + +static void __exit lpc32xx_hsuart_exit(void) +{ + platform_driver_unregister(&serial_hs_lpc32xx_driver); + uart_unregister_driver(&lpc32xx_hs_reg); +} + +module_init(lpc32xx_hsuart_init); +module_exit(lpc32xx_hsuart_exit); + +MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com>"); +MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>"); +MODULE_DESCRIPTION("NXP LPC32XX High Speed UART driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/max3107.c b/drivers/tty/serial/max3107.c deleted file mode 100644 index 17c7ba805d98..000000000000 --- a/drivers/tty/serial/max3107.c +++ /dev/null @@ -1,1215 +0,0 @@ -/* - * max3107.c - spi uart protocol driver for Maxim 3107 - * Based on max3100.c - * by Christian Pellegrin <chripell@evolware.org> - * and max3110.c - * by Feng Tang <feng.tang@intel.com> - * - * Copyright (C) Aavamobile 2009 - * - * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - * - */ - -#include <linux/delay.h> -#include <linux/device.h> -#include <linux/serial_core.h> -#include <linux/serial.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/gpio.h> -#include <linux/spi/spi.h> -#include <linux/freezer.h> -#include <linux/module.h> -#include "max3107.h" - -static const struct baud_table brg26_ext[] = { - { 300, MAX3107_BRG26_B300 }, - { 600, MAX3107_BRG26_B600 }, - { 1200, MAX3107_BRG26_B1200 }, - { 2400, MAX3107_BRG26_B2400 }, - { 4800, MAX3107_BRG26_B4800 }, - { 9600, MAX3107_BRG26_B9600 }, - { 19200, MAX3107_BRG26_B19200 }, - { 57600, MAX3107_BRG26_B57600 }, - { 115200, MAX3107_BRG26_B115200 }, - { 230400, MAX3107_BRG26_B230400 }, - { 460800, MAX3107_BRG26_B460800 }, - { 921600, MAX3107_BRG26_B921600 }, - { 0, 0 } -}; - -static const struct baud_table brg13_int[] = { - { 300, MAX3107_BRG13_IB300 }, - { 600, MAX3107_BRG13_IB600 }, - { 1200, MAX3107_BRG13_IB1200 }, - { 2400, MAX3107_BRG13_IB2400 }, - { 4800, MAX3107_BRG13_IB4800 }, - { 9600, MAX3107_BRG13_IB9600 }, - { 19200, MAX3107_BRG13_IB19200 }, - { 57600, MAX3107_BRG13_IB57600 }, - { 115200, MAX3107_BRG13_IB115200 }, - { 230400, MAX3107_BRG13_IB230400 }, - { 460800, MAX3107_BRG13_IB460800 }, - { 921600, MAX3107_BRG13_IB921600 }, - { 0, 0 } -}; - -static u32 get_new_brg(int baud, struct max3107_port *s) -{ - int i; - const struct baud_table *baud_tbl = s->baud_tbl; - - for (i = 0; i < 13; i++) { - if (baud == baud_tbl[i].baud) - return baud_tbl[i].new_brg; - } - - return 0; -} - -/* Perform SPI transfer for write/read of device register(s) */ -int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len) -{ - struct spi_message spi_msg; - struct spi_transfer spi_xfer; - - /* Initialize SPI ,message */ - spi_message_init(&spi_msg); - - /* Initialize SPI transfer */ - memset(&spi_xfer, 0, sizeof spi_xfer); - spi_xfer.len = len; - spi_xfer.tx_buf = tx; - spi_xfer.rx_buf = rx; - spi_xfer.speed_hz = MAX3107_SPI_SPEED; - - /* Add SPI transfer to SPI message */ - spi_message_add_tail(&spi_xfer, &spi_msg); - -#ifdef DBG_TRACE_SPI_DATA - { - int i; - pr_info("tx len %d:\n", spi_xfer.len); - for (i = 0 ; i < spi_xfer.len && i < 32 ; i++) - pr_info(" %x", ((u8 *)spi_xfer.tx_buf)[i]); - pr_info("\n"); - } -#endif - - /* Perform synchronous SPI transfer */ - if (spi_sync(s->spi, &spi_msg)) { - dev_err(&s->spi->dev, "spi_sync failure\n"); - return -EIO; - } - -#ifdef DBG_TRACE_SPI_DATA - if (spi_xfer.rx_buf) { - int i; - pr_info("rx len %d:\n", spi_xfer.len); - for (i = 0 ; i < spi_xfer.len && i < 32 ; i++) - pr_info(" %x", ((u8 *)spi_xfer.rx_buf)[i]); - pr_info("\n"); - } -#endif - return 0; -} -EXPORT_SYMBOL_GPL(max3107_rw); - -/* Puts received data to circular buffer */ -static void put_data_to_circ_buf(struct max3107_port *s, unsigned char *data, - int len) -{ - struct uart_port *port = &s->port; - struct tty_struct *tty; - - if (!port->state) - return; - - tty = port->state->port.tty; - if (!tty) - return; - - /* Insert received data */ - tty_insert_flip_string(tty, data, len); - /* Update RX counter */ - port->icount.rx += len; -} - -/* Handle data receiving */ -static void max3107_handlerx(struct max3107_port *s, u16 rxlvl) -{ - int i; - int j; - int len; /* SPI transfer buffer length */ - u16 *buf; - u8 *valid_str; - - if (!s->rx_enabled) - /* RX is disabled */ - return; - - if (rxlvl == 0) { - /* RX fifo is empty */ - return; - } else if (rxlvl >= MAX3107_RX_FIFO_SIZE) { - dev_warn(&s->spi->dev, "Possible RX FIFO overrun %d\n", rxlvl); - /* Ensure sanity of RX level */ - rxlvl = MAX3107_RX_FIFO_SIZE; - } - if ((s->rxbuf == 0) || (s->rxstr == 0)) { - dev_warn(&s->spi->dev, "Rx buffer/str isn't ready\n"); - return; - } - buf = s->rxbuf; - valid_str = s->rxstr; - while (rxlvl) { - pr_debug("rxlvl %d\n", rxlvl); - /* Clear buffer */ - memset(buf, 0, sizeof(u16) * (MAX3107_RX_FIFO_SIZE + 2)); - len = 0; - if (s->irqen_reg & MAX3107_IRQ_RXFIFO_BIT) { - /* First disable RX FIFO interrupt */ - pr_debug("Disabling RX INT\n"); - buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); - s->irqen_reg &= ~MAX3107_IRQ_RXFIFO_BIT; - buf[0] |= s->irqen_reg; - len++; - } - /* Just increase the length by amount of words in FIFO since - * buffer was zeroed and SPI transfer of 0x0000 means reading - * from RX FIFO - */ - len += rxlvl; - /* Append RX level query */ - buf[len] = MAX3107_RXFIFOLVL_REG; - len++; - - /* Perform the SPI transfer */ - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, len * 2)) { - dev_err(&s->spi->dev, "SPI transfer for RX h failed\n"); - return; - } - - /* Skip RX FIFO interrupt disabling word if it was added */ - j = ((len - 1) - rxlvl); - /* Read received words */ - for (i = 0; i < rxlvl; i++, j++) - valid_str[i] = (u8)buf[j]; - put_data_to_circ_buf(s, valid_str, rxlvl); - /* Get new RX level */ - rxlvl = (buf[len - 1] & MAX3107_SPI_RX_DATA_MASK); - } - - if (s->rx_enabled) { - /* RX still enabled, re-enable RX FIFO interrupt */ - pr_debug("Enabling RX INT\n"); - buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); - s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT; - buf[0] |= s->irqen_reg; - if (max3107_rw(s, (u8 *)buf, NULL, 2)) - dev_err(&s->spi->dev, "RX FIFO INT enabling failed\n"); - } - - /* Push the received data to receivers */ - if (s->port.state->port.tty) - tty_flip_buffer_push(s->port.state->port.tty); -} - - -/* Handle data sending */ -static void max3107_handletx(struct max3107_port *s) -{ - struct circ_buf *xmit = &s->port.state->xmit; - int i; - unsigned long flags; - int len; /* SPI transfer buffer length */ - u16 *buf; - - if (!s->tx_fifo_empty) - /* Don't send more data before previous data is sent */ - return; - - if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port)) - /* No data to send or TX is stopped */ - return; - - if (!s->txbuf) { - dev_warn(&s->spi->dev, "Txbuf isn't ready\n"); - return; - } - buf = s->txbuf; - /* Get length of data pending in circular buffer */ - len = uart_circ_chars_pending(xmit); - if (len) { - /* Limit to size of TX FIFO */ - if (len > MAX3107_TX_FIFO_SIZE) - len = MAX3107_TX_FIFO_SIZE; - - pr_debug("txlen %d\n", len); - - /* Update TX counter */ - s->port.icount.tx += len; - - /* TX FIFO will no longer be empty */ - s->tx_fifo_empty = 0; - - i = 0; - if (s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT) { - /* First disable TX empty interrupt */ - pr_debug("Disabling TE INT\n"); - buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); - s->irqen_reg &= ~MAX3107_IRQ_TXEMPTY_BIT; - buf[i] |= s->irqen_reg; - i++; - len++; - } - /* Add data to send */ - spin_lock_irqsave(&s->port.lock, flags); - for ( ; i < len ; i++) { - buf[i] = (MAX3107_WRITE_BIT | MAX3107_THR_REG); - buf[i] |= ((u16)xmit->buf[xmit->tail] & - MAX3107_SPI_TX_DATA_MASK); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - } - spin_unlock_irqrestore(&s->port.lock, flags); - if (!(s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT)) { - /* Enable TX empty interrupt */ - pr_debug("Enabling TE INT\n"); - buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); - s->irqen_reg |= MAX3107_IRQ_TXEMPTY_BIT; - buf[i] |= s->irqen_reg; - i++; - len++; - } - if (!s->tx_enabled) { - /* Enable TX */ - pr_debug("Enable TX\n"); - buf[i] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); - spin_lock_irqsave(&s->data_lock, flags); - s->mode1_reg &= ~MAX3107_MODE1_TXDIS_BIT; - buf[i] |= s->mode1_reg; - spin_unlock_irqrestore(&s->data_lock, flags); - s->tx_enabled = 1; - i++; - len++; - } - - /* Perform the SPI transfer */ - if (max3107_rw(s, (u8 *)buf, NULL, len*2)) { - dev_err(&s->spi->dev, - "SPI transfer TX handling failed\n"); - return; - } - } - - /* Indicate wake up if circular buffer is getting low on data */ - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(&s->port); - -} - -/* Handle interrupts - * Also reads and returns current RX FIFO level - */ -static u16 handle_interrupt(struct max3107_port *s) -{ - u16 buf[4]; /* Buffer for SPI transfers */ - u8 irq_status; - u16 rx_level; - unsigned long flags; - - /* Read IRQ status register */ - buf[0] = MAX3107_IRQSTS_REG; - /* Read status IRQ status register */ - buf[1] = MAX3107_STS_IRQSTS_REG; - /* Read LSR IRQ status register */ - buf[2] = MAX3107_LSR_IRQSTS_REG; - /* Query RX level */ - buf[3] = MAX3107_RXFIFOLVL_REG; - - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 8)) { - dev_err(&s->spi->dev, - "SPI transfer for INTR handling failed\n"); - return 0; - } - - irq_status = (u8)buf[0]; - pr_debug("IRQSTS %x\n", irq_status); - rx_level = (buf[3] & MAX3107_SPI_RX_DATA_MASK); - - if (irq_status & MAX3107_IRQ_LSR_BIT) { - /* LSR interrupt */ - if (buf[2] & MAX3107_LSR_RXTO_BIT) - /* RX timeout interrupt, - * handled by normal RX handling - */ - pr_debug("RX TO INT\n"); - } - - if (irq_status & MAX3107_IRQ_TXEMPTY_BIT) { - /* Tx empty interrupt, - * disable TX and set tx_fifo_empty flag - */ - pr_debug("TE INT, disabling TX\n"); - buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); - spin_lock_irqsave(&s->data_lock, flags); - s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT; - buf[0] |= s->mode1_reg; - spin_unlock_irqrestore(&s->data_lock, flags); - if (max3107_rw(s, (u8 *)buf, NULL, 2)) - dev_err(&s->spi->dev, "SPI transfer TX dis failed\n"); - s->tx_enabled = 0; - s->tx_fifo_empty = 1; - } - - if (irq_status & MAX3107_IRQ_RXFIFO_BIT) - /* RX FIFO interrupt, - * handled by normal RX handling - */ - pr_debug("RFIFO INT\n"); - - /* Return RX level */ - return rx_level; -} - -/* Trigger work thread*/ -static void max3107_dowork(struct max3107_port *s) -{ - if (!work_pending(&s->work) && !freezing(current) && !s->suspended) - queue_work(s->workqueue, &s->work); - else - dev_warn(&s->spi->dev, "interrup isn't serviced normally!\n"); -} - -/* Work thread */ -static void max3107_work(struct work_struct *w) -{ - struct max3107_port *s = container_of(w, struct max3107_port, work); - u16 rxlvl = 0; - int len; /* SPI transfer buffer length */ - u16 buf[5]; /* Buffer for SPI transfers */ - unsigned long flags; - - /* Start by reading current RX FIFO level */ - buf[0] = MAX3107_RXFIFOLVL_REG; - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { - dev_err(&s->spi->dev, "SPI transfer RX lev failed\n"); - rxlvl = 0; - } else { - rxlvl = (buf[0] & MAX3107_SPI_RX_DATA_MASK); - } - - do { - pr_debug("rxlvl %d\n", rxlvl); - - /* Handle RX */ - max3107_handlerx(s, rxlvl); - rxlvl = 0; - - if (s->handle_irq) { - /* Handle pending interrupts - * We also get new RX FIFO level since new data may - * have been received while pushing received data to - * receivers - */ - s->handle_irq = 0; - rxlvl = handle_interrupt(s); - } - - /* Handle TX */ - max3107_handletx(s); - - /* Handle configuration changes */ - len = 0; - spin_lock_irqsave(&s->data_lock, flags); - if (s->mode1_commit) { - pr_debug("mode1_commit\n"); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); - buf[len++] |= s->mode1_reg; - s->mode1_commit = 0; - } - if (s->lcr_commit) { - pr_debug("lcr_commit\n"); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG); - buf[len++] |= s->lcr_reg; - s->lcr_commit = 0; - } - if (s->brg_commit) { - pr_debug("brg_commit\n"); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG); - buf[len++] |= ((s->brg_cfg >> 16) & - MAX3107_SPI_TX_DATA_MASK); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG); - buf[len++] |= ((s->brg_cfg >> 8) & - MAX3107_SPI_TX_DATA_MASK); - buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG); - buf[len++] |= ((s->brg_cfg) & 0xff); - s->brg_commit = 0; - } - spin_unlock_irqrestore(&s->data_lock, flags); - - if (len > 0) { - if (max3107_rw(s, (u8 *)buf, NULL, len * 2)) - dev_err(&s->spi->dev, - "SPI transfer config failed\n"); - } - - /* Reloop if interrupt handling indicated data in RX FIFO */ - } while (rxlvl); - -} - -/* Set sleep mode */ -static void max3107_set_sleep(struct max3107_port *s, int mode) -{ - u16 buf[1]; /* Buffer for SPI transfer */ - unsigned long flags; - pr_debug("enter, mode %d\n", mode); - - buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); - spin_lock_irqsave(&s->data_lock, flags); - switch (mode) { - case MAX3107_DISABLE_FORCED_SLEEP: - s->mode1_reg &= ~MAX3107_MODE1_FORCESLEEP_BIT; - break; - case MAX3107_ENABLE_FORCED_SLEEP: - s->mode1_reg |= MAX3107_MODE1_FORCESLEEP_BIT; - break; - case MAX3107_DISABLE_AUTOSLEEP: - s->mode1_reg &= ~MAX3107_MODE1_AUTOSLEEP_BIT; - break; - case MAX3107_ENABLE_AUTOSLEEP: - s->mode1_reg |= MAX3107_MODE1_AUTOSLEEP_BIT; - break; - default: - spin_unlock_irqrestore(&s->data_lock, flags); - dev_warn(&s->spi->dev, "invalid sleep mode\n"); - return; - } - buf[0] |= s->mode1_reg; - spin_unlock_irqrestore(&s->data_lock, flags); - - if (max3107_rw(s, (u8 *)buf, NULL, 2)) - dev_err(&s->spi->dev, "SPI transfer sleep mode failed\n"); - - if (mode == MAX3107_DISABLE_AUTOSLEEP || - mode == MAX3107_DISABLE_FORCED_SLEEP) - msleep(MAX3107_WAKEUP_DELAY); -} - -/* Perform full register initialization */ -static void max3107_register_init(struct max3107_port *s) -{ - u16 buf[11]; /* Buffer for SPI transfers */ - - /* 1. Configure baud rate, 9600 as default */ - s->baud = 9600; - /* the below is default*/ - if (s->ext_clk) { - s->brg_cfg = MAX3107_BRG26_B9600; - s->baud_tbl = (struct baud_table *)brg26_ext; - } else { - s->brg_cfg = MAX3107_BRG13_IB9600; - s->baud_tbl = (struct baud_table *)brg13_int; - } - - if (s->pdata->init) - s->pdata->init(s); - - buf[0] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG) - | ((s->brg_cfg >> 16) & MAX3107_SPI_TX_DATA_MASK); - buf[1] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG) - | ((s->brg_cfg >> 8) & MAX3107_SPI_TX_DATA_MASK); - buf[2] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG) - | ((s->brg_cfg) & 0xff); - - /* 2. Configure LCR register, 8N1 mode by default */ - s->lcr_reg = MAX3107_LCR_WORD_LEN_8; - buf[3] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG) - | s->lcr_reg; - - /* 3. Configure MODE 1 register */ - s->mode1_reg = 0; - /* Enable IRQ pin */ - s->mode1_reg |= MAX3107_MODE1_IRQSEL_BIT; - /* Disable TX */ - s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT; - s->tx_enabled = 0; - /* RX is enabled */ - s->rx_enabled = 1; - buf[4] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG) - | s->mode1_reg; - - /* 4. Configure MODE 2 register */ - buf[5] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG); - if (s->loopback) { - /* Enable loopback */ - buf[5] |= MAX3107_MODE2_LOOPBACK_BIT; - } - /* Reset FIFOs */ - buf[5] |= MAX3107_MODE2_FIFORST_BIT; - s->tx_fifo_empty = 1; - - /* 5. Configure FIFO trigger level register */ - buf[6] = (MAX3107_WRITE_BIT | MAX3107_FIFOTRIGLVL_REG); - /* RX FIFO trigger for 16 words, TX FIFO trigger not used */ - buf[6] |= (MAX3107_FIFOTRIGLVL_RX(16) | MAX3107_FIFOTRIGLVL_TX(0)); - - /* 6. Configure flow control levels */ - buf[7] = (MAX3107_WRITE_BIT | MAX3107_FLOWLVL_REG); - /* Flow control halt level 96, resume level 48 */ - buf[7] |= (MAX3107_FLOWLVL_RES(48) | MAX3107_FLOWLVL_HALT(96)); - - /* 7. Configure flow control */ - buf[8] = (MAX3107_WRITE_BIT | MAX3107_FLOWCTRL_REG); - /* Enable auto CTS and auto RTS flow control */ - buf[8] |= (MAX3107_FLOWCTRL_AUTOCTS_BIT | MAX3107_FLOWCTRL_AUTORTS_BIT); - - /* 8. Configure RX timeout register */ - buf[9] = (MAX3107_WRITE_BIT | MAX3107_RXTO_REG); - /* Timeout after 48 character intervals */ - buf[9] |= 0x0030; - - /* 9. Configure LSR interrupt enable register */ - buf[10] = (MAX3107_WRITE_BIT | MAX3107_LSR_IRQEN_REG); - /* Enable RX timeout interrupt */ - buf[10] |= MAX3107_LSR_RXTO_BIT; - - /* Perform SPI transfer */ - if (max3107_rw(s, (u8 *)buf, NULL, 22)) - dev_err(&s->spi->dev, "SPI transfer for init failed\n"); - - /* 10. Clear IRQ status register by reading it */ - buf[0] = MAX3107_IRQSTS_REG; - - /* 11. Configure interrupt enable register */ - /* Enable LSR interrupt */ - s->irqen_reg = MAX3107_IRQ_LSR_BIT; - /* Enable RX FIFO interrupt */ - s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT; - buf[1] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG) - | s->irqen_reg; - - /* 12. Clear FIFO reset that was set in step 6 */ - buf[2] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG); - if (s->loopback) { - /* Keep loopback enabled */ - buf[2] |= MAX3107_MODE2_LOOPBACK_BIT; - } - - /* Perform SPI transfer */ - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 6)) - dev_err(&s->spi->dev, "SPI transfer for init failed\n"); - -} - -/* IRQ handler */ -static irqreturn_t max3107_irq(int irqno, void *dev_id) -{ - struct max3107_port *s = dev_id; - - if (irqno != s->spi->irq) { - /* Unexpected IRQ */ - return IRQ_NONE; - } - - /* Indicate irq */ - s->handle_irq = 1; - - /* Trigger work thread */ - max3107_dowork(s); - - return IRQ_HANDLED; -} - -/* HW suspension function - * - * Currently autosleep is used to decrease current consumption, alternative - * approach would be to set the chip to reset mode if UART is not being - * used but that would mess the GPIOs - * - */ -void max3107_hw_susp(struct max3107_port *s, int suspend) -{ - pr_debug("enter, suspend %d\n", suspend); - - if (suspend) { - /* Suspend requested, - * enable autosleep to decrease current consumption - */ - s->suspended = 1; - max3107_set_sleep(s, MAX3107_ENABLE_AUTOSLEEP); - } else { - /* Resume requested, - * disable autosleep - */ - s->suspended = 0; - max3107_set_sleep(s, MAX3107_DISABLE_AUTOSLEEP); - } -} -EXPORT_SYMBOL_GPL(max3107_hw_susp); - -/* Modem status IRQ enabling */ -static void max3107_enable_ms(struct uart_port *port) -{ - /* Modem status not supported */ -} - -/* Data send function */ -static void max3107_start_tx(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - - /* Trigger work thread for sending data */ - max3107_dowork(s); -} - -/* Function for checking that there is no pending transfers */ -static unsigned int max3107_tx_empty(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - - pr_debug("returning %d\n", - (s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit))); - return s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit); -} - -/* Function for stopping RX */ -static void max3107_stop_rx(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - unsigned long flags; - - /* Set RX disabled in MODE 1 register */ - spin_lock_irqsave(&s->data_lock, flags); - s->mode1_reg |= MAX3107_MODE1_RXDIS_BIT; - s->mode1_commit = 1; - spin_unlock_irqrestore(&s->data_lock, flags); - /* Set RX disabled */ - s->rx_enabled = 0; - /* Trigger work thread for doing the actual configuration change */ - max3107_dowork(s); -} - -/* Function for returning control pin states */ -static unsigned int max3107_get_mctrl(struct uart_port *port) -{ - /* DCD and DSR are not wired and CTS/RTS is handled automatically - * so just indicate DSR and CAR asserted - */ - return TIOCM_DSR | TIOCM_CAR; -} - -/* Function for setting control pin states */ -static void max3107_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - /* DCD and DSR are not wired and CTS/RTS is hadnled automatically - * so do nothing - */ -} - -/* Function for configuring UART parameters */ -static void max3107_set_termios(struct uart_port *port, - struct ktermios *termios, - struct ktermios *old) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - struct tty_struct *tty; - int baud; - u16 new_lcr = 0; - u32 new_brg = 0; - unsigned long flags; - - if (!port->state) - return; - - tty = port->state->port.tty; - if (!tty) - return; - - /* Get new LCR register values */ - /* Word size */ - if ((termios->c_cflag & CSIZE) == CS7) - new_lcr |= MAX3107_LCR_WORD_LEN_7; - else - new_lcr |= MAX3107_LCR_WORD_LEN_8; - - /* Parity */ - if (termios->c_cflag & PARENB) { - new_lcr |= MAX3107_LCR_PARITY_BIT; - if (!(termios->c_cflag & PARODD)) - new_lcr |= MAX3107_LCR_EVENPARITY_BIT; - } - - /* Stop bits */ - if (termios->c_cflag & CSTOPB) { - /* 2 stop bits */ - new_lcr |= MAX3107_LCR_STOPLEN_BIT; - } - - /* Mask termios capabilities we don't support */ - termios->c_cflag &= ~CMSPAR; - - /* Set status ignore mask */ - s->port.ignore_status_mask = 0; - if (termios->c_iflag & IGNPAR) - s->port.ignore_status_mask |= MAX3107_ALL_ERRORS; - - /* Set low latency to immediately handle pushed data */ - s->port.state->port.tty->low_latency = 1; - - /* Get new baud rate generator configuration */ - baud = tty_get_baud_rate(tty); - - spin_lock_irqsave(&s->data_lock, flags); - new_brg = get_new_brg(baud, s); - /* if can't find the corrent config, use previous */ - if (!new_brg) { - baud = s->baud; - new_brg = s->brg_cfg; - } - spin_unlock_irqrestore(&s->data_lock, flags); - tty_termios_encode_baud_rate(termios, baud, baud); - s->baud = baud; - - /* Update timeout according to new baud rate */ - uart_update_timeout(port, termios->c_cflag, baud); - - spin_lock_irqsave(&s->data_lock, flags); - if (s->lcr_reg != new_lcr) { - s->lcr_reg = new_lcr; - s->lcr_commit = 1; - } - if (s->brg_cfg != new_brg) { - s->brg_cfg = new_brg; - s->brg_commit = 1; - } - spin_unlock_irqrestore(&s->data_lock, flags); - - /* Trigger work thread for doing the actual configuration change */ - max3107_dowork(s); -} - -/* Port shutdown function */ -static void max3107_shutdown(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - - if (s->suspended && s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 0); - - /* Free the interrupt */ - free_irq(s->spi->irq, s); - - if (s->workqueue) { - /* Flush and destroy work queue */ - flush_workqueue(s->workqueue); - destroy_workqueue(s->workqueue); - s->workqueue = NULL; - } - - /* Suspend HW */ - if (s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 1); -} - -/* Port startup function */ -static int max3107_startup(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - - /* Initialize work queue */ - s->workqueue = create_freezable_workqueue("max3107"); - if (!s->workqueue) { - dev_err(&s->spi->dev, "Workqueue creation failed\n"); - return -EBUSY; - } - INIT_WORK(&s->work, max3107_work); - - /* Setup IRQ */ - if (request_irq(s->spi->irq, max3107_irq, IRQF_TRIGGER_FALLING, - "max3107", s)) { - dev_err(&s->spi->dev, "IRQ reguest failed\n"); - destroy_workqueue(s->workqueue); - s->workqueue = NULL; - return -EBUSY; - } - - /* Resume HW */ - if (s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 0); - - /* Init registers */ - max3107_register_init(s); - - return 0; -} - -/* Port type function */ -static const char *max3107_type(struct uart_port *port) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - return s->spi->modalias; -} - -/* Port release function */ -static void max3107_release_port(struct uart_port *port) -{ - /* Do nothing */ -} - -/* Port request function */ -static int max3107_request_port(struct uart_port *port) -{ - /* Do nothing */ - return 0; -} - -/* Port config function */ -static void max3107_config_port(struct uart_port *port, int flags) -{ - struct max3107_port *s = container_of(port, struct max3107_port, port); - s->port.type = PORT_MAX3107; -} - -/* Port verify function */ -static int max3107_verify_port(struct uart_port *port, - struct serial_struct *ser) -{ - if (ser->type == PORT_UNKNOWN || ser->type == PORT_MAX3107) - return 0; - - return -EINVAL; -} - -/* Port stop TX function */ -static void max3107_stop_tx(struct uart_port *port) -{ - /* Do nothing */ -} - -/* Port break control function */ -static void max3107_break_ctl(struct uart_port *port, int break_state) -{ - /* We don't support break control, do nothing */ -} - - -/* Port functions */ -static struct uart_ops max3107_ops = { - .tx_empty = max3107_tx_empty, - .set_mctrl = max3107_set_mctrl, - .get_mctrl = max3107_get_mctrl, - .stop_tx = max3107_stop_tx, - .start_tx = max3107_start_tx, - .stop_rx = max3107_stop_rx, - .enable_ms = max3107_enable_ms, - .break_ctl = max3107_break_ctl, - .startup = max3107_startup, - .shutdown = max3107_shutdown, - .set_termios = max3107_set_termios, - .type = max3107_type, - .release_port = max3107_release_port, - .request_port = max3107_request_port, - .config_port = max3107_config_port, - .verify_port = max3107_verify_port, -}; - -/* UART driver data */ -static struct uart_driver max3107_uart_driver = { - .owner = THIS_MODULE, - .driver_name = "ttyMAX", - .dev_name = "ttyMAX", - .nr = 1, -}; - -static int driver_registered = 0; - - - -/* 'Generic' platform data */ -static struct max3107_plat generic_plat_data = { - .loopback = 0, - .ext_clk = 1, - .hw_suspend = max3107_hw_susp, - .polled_mode = 0, - .poll_time = 0, -}; - - -/*******************************************************************/ - -/** - * max3107_probe - SPI bus probe entry point - * @spi: the spi device - * - * SPI wants us to probe this device and if appropriate claim it. - * Perform any platform specific requirements and then initialise - * the device. - */ - -int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata) -{ - struct max3107_port *s; - u16 buf[2]; /* Buffer for SPI transfers */ - int retval; - - pr_info("enter max3107 probe\n"); - - /* Allocate port structure */ - s = kzalloc(sizeof(*s), GFP_KERNEL); - if (!s) { - pr_err("Allocating port structure failed\n"); - return -ENOMEM; - } - - s->pdata = pdata; - - /* SPI Rx buffer - * +2 for RX FIFO interrupt - * disabling and RX level query - */ - s->rxbuf = kzalloc(sizeof(u16) * (MAX3107_RX_FIFO_SIZE+2), GFP_KERNEL); - if (!s->rxbuf) { - pr_err("Allocating RX buffer failed\n"); - retval = -ENOMEM; - goto err_free4; - } - s->rxstr = kzalloc(sizeof(u8) * MAX3107_RX_FIFO_SIZE, GFP_KERNEL); - if (!s->rxstr) { - pr_err("Allocating RX buffer failed\n"); - retval = -ENOMEM; - goto err_free3; - } - /* SPI Tx buffer - * SPI transfer buffer - * +3 for TX FIFO empty - * interrupt disabling and - * enabling and TX enabling - */ - s->txbuf = kzalloc(sizeof(u16) * MAX3107_TX_FIFO_SIZE + 3, GFP_KERNEL); - if (!s->txbuf) { - pr_err("Allocating TX buffer failed\n"); - retval = -ENOMEM; - goto err_free2; - } - /* Initialize shared data lock */ - spin_lock_init(&s->data_lock); - - /* SPI intializations */ - dev_set_drvdata(&spi->dev, s); - spi->mode = SPI_MODE_0; - spi->dev.platform_data = pdata; - spi->bits_per_word = 16; - s->ext_clk = pdata->ext_clk; - s->loopback = pdata->loopback; - spi_setup(spi); - s->spi = spi; - - /* Check REV ID to ensure we are talking to what we expect */ - buf[0] = MAX3107_REVID_REG; - if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { - dev_err(&s->spi->dev, "SPI transfer for REVID read failed\n"); - retval = -EIO; - goto err_free1; - } - if ((buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID1 && - (buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID2) { - dev_err(&s->spi->dev, "REVID %x does not match\n", - (buf[0] & MAX3107_SPI_RX_DATA_MASK)); - retval = -ENODEV; - goto err_free1; - } - - /* Disable all interrupts */ - buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG | 0x0000); - buf[0] |= 0x0000; - - /* Configure clock source */ - buf[1] = (MAX3107_WRITE_BIT | MAX3107_CLKSRC_REG); - if (s->ext_clk) { - /* External clock */ - buf[1] |= MAX3107_CLKSRC_EXTCLK_BIT; - } - - /* PLL bypass ON */ - buf[1] |= MAX3107_CLKSRC_PLLBYP_BIT; - - /* Perform SPI transfer */ - if (max3107_rw(s, (u8 *)buf, NULL, 4)) { - dev_err(&s->spi->dev, "SPI transfer for init failed\n"); - retval = -EIO; - goto err_free1; - } - - /* Register UART driver */ - if (!driver_registered) { - retval = uart_register_driver(&max3107_uart_driver); - if (retval) { - dev_err(&s->spi->dev, "Registering UART driver failed\n"); - goto err_free1; - } - driver_registered = 1; - } - - /* Initialize UART port data */ - s->port.fifosize = 128; - s->port.ops = &max3107_ops; - s->port.line = 0; - s->port.dev = &spi->dev; - s->port.uartclk = 9600; - s->port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF; - s->port.irq = s->spi->irq; - s->port.type = PORT_MAX3107; - - /* Add UART port */ - retval = uart_add_one_port(&max3107_uart_driver, &s->port); - if (retval < 0) { - dev_err(&s->spi->dev, "Adding UART port failed\n"); - goto err_free1; - } - - if (pdata->configure) { - retval = pdata->configure(s); - if (retval < 0) - goto err_free1; - } - - /* Go to suspend mode */ - if (pdata->hw_suspend) - pdata->hw_suspend(s, 1); - - return 0; - -err_free1: - kfree(s->txbuf); -err_free2: - kfree(s->rxstr); -err_free3: - kfree(s->rxbuf); -err_free4: - kfree(s); - return retval; -} -EXPORT_SYMBOL_GPL(max3107_probe); - -/* Driver remove function */ -int max3107_remove(struct spi_device *spi) -{ - struct max3107_port *s = dev_get_drvdata(&spi->dev); - - pr_info("enter max3107 remove\n"); - - /* Remove port */ - if (uart_remove_one_port(&max3107_uart_driver, &s->port)) - dev_warn(&s->spi->dev, "Removing UART port failed\n"); - - - /* Free TxRx buffer */ - kfree(s->rxbuf); - kfree(s->rxstr); - kfree(s->txbuf); - - /* Free port structure */ - kfree(s); - - return 0; -} -EXPORT_SYMBOL_GPL(max3107_remove); - -/* Driver suspend function */ -int max3107_suspend(struct spi_device *spi, pm_message_t state) -{ -#ifdef CONFIG_PM - struct max3107_port *s = dev_get_drvdata(&spi->dev); - - pr_debug("enter suspend\n"); - - /* Suspend UART port */ - uart_suspend_port(&max3107_uart_driver, &s->port); - - /* Go to suspend mode */ - if (s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 1); -#endif /* CONFIG_PM */ - return 0; -} -EXPORT_SYMBOL_GPL(max3107_suspend); - -/* Driver resume function */ -int max3107_resume(struct spi_device *spi) -{ -#ifdef CONFIG_PM - struct max3107_port *s = dev_get_drvdata(&spi->dev); - - pr_debug("enter resume\n"); - - /* Resume from suspend */ - if (s->pdata->hw_suspend) - s->pdata->hw_suspend(s, 0); - - /* Resume UART port */ - uart_resume_port(&max3107_uart_driver, &s->port); -#endif /* CONFIG_PM */ - return 0; -} -EXPORT_SYMBOL_GPL(max3107_resume); - -static int max3107_probe_generic(struct spi_device *spi) -{ - return max3107_probe(spi, &generic_plat_data); -} - -/* Spi driver data */ -static struct spi_driver max3107_driver = { - .driver = { - .name = "max3107", - .owner = THIS_MODULE, - }, - .probe = max3107_probe_generic, - .remove = __devexit_p(max3107_remove), - .suspend = max3107_suspend, - .resume = max3107_resume, -}; - -/* Driver init function */ -static int __init max3107_init(void) -{ - pr_info("enter max3107 init\n"); - return spi_register_driver(&max3107_driver); -} - -/* Driver exit function */ -static void __exit max3107_exit(void) -{ - pr_info("enter max3107 exit\n"); - /* Unregister UART driver */ - if (driver_registered) - uart_unregister_driver(&max3107_uart_driver); - spi_unregister_driver(&max3107_driver); -} - -module_init(max3107_init); -module_exit(max3107_exit); - -MODULE_DESCRIPTION("MAX3107 driver"); -MODULE_AUTHOR("Aavamobile"); -MODULE_ALIAS("spi:max3107"); -MODULE_LICENSE("GPL v2"); diff --git a/drivers/tty/serial/max3107.h b/drivers/tty/serial/max3107.h deleted file mode 100644 index 8415fc723b96..000000000000 --- a/drivers/tty/serial/max3107.h +++ /dev/null @@ -1,441 +0,0 @@ -/* - * max3107.h - spi uart protocol driver header for Maxim 3107 - * - * Copyright (C) Aavamobile 2009 - * Based on serial_max3100.h by Christian Pellegrin - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef _MAX3107_H -#define _MAX3107_H - -/* Serial error status definitions */ -#define MAX3107_PARITY_ERROR 1 -#define MAX3107_FRAME_ERROR 2 -#define MAX3107_OVERRUN_ERROR 4 -#define MAX3107_ALL_ERRORS (MAX3107_PARITY_ERROR | \ - MAX3107_FRAME_ERROR | \ - MAX3107_OVERRUN_ERROR) - -/* GPIO definitions */ -#define MAX3107_GPIO_BASE 88 -#define MAX3107_GPIO_COUNT 4 - - -/* GPIO connected to chip's reset pin */ -#define MAX3107_RESET_GPIO 87 - - -/* Chip reset delay */ -#define MAX3107_RESET_DELAY 10 - -/* Chip wakeup delay */ -#define MAX3107_WAKEUP_DELAY 50 - - -/* Sleep mode definitions */ -#define MAX3107_DISABLE_FORCED_SLEEP 0 -#define MAX3107_ENABLE_FORCED_SLEEP 1 -#define MAX3107_DISABLE_AUTOSLEEP 2 -#define MAX3107_ENABLE_AUTOSLEEP 3 - - -/* Definitions for register access with SPI transfers - * - * SPI transfer format: - * - * Master to slave bits xzzzzzzzyyyyyyyy - * Slave to master bits aaaaaaaabbbbbbbb - * - * where: - * x = 0 for reads, 1 for writes - * z = register address - * y = new register value if write, 0 if read - * a = unspecified - * b = register value if read, unspecified if write - */ - -/* SPI speed */ -#define MAX3107_SPI_SPEED (3125000 * 2) - -/* Write bit */ -#define MAX3107_WRITE_BIT (1 << 15) - -/* SPI TX data mask */ -#define MAX3107_SPI_RX_DATA_MASK (0x00ff) - -/* SPI RX data mask */ -#define MAX3107_SPI_TX_DATA_MASK (0x00ff) - -/* Register access masks */ -#define MAX3107_RHR_REG (0x0000) /* RX FIFO */ -#define MAX3107_THR_REG (0x0000) /* TX FIFO */ -#define MAX3107_IRQEN_REG (0x0100) /* IRQ enable */ -#define MAX3107_IRQSTS_REG (0x0200) /* IRQ status */ -#define MAX3107_LSR_IRQEN_REG (0x0300) /* LSR IRQ enable */ -#define MAX3107_LSR_IRQSTS_REG (0x0400) /* LSR IRQ status */ -#define MAX3107_SPCHR_IRQEN_REG (0x0500) /* Special char IRQ enable */ -#define MAX3107_SPCHR_IRQSTS_REG (0x0600) /* Special char IRQ status */ -#define MAX3107_STS_IRQEN_REG (0x0700) /* Status IRQ enable */ -#define MAX3107_STS_IRQSTS_REG (0x0800) /* Status IRQ status */ -#define MAX3107_MODE1_REG (0x0900) /* MODE1 */ -#define MAX3107_MODE2_REG (0x0a00) /* MODE2 */ -#define MAX3107_LCR_REG (0x0b00) /* LCR */ -#define MAX3107_RXTO_REG (0x0c00) /* RX timeout */ -#define MAX3107_HDPIXDELAY_REG (0x0d00) /* Auto transceiver delays */ -#define MAX3107_IRDA_REG (0x0e00) /* IRDA settings */ -#define MAX3107_FLOWLVL_REG (0x0f00) /* Flow control levels */ -#define MAX3107_FIFOTRIGLVL_REG (0x1000) /* FIFO IRQ trigger levels */ -#define MAX3107_TXFIFOLVL_REG (0x1100) /* TX FIFO level */ -#define MAX3107_RXFIFOLVL_REG (0x1200) /* RX FIFO level */ -#define MAX3107_FLOWCTRL_REG (0x1300) /* Flow control */ -#define MAX3107_XON1_REG (0x1400) /* XON1 character */ -#define MAX3107_XON2_REG (0x1500) /* XON2 character */ -#define MAX3107_XOFF1_REG (0x1600) /* XOFF1 character */ -#define MAX3107_XOFF2_REG (0x1700) /* XOFF2 character */ -#define MAX3107_GPIOCFG_REG (0x1800) /* GPIO config */ -#define MAX3107_GPIODATA_REG (0x1900) /* GPIO data */ -#define MAX3107_PLLCFG_REG (0x1a00) /* PLL config */ -#define MAX3107_BRGCFG_REG (0x1b00) /* Baud rate generator conf */ -#define MAX3107_BRGDIVLSB_REG (0x1c00) /* Baud rate divisor LSB */ -#define MAX3107_BRGDIVMSB_REG (0x1d00) /* Baud rate divisor MSB */ -#define MAX3107_CLKSRC_REG (0x1e00) /* Clock source */ -#define MAX3107_REVID_REG (0x1f00) /* Revision identification */ - -/* IRQ register bits */ -#define MAX3107_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */ -#define MAX3107_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */ -#define MAX3107_IRQ_STS_BIT (1 << 2) /* Status interrupt */ -#define MAX3107_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */ -#define MAX3107_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */ -#define MAX3107_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */ -#define MAX3107_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */ -#define MAX3107_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */ - -/* LSR register bits */ -#define MAX3107_LSR_RXTO_BIT (1 << 0) /* RX timeout */ -#define MAX3107_LSR_RXOVR_BIT (1 << 1) /* RX overrun */ -#define MAX3107_LSR_RXPAR_BIT (1 << 2) /* RX parity error */ -#define MAX3107_LSR_FRERR_BIT (1 << 3) /* Frame error */ -#define MAX3107_LSR_RXBRK_BIT (1 << 4) /* RX break */ -#define MAX3107_LSR_RXNOISE_BIT (1 << 5) /* RX noise */ -#define MAX3107_LSR_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_LSR_CTS_BIT (1 << 7) /* CTS pin state */ - -/* Special character register bits */ -#define MAX3107_SPCHR_XON1_BIT (1 << 0) /* XON1 character */ -#define MAX3107_SPCHR_XON2_BIT (1 << 1) /* XON2 character */ -#define MAX3107_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */ -#define MAX3107_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */ -#define MAX3107_SPCHR_BREAK_BIT (1 << 4) /* RX break */ -#define MAX3107_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */ -#define MAX3107_SPCHR_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_SPCHR_UNDEF7_BIT (1 << 7) /* Undefined/not used */ - -/* Status register bits */ -#define MAX3107_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */ -#define MAX3107_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */ -#define MAX3107_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */ -#define MAX3107_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */ -#define MAX3107_STS_UNDEF4_BIT (1 << 4) /* Undefined/not used */ -#define MAX3107_STS_CLKREADY_BIT (1 << 5) /* Clock ready */ -#define MAX3107_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */ -#define MAX3107_STS_UNDEF7_BIT (1 << 7) /* Undefined/not used */ - -/* MODE1 register bits */ -#define MAX3107_MODE1_RXDIS_BIT (1 << 0) /* RX disable */ -#define MAX3107_MODE1_TXDIS_BIT (1 << 1) /* TX disable */ -#define MAX3107_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */ -#define MAX3107_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */ -#define MAX3107_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */ -#define MAX3107_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */ -#define MAX3107_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */ -#define MAX3107_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */ - -/* MODE2 register bits */ -#define MAX3107_MODE2_RST_BIT (1 << 0) /* Chip reset */ -#define MAX3107_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */ -#define MAX3107_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */ -#define MAX3107_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */ -#define MAX3107_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */ -#define MAX3107_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */ -#define MAX3107_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */ -#define MAX3107_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */ - -/* LCR register bits */ -#define MAX3107_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ -#define MAX3107_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 - * - * Word length bits table: - * 00 -> 5 bit words - * 01 -> 6 bit words - * 10 -> 7 bit words - * 11 -> 8 bit words - */ -#define MAX3107_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit - * - * STOP length bit table: - * 0 -> 1 stop bit - * 1 -> 1-1.5 stop bits if - * word length is 5, - * 2 stop bits otherwise - */ -#define MAX3107_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ -#define MAX3107_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ -#define MAX3107_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ -#define MAX3107_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ -#define MAX3107_LCR_RTS_BIT (1 << 7) /* RTS pin control */ -#define MAX3107_LCR_WORD_LEN_5 (0x0000) -#define MAX3107_LCR_WORD_LEN_6 (0x0001) -#define MAX3107_LCR_WORD_LEN_7 (0x0002) -#define MAX3107_LCR_WORD_LEN_8 (0x0003) - - -/* IRDA register bits */ -#define MAX3107_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */ -#define MAX3107_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */ -#define MAX3107_IRDA_SHORTIR_BIT (1 << 2) /* Short SIR mode enable */ -#define MAX3107_IRDA_MIR_BIT (1 << 3) /* MIR mode enable */ -#define MAX3107_IRDA_RXINV_BIT (1 << 4) /* RX logic inversion enable */ -#define MAX3107_IRDA_TXINV_BIT (1 << 5) /* TX logic inversion enable */ -#define MAX3107_IRDA_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_IRDA_UNDEF7_BIT (1 << 7) /* Undefined/not used */ - -/* Flow control trigger level register masks */ -#define MAX3107_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */ -#define MAX3107_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */ -#define MAX3107_FLOWLVL_HALT(words) ((words/8) & 0x000f) -#define MAX3107_FLOWLVL_RES(words) (((words/8) & 0x000f) << 4) - -/* FIFO interrupt trigger level register masks */ -#define MAX3107_FIFOTRIGLVL_TX_MASK (0x000f) /* TX FIFO trigger level */ -#define MAX3107_FIFOTRIGLVL_RX_MASK (0x00f0) /* RX FIFO trigger level */ -#define MAX3107_FIFOTRIGLVL_TX(words) ((words/8) & 0x000f) -#define MAX3107_FIFOTRIGLVL_RX(words) (((words/8) & 0x000f) << 4) - -/* Flow control register bits */ -#define MAX3107_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */ -#define MAX3107_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */ -#define MAX3107_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs - * are used in conjunction with - * XOFF2 for definition of - * special character */ -#define MAX3107_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */ -#define MAX3107_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */ -#define MAX3107_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1 - * - * SWFLOW bits 1 & 0 table: - * 00 -> no transmitter flow - * control - * 01 -> receiver compares - * XON2 and XOFF2 - * and controls - * transmitter - * 10 -> receiver compares - * XON1 and XOFF1 - * and controls - * transmitter - * 11 -> receiver compares - * XON1, XON2, XOFF1 and - * XOFF2 and controls - * transmitter - */ -#define MAX3107_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */ -#define MAX3107_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3 - * - * SWFLOW bits 3 & 2 table: - * 00 -> no received flow - * control - * 01 -> transmitter generates - * XON2 and XOFF2 - * 10 -> transmitter generates - * XON1 and XOFF1 - * 11 -> transmitter generates - * XON1, XON2, XOFF1 and - * XOFF2 - */ - -/* GPIO configuration register bits */ -#define MAX3107_GPIOCFG_GP0OUT_BIT (1 << 0) /* GPIO 0 output enable */ -#define MAX3107_GPIOCFG_GP1OUT_BIT (1 << 1) /* GPIO 1 output enable */ -#define MAX3107_GPIOCFG_GP2OUT_BIT (1 << 2) /* GPIO 2 output enable */ -#define MAX3107_GPIOCFG_GP3OUT_BIT (1 << 3) /* GPIO 3 output enable */ -#define MAX3107_GPIOCFG_GP0OD_BIT (1 << 4) /* GPIO 0 open-drain enable */ -#define MAX3107_GPIOCFG_GP1OD_BIT (1 << 5) /* GPIO 1 open-drain enable */ -#define MAX3107_GPIOCFG_GP2OD_BIT (1 << 6) /* GPIO 2 open-drain enable */ -#define MAX3107_GPIOCFG_GP3OD_BIT (1 << 7) /* GPIO 3 open-drain enable */ - -/* GPIO DATA register bits */ -#define MAX3107_GPIODATA_GP0OUT_BIT (1 << 0) /* GPIO 0 output value */ -#define MAX3107_GPIODATA_GP1OUT_BIT (1 << 1) /* GPIO 1 output value */ -#define MAX3107_GPIODATA_GP2OUT_BIT (1 << 2) /* GPIO 2 output value */ -#define MAX3107_GPIODATA_GP3OUT_BIT (1 << 3) /* GPIO 3 output value */ -#define MAX3107_GPIODATA_GP0IN_BIT (1 << 4) /* GPIO 0 input value */ -#define MAX3107_GPIODATA_GP1IN_BIT (1 << 5) /* GPIO 1 input value */ -#define MAX3107_GPIODATA_GP2IN_BIT (1 << 6) /* GPIO 2 input value */ -#define MAX3107_GPIODATA_GP3IN_BIT (1 << 7) /* GPIO 3 input value */ - -/* PLL configuration register masks */ -#define MAX3107_PLLCFG_PREDIV_MASK (0x003f) /* PLL predivision value */ -#define MAX3107_PLLCFG_PLLFACTOR_MASK (0x00c0) /* PLL multiplication factor */ - -/* Baud rate generator configuration register masks and bits */ -#define MAX3107_BRGCFG_FRACT_MASK (0x000f) /* Fractional portion of - * Baud rate generator divisor - */ -#define MAX3107_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */ -#define MAX3107_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */ -#define MAX3107_BRGCFG_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_BRGCFG_UNDEF7_BIT (1 << 7) /* Undefined/not used */ - -/* Clock source register bits */ -#define MAX3107_CLKSRC_INTOSC_BIT (1 << 0) /* Internal osc enable */ -#define MAX3107_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */ -#define MAX3107_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */ -#define MAX3107_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */ -#define MAX3107_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */ -#define MAX3107_CLKSRC_UNDEF5_BIT (1 << 5) /* Undefined/not used */ -#define MAX3107_CLKSRC_UNDEF6_BIT (1 << 6) /* Undefined/not used */ -#define MAX3107_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */ - - -/* HW definitions */ -#define MAX3107_RX_FIFO_SIZE 128 -#define MAX3107_TX_FIFO_SIZE 128 -#define MAX3107_REVID1 0x00a0 -#define MAX3107_REVID2 0x00a1 - - -/* Baud rate generator configuration values for external clock 13MHz */ -#define MAX3107_BRG13_B300 (0x0A9400 | 0x05) -#define MAX3107_BRG13_B600 (0x054A00 | 0x03) -#define MAX3107_BRG13_B1200 (0x02A500 | 0x01) -#define MAX3107_BRG13_B2400 (0x015200 | 0x09) -#define MAX3107_BRG13_B4800 (0x00A900 | 0x04) -#define MAX3107_BRG13_B9600 (0x005400 | 0x0A) -#define MAX3107_BRG13_B19200 (0x002A00 | 0x05) -#define MAX3107_BRG13_B38400 (0x001500 | 0x03) -#define MAX3107_BRG13_B57600 (0x000E00 | 0x02) -#define MAX3107_BRG13_B115200 (0x000700 | 0x01) -#define MAX3107_BRG13_B230400 (0x000300 | 0x08) -#define MAX3107_BRG13_B460800 (0x000100 | 0x0c) -#define MAX3107_BRG13_B921600 (0x000100 | 0x1c) - -/* Baud rate generator configuration values for external clock 26MHz */ -#define MAX3107_BRG26_B300 (0x152800 | 0x0A) -#define MAX3107_BRG26_B600 (0x0A9400 | 0x05) -#define MAX3107_BRG26_B1200 (0x054A00 | 0x03) -#define MAX3107_BRG26_B2400 (0x02A500 | 0x01) -#define MAX3107_BRG26_B4800 (0x015200 | 0x09) -#define MAX3107_BRG26_B9600 (0x00A900 | 0x04) -#define MAX3107_BRG26_B19200 (0x005400 | 0x0A) -#define MAX3107_BRG26_B38400 (0x002A00 | 0x05) -#define MAX3107_BRG26_B57600 (0x001C00 | 0x03) -#define MAX3107_BRG26_B115200 (0x000E00 | 0x02) -#define MAX3107_BRG26_B230400 (0x000700 | 0x01) -#define MAX3107_BRG26_B460800 (0x000300 | 0x08) -#define MAX3107_BRG26_B921600 (0x000100 | 0x0C) - -/* Baud rate generator configuration values for internal clock */ -#define MAX3107_BRG13_IB300 (0x008000 | 0x00) -#define MAX3107_BRG13_IB600 (0x004000 | 0x00) -#define MAX3107_BRG13_IB1200 (0x002000 | 0x00) -#define MAX3107_BRG13_IB2400 (0x001000 | 0x00) -#define MAX3107_BRG13_IB4800 (0x000800 | 0x00) -#define MAX3107_BRG13_IB9600 (0x000400 | 0x00) -#define MAX3107_BRG13_IB19200 (0x000200 | 0x00) -#define MAX3107_BRG13_IB38400 (0x000100 | 0x00) -#define MAX3107_BRG13_IB57600 (0x000000 | 0x0B) -#define MAX3107_BRG13_IB115200 (0x000000 | 0x05) -#define MAX3107_BRG13_IB230400 (0x000000 | 0x03) -#define MAX3107_BRG13_IB460800 (0x000000 | 0x00) -#define MAX3107_BRG13_IB921600 (0x000000 | 0x00) - - -struct baud_table { - int baud; - u32 new_brg; -}; - -struct max3107_port { - /* UART port structure */ - struct uart_port port; - - /* SPI device structure */ - struct spi_device *spi; - -#if defined(CONFIG_GPIOLIB) - /* GPIO chip structure */ - struct gpio_chip chip; -#endif - - /* Workqueue that does all the magic */ - struct workqueue_struct *workqueue; - struct work_struct work; - - /* Lock for shared data */ - spinlock_t data_lock; - - /* Device configuration */ - int ext_clk; /* 1 if external clock used */ - int loopback; /* Current loopback mode state */ - int baud; /* Current baud rate */ - - /* State flags */ - int suspended; /* Indicates suspend mode */ - int tx_fifo_empty; /* Flag for TX FIFO state */ - int rx_enabled; /* Flag for receiver state */ - int tx_enabled; /* Flag for transmitter state */ - - u16 irqen_reg; /* Current IRQ enable register value */ - /* Shared data */ - u16 mode1_reg; /* Current mode1 register value*/ - int mode1_commit; /* Flag for setting new mode1 register value */ - u16 lcr_reg; /* Current LCR register value */ - int lcr_commit; /* Flag for setting new LCR register value */ - u32 brg_cfg; /* Current Baud rate generator config */ - int brg_commit; /* Flag for setting new baud rate generator - * config - */ - struct baud_table *baud_tbl; - int handle_irq; /* Indicates that IRQ should be handled */ - - /* Rx buffer and str*/ - u16 *rxbuf; - u8 *rxstr; - /* Tx buffer*/ - u16 *txbuf; - - struct max3107_plat *pdata; /* Platform data */ -}; - -/* Platform data structure */ -struct max3107_plat { - /* Loopback mode enable */ - int loopback; - /* External clock enable */ - int ext_clk; - /* Called during the register initialisation */ - void (*init)(struct max3107_port *s); - /* Called when the port is found and configured */ - int (*configure)(struct max3107_port *s); - /* HW suspend function */ - void (*hw_suspend) (struct max3107_port *s, int suspend); - /* Polling mode enable */ - int polled_mode; - /* Polling period if polling mode enabled */ - int poll_time; -}; - -extern int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len); -extern void max3107_hw_susp(struct max3107_port *s, int suspend); -extern int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata); -extern int max3107_remove(struct spi_device *spi); -extern int max3107_suspend(struct spi_device *spi, pm_message_t state); -extern int max3107_resume(struct spi_device *spi); - -#endif /* _LINUX_SERIAL_MAX3107_H */ diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c new file mode 100644 index 000000000000..534e44851b7f --- /dev/null +++ b/drivers/tty/serial/max310x.c @@ -0,0 +1,1259 @@ +/* + * Maxim (Dallas) MAX3107/8 serial driver + * + * Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru> + * + * Based on max3100.c, by Christian Pellegrin <chripell@evolware.org> + * Based on max3110.c, by Feng Tang <feng.tang@intel.com> + * Based on max3107.c, by Aavamobile + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +/* TODO: MAX3109 support (Dual) */ +/* TODO: MAX14830 support (Quad) */ + +#include <linux/module.h> +#include <linux/device.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/regmap.h> +#include <linux/gpio.h> +#include <linux/spi/spi.h> +#include <linux/platform_data/max310x.h> + +#define MAX310X_MAJOR 204 +#define MAX310X_MINOR 209 + +/* MAX310X register definitions */ +#define MAX310X_RHR_REG (0x00) /* RX FIFO */ +#define MAX310X_THR_REG (0x00) /* TX FIFO */ +#define MAX310X_IRQEN_REG (0x01) /* IRQ enable */ +#define MAX310X_IRQSTS_REG (0x02) /* IRQ status */ +#define MAX310X_LSR_IRQEN_REG (0x03) /* LSR IRQ enable */ +#define MAX310X_LSR_IRQSTS_REG (0x04) /* LSR IRQ status */ +#define MAX310X_SPCHR_IRQEN_REG (0x05) /* Special char IRQ enable */ +#define MAX310X_SPCHR_IRQSTS_REG (0x06) /* Special char IRQ status */ +#define MAX310X_STS_IRQEN_REG (0x07) /* Status IRQ enable */ +#define MAX310X_STS_IRQSTS_REG (0x08) /* Status IRQ status */ +#define MAX310X_MODE1_REG (0x09) /* MODE1 */ +#define MAX310X_MODE2_REG (0x0a) /* MODE2 */ +#define MAX310X_LCR_REG (0x0b) /* LCR */ +#define MAX310X_RXTO_REG (0x0c) /* RX timeout */ +#define MAX310X_HDPIXDELAY_REG (0x0d) /* Auto transceiver delays */ +#define MAX310X_IRDA_REG (0x0e) /* IRDA settings */ +#define MAX310X_FLOWLVL_REG (0x0f) /* Flow control levels */ +#define MAX310X_FIFOTRIGLVL_REG (0x10) /* FIFO IRQ trigger levels */ +#define MAX310X_TXFIFOLVL_REG (0x11) /* TX FIFO level */ +#define MAX310X_RXFIFOLVL_REG (0x12) /* RX FIFO level */ +#define MAX310X_FLOWCTRL_REG (0x13) /* Flow control */ +#define MAX310X_XON1_REG (0x14) /* XON1 character */ +#define MAX310X_XON2_REG (0x15) /* XON2 character */ +#define MAX310X_XOFF1_REG (0x16) /* XOFF1 character */ +#define MAX310X_XOFF2_REG (0x17) /* XOFF2 character */ +#define MAX310X_GPIOCFG_REG (0x18) /* GPIO config */ +#define MAX310X_GPIODATA_REG (0x19) /* GPIO data */ +#define MAX310X_PLLCFG_REG (0x1a) /* PLL config */ +#define MAX310X_BRGCFG_REG (0x1b) /* Baud rate generator conf */ +#define MAX310X_BRGDIVLSB_REG (0x1c) /* Baud rate divisor LSB */ +#define MAX310X_BRGDIVMSB_REG (0x1d) /* Baud rate divisor MSB */ +#define MAX310X_CLKSRC_REG (0x1e) /* Clock source */ +/* Only present in MAX3107 */ +#define MAX3107_REVID_REG (0x1f) /* Revision identification */ + +/* IRQ register bits */ +#define MAX310X_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */ +#define MAX310X_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */ +#define MAX310X_IRQ_STS_BIT (1 << 2) /* Status interrupt */ +#define MAX310X_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */ +#define MAX310X_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */ +#define MAX310X_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */ +#define MAX310X_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */ +#define MAX310X_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */ + +/* LSR register bits */ +#define MAX310X_LSR_RXTO_BIT (1 << 0) /* RX timeout */ +#define MAX310X_LSR_RXOVR_BIT (1 << 1) /* RX overrun */ +#define MAX310X_LSR_RXPAR_BIT (1 << 2) /* RX parity error */ +#define MAX310X_LSR_FRERR_BIT (1 << 3) /* Frame error */ +#define MAX310X_LSR_RXBRK_BIT (1 << 4) /* RX break */ +#define MAX310X_LSR_RXNOISE_BIT (1 << 5) /* RX noise */ +#define MAX310X_LSR_CTS_BIT (1 << 7) /* CTS pin state */ + +/* Special character register bits */ +#define MAX310X_SPCHR_XON1_BIT (1 << 0) /* XON1 character */ +#define MAX310X_SPCHR_XON2_BIT (1 << 1) /* XON2 character */ +#define MAX310X_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */ +#define MAX310X_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */ +#define MAX310X_SPCHR_BREAK_BIT (1 << 4) /* RX break */ +#define MAX310X_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */ + +/* Status register bits */ +#define MAX310X_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */ +#define MAX310X_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */ +#define MAX310X_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */ +#define MAX310X_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */ +#define MAX310X_STS_CLKREADY_BIT (1 << 5) /* Clock ready */ +#define MAX310X_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */ + +/* MODE1 register bits */ +#define MAX310X_MODE1_RXDIS_BIT (1 << 0) /* RX disable */ +#define MAX310X_MODE1_TXDIS_BIT (1 << 1) /* TX disable */ +#define MAX310X_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */ +#define MAX310X_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */ +#define MAX310X_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */ +#define MAX310X_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */ +#define MAX310X_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */ +#define MAX310X_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */ + +/* MODE2 register bits */ +#define MAX310X_MODE2_RST_BIT (1 << 0) /* Chip reset */ +#define MAX310X_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */ +#define MAX310X_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */ +#define MAX310X_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */ +#define MAX310X_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */ +#define MAX310X_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */ +#define MAX310X_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */ +#define MAX310X_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */ + +/* LCR register bits */ +#define MAX310X_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ +#define MAX310X_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 + * + * Word length bits table: + * 00 -> 5 bit words + * 01 -> 6 bit words + * 10 -> 7 bit words + * 11 -> 8 bit words + */ +#define MAX310X_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit + * + * STOP length bit table: + * 0 -> 1 stop bit + * 1 -> 1-1.5 stop bits if + * word length is 5, + * 2 stop bits otherwise + */ +#define MAX310X_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ +#define MAX310X_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ +#define MAX310X_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ +#define MAX310X_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ +#define MAX310X_LCR_RTS_BIT (1 << 7) /* RTS pin control */ +#define MAX310X_LCR_WORD_LEN_5 (0x00) +#define MAX310X_LCR_WORD_LEN_6 (0x01) +#define MAX310X_LCR_WORD_LEN_7 (0x02) +#define MAX310X_LCR_WORD_LEN_8 (0x03) + +/* IRDA register bits */ +#define MAX310X_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */ +#define MAX310X_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */ +#define MAX310X_IRDA_SHORTIR_BIT (1 << 2) /* Short SIR mode enable */ +#define MAX310X_IRDA_MIR_BIT (1 << 3) /* MIR mode enable */ +#define MAX310X_IRDA_RXINV_BIT (1 << 4) /* RX logic inversion enable */ +#define MAX310X_IRDA_TXINV_BIT (1 << 5) /* TX logic inversion enable */ + +/* Flow control trigger level register masks */ +#define MAX310X_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */ +#define MAX310X_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */ +#define MAX310X_FLOWLVL_HALT(words) ((words / 8) & 0x0f) +#define MAX310X_FLOWLVL_RES(words) (((words / 8) & 0x0f) << 4) + +/* FIFO interrupt trigger level register masks */ +#define MAX310X_FIFOTRIGLVL_TX_MASK (0x0f) /* TX FIFO trigger level */ +#define MAX310X_FIFOTRIGLVL_RX_MASK (0xf0) /* RX FIFO trigger level */ +#define MAX310X_FIFOTRIGLVL_TX(words) ((words / 8) & 0x0f) +#define MAX310X_FIFOTRIGLVL_RX(words) (((words / 8) & 0x0f) << 4) + +/* Flow control register bits */ +#define MAX310X_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */ +#define MAX310X_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */ +#define MAX310X_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs + * are used in conjunction with + * XOFF2 for definition of + * special character */ +#define MAX310X_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */ +#define MAX310X_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */ +#define MAX310X_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1 + * + * SWFLOW bits 1 & 0 table: + * 00 -> no transmitter flow + * control + * 01 -> receiver compares + * XON2 and XOFF2 + * and controls + * transmitter + * 10 -> receiver compares + * XON1 and XOFF1 + * and controls + * transmitter + * 11 -> receiver compares + * XON1, XON2, XOFF1 and + * XOFF2 and controls + * transmitter + */ +#define MAX310X_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */ +#define MAX310X_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3 + * + * SWFLOW bits 3 & 2 table: + * 00 -> no received flow + * control + * 01 -> transmitter generates + * XON2 and XOFF2 + * 10 -> transmitter generates + * XON1 and XOFF1 + * 11 -> transmitter generates + * XON1, XON2, XOFF1 and + * XOFF2 + */ + +/* GPIO configuration register bits */ +#define MAX310X_GPIOCFG_GP0OUT_BIT (1 << 0) /* GPIO 0 output enable */ +#define MAX310X_GPIOCFG_GP1OUT_BIT (1 << 1) /* GPIO 1 output enable */ +#define MAX310X_GPIOCFG_GP2OUT_BIT (1 << 2) /* GPIO 2 output enable */ +#define MAX310X_GPIOCFG_GP3OUT_BIT (1 << 3) /* GPIO 3 output enable */ +#define MAX310X_GPIOCFG_GP0OD_BIT (1 << 4) /* GPIO 0 open-drain enable */ +#define MAX310X_GPIOCFG_GP1OD_BIT (1 << 5) /* GPIO 1 open-drain enable */ +#define MAX310X_GPIOCFG_GP2OD_BIT (1 << 6) /* GPIO 2 open-drain enable */ +#define MAX310X_GPIOCFG_GP3OD_BIT (1 << 7) /* GPIO 3 open-drain enable */ + +/* GPIO DATA register bits */ +#define MAX310X_GPIODATA_GP0OUT_BIT (1 << 0) /* GPIO 0 output value */ +#define MAX310X_GPIODATA_GP1OUT_BIT (1 << 1) /* GPIO 1 output value */ +#define MAX310X_GPIODATA_GP2OUT_BIT (1 << 2) /* GPIO 2 output value */ +#define MAX310X_GPIODATA_GP3OUT_BIT (1 << 3) /* GPIO 3 output value */ +#define MAX310X_GPIODATA_GP0IN_BIT (1 << 4) /* GPIO 0 input value */ +#define MAX310X_GPIODATA_GP1IN_BIT (1 << 5) /* GPIO 1 input value */ +#define MAX310X_GPIODATA_GP2IN_BIT (1 << 6) /* GPIO 2 input value */ +#define MAX310X_GPIODATA_GP3IN_BIT (1 << 7) /* GPIO 3 input value */ + +/* PLL configuration register masks */ +#define MAX310X_PLLCFG_PREDIV_MASK (0x3f) /* PLL predivision value */ +#define MAX310X_PLLCFG_PLLFACTOR_MASK (0xc0) /* PLL multiplication factor */ + +/* Baud rate generator configuration register bits */ +#define MAX310X_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */ +#define MAX310X_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */ + +/* Clock source register bits */ +#define MAX310X_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */ +#define MAX310X_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */ +#define MAX310X_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */ +#define MAX310X_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */ +#define MAX310X_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */ + +/* Misc definitions */ +#define MAX310X_FIFO_SIZE (128) + +/* MAX3107 specific */ +#define MAX3107_REV_ID (0xa0) +#define MAX3107_REV_MASK (0xfe) + +/* IRQ status bits definitions */ +#define MAX310X_IRQ_TX (MAX310X_IRQ_TXFIFO_BIT | \ + MAX310X_IRQ_TXEMPTY_BIT) +#define MAX310X_IRQ_RX (MAX310X_IRQ_RXFIFO_BIT | \ + MAX310X_IRQ_RXEMPTY_BIT) + +/* Supported chip types */ +enum { + MAX310X_TYPE_MAX3107 = 3107, + MAX310X_TYPE_MAX3108 = 3108, +}; + +struct max310x_port { + struct uart_driver uart; + struct uart_port port; + + const char *name; + int uartclk; + + unsigned int nr_gpio; +#ifdef CONFIG_GPIOLIB + struct gpio_chip gpio; +#endif + + struct regmap *regmap; + struct regmap_config regcfg; + + struct workqueue_struct *wq; + struct work_struct tx_work; + + struct mutex max310x_mutex; + + struct max310x_pdata *pdata; +}; + +static bool max3107_8_reg_writeable(struct device *dev, unsigned int reg) +{ + switch (reg) { + case MAX310X_IRQSTS_REG: + case MAX310X_LSR_IRQSTS_REG: + case MAX310X_SPCHR_IRQSTS_REG: + case MAX310X_STS_IRQSTS_REG: + case MAX310X_TXFIFOLVL_REG: + case MAX310X_RXFIFOLVL_REG: + case MAX3107_REVID_REG: /* Only available on MAX3107 */ + return false; + default: + break; + } + + return true; +} + +static bool max310x_reg_volatile(struct device *dev, unsigned int reg) +{ + switch (reg) { + case MAX310X_RHR_REG: + case MAX310X_IRQSTS_REG: + case MAX310X_LSR_IRQSTS_REG: + case MAX310X_SPCHR_IRQSTS_REG: + case MAX310X_STS_IRQSTS_REG: + case MAX310X_TXFIFOLVL_REG: + case MAX310X_RXFIFOLVL_REG: + case MAX310X_GPIODATA_REG: + return true; + default: + break; + } + + return false; +} + +static bool max310x_reg_precious(struct device *dev, unsigned int reg) +{ + switch (reg) { + case MAX310X_RHR_REG: + case MAX310X_IRQSTS_REG: + case MAX310X_SPCHR_IRQSTS_REG: + case MAX310X_STS_IRQSTS_REG: + return true; + default: + break; + } + + return false; +} + +static void max310x_set_baud(struct max310x_port *s, int baud) +{ + unsigned int mode = 0, div = s->uartclk / baud; + + if (!(div / 16)) { + /* Mode x2 */ + mode = MAX310X_BRGCFG_2XMODE_BIT; + div = (s->uartclk * 2) / baud; + } + + if (!(div / 16)) { + /* Mode x4 */ + mode = MAX310X_BRGCFG_4XMODE_BIT; + div = (s->uartclk * 4) / baud; + } + + regmap_write(s->regmap, MAX310X_BRGDIVMSB_REG, + ((div / 16) >> 8) & 0xff); + regmap_write(s->regmap, MAX310X_BRGDIVLSB_REG, (div / 16) & 0xff); + regmap_write(s->regmap, MAX310X_BRGCFG_REG, (div % 16) | mode); +} + +static void max310x_wait_pll(struct max310x_port *s) +{ + int tryes = 1000; + + /* Wait for PLL only if crystal is used */ + if (!(s->pdata->driver_flags & MAX310X_EXT_CLK)) { + unsigned int sts = 0; + + while (tryes--) { + regmap_read(s->regmap, MAX310X_STS_IRQSTS_REG, &sts); + if (sts & MAX310X_STS_CLKREADY_BIT) + break; + } + } +} + +static int __devinit max310x_update_best_err(unsigned long f, long *besterr) +{ + /* Use baudrate 115200 for calculate error */ + long err = f % (115200 * 16); + + if ((*besterr < 0) || (*besterr > err)) { + *besterr = err; + return 0; + } + + return 1; +} + +static int __devinit max310x_set_ref_clk(struct max310x_port *s) +{ + unsigned int div, clksrc, pllcfg = 0; + long besterr = -1; + unsigned long fdiv, fmul, bestfreq = s->pdata->frequency; + + /* First, update error without PLL */ + max310x_update_best_err(s->pdata->frequency, &besterr); + + /* Try all possible PLL dividers */ + for (div = 1; (div <= 63) && besterr; div++) { + fdiv = DIV_ROUND_CLOSEST(s->pdata->frequency, div); + + /* Try multiplier 6 */ + fmul = fdiv * 6; + if ((fdiv >= 500000) && (fdiv <= 800000)) + if (!max310x_update_best_err(fmul, &besterr)) { + pllcfg = (0 << 6) | div; + bestfreq = fmul; + } + /* Try multiplier 48 */ + fmul = fdiv * 48; + if ((fdiv >= 850000) && (fdiv <= 1200000)) + if (!max310x_update_best_err(fmul, &besterr)) { + pllcfg = (1 << 6) | div; + bestfreq = fmul; + } + /* Try multiplier 96 */ + fmul = fdiv * 96; + if ((fdiv >= 425000) && (fdiv <= 1000000)) + if (!max310x_update_best_err(fmul, &besterr)) { + pllcfg = (2 << 6) | div; + bestfreq = fmul; + } + /* Try multiplier 144 */ + fmul = fdiv * 144; + if ((fdiv >= 390000) && (fdiv <= 667000)) + if (!max310x_update_best_err(fmul, &besterr)) { + pllcfg = (3 << 6) | div; + bestfreq = fmul; + } + } + + /* Configure clock source */ + if (s->pdata->driver_flags & MAX310X_EXT_CLK) + clksrc = MAX310X_CLKSRC_EXTCLK_BIT; + else + clksrc = MAX310X_CLKSRC_CRYST_BIT; + + /* Configure PLL */ + if (pllcfg) { + clksrc |= MAX310X_CLKSRC_PLL_BIT; + regmap_write(s->regmap, MAX310X_PLLCFG_REG, pllcfg); + } else + clksrc |= MAX310X_CLKSRC_PLLBYP_BIT; + + regmap_write(s->regmap, MAX310X_CLKSRC_REG, clksrc); + + if (pllcfg) + max310x_wait_pll(s); + + dev_dbg(s->port.dev, "Reference clock set to %lu Hz\n", bestfreq); + + return (int)bestfreq; +} + +static void max310x_handle_rx(struct max310x_port *s, unsigned int rxlen) +{ + unsigned int sts = 0, ch = 0, flag; + struct tty_struct *tty = tty_port_tty_get(&s->port.state->port); + + if (!tty) + return; + + if (unlikely(rxlen >= MAX310X_FIFO_SIZE)) { + dev_warn(s->port.dev, "Possible RX FIFO overrun %d\n", rxlen); + /* Ensure sanity of RX level */ + rxlen = MAX310X_FIFO_SIZE; + } + + dev_dbg(s->port.dev, "RX Len = %u\n", rxlen); + + while (rxlen--) { + regmap_read(s->regmap, MAX310X_RHR_REG, &ch); + regmap_read(s->regmap, MAX310X_LSR_IRQSTS_REG, &sts); + + sts &= MAX310X_LSR_RXPAR_BIT | MAX310X_LSR_FRERR_BIT | + MAX310X_LSR_RXOVR_BIT | MAX310X_LSR_RXBRK_BIT; + + s->port.icount.rx++; + flag = TTY_NORMAL; + + if (unlikely(sts)) { + if (sts & MAX310X_LSR_RXBRK_BIT) { + s->port.icount.brk++; + if (uart_handle_break(&s->port)) + continue; + } else if (sts & MAX310X_LSR_RXPAR_BIT) + s->port.icount.parity++; + else if (sts & MAX310X_LSR_FRERR_BIT) + s->port.icount.frame++; + else if (sts & MAX310X_LSR_RXOVR_BIT) + s->port.icount.overrun++; + + sts &= s->port.read_status_mask; + if (sts & MAX310X_LSR_RXBRK_BIT) + flag = TTY_BREAK; + else if (sts & MAX310X_LSR_RXPAR_BIT) + flag = TTY_PARITY; + else if (sts & MAX310X_LSR_FRERR_BIT) + flag = TTY_FRAME; + else if (sts & MAX310X_LSR_RXOVR_BIT) + flag = TTY_OVERRUN; + } + + if (uart_handle_sysrq_char(s->port, ch)) + continue; + + if (sts & s->port.ignore_status_mask) + continue; + + uart_insert_char(&s->port, sts, MAX310X_LSR_RXOVR_BIT, + ch, flag); + } + + tty_flip_buffer_push(tty); + + tty_kref_put(tty); +} + +static void max310x_handle_tx(struct max310x_port *s) +{ + struct circ_buf *xmit = &s->port.state->xmit; + unsigned int txlen = 0, to_send; + + if (unlikely(s->port.x_char)) { + regmap_write(s->regmap, MAX310X_THR_REG, s->port.x_char); + s->port.icount.tx++; + s->port.x_char = 0; + return; + } + + if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port)) + return; + + /* Get length of data pending in circular buffer */ + to_send = uart_circ_chars_pending(xmit); + if (likely(to_send)) { + /* Limit to size of TX FIFO */ + regmap_read(s->regmap, MAX310X_TXFIFOLVL_REG, &txlen); + txlen = MAX310X_FIFO_SIZE - txlen; + to_send = (to_send > txlen) ? txlen : to_send; + + dev_dbg(s->port.dev, "TX Len = %u\n", to_send); + + /* Add data to send */ + s->port.icount.tx += to_send; + while (to_send--) { + regmap_write(s->regmap, MAX310X_THR_REG, + xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + }; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&s->port); +} + +static irqreturn_t max310x_ist(int irq, void *dev_id) +{ + struct max310x_port *s = (struct max310x_port *)dev_id; + unsigned int ists = 0, lsr = 0, rxlen = 0; + + mutex_lock(&s->max310x_mutex); + + for (;;) { + /* Read IRQ status & RX FIFO level */ + regmap_read(s->regmap, MAX310X_IRQSTS_REG, &ists); + regmap_read(s->regmap, MAX310X_LSR_IRQSTS_REG, &lsr); + regmap_read(s->regmap, MAX310X_RXFIFOLVL_REG, &rxlen); + if (!ists && !(lsr & MAX310X_LSR_RXTO_BIT) && !rxlen) + break; + + dev_dbg(s->port.dev, "IRQ status: 0x%02x\n", ists); + + if (rxlen) + max310x_handle_rx(s, rxlen); + if (ists & MAX310X_IRQ_TX) + max310x_handle_tx(s); + if (ists & MAX310X_IRQ_CTS_BIT) + uart_handle_cts_change(&s->port, + !!(lsr & MAX310X_LSR_CTS_BIT)); + } + + mutex_unlock(&s->max310x_mutex); + + return IRQ_HANDLED; +} + +static void max310x_wq_proc(struct work_struct *ws) +{ + struct max310x_port *s = container_of(ws, struct max310x_port, tx_work); + + mutex_lock(&s->max310x_mutex); + max310x_handle_tx(s); + mutex_unlock(&s->max310x_mutex); +} + +static void max310x_start_tx(struct uart_port *port) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + + queue_work(s->wq, &s->tx_work); +} + +static void max310x_stop_tx(struct uart_port *port) +{ + /* Do nothing */ +} + +static void max310x_stop_rx(struct uart_port *port) +{ + /* Do nothing */ +} + +static unsigned int max310x_tx_empty(struct uart_port *port) +{ + unsigned int val = 0; + struct max310x_port *s = container_of(port, struct max310x_port, port); + + mutex_lock(&s->max310x_mutex); + regmap_read(s->regmap, MAX310X_TXFIFOLVL_REG, &val); + mutex_unlock(&s->max310x_mutex); + + return val ? 0 : TIOCSER_TEMT; +} + +static void max310x_enable_ms(struct uart_port *port) +{ + /* Modem status not supported */ +} + +static unsigned int max310x_get_mctrl(struct uart_port *port) +{ + /* DCD and DSR are not wired and CTS/RTS is handled automatically + * so just indicate DSR and CAR asserted + */ + return TIOCM_DSR | TIOCM_CAR; +} + +static void max310x_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + /* DCD and DSR are not wired and CTS/RTS is hadnled automatically + * so do nothing + */ +} + +static void max310x_break_ctl(struct uart_port *port, int break_state) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + + mutex_lock(&s->max310x_mutex); + regmap_update_bits(s->regmap, MAX310X_LCR_REG, + MAX310X_LCR_TXBREAK_BIT, + break_state ? MAX310X_LCR_TXBREAK_BIT : 0); + mutex_unlock(&s->max310x_mutex); +} + +static void max310x_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + unsigned int lcr, flow = 0; + int baud; + + mutex_lock(&s->max310x_mutex); + + /* Mask termios capabilities we don't support */ + termios->c_cflag &= ~CMSPAR; + termios->c_iflag &= ~IXANY; + + /* Word size */ + switch (termios->c_cflag & CSIZE) { + case CS5: + lcr = MAX310X_LCR_WORD_LEN_5; + break; + case CS6: + lcr = MAX310X_LCR_WORD_LEN_6; + break; + case CS7: + lcr = MAX310X_LCR_WORD_LEN_7; + break; + case CS8: + default: + lcr = MAX310X_LCR_WORD_LEN_8; + break; + } + + /* Parity */ + if (termios->c_cflag & PARENB) { + lcr |= MAX310X_LCR_PARITY_BIT; + if (!(termios->c_cflag & PARODD)) + lcr |= MAX310X_LCR_EVENPARITY_BIT; + } + + /* Stop bits */ + if (termios->c_cflag & CSTOPB) + lcr |= MAX310X_LCR_STOPLEN_BIT; /* 2 stops */ + + /* Update LCR register */ + regmap_write(s->regmap, MAX310X_LCR_REG, lcr); + + /* Set read status mask */ + port->read_status_mask = MAX310X_LSR_RXOVR_BIT; + if (termios->c_iflag & INPCK) + port->read_status_mask |= MAX310X_LSR_RXPAR_BIT | + MAX310X_LSR_FRERR_BIT; + if (termios->c_iflag & (BRKINT | PARMRK)) + port->read_status_mask |= MAX310X_LSR_RXBRK_BIT; + + /* Set status ignore mask */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNBRK) + port->ignore_status_mask |= MAX310X_LSR_RXBRK_BIT; + if (!(termios->c_cflag & CREAD)) + port->ignore_status_mask |= MAX310X_LSR_RXPAR_BIT | + MAX310X_LSR_RXOVR_BIT | + MAX310X_LSR_FRERR_BIT | + MAX310X_LSR_RXBRK_BIT; + + /* Configure flow control */ + regmap_write(s->regmap, MAX310X_XON1_REG, termios->c_cc[VSTART]); + regmap_write(s->regmap, MAX310X_XOFF1_REG, termios->c_cc[VSTOP]); + if (termios->c_cflag & CRTSCTS) + flow |= MAX310X_FLOWCTRL_AUTOCTS_BIT | + MAX310X_FLOWCTRL_AUTORTS_BIT; + if (termios->c_iflag & IXON) + flow |= MAX310X_FLOWCTRL_SWFLOW3_BIT | + MAX310X_FLOWCTRL_SWFLOWEN_BIT; + if (termios->c_iflag & IXOFF) + flow |= MAX310X_FLOWCTRL_SWFLOW1_BIT | + MAX310X_FLOWCTRL_SWFLOWEN_BIT; + regmap_write(s->regmap, MAX310X_FLOWCTRL_REG, flow); + + /* Get baud rate generator configuration */ + baud = uart_get_baud_rate(port, termios, old, + port->uartclk / 16 / 0xffff, + port->uartclk / 4); + + /* Setup baudrate generator */ + max310x_set_baud(s, baud); + + /* Update timeout according to new baud rate */ + uart_update_timeout(port, termios->c_cflag, baud); + + mutex_unlock(&s->max310x_mutex); +} + +static int max310x_startup(struct uart_port *port) +{ + unsigned int val, line = port->line; + struct max310x_port *s = container_of(port, struct max310x_port, port); + + if (s->pdata->suspend) + s->pdata->suspend(0); + + mutex_lock(&s->max310x_mutex); + + /* Configure baud rate, 9600 as default */ + max310x_set_baud(s, 9600); + + /* Configure LCR register, 8N1 mode by default */ + val = MAX310X_LCR_WORD_LEN_8; + regmap_write(s->regmap, MAX310X_LCR_REG, val); + + /* Configure MODE1 register */ + regmap_update_bits(s->regmap, MAX310X_MODE1_REG, + MAX310X_MODE1_TRNSCVCTRL_BIT, + (s->pdata->uart_flags[line] & MAX310X_AUTO_DIR_CTRL) + ? MAX310X_MODE1_TRNSCVCTRL_BIT : 0); + + /* Configure MODE2 register */ + val = MAX310X_MODE2_RXEMPTINV_BIT; + if (s->pdata->uart_flags[line] & MAX310X_LOOPBACK) + val |= MAX310X_MODE2_LOOPBACK_BIT; + if (s->pdata->uart_flags[line] & MAX310X_ECHO_SUPRESS) + val |= MAX310X_MODE2_ECHOSUPR_BIT; + + /* Reset FIFOs */ + val |= MAX310X_MODE2_FIFORST_BIT; + regmap_write(s->regmap, MAX310X_MODE2_REG, val); + + /* Configure FIFO trigger level register */ + /* RX FIFO trigger for 16 words, TX FIFO trigger for 64 words */ + val = MAX310X_FIFOTRIGLVL_RX(16) | MAX310X_FIFOTRIGLVL_TX(64); + regmap_write(s->regmap, MAX310X_FIFOTRIGLVL_REG, val); + + /* Configure flow control levels */ + /* Flow control halt level 96, resume level 48 */ + val = MAX310X_FLOWLVL_RES(48) | MAX310X_FLOWLVL_HALT(96); + regmap_write(s->regmap, MAX310X_FLOWLVL_REG, val); + + /* Clear timeout register */ + regmap_write(s->regmap, MAX310X_RXTO_REG, 0); + + /* Configure LSR interrupt enable register */ + /* Enable RX timeout interrupt */ + val = MAX310X_LSR_RXTO_BIT; + regmap_write(s->regmap, MAX310X_LSR_IRQEN_REG, val); + + /* Clear FIFO reset */ + regmap_update_bits(s->regmap, MAX310X_MODE2_REG, + MAX310X_MODE2_FIFORST_BIT, 0); + + /* Clear IRQ status register by reading it */ + regmap_read(s->regmap, MAX310X_IRQSTS_REG, &val); + + /* Configure interrupt enable register */ + /* Enable CTS change interrupt */ + val = MAX310X_IRQ_CTS_BIT; + /* Enable RX, TX interrupts */ + val |= MAX310X_IRQ_RX | MAX310X_IRQ_TX; + regmap_write(s->regmap, MAX310X_IRQEN_REG, val); + + mutex_unlock(&s->max310x_mutex); + + return 0; +} + +static void max310x_shutdown(struct uart_port *port) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + + /* Disable all interrupts */ + mutex_lock(&s->max310x_mutex); + regmap_write(s->regmap, MAX310X_IRQEN_REG, 0); + mutex_unlock(&s->max310x_mutex); + + if (s->pdata->suspend) + s->pdata->suspend(1); +} + +static const char *max310x_type(struct uart_port *port) +{ + struct max310x_port *s = container_of(port, struct max310x_port, port); + + return (port->type == PORT_MAX310X) ? s->name : NULL; +} + +static int max310x_request_port(struct uart_port *port) +{ + /* Do nothing */ + return 0; +} + +static void max310x_release_port(struct uart_port *port) +{ + /* Do nothing */ +} + +static void max310x_config_port(struct uart_port *port, int flags) +{ + if (flags & UART_CONFIG_TYPE) + port->type = PORT_MAX310X; +} + +static int max310x_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + if ((ser->type == PORT_UNKNOWN) || (ser->type == PORT_MAX310X)) + return 0; + if (ser->irq == port->irq) + return 0; + + return -EINVAL; +} + +static struct uart_ops max310x_ops = { + .tx_empty = max310x_tx_empty, + .set_mctrl = max310x_set_mctrl, + .get_mctrl = max310x_get_mctrl, + .stop_tx = max310x_stop_tx, + .start_tx = max310x_start_tx, + .stop_rx = max310x_stop_rx, + .enable_ms = max310x_enable_ms, + .break_ctl = max310x_break_ctl, + .startup = max310x_startup, + .shutdown = max310x_shutdown, + .set_termios = max310x_set_termios, + .type = max310x_type, + .request_port = max310x_request_port, + .release_port = max310x_release_port, + .config_port = max310x_config_port, + .verify_port = max310x_verify_port, +}; + +static int max310x_suspend(struct spi_device *spi, pm_message_t state) +{ + int ret; + struct max310x_port *s = dev_get_drvdata(&spi->dev); + + dev_dbg(&spi->dev, "Suspend\n"); + + ret = uart_suspend_port(&s->uart, &s->port); + + mutex_lock(&s->max310x_mutex); + + /* Enable sleep mode */ + regmap_update_bits(s->regmap, MAX310X_MODE1_REG, + MAX310X_MODE1_FORCESLEEP_BIT, + MAX310X_MODE1_FORCESLEEP_BIT); + + mutex_unlock(&s->max310x_mutex); + + if (s->pdata->suspend) + s->pdata->suspend(1); + + return ret; +} + +static int max310x_resume(struct spi_device *spi) +{ + struct max310x_port *s = dev_get_drvdata(&spi->dev); + + dev_dbg(&spi->dev, "Resume\n"); + + if (s->pdata->suspend) + s->pdata->suspend(0); + + mutex_lock(&s->max310x_mutex); + + /* Disable sleep mode */ + regmap_update_bits(s->regmap, MAX310X_MODE1_REG, + MAX310X_MODE1_FORCESLEEP_BIT, + 0); + + max310x_wait_pll(s); + + mutex_unlock(&s->max310x_mutex); + + return uart_resume_port(&s->uart, &s->port); +} + +#ifdef CONFIG_GPIOLIB +static int max310x_gpio_get(struct gpio_chip *chip, unsigned offset) +{ + unsigned int val = 0; + struct max310x_port *s = container_of(chip, struct max310x_port, gpio); + + mutex_lock(&s->max310x_mutex); + regmap_read(s->regmap, MAX310X_GPIODATA_REG, &val); + mutex_unlock(&s->max310x_mutex); + + return !!((val >> 4) & (1 << offset)); +} + +static void max310x_gpio_set(struct gpio_chip *chip, unsigned offset, int value) +{ + struct max310x_port *s = container_of(chip, struct max310x_port, gpio); + + mutex_lock(&s->max310x_mutex); + regmap_update_bits(s->regmap, MAX310X_GPIODATA_REG, 1 << offset, value ? + 1 << offset : 0); + mutex_unlock(&s->max310x_mutex); +} + +static int max310x_gpio_direction_input(struct gpio_chip *chip, unsigned offset) +{ + struct max310x_port *s = container_of(chip, struct max310x_port, gpio); + + mutex_lock(&s->max310x_mutex); + + regmap_update_bits(s->regmap, MAX310X_GPIOCFG_REG, 1 << offset, 0); + + mutex_unlock(&s->max310x_mutex); + + return 0; +} + +static int max310x_gpio_direction_output(struct gpio_chip *chip, + unsigned offset, int value) +{ + struct max310x_port *s = container_of(chip, struct max310x_port, gpio); + + mutex_lock(&s->max310x_mutex); + + regmap_update_bits(s->regmap, MAX310X_GPIOCFG_REG, 1 << offset, + 1 << offset); + regmap_update_bits(s->regmap, MAX310X_GPIODATA_REG, 1 << offset, value ? + 1 << offset : 0); + + mutex_unlock(&s->max310x_mutex); + + return 0; +} +#endif + +/* Generic platform data */ +static struct max310x_pdata generic_plat_data = { + .driver_flags = MAX310X_EXT_CLK, + .uart_flags[0] = MAX310X_ECHO_SUPRESS, + .frequency = 26000000, +}; + +static int __devinit max310x_probe(struct spi_device *spi) +{ + struct max310x_port *s; + struct device *dev = &spi->dev; + int chiptype = spi_get_device_id(spi)->driver_data; + struct max310x_pdata *pdata = dev->platform_data; + unsigned int val = 0; + int ret; + + /* Check for IRQ */ + if (spi->irq <= 0) { + dev_err(dev, "No IRQ specified\n"); + return -ENOTSUPP; + } + + /* Alloc port structure */ + s = devm_kzalloc(dev, sizeof(struct max310x_port), GFP_KERNEL); + if (!s) { + dev_err(dev, "Error allocating port structure\n"); + return -ENOMEM; + } + dev_set_drvdata(dev, s); + + if (!pdata) { + dev_warn(dev, "No platform data supplied, using defaults\n"); + pdata = &generic_plat_data; + } + s->pdata = pdata; + + /* Individual chip settings */ + switch (chiptype) { + case MAX310X_TYPE_MAX3107: + s->name = "MAX3107"; + s->nr_gpio = 4; + s->uart.nr = 1; + s->regcfg.max_register = 0x1f; + break; + case MAX310X_TYPE_MAX3108: + s->name = "MAX3108"; + s->nr_gpio = 4; + s->uart.nr = 1; + s->regcfg.max_register = 0x1e; + break; + default: + dev_err(dev, "Unsupported chip type %i\n", chiptype); + return -ENOTSUPP; + } + + /* Check input frequency */ + if ((pdata->driver_flags & MAX310X_EXT_CLK) && + ((pdata->frequency < 500000) || (pdata->frequency > 35000000))) + goto err_freq; + /* Check frequency for quartz */ + if (!(pdata->driver_flags & MAX310X_EXT_CLK) && + ((pdata->frequency < 1000000) || (pdata->frequency > 4000000))) + goto err_freq; + + mutex_init(&s->max310x_mutex); + + /* Setup SPI bus */ + spi->mode = SPI_MODE_0; + spi->bits_per_word = 8; + spi->max_speed_hz = 26000000; + spi_setup(spi); + + /* Setup regmap */ + s->regcfg.reg_bits = 8; + s->regcfg.val_bits = 8; + s->regcfg.read_flag_mask = 0x00; + s->regcfg.write_flag_mask = 0x80; + s->regcfg.cache_type = REGCACHE_RBTREE; + s->regcfg.writeable_reg = max3107_8_reg_writeable; + s->regcfg.volatile_reg = max310x_reg_volatile; + s->regcfg.precious_reg = max310x_reg_precious; + s->regmap = devm_regmap_init_spi(spi, &s->regcfg); + if (IS_ERR(s->regmap)) { + ret = PTR_ERR(s->regmap); + dev_err(dev, "Failed to initialize register map\n"); + goto err_out; + } + + /* Reset chip & check SPI function */ + ret = regmap_write(s->regmap, MAX310X_MODE2_REG, MAX310X_MODE2_RST_BIT); + if (ret) { + dev_err(dev, "SPI transfer failed\n"); + goto err_out; + } + /* Clear chip reset */ + regmap_write(s->regmap, MAX310X_MODE2_REG, 0); + + switch (chiptype) { + case MAX310X_TYPE_MAX3107: + /* Check REV ID to ensure we are talking to what we expect */ + regmap_read(s->regmap, MAX3107_REVID_REG, &val); + if (((val & MAX3107_REV_MASK) != MAX3107_REV_ID)) { + dev_err(dev, "%s ID 0x%02x does not match\n", + s->name, val); + ret = -ENODEV; + goto err_out; + } + break; + case MAX310X_TYPE_MAX3108: + /* MAX3108 have not REV ID register, we just check default value + * from clocksource register to make sure everything works. + */ + regmap_read(s->regmap, MAX310X_CLKSRC_REG, &val); + if (val != (MAX310X_CLKSRC_EXTCLK_BIT | + MAX310X_CLKSRC_PLLBYP_BIT)) { + dev_err(dev, "%s not present\n", s->name); + ret = -ENODEV; + goto err_out; + } + break; + } + + /* Board specific configure */ + if (pdata->init) + pdata->init(); + if (pdata->suspend) + pdata->suspend(0); + + /* Calculate referecne clock */ + s->uartclk = max310x_set_ref_clk(s); + + /* Disable all interrupts */ + regmap_write(s->regmap, MAX310X_IRQEN_REG, 0); + + /* Setup MODE1 register */ + val = MAX310X_MODE1_IRQSEL_BIT; /* Enable IRQ pin */ + if (pdata->driver_flags & MAX310X_AUTOSLEEP) + val = MAX310X_MODE1_AUTOSLEEP_BIT; + regmap_write(s->regmap, MAX310X_MODE1_REG, val); + + /* Setup interrupt */ + ret = devm_request_threaded_irq(dev, spi->irq, NULL, max310x_ist, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + dev_name(dev), s); + if (ret) { + dev_err(dev, "Unable to reguest IRQ %i\n", spi->irq); + goto err_out; + } + + /* Register UART driver */ + s->uart.owner = THIS_MODULE; + s->uart.driver_name = dev_name(dev); + s->uart.dev_name = "ttyMAX"; + s->uart.major = MAX310X_MAJOR; + s->uart.minor = MAX310X_MINOR; + ret = uart_register_driver(&s->uart); + if (ret) { + dev_err(dev, "Registering UART driver failed\n"); + goto err_out; + } + + /* Initialize workqueue for start TX */ + s->wq = create_freezable_workqueue(dev_name(dev)); + INIT_WORK(&s->tx_work, max310x_wq_proc); + + /* Initialize UART port data */ + s->port.line = 0; + s->port.dev = dev; + s->port.irq = spi->irq; + s->port.type = PORT_MAX310X; + s->port.fifosize = MAX310X_FIFO_SIZE; + s->port.flags = UPF_SKIP_TEST | UPF_FIXED_TYPE; + s->port.iotype = UPIO_PORT; + s->port.membase = (void __iomem *)0xffffffff; /* Bogus value */ + s->port.uartclk = s->uartclk; + s->port.ops = &max310x_ops; + uart_add_one_port(&s->uart, &s->port); + +#ifdef CONFIG_GPIOLIB + /* Setup GPIO cotroller */ + if (pdata->gpio_base) { + s->gpio.owner = THIS_MODULE; + s->gpio.dev = dev; + s->gpio.label = dev_name(dev); + s->gpio.direction_input = max310x_gpio_direction_input; + s->gpio.get = max310x_gpio_get; + s->gpio.direction_output= max310x_gpio_direction_output; + s->gpio.set = max310x_gpio_set; + s->gpio.base = pdata->gpio_base; + s->gpio.ngpio = s->nr_gpio; + if (gpiochip_add(&s->gpio)) { + /* Indicate that we should not call gpiochip_remove */ + s->gpio.base = 0; + } + } else + dev_info(dev, "GPIO support not enabled\n"); +#endif + + /* Go to suspend mode */ + if (pdata->suspend) + pdata->suspend(1); + + return 0; + +err_freq: + dev_err(dev, "Frequency parameter incorrect\n"); + ret = -EINVAL; + +err_out: + dev_set_drvdata(dev, NULL); + devm_kfree(dev, s); + + return ret; +} + +static int __devexit max310x_remove(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + struct max310x_port *s = dev_get_drvdata(dev); + + dev_dbg(dev, "Removing port\n"); + + devm_free_irq(dev, s->port.irq, s); + + destroy_workqueue(s->wq); + + uart_remove_one_port(&s->uart, &s->port); + + uart_unregister_driver(&s->uart); + +#ifdef CONFIG_GPIOLIB + if (s->pdata->gpio_base) + gpiochip_remove(&s->gpio); +#endif + + dev_set_drvdata(dev, NULL); + + if (s->pdata->suspend) + s->pdata->suspend(1); + if (s->pdata->exit) + s->pdata->exit(); + + devm_kfree(dev, s); + + return 0; +} + +static const struct spi_device_id max310x_id_table[] = { + { "max3107", MAX310X_TYPE_MAX3107 }, + { "max3108", MAX310X_TYPE_MAX3108 }, +}; +MODULE_DEVICE_TABLE(spi, max310x_id_table); + +static struct spi_driver max310x_driver = { + .driver = { + .name = "max310x", + .owner = THIS_MODULE, + }, + .probe = max310x_probe, + .remove = __devexit_p(max310x_remove), + .suspend = max310x_suspend, + .resume = max310x_resume, + .id_table = max310x_id_table, +}; +module_spi_driver(max310x_driver); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>"); +MODULE_DESCRIPTION("MAX310X serial driver"); diff --git a/drivers/tty/serial/msm_smd_tty.c b/drivers/tty/serial/msm_smd_tty.c index b25e6ee71443..925d1fa153db 100644 --- a/drivers/tty/serial/msm_smd_tty.c +++ b/drivers/tty/serial/msm_smd_tty.c @@ -223,9 +223,11 @@ static int __init smd_tty_init(void) return ret; for (i = 0; i < smd_tty_channels_len; i++) { - tty_port_init(&smd_tty[smd_tty_channels[i].id].port); - smd_tty[smd_tty_channels[i].id].port.ops = &smd_tty_port_ops; - tty_register_device(smd_tty_driver, smd_tty_channels[i].id, 0); + struct tty_port *port = &smd_tty[smd_tty_channels[i].id].port; + tty_port_init(port); + port->ops = &smd_tty_port_ops; + tty_port_register_device(port, smd_tty_driver, + smd_tty_channels[i].id, NULL); } return 0; diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index 34e71874a892..df443b908ca3 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c @@ -105,6 +105,10 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev, port->uartclk = clk; port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP | UPF_FIXED_PORT | UPF_FIXED_TYPE; + + if (of_find_property(np, "no-loopback-test", NULL)) + port->flags |= UPF_SKIP_TEST; + port->dev = &ofdev->dev; if (type == PORT_TEGRA) @@ -144,8 +148,15 @@ static int __devinit of_platform_serial_probe(struct platform_device *ofdev) switch (port_type) { #ifdef CONFIG_SERIAL_8250 case PORT_8250 ... PORT_MAX_8250: - ret = serial8250_register_port(&port); + { + /* For now the of bindings don't support the extra + 8250 specific bits */ + struct uart_8250_port port8250; + memset(&port8250, 0, sizeof(port8250)); + port8250.port = port; + ret = serial8250_register_8250_port(&port8250); break; + } #endif #ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL case PORT_NWPSERIAL: diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c index d3cda0cb2df0..aa603f221c6a 100644 --- a/drivers/tty/serial/omap-serial.c +++ b/drivers/tty/serial/omap-serial.c @@ -39,6 +39,7 @@ #include <linux/irq.h> #include <linux/pm_runtime.h> #include <linux/of.h> +#include <linux/gpio.h> #include <plat/dma.h> #include <plat/dmtimer.h> @@ -507,6 +508,16 @@ static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl) up->mcr |= mcr; serial_out(up, UART_MCR, up->mcr); pm_runtime_put(&up->pdev->dev); + + if (gpio_is_valid(up->DTR_gpio) && + !!(mctrl & TIOCM_DTR) != up->DTR_active) { + up->DTR_active = !up->DTR_active; + if (gpio_cansleep(up->DTR_gpio)) + schedule_work(&up->qos_work); + else + gpio_set_value(up->DTR_gpio, + up->DTR_active != up->DTR_inverted); + } } static void serial_omap_break_ctl(struct uart_port *port, int break_state) @@ -715,6 +726,9 @@ static void serial_omap_uart_qos_work(struct work_struct *work) qos_work); pm_qos_update_request(&up->pm_qos_request, up->latency); + if (gpio_is_valid(up->DTR_gpio)) + gpio_set_value_cansleep(up->DTR_gpio, + up->DTR_active != up->DTR_inverted); } static void @@ -1435,7 +1449,7 @@ static int serial_omap_probe(struct platform_device *pdev) struct uart_omap_port *up; struct resource *mem, *irq, *dma_tx, *dma_rx; struct omap_uart_port_info *omap_up_info = pdev->dev.platform_data; - int ret = -ENOSPC; + int ret; if (pdev->dev.of_node) omap_up_info = of_get_uart_port_info(&pdev->dev); @@ -1466,10 +1480,29 @@ static int serial_omap_probe(struct platform_device *pdev) if (!dma_tx) return -ENXIO; + if (gpio_is_valid(omap_up_info->DTR_gpio) && + omap_up_info->DTR_present) { + ret = gpio_request(omap_up_info->DTR_gpio, "omap-serial"); + if (ret < 0) + return ret; + ret = gpio_direction_output(omap_up_info->DTR_gpio, + omap_up_info->DTR_inverted); + if (ret < 0) + return ret; + } + up = devm_kzalloc(&pdev->dev, sizeof(*up), GFP_KERNEL); if (!up) return -ENOMEM; + if (gpio_is_valid(omap_up_info->DTR_gpio) && + omap_up_info->DTR_present) { + up->DTR_gpio = omap_up_info->DTR_gpio; + up->DTR_inverted = omap_up_info->DTR_inverted; + } else + up->DTR_gpio = -EINVAL; + up->DTR_active = 0; + up->pdev = pdev; up->port.dev = &pdev->dev; up->port.type = PORT_OMAP; diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c index 558ce8509a9a..4cd6c2381528 100644 --- a/drivers/tty/serial/pch_uart.c +++ b/drivers/tty/serial/pch_uart.c @@ -979,6 +979,10 @@ static unsigned int dma_handle_tx(struct eg20t_port *priv) priv->tx_dma_use = 1; priv->sg_tx_p = kzalloc(sizeof(struct scatterlist)*num, GFP_ATOMIC); + if (!priv->sg_tx_p) { + dev_err(priv->port.dev, "%s:kzalloc Failed\n", __func__); + return 0; + } sg_init_table(priv->sg_tx_p, num); /* Initialize SG table */ sg = priv->sg_tx_p; diff --git a/drivers/tty/serial/pxa.c b/drivers/tty/serial/pxa.c index 5847a4b855f7..9033fc6e0e4e 100644 --- a/drivers/tty/serial/pxa.c +++ b/drivers/tty/serial/pxa.c @@ -670,9 +670,19 @@ serial_pxa_console_write(struct console *co, const char *s, unsigned int count) { struct uart_pxa_port *up = serial_pxa_ports[co->index]; unsigned int ier; + unsigned long flags; + int locked = 1; clk_prepare_enable(up->clk); + local_irq_save(flags); + if (up->port.sysrq) + locked = 0; + else if (oops_in_progress) + locked = spin_trylock(&up->port.lock); + else + spin_lock(&up->port.lock); + /* * First save the IER then disable the interrupts */ @@ -688,6 +698,10 @@ serial_pxa_console_write(struct console *co, const char *s, unsigned int count) wait_for_xmitr(up); serial_out(up, UART_IER, ier); + if (locked) + spin_unlock(&up->port.lock); + local_irq_restore(flags); + clk_disable_unprepare(up->clk); } diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c index 02d07bfcfa8a..5c5e7e09f23e 100644 --- a/drivers/tty/serial/samsung.c +++ b/drivers/tty/serial/samsung.c @@ -529,7 +529,7 @@ static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level, switch (level) { case 3: - if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL) + if (!IS_ERR(ourport->baudclk)) clk_disable(ourport->baudclk); clk_disable(ourport->clk); @@ -538,7 +538,7 @@ static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level, case 0: clk_enable(ourport->clk); - if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL) + if (!IS_ERR(ourport->baudclk)) clk_enable(ourport->baudclk); break; @@ -604,7 +604,6 @@ static unsigned int s3c24xx_serial_getclk(struct s3c24xx_uart_port *ourport, char clkname[MAX_CLK_NAME_LENGTH]; int calc_deviation, deviation = (1 << 30) - 1; - *best_clk = NULL; clk_sel = (ourport->cfg->clk_sel) ? ourport->cfg->clk_sel : ourport->info->def_clk_sel; for (cnt = 0; cnt < info->num_clks; cnt++) { @@ -613,7 +612,7 @@ static unsigned int s3c24xx_serial_getclk(struct s3c24xx_uart_port *ourport, sprintf(clkname, "clk_uart_baud%d", cnt); clk = clk_get(ourport->port.dev, clkname); - if (IS_ERR_OR_NULL(clk)) + if (IS_ERR(clk)) continue; rate = clk_get_rate(clk); @@ -684,7 +683,7 @@ static void s3c24xx_serial_set_termios(struct uart_port *port, { struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port); struct s3c24xx_uart_port *ourport = to_ourport(port); - struct clk *clk = NULL; + struct clk *clk = ERR_PTR(-EINVAL); unsigned long flags; unsigned int baud, quot, clk_sel = 0; unsigned int ulcon; @@ -705,7 +704,7 @@ static void s3c24xx_serial_set_termios(struct uart_port *port, quot = s3c24xx_serial_getclk(ourport, baud, &clk, &clk_sel); if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) quot = port->custom_divisor; - if (!clk) + if (IS_ERR(clk)) return; /* check to see if we need to change clock source */ @@ -713,9 +712,9 @@ static void s3c24xx_serial_set_termios(struct uart_port *port, if (ourport->baudclk != clk) { s3c24xx_serial_setsource(port, clk_sel); - if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) { + if (!IS_ERR(ourport->baudclk)) { clk_disable(ourport->baudclk); - ourport->baudclk = NULL; + ourport->baudclk = ERR_PTR(-EINVAL); } clk_enable(clk); @@ -1036,7 +1035,7 @@ static int s3c24xx_serial_cpufreq_transition(struct notifier_block *nb, if (tty == NULL) goto exit; - termios = tty->termios; + termios = &tty->termios; if (termios == NULL) { printk(KERN_WARNING "%s: no termios?\n", __func__); @@ -1160,7 +1159,11 @@ static ssize_t s3c24xx_serial_show_clksrc(struct device *dev, struct uart_port *port = s3c24xx_dev_to_port(dev); struct s3c24xx_uart_port *ourport = to_ourport(port); - return snprintf(buf, PAGE_SIZE, "* %s\n", ourport->baudclk->name); + if (IS_ERR(ourport->baudclk)) + return -EINVAL; + + return snprintf(buf, PAGE_SIZE, "* %s\n", + ourport->baudclk->name ?: "(null)"); } static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL); @@ -1200,6 +1203,7 @@ static int s3c24xx_serial_probe(struct platform_device *pdev) return -ENODEV; } + ourport->baudclk = ERR_PTR(-EINVAL); ourport->info = ourport->drv_data->info; ourport->cfg = (pdev->dev.platform_data) ? (struct s3c2410_uartcfg *)pdev->dev.platform_data : @@ -1387,7 +1391,7 @@ s3c24xx_serial_get_options(struct uart_port *port, int *baud, sprintf(clk_name, "clk_uart_baud%d", clk_sel); clk = clk_get(port->dev, clk_name); - if (!IS_ERR(clk) && clk != NULL) + if (!IS_ERR(clk)) rate = clk_get_rate(clk); else rate = 1; diff --git a/drivers/tty/serial/sc26xx.c b/drivers/tty/serial/sc26xx.c index e0b4b0a30a5a..3992e48b4c71 100644 --- a/drivers/tty/serial/sc26xx.c +++ b/drivers/tty/serial/sc26xx.c @@ -20,6 +20,7 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/irq.h> +#include <linux/io.h> #if defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index a21dc8e3b7c0..5b308c87b68c 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -159,7 +159,7 @@ static int uart_port_startup(struct tty_struct *tty, struct uart_state *state, retval = uport->ops->startup(uport); if (retval == 0) { if (uart_console(uport) && uport->cons->cflag) { - tty->termios->c_cflag = uport->cons->cflag; + tty->termios.c_cflag = uport->cons->cflag; uport->cons->cflag = 0; } /* @@ -172,7 +172,7 @@ static int uart_port_startup(struct tty_struct *tty, struct uart_state *state, * Setup the RTS and DTR signals once the * port is open and ready to respond. */ - if (tty->termios->c_cflag & CBAUD) + if (tty->termios.c_cflag & CBAUD) uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR); } @@ -240,7 +240,7 @@ static void uart_shutdown(struct tty_struct *tty, struct uart_state *state) /* * Turn off DTR and RTS early. */ - if (!tty || (tty->termios->c_cflag & HUPCL)) + if (!tty || (tty->termios.c_cflag & HUPCL)) uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS); uart_port_shutdown(port); @@ -440,10 +440,10 @@ static void uart_change_speed(struct tty_struct *tty, struct uart_state *state, * If we have no tty, termios, or the port does not exist, * then we can't set the parameters for this port. */ - if (!tty || !tty->termios || uport->type == PORT_UNKNOWN) + if (!tty || uport->type == PORT_UNKNOWN) return; - termios = tty->termios; + termios = &tty->termios; /* * Set flags based on termios cflag @@ -614,7 +614,7 @@ static void uart_throttle(struct tty_struct *tty) if (I_IXOFF(tty)) uart_send_xchar(tty, STOP_CHAR(tty)); - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) uart_clear_mctrl(state->uart_port, TIOCM_RTS); } @@ -630,7 +630,7 @@ static void uart_unthrottle(struct tty_struct *tty) uart_send_xchar(tty, START_CHAR(tty)); } - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) uart_set_mctrl(port, TIOCM_RTS); } @@ -1187,7 +1187,7 @@ static void uart_set_ldisc(struct tty_struct *tty) struct uart_port *uport = state->uart_port; if (uport->ops->set_ldisc) - uport->ops->set_ldisc(uport, tty->termios->c_line); + uport->ops->set_ldisc(uport, tty->termios.c_line); } static void uart_set_termios(struct tty_struct *tty, @@ -1195,7 +1195,7 @@ static void uart_set_termios(struct tty_struct *tty, { struct uart_state *state = tty->driver_data; unsigned long flags; - unsigned int cflag = tty->termios->c_cflag; + unsigned int cflag = tty->termios.c_cflag; /* @@ -1206,9 +1206,9 @@ static void uart_set_termios(struct tty_struct *tty, */ #define RELEVANT_IFLAG(iflag) ((iflag) & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK)) if ((cflag ^ old_termios->c_cflag) == 0 && - tty->termios->c_ospeed == old_termios->c_ospeed && - tty->termios->c_ispeed == old_termios->c_ispeed && - RELEVANT_IFLAG(tty->termios->c_iflag ^ old_termios->c_iflag) == 0) { + tty->termios.c_ospeed == old_termios->c_ospeed && + tty->termios.c_ispeed == old_termios->c_ispeed && + RELEVANT_IFLAG(tty->termios.c_iflag ^ old_termios->c_iflag) == 0) { return; } @@ -1960,8 +1960,8 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport) /* * If that's unset, use the tty termios setting. */ - if (port->tty && port->tty->termios && termios.c_cflag == 0) - termios = *(port->tty->termios); + if (port->tty && termios.c_cflag == 0) + termios = port->tty->termios; if (console_suspend_enabled) uart_change_pm(state, 0); @@ -2346,7 +2346,8 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *uport) * Register the port whether it's detected or not. This allows * setserial to be used to alter this ports parameters. */ - tty_dev = tty_register_device(drv->tty_driver, uport->line, uport->dev); + tty_dev = tty_port_register_device(port, drv->tty_driver, uport->line, + uport->dev); if (likely(!IS_ERR(tty_dev))) { device_set_wakeup_capable(tty_dev, 1); } else { diff --git a/drivers/tty/synclink.c b/drivers/tty/synclink.c index 593d40ad0a6b..666aa1455fc7 100644 --- a/drivers/tty/synclink.c +++ b/drivers/tty/synclink.c @@ -1840,22 +1840,22 @@ static void shutdown(struct mgsl_struct * info) usc_DisableInterrupts(info,RECEIVE_DATA + RECEIVE_STATUS + TRANSMIT_DATA + TRANSMIT_STATUS + IO_PIN + MISC ); usc_DisableDmaInterrupts(info,DICR_MASTER + DICR_TRANSMIT + DICR_RECEIVE); - + /* Disable DMAEN (Port 7, Bit 14) */ /* This disconnects the DMA request signal from the ISA bus */ /* on the ISA adapter. This has no effect for the PCI adapter */ usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) | BIT14)); - + /* Disable INTEN (Port 6, Bit12) */ /* This disconnects the IRQ request signal to the ISA bus */ /* on the ISA adapter. This has no effect for the PCI adapter */ usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) | BIT12)); - - if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) { + + if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) { info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS); usc_set_serial_signals(info); } - + spin_unlock_irqrestore(&info->irq_spinlock,flags); mgsl_release_resources(info); @@ -1895,7 +1895,7 @@ static void mgsl_program_hw(struct mgsl_struct *info) usc_EnableInterrupts(info, IO_PIN); usc_get_serial_signals(info); - if (info->netcount || info->port.tty->termios->c_cflag & CREAD) + if (info->netcount || info->port.tty->termios.c_cflag & CREAD) usc_start_receiver(info); spin_unlock_irqrestore(&info->irq_spinlock,flags); @@ -1908,14 +1908,14 @@ static void mgsl_change_params(struct mgsl_struct *info) unsigned cflag; int bits_per_char; - if (!info->port.tty || !info->port.tty->termios) + if (!info->port.tty) return; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):mgsl_change_params(%s)\n", __FILE__,__LINE__, info->device_name ); - cflag = info->port.tty->termios->c_cflag; + cflag = info->port.tty->termios.c_cflag; /* if B0 rate (hangup) specified then negate DTR and RTS */ /* otherwise assert DTR and RTS */ @@ -2367,8 +2367,8 @@ static void mgsl_throttle(struct tty_struct * tty) if (I_IXOFF(tty)) mgsl_send_xchar(tty, STOP_CHAR(tty)); - - if (tty->termios->c_cflag & CRTSCTS) { + + if (tty->termios.c_cflag & CRTSCTS) { spin_lock_irqsave(&info->irq_spinlock,flags); info->serial_signals &= ~SerialSignal_RTS; usc_set_serial_signals(info); @@ -2401,8 +2401,8 @@ static void mgsl_unthrottle(struct tty_struct * tty) else mgsl_send_xchar(tty, START_CHAR(tty)); } - - if (tty->termios->c_cflag & CRTSCTS) { + + if (tty->termios.c_cflag & CRTSCTS) { spin_lock_irqsave(&info->irq_spinlock,flags); info->serial_signals |= SerialSignal_RTS; usc_set_serial_signals(info); @@ -3045,7 +3045,7 @@ static void mgsl_set_termios(struct tty_struct *tty, struct ktermios *old_termio /* Handle transition to B0 status */ if (old_termios->c_cflag & CBAUD && - !(tty->termios->c_cflag & CBAUD)) { + !(tty->termios.c_cflag & CBAUD)) { info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR); spin_lock_irqsave(&info->irq_spinlock,flags); usc_set_serial_signals(info); @@ -3054,9 +3054,9 @@ static void mgsl_set_termios(struct tty_struct *tty, struct ktermios *old_termio /* Handle transition away from B0 status */ if (!(old_termios->c_cflag & CBAUD) && - tty->termios->c_cflag & CBAUD) { + tty->termios.c_cflag & CBAUD) { info->serial_signals |= SerialSignal_DTR; - if (!(tty->termios->c_cflag & CRTSCTS) || + if (!(tty->termios.c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags)) { info->serial_signals |= SerialSignal_RTS; } @@ -3067,7 +3067,7 @@ static void mgsl_set_termios(struct tty_struct *tty, struct ktermios *old_termio /* Handle turning off CRTSCTS */ if (old_termios->c_cflag & CRTSCTS && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; mgsl_start(tty); } @@ -3287,7 +3287,7 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp, return 0; } - if (tty->termios->c_cflag & CLOCAL) + if (tty->termios.c_cflag & CLOCAL) do_clocal = true; /* Wait for carrier detect and the line to become @@ -3313,7 +3313,7 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp, port->blocked_open++; while (1) { - if (tty->termios->c_cflag & CBAUD) + if (tty->termios.c_cflag & CBAUD) tty_port_raise_dtr_rts(port); set_current_state(TASK_INTERRUPTIBLE); @@ -3338,9 +3338,9 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp, printk("%s(%d):block_til_ready blocking on %s count=%d\n", __FILE__,__LINE__, tty->driver->name, port->count ); - tty_unlock(); + tty_unlock(tty); schedule(); - tty_lock(); + tty_lock(tty); } set_current_state(TASK_RUNNING); @@ -3362,6 +3362,29 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp, } /* end of block_til_ready() */ +static int mgsl_install(struct tty_driver *driver, struct tty_struct *tty) +{ + struct mgsl_struct *info; + int line = tty->index; + + /* verify range of specified line number */ + if (line >= mgsl_device_count) { + printk("%s(%d):mgsl_open with invalid line #%d.\n", + __FILE__, __LINE__, line); + return -ENODEV; + } + + /* find the info structure for the specified line */ + info = mgsl_device_list; + while (info && info->line != line) + info = info->next_device; + if (mgsl_paranoia_check(info, tty->name, "mgsl_open")) + return -ENODEV; + tty->driver_data = info; + + return tty_port_install(&info->port, driver, tty); +} + /* mgsl_open() * * Called when a port is opened. Init and enable port. @@ -3374,26 +3397,10 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp, */ static int mgsl_open(struct tty_struct *tty, struct file * filp) { - struct mgsl_struct *info; - int retval, line; + struct mgsl_struct *info = tty->driver_data; unsigned long flags; + int retval; - /* verify range of specified line number */ - line = tty->index; - if (line >= mgsl_device_count) { - printk("%s(%d):mgsl_open with invalid line #%d.\n", - __FILE__,__LINE__,line); - return -ENODEV; - } - - /* find the info structure for the specified line */ - info = mgsl_device_list; - while(info && info->line != line) - info = info->next_device; - if (mgsl_paranoia_check(info, tty->name, "mgsl_open")) - return -ENODEV; - - tty->driver_data = info; info->port.tty = tty; if (debug_level >= DEBUG_LEVEL_INFO) @@ -4297,6 +4304,7 @@ static struct mgsl_struct* mgsl_allocate_device(void) } /* end of mgsl_allocate_device()*/ static const struct tty_operations mgsl_ops = { + .install = mgsl_install, .open = mgsl_open, .close = mgsl_close, .write = mgsl_write, diff --git a/drivers/tty/synclink_gt.c b/drivers/tty/synclink_gt.c index aa1debf97cc7..45f6136f4e51 100644 --- a/drivers/tty/synclink_gt.c +++ b/drivers/tty/synclink_gt.c @@ -785,7 +785,7 @@ static void set_termios(struct tty_struct *tty, struct ktermios *old_termios) /* Handle transition to B0 status */ if (old_termios->c_cflag & CBAUD && - !(tty->termios->c_cflag & CBAUD)) { + !(tty->termios.c_cflag & CBAUD)) { info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR); spin_lock_irqsave(&info->lock,flags); set_signals(info); @@ -794,9 +794,9 @@ static void set_termios(struct tty_struct *tty, struct ktermios *old_termios) /* Handle transition away from B0 status */ if (!(old_termios->c_cflag & CBAUD) && - tty->termios->c_cflag & CBAUD) { + tty->termios.c_cflag & CBAUD) { info->signals |= SerialSignal_DTR; - if (!(tty->termios->c_cflag & CRTSCTS) || + if (!(tty->termios.c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags)) { info->signals |= SerialSignal_RTS; } @@ -807,7 +807,7 @@ static void set_termios(struct tty_struct *tty, struct ktermios *old_termios) /* Handle turning off CRTSCTS */ if (old_termios->c_cflag & CRTSCTS && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; tx_release(tty); } @@ -1372,7 +1372,7 @@ static void throttle(struct tty_struct * tty) DBGINFO(("%s throttle\n", info->device_name)); if (I_IXOFF(tty)) send_xchar(tty, STOP_CHAR(tty)); - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { spin_lock_irqsave(&info->lock,flags); info->signals &= ~SerialSignal_RTS; set_signals(info); @@ -1397,7 +1397,7 @@ static void unthrottle(struct tty_struct * tty) else send_xchar(tty, START_CHAR(tty)); } - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { spin_lock_irqsave(&info->lock,flags); info->signals |= SerialSignal_RTS; set_signals(info); @@ -2493,7 +2493,7 @@ static void shutdown(struct slgt_info *info) slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); - if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) { + if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) { info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS); set_signals(info); } @@ -2534,7 +2534,7 @@ static void program_hw(struct slgt_info *info) get_signals(info); if (info->netcount || - (info->port.tty && info->port.tty->termios->c_cflag & CREAD)) + (info->port.tty && info->port.tty->termios.c_cflag & CREAD)) rx_start(info); spin_unlock_irqrestore(&info->lock,flags); @@ -2548,11 +2548,11 @@ static void change_params(struct slgt_info *info) unsigned cflag; int bits_per_char; - if (!info->port.tty || !info->port.tty->termios) + if (!info->port.tty) return; DBGINFO(("%s change_params\n", info->device_name)); - cflag = info->port.tty->termios->c_cflag; + cflag = info->port.tty->termios.c_cflag; /* if B0 rate (hangup) specified then negate DTR and RTS */ /* otherwise assert DTR and RTS */ @@ -3292,7 +3292,7 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp, return 0; } - if (tty->termios->c_cflag & CLOCAL) + if (tty->termios.c_cflag & CLOCAL) do_clocal = true; /* Wait for carrier detect and the line to become @@ -3314,7 +3314,7 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp, port->blocked_open++; while (1) { - if ((tty->termios->c_cflag & CBAUD)) + if ((tty->termios.c_cflag & CBAUD)) tty_port_raise_dtr_rts(port); set_current_state(TASK_INTERRUPTIBLE); @@ -3336,9 +3336,9 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp, } DBGINFO(("%s block_til_ready wait\n", tty->driver->name)); - tty_unlock(); + tty_unlock(tty); schedule(); - tty_lock(); + tty_lock(tty); } set_current_state(TASK_RUNNING); @@ -3689,8 +3689,11 @@ static void device_init(int adapter_num, struct pci_dev *pdev) } } - for (i=0; i < port_count; ++i) - tty_register_device(serial_driver, port_array[i]->line, &(port_array[i]->pdev->dev)); + for (i = 0; i < port_count; ++i) { + struct slgt_info *info = port_array[i]; + tty_port_register_device(&info->port, serial_driver, info->line, + &info->pdev->dev); + } } static int __devinit init_one(struct pci_dev *dev, diff --git a/drivers/tty/synclinkmp.c b/drivers/tty/synclinkmp.c index a3dddc12d2fe..53429c890a89 100644 --- a/drivers/tty/synclinkmp.c +++ b/drivers/tty/synclinkmp.c @@ -711,15 +711,11 @@ static void ldisc_receive_buf(struct tty_struct *tty, /* tty callbacks */ -/* Called when a port is opened. Init and enable port. - */ -static int open(struct tty_struct *tty, struct file *filp) +static int install(struct tty_driver *driver, struct tty_struct *tty) { SLMP_INFO *info; - int retval, line; - unsigned long flags; + int line = tty->index; - line = tty->index; if (line >= synclinkmp_device_count) { printk("%s(%d): open with invalid line #%d.\n", __FILE__,__LINE__,line); @@ -727,17 +723,30 @@ static int open(struct tty_struct *tty, struct file *filp) } info = synclinkmp_device_list; - while(info && info->line != line) + while (info && info->line != line) info = info->next_device; if (sanity_check(info, tty->name, "open")) return -ENODEV; - if ( info->init_error ) { + if (info->init_error) { printk("%s(%d):%s device is not allocated, init error=%d\n", - __FILE__,__LINE__,info->device_name,info->init_error); + __FILE__, __LINE__, info->device_name, + info->init_error); return -ENODEV; } tty->driver_data = info; + + return tty_port_install(&info->port, driver, tty); +} + +/* Called when a port is opened. Init and enable port. + */ +static int open(struct tty_struct *tty, struct file *filp) +{ + SLMP_INFO *info = tty->driver_data; + unsigned long flags; + int retval; + info->port.tty = tty; if (debug_level >= DEBUG_LEVEL_INFO) @@ -873,7 +882,7 @@ static void set_termios(struct tty_struct *tty, struct ktermios *old_termios) /* Handle transition to B0 status */ if (old_termios->c_cflag & CBAUD && - !(tty->termios->c_cflag & CBAUD)) { + !(tty->termios.c_cflag & CBAUD)) { info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR); spin_lock_irqsave(&info->lock,flags); set_signals(info); @@ -882,9 +891,9 @@ static void set_termios(struct tty_struct *tty, struct ktermios *old_termios) /* Handle transition away from B0 status */ if (!(old_termios->c_cflag & CBAUD) && - tty->termios->c_cflag & CBAUD) { + tty->termios.c_cflag & CBAUD) { info->serial_signals |= SerialSignal_DTR; - if (!(tty->termios->c_cflag & CRTSCTS) || + if (!(tty->termios.c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags)) { info->serial_signals |= SerialSignal_RTS; } @@ -895,7 +904,7 @@ static void set_termios(struct tty_struct *tty, struct ktermios *old_termios) /* Handle turning off CRTSCTS */ if (old_termios->c_cflag & CRTSCTS && - !(tty->termios->c_cflag & CRTSCTS)) { + !(tty->termios.c_cflag & CRTSCTS)) { tty->hw_stopped = 0; tx_release(tty); } @@ -1473,7 +1482,7 @@ static void throttle(struct tty_struct * tty) if (I_IXOFF(tty)) send_xchar(tty, STOP_CHAR(tty)); - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { spin_lock_irqsave(&info->lock,flags); info->serial_signals &= ~SerialSignal_RTS; set_signals(info); @@ -1502,7 +1511,7 @@ static void unthrottle(struct tty_struct * tty) send_xchar(tty, START_CHAR(tty)); } - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { spin_lock_irqsave(&info->lock,flags); info->serial_signals |= SerialSignal_RTS; set_signals(info); @@ -2708,7 +2717,7 @@ static void shutdown(SLMP_INFO * info) reset_port(info); - if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) { + if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) { info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS); set_signals(info); } @@ -2749,7 +2758,7 @@ static void program_hw(SLMP_INFO *info) get_signals(info); - if (info->netcount || (info->port.tty && info->port.tty->termios->c_cflag & CREAD) ) + if (info->netcount || (info->port.tty && info->port.tty->termios.c_cflag & CREAD) ) rx_start(info); spin_unlock_irqrestore(&info->lock,flags); @@ -2762,14 +2771,14 @@ static void change_params(SLMP_INFO *info) unsigned cflag; int bits_per_char; - if (!info->port.tty || !info->port.tty->termios) + if (!info->port.tty) return; if (debug_level >= DEBUG_LEVEL_INFO) printk("%s(%d):%s change_params()\n", __FILE__,__LINE__, info->device_name ); - cflag = info->port.tty->termios->c_cflag; + cflag = info->port.tty->termios.c_cflag; /* if B0 rate (hangup) specified then negate DTR and RTS */ /* otherwise assert DTR and RTS */ @@ -3306,7 +3315,7 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp, return 0; } - if (tty->termios->c_cflag & CLOCAL) + if (tty->termios.c_cflag & CLOCAL) do_clocal = true; /* Wait for carrier detect and the line to become @@ -3332,7 +3341,7 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp, port->blocked_open++; while (1) { - if (tty->termios->c_cflag & CBAUD) + if (tty->termios.c_cflag & CBAUD) tty_port_raise_dtr_rts(port); set_current_state(TASK_INTERRUPTIBLE); @@ -3357,9 +3366,9 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp, printk("%s(%d):%s block_til_ready() count=%d\n", __FILE__,__LINE__, tty->driver->name, port->count ); - tty_unlock(); + tty_unlock(tty); schedule(); - tty_lock(); + tty_lock(tty); } set_current_state(TASK_RUNNING); @@ -3881,6 +3890,7 @@ static void device_init(int adapter_num, struct pci_dev *pdev) } static const struct tty_operations ops = { + .install = install, .open = open, .close = close, .write = write, diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c index b425c79675ad..41e42f13a214 100644 --- a/drivers/tty/tty_io.c +++ b/drivers/tty/tty_io.c @@ -181,10 +181,13 @@ struct tty_struct *alloc_tty_struct(void) void free_tty_struct(struct tty_struct *tty) { + if (!tty) + return; if (tty->dev) put_device(tty->dev); kfree(tty->write_buf); tty_buffer_free_all(tty); + tty->magic = 0xDEADDEAD; kfree(tty); } @@ -573,7 +576,7 @@ void __tty_hangup(struct tty_struct *tty) } spin_unlock(&redirect_lock); - tty_lock(); + tty_lock(tty); /* some functions below drop BTM, so we need this bit */ set_bit(TTY_HUPPING, &tty->flags); @@ -666,7 +669,7 @@ void __tty_hangup(struct tty_struct *tty) clear_bit(TTY_HUPPING, &tty->flags); tty_ldisc_enable(tty); - tty_unlock(); + tty_unlock(tty); if (f) fput(f); @@ -1103,12 +1106,12 @@ void tty_write_message(struct tty_struct *tty, char *msg) { if (tty) { mutex_lock(&tty->atomic_write_lock); - tty_lock(); + tty_lock(tty); if (tty->ops->write && !test_bit(TTY_CLOSING, &tty->flags)) { - tty_unlock(); + tty_unlock(tty); tty->ops->write(tty, msg, strlen(msg)); } else - tty_unlock(); + tty_unlock(tty); tty_write_unlock(tty); } return; @@ -1213,7 +1216,10 @@ static void pty_line_name(struct tty_driver *driver, int index, char *p) */ static void tty_line_name(struct tty_driver *driver, int index, char *p) { - sprintf(p, "%s%d", driver->name, index + driver->name_base); + if (driver->flags & TTY_DRIVER_UNNUMBERED_NODE) + strcpy(p, driver->name); + else + sprintf(p, "%s%d", driver->name, index + driver->name_base); } /** @@ -1249,21 +1255,19 @@ int tty_init_termios(struct tty_struct *tty) struct ktermios *tp; int idx = tty->index; - tp = tty->driver->termios[idx]; - if (tp == NULL) { - tp = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL); - if (tp == NULL) - return -ENOMEM; - memcpy(tp, &tty->driver->init_termios, - sizeof(struct ktermios)); - tty->driver->termios[idx] = tp; + if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) + tty->termios = tty->driver->init_termios; + else { + /* Check for lazy saved data */ + tp = tty->driver->termios[idx]; + if (tp != NULL) + tty->termios = *tp; + else + tty->termios = tty->driver->init_termios; } - tty->termios = tp; - tty->termios_locked = tp + 1; - /* Compatibility until drivers always set this */ - tty->termios->c_ispeed = tty_termios_input_baud_rate(tty->termios); - tty->termios->c_ospeed = tty_termios_baud_rate(tty->termios); + tty->termios.c_ispeed = tty_termios_input_baud_rate(&tty->termios); + tty->termios.c_ospeed = tty_termios_baud_rate(&tty->termios); return 0; } EXPORT_SYMBOL_GPL(tty_init_termios); @@ -1403,10 +1407,18 @@ struct tty_struct *tty_init_dev(struct tty_driver *driver, int idx) } initialize_tty_struct(tty, driver, idx); + tty_lock(tty); retval = tty_driver_install_tty(driver, tty); if (retval < 0) goto err_deinit_tty; + if (!tty->port) + tty->port = driver->ports[idx]; + + WARN_RATELIMIT(!tty->port, + "%s: %s driver does not set tty->port. This will crash the kernel later. Fix the driver!\n", + __func__, tty->driver->name); + /* * Structures all installed ... call the ldisc open routines. * If we fail here just call release_tty to clean up. No need @@ -1415,9 +1427,11 @@ struct tty_struct *tty_init_dev(struct tty_driver *driver, int idx) retval = tty_ldisc_setup(tty, tty->link); if (retval) goto err_release_tty; + /* Return the tty locked so that it cannot vanish under the caller */ return tty; err_deinit_tty: + tty_unlock(tty); deinitialize_tty_struct(tty); free_tty_struct(tty); err_module_put: @@ -1426,6 +1440,7 @@ err_module_put: /* call the tty release_tty routine to clean out this slot */ err_release_tty: + tty_unlock(tty); printk_ratelimited(KERN_INFO "tty_init_dev: ldisc open failed, " "clearing slot %d\n", idx); release_tty(tty, idx); @@ -1436,22 +1451,25 @@ void tty_free_termios(struct tty_struct *tty) { struct ktermios *tp; int idx = tty->index; - /* Kill this flag and push into drivers for locking etc */ - if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) { - /* FIXME: Locking on ->termios array */ - tp = tty->termios; - tty->driver->termios[idx] = NULL; - kfree(tp); + + /* If the port is going to reset then it has no termios to save */ + if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) + return; + + /* Stash the termios data */ + tp = tty->driver->termios[idx]; + if (tp == NULL) { + tp = kmalloc(sizeof(struct ktermios), GFP_KERNEL); + if (tp == NULL) { + pr_warn("tty: no memory to save termios state.\n"); + return; + } + tty->driver->termios[idx] = tp; } + *tp = tty->termios; } EXPORT_SYMBOL(tty_free_termios); -void tty_shutdown(struct tty_struct *tty) -{ - tty_driver_remove_tty(tty->driver, tty); - tty_free_termios(tty); -} -EXPORT_SYMBOL(tty_shutdown); /** * release_one_tty - release tty structure memory @@ -1462,7 +1480,6 @@ EXPORT_SYMBOL(tty_shutdown); * in use. It also gets called when setup of a device fails. * * Locking: - * tty_mutex - sometimes only * takes the file list lock internally when working on the list * of ttys that the driver keeps. * @@ -1495,11 +1512,6 @@ static void queue_release_one_tty(struct kref *kref) { struct tty_struct *tty = container_of(kref, struct tty_struct, kref); - if (tty->ops->shutdown) - tty->ops->shutdown(tty); - else - tty_shutdown(tty); - /* The hangup queue is now free so we can reuse it rather than waste a chunk of memory for each port */ INIT_WORK(&tty->hangup_work, release_one_tty); @@ -1528,16 +1540,20 @@ EXPORT_SYMBOL(tty_kref_put); * and decrement the refcount of the backing module. * * Locking: - * tty_mutex - sometimes only + * tty_mutex * takes the file list lock internally when working on the list * of ttys that the driver keeps. - * FIXME: should we require tty_mutex is held here ?? * */ static void release_tty(struct tty_struct *tty, int idx) { /* This should always be true but check for the moment */ WARN_ON(tty->index != idx); + WARN_ON(!mutex_is_locked(&tty_mutex)); + if (tty->ops->shutdown) + tty->ops->shutdown(tty); + tty_free_termios(tty); + tty_driver_remove_tty(tty->driver, tty); if (tty->link) tty_kref_put(tty->link); @@ -1572,22 +1588,12 @@ static int tty_release_checks(struct tty_struct *tty, struct tty_struct *o_tty, __func__, idx, tty->name); return -1; } - if (tty->termios != tty->driver->termios[idx]) { - printk(KERN_DEBUG "%s: driver.termios[%d] not termios for (%s)\n", - __func__, idx, tty->name); - return -1; - } if (tty->driver->other) { if (o_tty != tty->driver->other->ttys[idx]) { printk(KERN_DEBUG "%s: other->table[%d] not o_tty for (%s)\n", __func__, idx, tty->name); return -1; } - if (o_tty->termios != tty->driver->other->termios[idx]) { - printk(KERN_DEBUG "%s: other->termios[%d] not o_termios for (%s)\n", - __func__, idx, tty->name); - return -1; - } if (o_tty->link != tty) { printk(KERN_DEBUG "%s: bad pty pointers\n", __func__); return -1; @@ -1628,7 +1634,7 @@ int tty_release(struct inode *inode, struct file *filp) if (tty_paranoia_check(tty, inode, __func__)) return 0; - tty_lock(); + tty_lock(tty); check_tty_count(tty, __func__); __tty_fasync(-1, filp, 0); @@ -1637,10 +1643,11 @@ int tty_release(struct inode *inode, struct file *filp) pty_master = (tty->driver->type == TTY_DRIVER_TYPE_PTY && tty->driver->subtype == PTY_TYPE_MASTER); devpts = (tty->driver->flags & TTY_DRIVER_DEVPTS_MEM) != 0; + /* Review: parallel close */ o_tty = tty->link; if (tty_release_checks(tty, o_tty, idx)) { - tty_unlock(); + tty_unlock(tty); return 0; } @@ -1652,7 +1659,7 @@ int tty_release(struct inode *inode, struct file *filp) if (tty->ops->close) tty->ops->close(tty, filp); - tty_unlock(); + tty_unlock(tty); /* * Sanity check: if tty->count is going to zero, there shouldn't be * any waiters on tty->read_wait or tty->write_wait. We test the @@ -1675,7 +1682,7 @@ int tty_release(struct inode *inode, struct file *filp) opens on /dev/tty */ mutex_lock(&tty_mutex); - tty_lock(); + tty_lock_pair(tty, o_tty); tty_closing = tty->count <= 1; o_tty_closing = o_tty && (o_tty->count <= (pty_master ? 1 : 0)); @@ -1706,7 +1713,7 @@ int tty_release(struct inode *inode, struct file *filp) printk(KERN_WARNING "%s: %s: read/write wait queue active!\n", __func__, tty_name(tty, buf)); - tty_unlock(); + tty_unlock_pair(tty, o_tty); mutex_unlock(&tty_mutex); schedule(); } @@ -1715,6 +1722,9 @@ int tty_release(struct inode *inode, struct file *filp) * The closing flags are now consistent with the open counts on * both sides, and we've completed the last operation that could * block, so it's safe to proceed with closing. + * + * We must *not* drop the tty_mutex until we ensure that a further + * entry into tty_open can not pick up this tty. */ if (pty_master) { if (--o_tty->count < 0) { @@ -1766,12 +1776,13 @@ int tty_release(struct inode *inode, struct file *filp) } mutex_unlock(&tty_mutex); + tty_unlock_pair(tty, o_tty); + /* At this point the TTY_CLOSING flag should ensure a dead tty + cannot be re-opened by a racing opener */ /* check whether both sides are closing ... */ - if (!tty_closing || (o_tty && !o_tty_closing)) { - tty_unlock(); + if (!tty_closing || (o_tty && !o_tty_closing)) return 0; - } #ifdef TTY_DEBUG_HANGUP printk(KERN_DEBUG "%s: freeing tty structure...\n", __func__); @@ -1782,14 +1793,17 @@ int tty_release(struct inode *inode, struct file *filp) tty_ldisc_release(tty, o_tty); /* * The release_tty function takes care of the details of clearing - * the slots and preserving the termios structure. + * the slots and preserving the termios structure. The tty_unlock_pair + * should be safe as we keep a kref while the tty is locked (so the + * unlock never unlocks a freed tty). */ + mutex_lock(&tty_mutex); release_tty(tty, idx); + mutex_unlock(&tty_mutex); /* Make this pty number available for reallocation */ if (devpts) devpts_kill_index(inode, idx); - tty_unlock(); return 0; } @@ -1893,6 +1907,9 @@ static struct tty_driver *tty_lookup_driver(dev_t device, struct file *filp, * Locking: tty_mutex protects tty, tty_lookup_driver and tty_init_dev. * tty->count should protect the rest. * ->siglock protects ->signal/->sighand + * + * Note: the tty_unlock/lock cases without a ref are only safe due to + * tty_mutex */ static int tty_open(struct inode *inode, struct file *filp) @@ -1916,8 +1933,7 @@ retry_open: retval = 0; mutex_lock(&tty_mutex); - tty_lock(); - + /* This is protected by the tty_mutex */ tty = tty_open_current_tty(device, filp); if (IS_ERR(tty)) { retval = PTR_ERR(tty); @@ -1938,17 +1954,19 @@ retry_open: } if (tty) { + tty_lock(tty); retval = tty_reopen(tty); - if (retval) + if (retval < 0) { + tty_unlock(tty); tty = ERR_PTR(retval); - } else + } + } else /* Returns with the tty_lock held for now */ tty = tty_init_dev(driver, index); mutex_unlock(&tty_mutex); if (driver) tty_driver_kref_put(driver); if (IS_ERR(tty)) { - tty_unlock(); retval = PTR_ERR(tty); goto err_file; } @@ -1977,7 +1995,7 @@ retry_open: printk(KERN_DEBUG "%s: error %d in opening %s...\n", __func__, retval, tty->name); #endif - tty_unlock(); /* need to call tty_release without BTM */ + tty_unlock(tty); /* need to call tty_release without BTM */ tty_release(inode, filp); if (retval != -ERESTARTSYS) return retval; @@ -1989,17 +2007,15 @@ retry_open: /* * Need to reset f_op in case a hangup happened. */ - tty_lock(); if (filp->f_op == &hung_up_tty_fops) filp->f_op = &tty_fops; - tty_unlock(); goto retry_open; } - tty_unlock(); + tty_unlock(tty); mutex_lock(&tty_mutex); - tty_lock(); + tty_lock(tty); spin_lock_irq(¤t->sighand->siglock); if (!noctty && current->signal->leader && @@ -2007,11 +2023,10 @@ retry_open: tty->session == NULL) __proc_set_tty(current, tty); spin_unlock_irq(¤t->sighand->siglock); - tty_unlock(); + tty_unlock(tty); mutex_unlock(&tty_mutex); return 0; err_unlock: - tty_unlock(); mutex_unlock(&tty_mutex); /* after locks to avoid deadlock */ if (!IS_ERR_OR_NULL(driver)) @@ -2094,10 +2109,13 @@ out: static int tty_fasync(int fd, struct file *filp, int on) { + struct tty_struct *tty = file_tty(filp); int retval; - tty_lock(); + + tty_lock(tty); retval = __tty_fasync(fd, filp, on); - tty_unlock(); + tty_unlock(tty); + return retval; } @@ -2934,6 +2952,7 @@ void initialize_tty_struct(struct tty_struct *tty, tty->pgrp = NULL; tty->overrun_time = jiffies; tty_buffer_init(tty); + mutex_init(&tty->legacy_mutex); mutex_init(&tty->termios_mutex); mutex_init(&tty->ldisc_mutex); init_waitqueue_head(&tty->write_wait); @@ -2991,6 +3010,15 @@ EXPORT_SYMBOL_GPL(tty_put_char); struct class *tty_class; +static int tty_cdev_add(struct tty_driver *driver, dev_t dev, + unsigned int index, unsigned int count) +{ + /* init here, since reused cdevs cause crashes */ + cdev_init(&driver->cdevs[index], &tty_fops); + driver->cdevs[index].owner = driver->owner; + return cdev_add(&driver->cdevs[index], dev, count); +} + /** * tty_register_device - register a tty device * @driver: the tty driver that describes the tty device @@ -3013,8 +3041,10 @@ struct class *tty_class; struct device *tty_register_device(struct tty_driver *driver, unsigned index, struct device *device) { + struct device *ret; char name[64]; dev_t dev = MKDEV(driver->major, driver->minor_start) + index; + bool cdev = false; if (index >= driver->num) { printk(KERN_ERR "Attempt to register invalid tty line number " @@ -3027,7 +3057,18 @@ struct device *tty_register_device(struct tty_driver *driver, unsigned index, else tty_line_name(driver, index, name); - return device_create(tty_class, device, dev, NULL, name); + if (!(driver->flags & TTY_DRIVER_DYNAMIC_ALLOC)) { + int error = tty_cdev_add(driver, dev, index, 1); + if (error) + return ERR_PTR(error); + cdev = true; + } + + ret = device_create(tty_class, device, dev, NULL, name); + if (IS_ERR(ret) && cdev) + cdev_del(&driver->cdevs[index]); + + return ret; } EXPORT_SYMBOL(tty_register_device); @@ -3046,31 +3087,82 @@ void tty_unregister_device(struct tty_driver *driver, unsigned index) { device_destroy(tty_class, MKDEV(driver->major, driver->minor_start) + index); + if (!(driver->flags & TTY_DRIVER_DYNAMIC_ALLOC)) + cdev_del(&driver->cdevs[index]); } EXPORT_SYMBOL(tty_unregister_device); -struct tty_driver *__alloc_tty_driver(int lines, struct module *owner) +/** + * __tty_alloc_driver -- allocate tty driver + * @lines: count of lines this driver can handle at most + * @owner: module which is repsonsible for this driver + * @flags: some of TTY_DRIVER_* flags, will be set in driver->flags + * + * This should not be called directly, some of the provided macros should be + * used instead. Use IS_ERR and friends on @retval. + */ +struct tty_driver *__tty_alloc_driver(unsigned int lines, struct module *owner, + unsigned long flags) { struct tty_driver *driver; + unsigned int cdevs = 1; + int err; + + if (!lines || (flags & TTY_DRIVER_UNNUMBERED_NODE && lines > 1)) + return ERR_PTR(-EINVAL); driver = kzalloc(sizeof(struct tty_driver), GFP_KERNEL); - if (driver) { - kref_init(&driver->kref); - driver->magic = TTY_DRIVER_MAGIC; - driver->num = lines; - driver->owner = owner; - /* later we'll move allocation of tables here */ + if (!driver) + return ERR_PTR(-ENOMEM); + + kref_init(&driver->kref); + driver->magic = TTY_DRIVER_MAGIC; + driver->num = lines; + driver->owner = owner; + driver->flags = flags; + + if (!(flags & TTY_DRIVER_DEVPTS_MEM)) { + driver->ttys = kcalloc(lines, sizeof(*driver->ttys), + GFP_KERNEL); + driver->termios = kcalloc(lines, sizeof(*driver->termios), + GFP_KERNEL); + if (!driver->ttys || !driver->termios) { + err = -ENOMEM; + goto err_free_all; + } + } + + if (!(flags & TTY_DRIVER_DYNAMIC_ALLOC)) { + driver->ports = kcalloc(lines, sizeof(*driver->ports), + GFP_KERNEL); + if (!driver->ports) { + err = -ENOMEM; + goto err_free_all; + } + cdevs = lines; } + + driver->cdevs = kcalloc(cdevs, sizeof(*driver->cdevs), GFP_KERNEL); + if (!driver->cdevs) { + err = -ENOMEM; + goto err_free_all; + } + return driver; +err_free_all: + kfree(driver->ports); + kfree(driver->ttys); + kfree(driver->termios); + kfree(driver); + return ERR_PTR(err); } -EXPORT_SYMBOL(__alloc_tty_driver); +EXPORT_SYMBOL(__tty_alloc_driver); static void destruct_tty_driver(struct kref *kref) { struct tty_driver *driver = container_of(kref, struct tty_driver, kref); int i; struct ktermios *tp; - void *p; if (driver->flags & TTY_DRIVER_INSTALLED) { /* @@ -3087,13 +3179,14 @@ static void destruct_tty_driver(struct kref *kref) if (!(driver->flags & TTY_DRIVER_DYNAMIC_DEV)) tty_unregister_device(driver, i); } - p = driver->ttys; proc_tty_unregister_driver(driver); - driver->ttys = NULL; - driver->termios = NULL; - kfree(p); - cdev_del(&driver->cdev); + if (driver->flags & TTY_DRIVER_DYNAMIC_ALLOC) + cdev_del(&driver->cdevs[0]); } + kfree(driver->cdevs); + kfree(driver->ports); + kfree(driver->termios); + kfree(driver->ttys); kfree(driver); } @@ -3124,15 +3217,8 @@ int tty_register_driver(struct tty_driver *driver) int error; int i; dev_t dev; - void **p = NULL; struct device *d; - if (!(driver->flags & TTY_DRIVER_DEVPTS_MEM) && driver->num) { - p = kzalloc(driver->num * 2 * sizeof(void *), GFP_KERNEL); - if (!p) - return -ENOMEM; - } - if (!driver->major) { error = alloc_chrdev_region(&dev, driver->minor_start, driver->num, driver->name); @@ -3144,28 +3230,13 @@ int tty_register_driver(struct tty_driver *driver) dev = MKDEV(driver->major, driver->minor_start); error = register_chrdev_region(dev, driver->num, driver->name); } - if (error < 0) { - kfree(p); - return error; - } + if (error < 0) + goto err; - if (p) { - driver->ttys = (struct tty_struct **)p; - driver->termios = (struct ktermios **)(p + driver->num); - } else { - driver->ttys = NULL; - driver->termios = NULL; - } - - cdev_init(&driver->cdev, &tty_fops); - driver->cdev.owner = driver->owner; - error = cdev_add(&driver->cdev, dev, driver->num); - if (error) { - unregister_chrdev_region(dev, driver->num); - driver->ttys = NULL; - driver->termios = NULL; - kfree(p); - return error; + if (driver->flags & TTY_DRIVER_DYNAMIC_ALLOC) { + error = tty_cdev_add(driver, dev, 0, driver->num); + if (error) + goto err_unreg_char; } mutex_lock(&tty_mutex); @@ -3177,7 +3248,7 @@ int tty_register_driver(struct tty_driver *driver) d = tty_register_device(driver, i, NULL); if (IS_ERR(d)) { error = PTR_ERR(d); - goto err; + goto err_unreg_devs; } } } @@ -3185,7 +3256,7 @@ int tty_register_driver(struct tty_driver *driver) driver->flags |= TTY_DRIVER_INSTALLED; return 0; -err: +err_unreg_devs: for (i--; i >= 0; i--) tty_unregister_device(driver, i); @@ -3193,13 +3264,11 @@ err: list_del(&driver->tty_drivers); mutex_unlock(&tty_mutex); +err_unreg_char: unregister_chrdev_region(dev, driver->num); - driver->ttys = NULL; - driver->termios = NULL; - kfree(p); +err: return error; } - EXPORT_SYMBOL(tty_register_driver); /* diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c index a1b9a2f68567..12b1fa0f4f86 100644 --- a/drivers/tty/tty_ioctl.c +++ b/drivers/tty/tty_ioctl.c @@ -410,7 +410,7 @@ EXPORT_SYMBOL_GPL(tty_termios_encode_baud_rate); void tty_encode_baud_rate(struct tty_struct *tty, speed_t ibaud, speed_t obaud) { - tty_termios_encode_baud_rate(tty->termios, ibaud, obaud); + tty_termios_encode_baud_rate(&tty->termios, ibaud, obaud); } EXPORT_SYMBOL_GPL(tty_encode_baud_rate); @@ -427,7 +427,7 @@ EXPORT_SYMBOL_GPL(tty_encode_baud_rate); speed_t tty_get_baud_rate(struct tty_struct *tty) { - speed_t baud = tty_termios_baud_rate(tty->termios); + speed_t baud = tty_termios_baud_rate(&tty->termios); if (baud == 38400 && tty->alt_speed) { if (!tty->warned) { @@ -509,14 +509,14 @@ int tty_set_termios(struct tty_struct *tty, struct ktermios *new_termios) /* FIXME: we need to decide on some locking/ordering semantics for the set_termios notification eventually */ mutex_lock(&tty->termios_mutex); - old_termios = *tty->termios; - *tty->termios = *new_termios; - unset_locked_termios(tty->termios, &old_termios, tty->termios_locked); + old_termios = tty->termios; + tty->termios = *new_termios; + unset_locked_termios(&tty->termios, &old_termios, &tty->termios_locked); /* See if packet mode change of state. */ if (tty->link && tty->link->packet) { int extproc = (old_termios.c_lflag & EXTPROC) | - (tty->termios->c_lflag & EXTPROC); + (tty->termios.c_lflag & EXTPROC); int old_flow = ((old_termios.c_iflag & IXON) && (old_termios.c_cc[VSTOP] == '\023') && (old_termios.c_cc[VSTART] == '\021')); @@ -542,7 +542,7 @@ int tty_set_termios(struct tty_struct *tty, struct ktermios *new_termios) if (tty->ops->set_termios) (*tty->ops->set_termios)(tty, &old_termios); else - tty_termios_copy_hw(tty->termios, &old_termios); + tty_termios_copy_hw(&tty->termios, &old_termios); ld = tty_ldisc_ref(tty); if (ld != NULL) { @@ -578,7 +578,7 @@ static int set_termios(struct tty_struct *tty, void __user *arg, int opt) return retval; mutex_lock(&tty->termios_mutex); - memcpy(&tmp_termios, tty->termios, sizeof(struct ktermios)); + tmp_termios = tty->termios; mutex_unlock(&tty->termios_mutex); if (opt & TERMIOS_TERMIO) { @@ -632,14 +632,14 @@ static int set_termios(struct tty_struct *tty, void __user *arg, int opt) static void copy_termios(struct tty_struct *tty, struct ktermios *kterm) { mutex_lock(&tty->termios_mutex); - memcpy(kterm, tty->termios, sizeof(struct ktermios)); + *kterm = tty->termios; mutex_unlock(&tty->termios_mutex); } static void copy_termios_locked(struct tty_struct *tty, struct ktermios *kterm) { mutex_lock(&tty->termios_mutex); - memcpy(kterm, tty->termios_locked, sizeof(struct ktermios)); + *kterm = tty->termios_locked; mutex_unlock(&tty->termios_mutex); } @@ -707,16 +707,16 @@ static int get_sgflags(struct tty_struct *tty) { int flags = 0; - if (!(tty->termios->c_lflag & ICANON)) { - if (tty->termios->c_lflag & ISIG) + if (!(tty->termios.c_lflag & ICANON)) { + if (tty->termios.c_lflag & ISIG) flags |= 0x02; /* cbreak */ else flags |= 0x20; /* raw */ } - if (tty->termios->c_lflag & ECHO) + if (tty->termios.c_lflag & ECHO) flags |= 0x08; /* echo */ - if (tty->termios->c_oflag & OPOST) - if (tty->termios->c_oflag & ONLCR) + if (tty->termios.c_oflag & OPOST) + if (tty->termios.c_oflag & ONLCR) flags |= 0x10; /* crmod */ return flags; } @@ -726,10 +726,10 @@ static int get_sgttyb(struct tty_struct *tty, struct sgttyb __user *sgttyb) struct sgttyb tmp; mutex_lock(&tty->termios_mutex); - tmp.sg_ispeed = tty->termios->c_ispeed; - tmp.sg_ospeed = tty->termios->c_ospeed; - tmp.sg_erase = tty->termios->c_cc[VERASE]; - tmp.sg_kill = tty->termios->c_cc[VKILL]; + tmp.sg_ispeed = tty->termios.c_ispeed; + tmp.sg_ospeed = tty->termios.c_ospeed; + tmp.sg_erase = tty->termios.c_cc[VERASE]; + tmp.sg_kill = tty->termios.c_cc[VKILL]; tmp.sg_flags = get_sgflags(tty); mutex_unlock(&tty->termios_mutex); @@ -787,7 +787,7 @@ static int set_sgttyb(struct tty_struct *tty, struct sgttyb __user *sgttyb) return -EFAULT; mutex_lock(&tty->termios_mutex); - termios = *tty->termios; + termios = tty->termios; termios.c_cc[VERASE] = tmp.sg_erase; termios.c_cc[VKILL] = tmp.sg_kill; set_sgflags(&termios, tmp.sg_flags); @@ -808,12 +808,12 @@ static int get_tchars(struct tty_struct *tty, struct tchars __user *tchars) struct tchars tmp; mutex_lock(&tty->termios_mutex); - tmp.t_intrc = tty->termios->c_cc[VINTR]; - tmp.t_quitc = tty->termios->c_cc[VQUIT]; - tmp.t_startc = tty->termios->c_cc[VSTART]; - tmp.t_stopc = tty->termios->c_cc[VSTOP]; - tmp.t_eofc = tty->termios->c_cc[VEOF]; - tmp.t_brkc = tty->termios->c_cc[VEOL2]; /* what is brkc anyway? */ + tmp.t_intrc = tty->termios.c_cc[VINTR]; + tmp.t_quitc = tty->termios.c_cc[VQUIT]; + tmp.t_startc = tty->termios.c_cc[VSTART]; + tmp.t_stopc = tty->termios.c_cc[VSTOP]; + tmp.t_eofc = tty->termios.c_cc[VEOF]; + tmp.t_brkc = tty->termios.c_cc[VEOL2]; /* what is brkc anyway? */ mutex_unlock(&tty->termios_mutex); return copy_to_user(tchars, &tmp, sizeof(tmp)) ? -EFAULT : 0; } @@ -825,12 +825,12 @@ static int set_tchars(struct tty_struct *tty, struct tchars __user *tchars) if (copy_from_user(&tmp, tchars, sizeof(tmp))) return -EFAULT; mutex_lock(&tty->termios_mutex); - tty->termios->c_cc[VINTR] = tmp.t_intrc; - tty->termios->c_cc[VQUIT] = tmp.t_quitc; - tty->termios->c_cc[VSTART] = tmp.t_startc; - tty->termios->c_cc[VSTOP] = tmp.t_stopc; - tty->termios->c_cc[VEOF] = tmp.t_eofc; - tty->termios->c_cc[VEOL2] = tmp.t_brkc; /* what is brkc anyway? */ + tty->termios.c_cc[VINTR] = tmp.t_intrc; + tty->termios.c_cc[VQUIT] = tmp.t_quitc; + tty->termios.c_cc[VSTART] = tmp.t_startc; + tty->termios.c_cc[VSTOP] = tmp.t_stopc; + tty->termios.c_cc[VEOF] = tmp.t_eofc; + tty->termios.c_cc[VEOL2] = tmp.t_brkc; /* what is brkc anyway? */ mutex_unlock(&tty->termios_mutex); return 0; } @@ -842,14 +842,14 @@ static int get_ltchars(struct tty_struct *tty, struct ltchars __user *ltchars) struct ltchars tmp; mutex_lock(&tty->termios_mutex); - tmp.t_suspc = tty->termios->c_cc[VSUSP]; + tmp.t_suspc = tty->termios.c_cc[VSUSP]; /* what is dsuspc anyway? */ - tmp.t_dsuspc = tty->termios->c_cc[VSUSP]; - tmp.t_rprntc = tty->termios->c_cc[VREPRINT]; + tmp.t_dsuspc = tty->termios.c_cc[VSUSP]; + tmp.t_rprntc = tty->termios.c_cc[VREPRINT]; /* what is flushc anyway? */ - tmp.t_flushc = tty->termios->c_cc[VEOL2]; - tmp.t_werasc = tty->termios->c_cc[VWERASE]; - tmp.t_lnextc = tty->termios->c_cc[VLNEXT]; + tmp.t_flushc = tty->termios.c_cc[VEOL2]; + tmp.t_werasc = tty->termios.c_cc[VWERASE]; + tmp.t_lnextc = tty->termios.c_cc[VLNEXT]; mutex_unlock(&tty->termios_mutex); return copy_to_user(ltchars, &tmp, sizeof(tmp)) ? -EFAULT : 0; } @@ -862,14 +862,14 @@ static int set_ltchars(struct tty_struct *tty, struct ltchars __user *ltchars) return -EFAULT; mutex_lock(&tty->termios_mutex); - tty->termios->c_cc[VSUSP] = tmp.t_suspc; + tty->termios.c_cc[VSUSP] = tmp.t_suspc; /* what is dsuspc anyway? */ - tty->termios->c_cc[VEOL2] = tmp.t_dsuspc; - tty->termios->c_cc[VREPRINT] = tmp.t_rprntc; + tty->termios.c_cc[VEOL2] = tmp.t_dsuspc; + tty->termios.c_cc[VREPRINT] = tmp.t_rprntc; /* what is flushc anyway? */ - tty->termios->c_cc[VEOL2] = tmp.t_flushc; - tty->termios->c_cc[VWERASE] = tmp.t_werasc; - tty->termios->c_cc[VLNEXT] = tmp.t_lnextc; + tty->termios.c_cc[VEOL2] = tmp.t_flushc; + tty->termios.c_cc[VWERASE] = tmp.t_werasc; + tty->termios.c_cc[VLNEXT] = tmp.t_lnextc; mutex_unlock(&tty->termios_mutex); return 0; } @@ -920,12 +920,12 @@ static int tty_change_softcar(struct tty_struct *tty, int arg) struct ktermios old; mutex_lock(&tty->termios_mutex); - old = *tty->termios; - tty->termios->c_cflag &= ~CLOCAL; - tty->termios->c_cflag |= bit; + old = tty->termios; + tty->termios.c_cflag &= ~CLOCAL; + tty->termios.c_cflag |= bit; if (tty->ops->set_termios) tty->ops->set_termios(tty, &old); - if ((tty->termios->c_cflag & CLOCAL) != bit) + if ((tty->termios.c_cflag & CLOCAL) != bit) ret = -EINVAL; mutex_unlock(&tty->termios_mutex); return ret; @@ -1031,7 +1031,7 @@ int tty_mode_ioctl(struct tty_struct *tty, struct file *file, (struct termios __user *) arg)) return -EFAULT; mutex_lock(&real_tty->termios_mutex); - memcpy(real_tty->termios_locked, &kterm, sizeof(struct ktermios)); + real_tty->termios_locked = kterm; mutex_unlock(&real_tty->termios_mutex); return 0; #else @@ -1048,7 +1048,7 @@ int tty_mode_ioctl(struct tty_struct *tty, struct file *file, (struct termios __user *) arg)) return -EFAULT; mutex_lock(&real_tty->termios_mutex); - memcpy(real_tty->termios_locked, &kterm, sizeof(struct ktermios)); + real_tty->termios_locked = kterm; mutex_unlock(&real_tty->termios_mutex); return ret; #endif diff --git a/drivers/tty/tty_ldisc.c b/drivers/tty/tty_ldisc.c index 6f99c9959f0c..4d7b56268c79 100644 --- a/drivers/tty/tty_ldisc.c +++ b/drivers/tty/tty_ldisc.c @@ -413,7 +413,7 @@ EXPORT_SYMBOL_GPL(tty_ldisc_flush); static void tty_set_termios_ldisc(struct tty_struct *tty, int num) { mutex_lock(&tty->termios_mutex); - tty->termios->c_line = num; + tty->termios.c_line = num; mutex_unlock(&tty->termios_mutex); } @@ -568,7 +568,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) if (IS_ERR(new_ldisc)) return PTR_ERR(new_ldisc); - tty_lock(); + tty_lock(tty); /* * We need to look at the tty locking here for pty/tty pairs * when both sides try to change in parallel. @@ -582,12 +582,12 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) */ if (tty->ldisc->ops->num == ldisc) { - tty_unlock(); + tty_unlock(tty); tty_ldisc_put(new_ldisc); return 0; } - tty_unlock(); + tty_unlock(tty); /* * Problem: What do we do if this blocks ? * We could deadlock here @@ -595,7 +595,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) tty_wait_until_sent(tty, 0); - tty_lock(); + tty_lock(tty); mutex_lock(&tty->ldisc_mutex); /* @@ -605,10 +605,10 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) while (test_bit(TTY_LDISC_CHANGING, &tty->flags)) { mutex_unlock(&tty->ldisc_mutex); - tty_unlock(); + tty_unlock(tty); wait_event(tty_ldisc_wait, test_bit(TTY_LDISC_CHANGING, &tty->flags) == 0); - tty_lock(); + tty_lock(tty); mutex_lock(&tty->ldisc_mutex); } @@ -623,7 +623,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) o_ldisc = tty->ldisc; - tty_unlock(); + tty_unlock(tty); /* * Make sure we don't change while someone holds a * reference to the line discipline. The TTY_LDISC bit @@ -650,7 +650,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) retval = tty_ldisc_wait_idle(tty, 5 * HZ); - tty_lock(); + tty_lock(tty); mutex_lock(&tty->ldisc_mutex); /* handle wait idle failure locked */ @@ -665,7 +665,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) clear_bit(TTY_LDISC_CHANGING, &tty->flags); mutex_unlock(&tty->ldisc_mutex); tty_ldisc_put(new_ldisc); - tty_unlock(); + tty_unlock(tty); return -EIO; } @@ -708,7 +708,7 @@ enable: if (o_work) schedule_work(&o_tty->buf.work); mutex_unlock(&tty->ldisc_mutex); - tty_unlock(); + tty_unlock(tty); return retval; } @@ -722,9 +722,9 @@ enable: static void tty_reset_termios(struct tty_struct *tty) { mutex_lock(&tty->termios_mutex); - *tty->termios = tty->driver->init_termios; - tty->termios->c_ispeed = tty_termios_input_baud_rate(tty->termios); - tty->termios->c_ospeed = tty_termios_baud_rate(tty->termios); + tty->termios = tty->driver->init_termios; + tty->termios.c_ispeed = tty_termios_input_baud_rate(&tty->termios); + tty->termios.c_ospeed = tty_termios_baud_rate(&tty->termios); mutex_unlock(&tty->termios_mutex); } @@ -816,11 +816,11 @@ void tty_ldisc_hangup(struct tty_struct *tty) * need to wait for another function taking the BTM */ clear_bit(TTY_LDISC, &tty->flags); - tty_unlock(); + tty_unlock(tty); cancel_work_sync(&tty->buf.work); mutex_unlock(&tty->ldisc_mutex); retry: - tty_lock(); + tty_lock(tty); mutex_lock(&tty->ldisc_mutex); /* At this point we have a closed ldisc and we want to @@ -831,7 +831,7 @@ retry: if (atomic_read(&tty->ldisc->users) != 1) { char cur_n[TASK_COMM_LEN], tty_n[64]; long timeout = 3 * HZ; - tty_unlock(); + tty_unlock(tty); while (tty_ldisc_wait_idle(tty, timeout) == -EBUSY) { timeout = MAX_SCHEDULE_TIMEOUT; @@ -846,7 +846,7 @@ retry: if (reset == 0) { - if (!tty_ldisc_reinit(tty, tty->termios->c_line)) + if (!tty_ldisc_reinit(tty, tty->termios.c_line)) err = tty_ldisc_open(tty, tty->ldisc); else err = 1; @@ -894,6 +894,23 @@ int tty_ldisc_setup(struct tty_struct *tty, struct tty_struct *o_tty) tty_ldisc_enable(tty); return 0; } + +static void tty_ldisc_kill(struct tty_struct *tty) +{ + mutex_lock(&tty->ldisc_mutex); + /* + * Now kill off the ldisc + */ + tty_ldisc_close(tty, tty->ldisc); + tty_ldisc_put(tty->ldisc); + /* Force an oops if we mess this up */ + tty->ldisc = NULL; + + /* Ensure the next open requests the N_TTY ldisc */ + tty_set_termios_ldisc(tty, N_TTY); + mutex_unlock(&tty->ldisc_mutex); +} + /** * tty_ldisc_release - release line discipline * @tty: tty being shut down @@ -912,28 +929,21 @@ void tty_ldisc_release(struct tty_struct *tty, struct tty_struct *o_tty) * race with the set_ldisc code path. */ - tty_unlock(); + tty_lock_pair(tty, o_tty); tty_ldisc_halt(tty); tty_ldisc_flush_works(tty); - tty_lock(); - - mutex_lock(&tty->ldisc_mutex); - /* - * Now kill off the ldisc - */ - tty_ldisc_close(tty, tty->ldisc); - tty_ldisc_put(tty->ldisc); - /* Force an oops if we mess this up */ - tty->ldisc = NULL; - - /* Ensure the next open requests the N_TTY ldisc */ - tty_set_termios_ldisc(tty, N_TTY); - mutex_unlock(&tty->ldisc_mutex); + if (o_tty) { + tty_ldisc_halt(o_tty); + tty_ldisc_flush_works(o_tty); + } /* This will need doing differently if we need to lock */ + tty_ldisc_kill(tty); + if (o_tty) - tty_ldisc_release(o_tty, NULL); + tty_ldisc_kill(o_tty); + tty_unlock_pair(tty, o_tty); /* And the memory resources remaining (buffers, termios) will be disposed of when the kref hits zero */ } diff --git a/drivers/tty/tty_mutex.c b/drivers/tty/tty_mutex.c index 9ff986c32a21..67feac9e6ebb 100644 --- a/drivers/tty/tty_mutex.c +++ b/drivers/tty/tty_mutex.c @@ -4,29 +4,70 @@ #include <linux/semaphore.h> #include <linux/sched.h> -/* - * The 'big tty mutex' - * - * This mutex is taken and released by tty_lock() and tty_unlock(), - * replacing the older big kernel lock. - * It can no longer be taken recursively, and does not get - * released implicitly while sleeping. - * - * Don't use in new code. - */ -static DEFINE_MUTEX(big_tty_mutex); +/* Legacy tty mutex glue */ + +enum { + TTY_MUTEX_NORMAL, + TTY_MUTEX_NESTED, +}; /* * Getting the big tty mutex. */ -void __lockfunc tty_lock(void) + +static void __lockfunc tty_lock_nested(struct tty_struct *tty, + unsigned int subclass) { - mutex_lock(&big_tty_mutex); + if (tty->magic != TTY_MAGIC) { + printk(KERN_ERR "L Bad %p\n", tty); + WARN_ON(1); + return; + } + tty_kref_get(tty); + mutex_lock_nested(&tty->legacy_mutex, subclass); +} + +void __lockfunc tty_lock(struct tty_struct *tty) +{ + return tty_lock_nested(tty, TTY_MUTEX_NORMAL); } EXPORT_SYMBOL(tty_lock); -void __lockfunc tty_unlock(void) +void __lockfunc tty_unlock(struct tty_struct *tty) { - mutex_unlock(&big_tty_mutex); + if (tty->magic != TTY_MAGIC) { + printk(KERN_ERR "U Bad %p\n", tty); + WARN_ON(1); + return; + } + mutex_unlock(&tty->legacy_mutex); + tty_kref_put(tty); } EXPORT_SYMBOL(tty_unlock); + +/* + * Getting the big tty mutex for a pair of ttys with lock ordering + * On a non pty/tty pair tty2 can be NULL which is just fine. + */ +void __lockfunc tty_lock_pair(struct tty_struct *tty, + struct tty_struct *tty2) +{ + if (tty < tty2) { + tty_lock(tty); + tty_lock_nested(tty2, TTY_MUTEX_NESTED); + } else { + if (tty2 && tty2 != tty) + tty_lock(tty2); + tty_lock_nested(tty, TTY_MUTEX_NESTED); + } +} +EXPORT_SYMBOL(tty_lock_pair); + +void __lockfunc tty_unlock_pair(struct tty_struct *tty, + struct tty_struct *tty2) +{ + tty_unlock(tty); + if (tty2 && tty2 != tty) + tty_unlock(tty2); +} +EXPORT_SYMBOL(tty_unlock_pair); diff --git a/drivers/tty/tty_port.c b/drivers/tty/tty_port.c index bf6e238146ae..96302f4c7079 100644 --- a/drivers/tty/tty_port.c +++ b/drivers/tty/tty_port.c @@ -33,6 +33,46 @@ void tty_port_init(struct tty_port *port) } EXPORT_SYMBOL(tty_port_init); +/** + * tty_port_link_device - link tty and tty_port + * @port: tty_port of the device + * @driver: tty_driver for this device + * @index: index of the tty + * + * Provide the tty layer wit ha link from a tty (specified by @index) to a + * tty_port (@port). Use this only if neither tty_port_register_device nor + * tty_port_install is used in the driver. If used, this has to be called before + * tty_register_driver. + */ +void tty_port_link_device(struct tty_port *port, + struct tty_driver *driver, unsigned index) +{ + if (WARN_ON(index >= driver->num)) + return; + driver->ports[index] = port; +} +EXPORT_SYMBOL_GPL(tty_port_link_device); + +/** + * tty_port_register_device - register tty device + * @port: tty_port of the device + * @driver: tty_driver for this device + * @index: index of the tty + * @device: parent if exists, otherwise NULL + * + * It is the same as tty_register_device except the provided @port is linked to + * a concrete tty specified by @index. Use this or tty_port_install (or both). + * Call tty_port_link_device as a last resort. + */ +struct device *tty_port_register_device(struct tty_port *port, + struct tty_driver *driver, unsigned index, + struct device *device) +{ + tty_port_link_device(port, driver, index); + return tty_register_device(driver, index, device); +} +EXPORT_SYMBOL_GPL(tty_port_register_device); + int tty_port_alloc_xmit_buf(struct tty_port *port) { /* We may sleep in get_zeroed_page() */ @@ -230,7 +270,7 @@ int tty_port_block_til_ready(struct tty_port *port, /* block if port is in the process of being closed */ if (tty_hung_up_p(filp) || port->flags & ASYNC_CLOSING) { - wait_event_interruptible_tty(port->close_wait, + wait_event_interruptible_tty(tty, port->close_wait, !(port->flags & ASYNC_CLOSING)); if (port->flags & ASYNC_HUP_NOTIFY) return -EAGAIN; @@ -246,7 +286,7 @@ int tty_port_block_til_ready(struct tty_port *port, } if (filp->f_flags & O_NONBLOCK) { /* Indicate we are open */ - if (tty->termios->c_cflag & CBAUD) + if (tty->termios.c_cflag & CBAUD) tty_port_raise_dtr_rts(port); port->flags |= ASYNC_NORMAL_ACTIVE; return 0; @@ -270,7 +310,7 @@ int tty_port_block_til_ready(struct tty_port *port, while (1) { /* Indicate we are open */ - if (tty->termios->c_cflag & CBAUD) + if (tty->termios.c_cflag & CBAUD) tty_port_raise_dtr_rts(port); prepare_to_wait(&port->open_wait, &wait, TASK_INTERRUPTIBLE); @@ -296,9 +336,9 @@ int tty_port_block_til_ready(struct tty_port *port, retval = -ERESTARTSYS; break; } - tty_unlock(); + tty_unlock(tty); schedule(); - tty_lock(); + tty_lock(tty); } finish_wait(&port->open_wait, &wait); @@ -369,7 +409,7 @@ int tty_port_close_start(struct tty_port *port, /* Drop DTR/RTS if HUPCL is set. This causes any attached modem to hang up the line */ - if (tty->termios->c_cflag & HUPCL) + if (tty->termios.c_cflag & HUPCL) tty_port_lower_dtr_rts(port); /* Don't call port->drop for the last reference. Callers will want @@ -413,6 +453,24 @@ void tty_port_close(struct tty_port *port, struct tty_struct *tty, } EXPORT_SYMBOL(tty_port_close); +/** + * tty_port_install - generic tty->ops->install handler + * @port: tty_port of the device + * @driver: tty_driver for this device + * @tty: tty to be installed + * + * It is the same as tty_standard_install except the provided @port is linked + * to a concrete tty specified by @tty. Use this or tty_port_register_device + * (or both). Call tty_port_link_device as a last resort. + */ +int tty_port_install(struct tty_port *port, struct tty_driver *driver, + struct tty_struct *tty) +{ + tty->port = port; + return tty_standard_install(driver, tty); +} +EXPORT_SYMBOL_GPL(tty_port_install); + int tty_port_open(struct tty_port *port, struct tty_struct *tty, struct file *filp) { diff --git a/drivers/tty/vt/keyboard.c b/drivers/tty/vt/keyboard.c index 48cc6f25cfd3..681765baef69 100644 --- a/drivers/tty/vt/keyboard.c +++ b/drivers/tty/vt/keyboard.c @@ -119,6 +119,7 @@ static const int NR_TYPES = ARRAY_SIZE(max_vals); static struct input_handler kbd_handler; static DEFINE_SPINLOCK(kbd_event_lock); +static DEFINE_SPINLOCK(led_lock); static unsigned long key_down[BITS_TO_LONGS(KEY_CNT)]; /* keyboard key bitmap */ static unsigned char shift_down[NR_SHIFT]; /* shift state counters.. */ static bool dead_key_next; @@ -310,7 +311,7 @@ static void put_queue(struct vc_data *vc, int ch) if (tty) { tty_insert_flip_char(tty, ch, 0); - con_schedule_flip(tty); + tty_schedule_flip(tty); } } @@ -325,7 +326,7 @@ static void puts_queue(struct vc_data *vc, char *cp) tty_insert_flip_char(tty, *cp, 0); cp++; } - con_schedule_flip(tty); + tty_schedule_flip(tty); } static void applkey(struct vc_data *vc, int key, char mode) @@ -586,7 +587,7 @@ static void fn_send_intr(struct vc_data *vc) if (!tty) return; tty_insert_flip_char(tty, 0, TTY_BREAK); - con_schedule_flip(tty); + tty_schedule_flip(tty); } static void fn_scroll_forw(struct vc_data *vc) @@ -984,7 +985,7 @@ static void k_brl(struct vc_data *vc, unsigned char value, char up_flag) * or (ii) whatever pattern of lights people want to show using KDSETLED, * or (iii) specified bits of specified words in kernel memory. */ -unsigned char getledstate(void) +static unsigned char getledstate(void) { return ledstate; } @@ -992,7 +993,7 @@ unsigned char getledstate(void) void setledstate(struct kbd_struct *kbd, unsigned int led) { unsigned long flags; - spin_lock_irqsave(&kbd_event_lock, flags); + spin_lock_irqsave(&led_lock, flags); if (!(led & ~7)) { ledioctl = led; kbd->ledmode = LED_SHOW_IOCTL; @@ -1000,7 +1001,7 @@ void setledstate(struct kbd_struct *kbd, unsigned int led) kbd->ledmode = LED_SHOW_FLAGS; set_leds(); - spin_unlock_irqrestore(&kbd_event_lock, flags); + spin_unlock_irqrestore(&led_lock, flags); } static inline unsigned char getleds(void) @@ -1049,13 +1050,13 @@ static int kbd_update_leds_helper(struct input_handle *handle, void *data) */ int vt_get_leds(int console, int flag) { - unsigned long flags; struct kbd_struct * kbd = kbd_table + console; int ret; + unsigned long flags; - spin_lock_irqsave(&kbd_event_lock, flags); + spin_lock_irqsave(&led_lock, flags); ret = vc_kbd_led(kbd, flag); - spin_unlock_irqrestore(&kbd_event_lock, flags); + spin_unlock_irqrestore(&led_lock, flags); return ret; } @@ -1091,11 +1092,11 @@ void vt_set_led_state(int console, int leds) void vt_kbd_con_start(int console) { struct kbd_struct * kbd = kbd_table + console; -/* unsigned long flags; */ -/* spin_lock_irqsave(&kbd_event_lock, flags); */ + unsigned long flags; + spin_lock_irqsave(&led_lock, flags); clr_vc_kbd_led(kbd, VC_SCROLLOCK); set_leds(); -/* spin_unlock_irqrestore(&kbd_event_lock, flags); */ + spin_unlock_irqrestore(&led_lock, flags); } /** @@ -1104,21 +1105,15 @@ void vt_kbd_con_start(int console) * * Handle console stop. This is a wrapper for the VT layer * so that we can keep kbd knowledge internal - * - * FIXME: We eventually need to hold the kbd lock here to protect - * the LED updating. We can't do it yet because fn_hold calls stop_tty - * and start_tty under the kbd_event_lock, while normal tty paths - * don't hold the lock. We probably need to split out an LED lock - * but not during an -rc release! */ void vt_kbd_con_stop(int console) { struct kbd_struct * kbd = kbd_table + console; -/* unsigned long flags; */ -/* spin_lock_irqsave(&kbd_event_lock, flags); */ + unsigned long flags; + spin_lock_irqsave(&led_lock, flags); set_vc_kbd_led(kbd, VC_SCROLLOCK); set_leds(); -/* spin_unlock_irqrestore(&kbd_event_lock, flags); */ + spin_unlock_irqrestore(&led_lock, flags); } /* @@ -1130,7 +1125,12 @@ void vt_kbd_con_stop(int console) */ static void kbd_bh(unsigned long dummy) { - unsigned char leds = getleds(); + unsigned char leds; + unsigned long flags; + + spin_lock_irqsave(&led_lock, flags); + leds = getleds(); + spin_unlock_irqrestore(&led_lock, flags); if (leds != ledstate) { input_handler_for_each_handle(&kbd_handler, &leds, @@ -2035,11 +2035,11 @@ int vt_do_kdskled(int console, int cmd, unsigned long arg, int perm) return -EPERM; if (arg & ~0x77) return -EINVAL; - spin_lock_irqsave(&kbd_event_lock, flags); + spin_lock_irqsave(&led_lock, flags); kbd->ledflagstate = (arg & 7); kbd->default_ledflagstate = ((arg >> 4) & 7); set_leds(); - spin_unlock_irqrestore(&kbd_event_lock, flags); + spin_unlock_irqrestore(&led_lock, flags); return 0; /* the ioctls below only set the lights, not the functions */ @@ -2134,8 +2134,10 @@ void vt_reset_keyboard(int console) clr_vc_kbd_mode(kbd, VC_CRLF); kbd->lockstate = 0; kbd->slockstate = 0; + spin_lock(&led_lock); kbd->ledmode = LED_SHOW_FLAGS; kbd->ledflagstate = kbd->default_ledflagstate; + spin_unlock(&led_lock); /* do not do set_leds here because this causes an endless tasklet loop when the keyboard hasn't been initialized yet */ spin_unlock_irqrestore(&kbd_event_lock, flags); diff --git a/drivers/tty/vt/vt.c b/drivers/tty/vt/vt.c index 84cbf298c094..e07ded30fc7f 100644 --- a/drivers/tty/vt/vt.c +++ b/drivers/tty/vt/vt.c @@ -1380,7 +1380,7 @@ static void respond_string(const char *p, struct tty_struct *tty) tty_insert_flip_char(tty, *p, 0); p++; } - con_schedule_flip(tty); + tty_schedule_flip(tty); } static void cursor_report(struct vc_data *vc, struct tty_struct *tty) @@ -2792,41 +2792,52 @@ static void con_flush_chars(struct tty_struct *tty) /* * Allocate the console screen memory. */ -static int con_open(struct tty_struct *tty, struct file *filp) +static int con_install(struct tty_driver *driver, struct tty_struct *tty) { unsigned int currcons = tty->index; - int ret = 0; + struct vc_data *vc; + int ret; console_lock(); - if (tty->driver_data == NULL) { - ret = vc_allocate(currcons); - if (ret == 0) { - struct vc_data *vc = vc_cons[currcons].d; + ret = vc_allocate(currcons); + if (ret) + goto unlock; - /* Still being freed */ - if (vc->port.tty) { - console_unlock(); - return -ERESTARTSYS; - } - tty->driver_data = vc; - vc->port.tty = tty; + vc = vc_cons[currcons].d; - if (!tty->winsize.ws_row && !tty->winsize.ws_col) { - tty->winsize.ws_row = vc_cons[currcons].d->vc_rows; - tty->winsize.ws_col = vc_cons[currcons].d->vc_cols; - } - if (vc->vc_utf) - tty->termios->c_iflag |= IUTF8; - else - tty->termios->c_iflag &= ~IUTF8; - console_unlock(); - return ret; - } + /* Still being freed */ + if (vc->port.tty) { + ret = -ERESTARTSYS; + goto unlock; } + + ret = tty_port_install(&vc->port, driver, tty); + if (ret) + goto unlock; + + tty->driver_data = vc; + vc->port.tty = tty; + + if (!tty->winsize.ws_row && !tty->winsize.ws_col) { + tty->winsize.ws_row = vc_cons[currcons].d->vc_rows; + tty->winsize.ws_col = vc_cons[currcons].d->vc_cols; + } + if (vc->vc_utf) + tty->termios.c_iflag |= IUTF8; + else + tty->termios.c_iflag &= ~IUTF8; +unlock: console_unlock(); return ret; } +static int con_open(struct tty_struct *tty, struct file *filp) +{ + /* everything done in install */ + return 0; +} + + static void con_close(struct tty_struct *tty, struct file *filp) { /* Nothing to do - we defer to shutdown */ @@ -2839,7 +2850,6 @@ static void con_shutdown(struct tty_struct *tty) console_lock(); vc->port.tty = NULL; console_unlock(); - tty_shutdown(tty); } static int default_italic_color = 2; // green (ASCII) @@ -2947,6 +2957,7 @@ static int __init con_init(void) console_initcall(con_init); static const struct tty_operations con_ops = { + .install = con_install, .open = con_open, .close = con_close, .write = con_write, diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index f763ed7ba91e..ff7b5a8d501c 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -826,7 +826,7 @@ static void acm_tty_set_termios(struct tty_struct *tty, struct ktermios *termios_old) { struct acm *acm = tty->driver_data; - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; struct usb_cdc_line_coding newline; int newctrl = acm->ctrlout; @@ -1299,7 +1299,8 @@ skip_countries: usb_set_intfdata(data_interface, acm); usb_get_intf(control_interface); - tty_register_device(acm_tty_driver, minor, &control_interface->dev); + tty_port_register_device(&acm->port, acm_tty_driver, minor, + &control_interface->dev); return 0; alloc_fail7: diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c index 5b3f5fffea92..2b5534c2ab84 100644 --- a/drivers/usb/gadget/u_serial.c +++ b/drivers/usb/gadget/u_serial.c @@ -1129,7 +1129,8 @@ int gserial_setup(struct usb_gadget *g, unsigned count) for (i = 0; i < count; i++) { struct device *tty_dev; - tty_dev = tty_register_device(gs_tty_driver, i, &g->dev); + tty_dev = tty_port_register_device(&ports[i].port->port, + gs_tty_driver, i, &g->dev); if (IS_ERR(tty_dev)) pr_warning("%s: no classdev for port %d, err %ld\n", __func__, i, PTR_ERR(tty_dev)); diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c index f8ce97d8b0ad..3b98fb733362 100644 --- a/drivers/usb/serial/ark3116.c +++ b/drivers/usb/serial/ark3116.c @@ -215,7 +215,7 @@ static void ark3116_release(struct usb_serial *serial) static void ark3116_init_termios(struct tty_struct *tty) { - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; *termios = tty_std_termios; termios->c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL; @@ -229,7 +229,7 @@ static void ark3116_set_termios(struct tty_struct *tty, { struct usb_serial *serial = port->serial; struct ark3116_private *priv = usb_get_serial_port_data(port); - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; unsigned int cflag = termios->c_cflag; int bps = tty_get_baud_rate(tty); int quot; diff --git a/drivers/usb/serial/belkin_sa.c b/drivers/usb/serial/belkin_sa.c index 6b7365632951..a46df73ee96e 100644 --- a/drivers/usb/serial/belkin_sa.c +++ b/drivers/usb/serial/belkin_sa.c @@ -307,7 +307,7 @@ static void belkin_sa_set_termios(struct tty_struct *tty, unsigned long control_state; int bad_flow_control; speed_t baud; - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; iflag = termios->c_iflag; cflag = termios->c_cflag; diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c index b9cca6dcde07..9a564286bfd7 100644 --- a/drivers/usb/serial/console.c +++ b/drivers/usb/serial/console.c @@ -165,8 +165,8 @@ static int usb_console_setup(struct console *co, char *options) } if (serial->type->set_termios) { - tty->termios->c_cflag = cflag; - tty_termios_encode_baud_rate(tty->termios, baud, baud); + tty->termios.c_cflag = cflag; + tty_termios_encode_baud_rate(&tty->termios, baud, baud); memset(&dummy, 0, sizeof(struct ktermios)); serial->type->set_termios(tty, port, &dummy); diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index 1e71079ce33b..ba5e07e188a0 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -469,7 +469,7 @@ static void cp210x_get_termios(struct tty_struct *tty, if (tty) { cp210x_get_termios_port(tty->driver_data, - &tty->termios->c_cflag, &baud); + &tty->termios.c_cflag, &baud); tty_encode_baud_rate(tty, baud, baud); } @@ -631,7 +631,7 @@ static void cp210x_change_speed(struct tty_struct *tty, { u32 baud; - baud = tty->termios->c_ospeed; + baud = tty->termios.c_ospeed; /* This maps the requested rate to a rate valid on cp2102 or cp2103, * or to an arbitrary rate in [1M,2M]. @@ -665,10 +665,10 @@ static void cp210x_set_termios(struct tty_struct *tty, if (!tty) return; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; old_cflag = old_termios->c_cflag; - if (tty->termios->c_ospeed != old_termios->c_ospeed) + if (tty->termios.c_ospeed != old_termios->c_ospeed) cp210x_change_speed(tty, port, old_termios); /* If the number of data bits is to be updated */ diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c index b78c34eb5d3f..be34f153e566 100644 --- a/drivers/usb/serial/cypress_m8.c +++ b/drivers/usb/serial/cypress_m8.c @@ -922,38 +922,38 @@ static void cypress_set_termios(struct tty_struct *tty, early enough */ if (!priv->termios_initialized) { if (priv->chiptype == CT_EARTHMATE) { - *(tty->termios) = tty_std_termios; - tty->termios->c_cflag = B4800 | CS8 | CREAD | HUPCL | + tty->termios = tty_std_termios; + tty->termios.c_cflag = B4800 | CS8 | CREAD | HUPCL | CLOCAL; - tty->termios->c_ispeed = 4800; - tty->termios->c_ospeed = 4800; + tty->termios.c_ispeed = 4800; + tty->termios.c_ospeed = 4800; } else if (priv->chiptype == CT_CYPHIDCOM) { - *(tty->termios) = tty_std_termios; - tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL | + tty->termios = tty_std_termios; + tty->termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL; - tty->termios->c_ispeed = 9600; - tty->termios->c_ospeed = 9600; + tty->termios.c_ispeed = 9600; + tty->termios.c_ospeed = 9600; } else if (priv->chiptype == CT_CA42V2) { - *(tty->termios) = tty_std_termios; - tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL | + tty->termios = tty_std_termios; + tty->termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL; - tty->termios->c_ispeed = 9600; - tty->termios->c_ospeed = 9600; + tty->termios.c_ispeed = 9600; + tty->termios.c_ospeed = 9600; } priv->termios_initialized = 1; } spin_unlock_irqrestore(&priv->lock, flags); /* Unsupported features need clearing */ - tty->termios->c_cflag &= ~(CMSPAR|CRTSCTS); + tty->termios.c_cflag &= ~(CMSPAR|CRTSCTS); - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; + cflag = tty->termios.c_cflag; + iflag = tty->termios.c_iflag; /* check if there are new settings */ if (old_termios) { spin_lock_irqsave(&priv->lock, flags); - priv->tmp_termios = *(tty->termios); + priv->tmp_termios = tty->termios; spin_unlock_irqrestore(&priv->lock, flags); } @@ -1021,7 +1021,7 @@ static void cypress_set_termios(struct tty_struct *tty, "4800bps."); /* define custom termios settings for NMEA protocol */ - tty->termios->c_iflag /* input modes - */ + tty->termios.c_iflag /* input modes - */ &= ~(IGNBRK /* disable ignore break */ | BRKINT /* disable break causes interrupt */ | PARMRK /* disable mark parity errors */ @@ -1031,10 +1031,10 @@ static void cypress_set_termios(struct tty_struct *tty, | ICRNL /* disable translate CR to NL */ | IXON); /* disable enable XON/XOFF flow control */ - tty->termios->c_oflag /* output modes */ + tty->termios.c_oflag /* output modes */ &= ~OPOST; /* disable postprocess output char */ - tty->termios->c_lflag /* line discipline modes */ + tty->termios.c_lflag /* line discipline modes */ &= ~(ECHO /* disable echo input characters */ | ECHONL /* disable echo new line */ | ICANON /* disable erase, kill, werase, and rprnt @@ -1200,7 +1200,7 @@ static void cypress_read_int_callback(struct urb *urb) /* hangup, as defined in acm.c... this might be a bad place for it * though */ - if (tty && !(tty->termios->c_cflag & CLOCAL) && + if (tty && !(tty->termios.c_cflag & CLOCAL) && !(priv->current_status & UART_CD)) { dbg("%s - calling hangup", __func__); tty_hangup(tty); diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c index b5cd838093ef..afd9d2ec577b 100644 --- a/drivers/usb/serial/digi_acceleport.c +++ b/drivers/usb/serial/digi_acceleport.c @@ -687,8 +687,8 @@ static void digi_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { struct digi_port *priv = usb_get_serial_port_data(port); - unsigned int iflag = tty->termios->c_iflag; - unsigned int cflag = tty->termios->c_cflag; + unsigned int iflag = tty->termios.c_iflag; + unsigned int cflag = tty->termios.c_cflag; unsigned int old_iflag = old_termios->c_iflag; unsigned int old_cflag = old_termios->c_cflag; unsigned char buf[32]; @@ -709,7 +709,7 @@ static void digi_set_termios(struct tty_struct *tty, /* don't set RTS if using hardware flow control */ /* and throttling input */ modem_signals = TIOCM_DTR; - if (!(tty->termios->c_cflag & CRTSCTS) || + if (!(tty->termios.c_cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags)) modem_signals |= TIOCM_RTS; digi_set_modem_signals(port, modem_signals, 1); @@ -748,7 +748,7 @@ static void digi_set_termios(struct tty_struct *tty, } } /* set parity */ - tty->termios->c_cflag &= ~CMSPAR; + tty->termios.c_cflag &= ~CMSPAR; if ((cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD))) { if (cflag&PARENB) { @@ -1124,8 +1124,8 @@ static int digi_open(struct tty_struct *tty, struct usb_serial_port *port) /* set termios settings */ if (tty) { - not_termios.c_cflag = ~tty->termios->c_cflag; - not_termios.c_iflag = ~tty->termios->c_iflag; + not_termios.c_cflag = ~tty->termios.c_cflag; + not_termios.c_iflag = ~tty->termios.c_iflag; digi_set_termios(tty, port, ¬_termios); } return 0; @@ -1500,7 +1500,7 @@ static int digi_read_oob_callback(struct urb *urb) rts = 0; if (tty) - rts = tty->termios->c_cflag & CRTSCTS; + rts = tty->termios.c_cflag & CRTSCTS; if (tty && opcode == DIGI_CMD_READ_INPUT_SIGNALS) { spin_lock(&priv->dp_port_lock); diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c index cdf61dd07318..34e86383090a 100644 --- a/drivers/usb/serial/empeg.c +++ b/drivers/usb/serial/empeg.c @@ -87,7 +87,7 @@ static int empeg_startup(struct usb_serial *serial) static void empeg_init_termios(struct tty_struct *tty) { - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; /* * The empeg-car player wants these particular tty settings. diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c index 499b15fd82f1..79451ee12ca0 100644 --- a/drivers/usb/serial/f81232.c +++ b/drivers/usb/serial/f81232.c @@ -173,10 +173,11 @@ static void f81232_set_termios(struct tty_struct *tty, /* FIXME - Stubbed out for now */ /* Don't change anything if nothing has changed */ - if (!tty_termios_hw_change(tty->termios, old_termios)) + if (!tty_termios_hw_change(&tty->termios, old_termios)) return; /* Do the real work here... */ + tty_termios_copy_hw(&tty->termios, old_termios); } static int f81232_tiocmget(struct tty_struct *tty) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 5620db6469e5..24e3e19849a2 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -2082,7 +2082,7 @@ static void ftdi_set_termios(struct tty_struct *tty, { struct usb_device *dev = port->serial->dev; struct ftdi_private *priv = usb_get_serial_port_data(port); - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; unsigned int cflag = termios->c_cflag; __u16 urb_value; /* will hold the new flags */ diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c index e1f5ccd1e8f8..f435575c4e6e 100644 --- a/drivers/usb/serial/io_edgeport.c +++ b/drivers/usb/serial/io_edgeport.c @@ -1458,7 +1458,7 @@ static void edge_throttle(struct tty_struct *tty) } /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { edge_port->shadowMCR &= ~MCR_RTS; status = send_cmd_write_uart_register(edge_port, MCR, edge_port->shadowMCR); @@ -1497,7 +1497,7 @@ static void edge_unthrottle(struct tty_struct *tty) return; } /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { edge_port->shadowMCR |= MCR_RTS; send_cmd_write_uart_register(edge_port, MCR, edge_port->shadowMCR); @@ -1516,9 +1516,9 @@ static void edge_set_termios(struct tty_struct *tty, struct edgeport_port *edge_port = usb_get_serial_port_data(port); unsigned int cflag; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; dbg("%s - clfag %08x iflag %08x", __func__, - tty->termios->c_cflag, tty->termios->c_iflag); + tty->termios.c_cflag, tty->termios.c_iflag); dbg("%s - old clfag %08x old iflag %08x", __func__, old_termios->c_cflag, old_termios->c_iflag); @@ -1987,7 +1987,7 @@ static void process_rcvd_status(struct edgeport_serial *edge_serial, tty = tty_port_tty_get(&edge_port->port->port); if (tty) { change_port_settings(tty, - edge_port, tty->termios); + edge_port, &tty->termios); tty_kref_put(tty); } @@ -2570,7 +2570,7 @@ static void change_port_settings(struct tty_struct *tty, return; } - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; switch (cflag & CSIZE) { case CS5: diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c index 3936904c6419..765978ae752e 100644 --- a/drivers/usb/serial/io_ti.c +++ b/drivers/usb/serial/io_ti.c @@ -1870,7 +1870,7 @@ static int edge_open(struct tty_struct *tty, struct usb_serial_port *port) /* set up the port settings */ if (tty) - edge_set_termios(tty, port, tty->termios); + edge_set_termios(tty, port, &tty->termios); /* open up the port */ @@ -2272,13 +2272,13 @@ static void change_port_settings(struct tty_struct *tty, config = kmalloc (sizeof (*config), GFP_KERNEL); if (!config) { - *tty->termios = *old_termios; + tty->termios = *old_termios; dev_err(&edge_port->port->dev, "%s - out of memory\n", __func__); return; } - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; config->wFlags = 0; @@ -2362,7 +2362,7 @@ static void change_port_settings(struct tty_struct *tty, } else dbg("%s - OUTBOUND XON/XOFF is disabled", __func__); - tty->termios->c_cflag &= ~CMSPAR; + tty->termios.c_cflag &= ~CMSPAR; /* Round the baud rate */ baud = tty_get_baud_rate(tty); @@ -2408,10 +2408,10 @@ static void edge_set_termios(struct tty_struct *tty, struct edgeport_port *edge_port = usb_get_serial_port_data(port); unsigned int cflag; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; dbg("%s - clfag %08x iflag %08x", __func__, - tty->termios->c_cflag, tty->termios->c_iflag); + tty->termios.c_cflag, tty->termios.c_iflag); dbg("%s - old clfag %08x old iflag %08x", __func__, old_termios->c_cflag, old_termios->c_iflag); dbg("%s - port %d", __func__, port->number); diff --git a/drivers/usb/serial/ir-usb.c b/drivers/usb/serial/ir-usb.c index fc09414c960f..5a96692b12a2 100644 --- a/drivers/usb/serial/ir-usb.c +++ b/drivers/usb/serial/ir-usb.c @@ -381,7 +381,7 @@ static void ir_set_termios(struct tty_struct *tty, ir_xbof = ir_xbof_change(xbof) ; /* Only speed changes are supported */ - tty_termios_copy_hw(tty->termios, old_termios); + tty_termios_copy_hw(&tty->termios, old_termios); tty_encode_baud_rate(tty, baud, baud); /* diff --git a/drivers/usb/serial/iuu_phoenix.c b/drivers/usb/serial/iuu_phoenix.c index 22b1eb5040b7..bf3864045c18 100644 --- a/drivers/usb/serial/iuu_phoenix.c +++ b/drivers/usb/serial/iuu_phoenix.c @@ -921,7 +921,7 @@ static void iuu_set_termios(struct tty_struct *tty, { const u32 supported_mask = CMSPAR|PARENB|PARODD; struct iuu_private *priv = usb_get_serial_port_data(port); - unsigned int cflag = tty->termios->c_cflag; + unsigned int cflag = tty->termios.c_cflag; int status; u32 actual; u32 parity; @@ -930,7 +930,7 @@ static void iuu_set_termios(struct tty_struct *tty, u32 newval = cflag & supported_mask; /* Just use the ospeed. ispeed should be the same. */ - baud = tty->termios->c_ospeed; + baud = tty->termios.c_ospeed; dbg("%s - enter c_ospeed or baud=%d", __func__, baud); @@ -961,13 +961,13 @@ static void iuu_set_termios(struct tty_struct *tty, * settings back over and then adjust them */ if (old_termios) - tty_termios_copy_hw(tty->termios, old_termios); + tty_termios_copy_hw(&tty->termios, old_termios); if (status != 0) /* Set failed - return old bits */ return; /* Re-encode speed, parity and csize */ tty_encode_baud_rate(tty, baud, baud); - tty->termios->c_cflag &= ~(supported_mask|CSIZE); - tty->termios->c_cflag |= newval | csize; + tty->termios.c_cflag &= ~(supported_mask|CSIZE); + tty->termios.c_cflag |= newval | csize; } static void iuu_close(struct usb_serial_port *port) @@ -993,14 +993,14 @@ static void iuu_close(struct usb_serial_port *port) static void iuu_init_termios(struct tty_struct *tty) { - *(tty->termios) = tty_std_termios; - tty->termios->c_cflag = CLOCAL | CREAD | CS8 | B9600 + tty->termios = tty_std_termios; + tty->termios.c_cflag = CLOCAL | CREAD | CS8 | B9600 | TIOCM_CTS | CSTOPB | PARENB; - tty->termios->c_ispeed = 9600; - tty->termios->c_ospeed = 9600; - tty->termios->c_lflag = 0; - tty->termios->c_oflag = 0; - tty->termios->c_iflag = 0; + tty->termios.c_ispeed = 9600; + tty->termios.c_ospeed = 9600; + tty->termios.c_lflag = 0; + tty->termios.c_oflag = 0; + tty->termios.c_iflag = 0; } static int iuu_open(struct tty_struct *tty, struct usb_serial_port *port) @@ -1012,8 +1012,8 @@ static int iuu_open(struct tty_struct *tty, struct usb_serial_port *port) u32 actual; struct iuu_private *priv = usb_get_serial_port_data(port); - baud = tty->termios->c_ospeed; - tty->termios->c_ispeed = baud; + baud = tty->termios.c_ospeed; + tty->termios.c_ispeed = baud; /* Re-encode speed */ tty_encode_baud_rate(tty, baud, baud); diff --git a/drivers/usb/serial/keyspan.c b/drivers/usb/serial/keyspan.c index af0b70eaf032..7bcbb47e1449 100644 --- a/drivers/usb/serial/keyspan.c +++ b/drivers/usb/serial/keyspan.c @@ -158,7 +158,7 @@ static void keyspan_set_termios(struct tty_struct *tty, p_priv = usb_get_serial_port_data(port); d_details = p_priv->device_details; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; device_port = port->number - port->serial->minor; /* Baud rate calculation takes baud rate as an integer @@ -179,7 +179,7 @@ static void keyspan_set_termios(struct tty_struct *tty, p_priv->flow_control = (cflag & CRTSCTS) ? flow_cts : flow_none; /* Mark/Space not supported */ - tty->termios->c_cflag &= ~CMSPAR; + tty->termios.c_cflag &= ~CMSPAR; keyspan_send_setup(port, 0); } @@ -1086,7 +1086,7 @@ static int keyspan_open(struct tty_struct *tty, struct usb_serial_port *port) device_port = port->number - port->serial->minor; if (tty) { - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; /* Baud rate calculation takes baud rate as an integer so other rates can be generated if desired. */ baud_rate = tty_get_baud_rate(tty); diff --git a/drivers/usb/serial/keyspan_pda.c b/drivers/usb/serial/keyspan_pda.c index a4ac3cfeffc4..dcada8615fcf 100644 --- a/drivers/usb/serial/keyspan_pda.c +++ b/drivers/usb/serial/keyspan_pda.c @@ -338,7 +338,7 @@ static void keyspan_pda_set_termios(struct tty_struct *tty, 7[EOMS]1: 10 bit, b0/b7 is parity 7[EOMS]2: 11 bit, b0/b7 is parity, extra bit always (mark?) - HW flow control is dictated by the tty->termios->c_cflags & CRTSCTS + HW flow control is dictated by the tty->termios.c_cflags & CRTSCTS bit. For now, just do baud. */ @@ -353,7 +353,7 @@ static void keyspan_pda_set_termios(struct tty_struct *tty, } /* Only speed can change so copy the old h/w parameters then encode the new speed */ - tty_termios_copy_hw(tty->termios, old_termios); + tty_termios_copy_hw(&tty->termios, old_termios); tty_encode_baud_rate(tty, speed, speed); } diff --git a/drivers/usb/serial/kl5kusb105.c b/drivers/usb/serial/kl5kusb105.c index 5bed59cd5776..def9ad258715 100644 --- a/drivers/usb/serial/kl5kusb105.c +++ b/drivers/usb/serial/kl5kusb105.c @@ -311,12 +311,12 @@ static int klsi_105_open(struct tty_struct *tty, struct usb_serial_port *port) /* set up termios structure */ spin_lock_irqsave(&priv->lock, flags); - priv->termios.c_iflag = tty->termios->c_iflag; - priv->termios.c_oflag = tty->termios->c_oflag; - priv->termios.c_cflag = tty->termios->c_cflag; - priv->termios.c_lflag = tty->termios->c_lflag; + priv->termios.c_iflag = tty->termios.c_iflag; + priv->termios.c_oflag = tty->termios.c_oflag; + priv->termios.c_cflag = tty->termios.c_cflag; + priv->termios.c_lflag = tty->termios.c_lflag; for (i = 0; i < NCCS; i++) - priv->termios.c_cc[i] = tty->termios->c_cc[i]; + priv->termios.c_cc[i] = tty->termios.c_cc[i]; priv->cfg.pktlen = cfg->pktlen; priv->cfg.baudrate = cfg->baudrate; priv->cfg.databits = cfg->databits; @@ -445,9 +445,9 @@ static void klsi_105_set_termios(struct tty_struct *tty, struct ktermios *old_termios) { struct klsi_105_private *priv = usb_get_serial_port_data(port); - unsigned int iflag = tty->termios->c_iflag; + unsigned int iflag = tty->termios.c_iflag; unsigned int old_iflag = old_termios->c_iflag; - unsigned int cflag = tty->termios->c_cflag; + unsigned int cflag = tty->termios.c_cflag; unsigned int old_cflag = old_termios->c_cflag; struct klsi_105_port_settings *cfg; unsigned long flags; @@ -560,7 +560,7 @@ static void klsi_105_set_termios(struct tty_struct *tty, if ((cflag & (PARENB|PARODD)) != (old_cflag & (PARENB|PARODD)) || (cflag & CSTOPB) != (old_cflag & CSTOPB)) { /* Not currently supported */ - tty->termios->c_cflag &= ~(PARENB|PARODD|CSTOPB); + tty->termios.c_cflag &= ~(PARENB|PARODD|CSTOPB); #if 0 priv->last_lcr = 0; @@ -587,7 +587,7 @@ static void klsi_105_set_termios(struct tty_struct *tty, || (iflag & IXON) != (old_iflag & IXON) || (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) { /* Not currently supported */ - tty->termios->c_cflag &= ~CRTSCTS; + tty->termios.c_cflag &= ~CRTSCTS; /* Drop DTR/RTS if no flow control otherwise assert */ #if 0 if ((iflag & IXOFF) || (iflag & IXON) || (cflag & CRTSCTS)) diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c index fafeabb64c55..bf5c74965d34 100644 --- a/drivers/usb/serial/kobil_sct.c +++ b/drivers/usb/serial/kobil_sct.c @@ -191,11 +191,11 @@ static void kobil_release(struct usb_serial *serial) static void kobil_init_termios(struct tty_struct *tty) { /* Default to echo off and other sane device settings */ - tty->termios->c_lflag = 0; - tty->termios->c_lflag &= ~(ISIG | ICANON | ECHO | IEXTEN | XCASE); - tty->termios->c_iflag = IGNBRK | IGNPAR | IXOFF; + tty->termios.c_lflag = 0; + tty->termios.c_iflag &= ~(ISIG | ICANON | ECHO | IEXTEN | XCASE); + tty->termios.c_iflag |= IGNBRK | IGNPAR | IXOFF; /* do NOT translate CR to CR-NL (0x0A -> 0x0A 0x0D) */ - tty->termios->c_oflag &= ~ONLCR; + tty->termios.c_oflag &= ~ONLCR; } static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port) @@ -581,14 +581,14 @@ static void kobil_set_termios(struct tty_struct *tty, struct kobil_private *priv; int result; unsigned short urb_val = 0; - int c_cflag = tty->termios->c_cflag; + int c_cflag = tty->termios.c_cflag; speed_t speed; priv = usb_get_serial_port_data(port); if (priv->device_type == KOBIL_USBTWIN_PRODUCT_ID || priv->device_type == KOBIL_KAAN_SIM_PRODUCT_ID) { /* This device doesn't support ioctl calls */ - *tty->termios = *old; + tty_termios_copy_hw(&tty->termios, old); return; } @@ -612,7 +612,7 @@ static void kobil_set_termios(struct tty_struct *tty, urb_val |= SUSBCR_SPASB_EvenParity; } else urb_val |= SUSBCR_SPASB_NoParity; - tty->termios->c_cflag &= ~CMSPAR; + tty->termios.c_cflag &= ~CMSPAR; tty_encode_baud_rate(tty, speed, speed); result = usb_control_msg(port->serial->dev, diff --git a/drivers/usb/serial/mct_u232.c b/drivers/usb/serial/mct_u232.c index a71fa0aa0406..df98cffdba65 100644 --- a/drivers/usb/serial/mct_u232.c +++ b/drivers/usb/serial/mct_u232.c @@ -454,7 +454,7 @@ static int mct_u232_open(struct tty_struct *tty, struct usb_serial_port *port) * either. */ spin_lock_irqsave(&priv->lock, flags); - if (tty && (tty->termios->c_cflag & CBAUD)) + if (tty && (tty->termios.c_cflag & CBAUD)) priv->control_state = TIOCM_DTR | TIOCM_RTS; else priv->control_state = 0; @@ -634,7 +634,7 @@ static void mct_u232_set_termios(struct tty_struct *tty, { struct usb_serial *serial = port->serial; struct mct_u232_private *priv = usb_get_serial_port_data(port); - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; unsigned int cflag = termios->c_cflag; unsigned int old_cflag = old_termios->c_cflag; unsigned long flags; diff --git a/drivers/usb/serial/metro-usb.c b/drivers/usb/serial/metro-usb.c index d47eb06fe463..2b0627b5fe2c 100644 --- a/drivers/usb/serial/metro-usb.c +++ b/drivers/usb/serial/metro-usb.c @@ -130,12 +130,6 @@ static void metrousb_read_int_callback(struct urb *urb) /* Set the data read from the usb port into the serial port buffer. */ tty = tty_port_tty_get(&port->port); - if (!tty) { - dev_err(&port->dev, "%s - bad tty pointer - exiting\n", - __func__); - return; - } - if (tty && urb->actual_length) { /* Loop through the data copying each byte to the tty layer. */ tty_insert_flip_string(tty, data, urb->actual_length); diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c index a07dd3c8cfef..012f67b2e4cc 100644 --- a/drivers/usb/serial/mos7720.c +++ b/drivers/usb/serial/mos7720.c @@ -1349,7 +1349,7 @@ static void mos7720_throttle(struct tty_struct *tty) } /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { mos7720_port->shadowMCR &= ~UART_MCR_RTS; write_mos_reg(port->serial, port->number - port->serial->minor, MCR, mos7720_port->shadowMCR); @@ -1383,7 +1383,7 @@ static void mos7720_unthrottle(struct tty_struct *tty) } /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { mos7720_port->shadowMCR |= UART_MCR_RTS; write_mos_reg(port->serial, port->number - port->serial->minor, MCR, mos7720_port->shadowMCR); @@ -1604,8 +1604,8 @@ static void change_port_settings(struct tty_struct *tty, lStop = 0x00; /* 1 stop bit */ lParity = 0x00; /* No parity */ - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; + cflag = tty->termios.c_cflag; + iflag = tty->termios.c_iflag; /* Change the number of bits */ switch (cflag & CSIZE) { @@ -1753,11 +1753,11 @@ static void mos7720_set_termios(struct tty_struct *tty, dbg("%s\n", "setting termios - ASPIRE"); - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; dbg("%s - cflag %08x iflag %08x", __func__, - tty->termios->c_cflag, - RELEVANT_IFLAG(tty->termios->c_iflag)); + tty->termios.c_cflag, + RELEVANT_IFLAG(tty->termios.c_iflag)); dbg("%s - old cflag %08x old iflag %08x", __func__, old_termios->c_cflag, diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index 2f6da1e89bfa..402c32d7accb 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -1651,7 +1651,7 @@ static void mos7840_throttle(struct tty_struct *tty) return; } /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { mos7840_port->shadowMCR &= ~MCR_RTS; status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, mos7840_port->shadowMCR); @@ -1694,7 +1694,7 @@ static void mos7840_unthrottle(struct tty_struct *tty) } /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { + if (tty->termios.c_cflag & CRTSCTS) { mos7840_port->shadowMCR |= MCR_RTS; status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, mos7840_port->shadowMCR); @@ -2000,8 +2000,8 @@ static void mos7840_change_port_settings(struct tty_struct *tty, lStop = LCR_STOP_1; lParity = LCR_PAR_NONE; - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; + cflag = tty->termios.c_cflag; + iflag = tty->termios.c_iflag; /* Change the number of bits */ if (cflag & CSIZE) { @@ -2161,10 +2161,10 @@ static void mos7840_set_termios(struct tty_struct *tty, dbg("%s", "setting termios - "); - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; dbg("%s - clfag %08x iflag %08x", __func__, - tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag)); + tty->termios.c_cflag, RELEVANT_IFLAG(tty->termios.c_iflag)); dbg("%s - old clfag %08x old iflag %08x", __func__, old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag)); dbg("%s - port %d", __func__, port->number); diff --git a/drivers/usb/serial/oti6858.c b/drivers/usb/serial/oti6858.c index 5976b65ab6ee..9f555560bfbf 100644 --- a/drivers/usb/serial/oti6858.c +++ b/drivers/usb/serial/oti6858.c @@ -404,10 +404,10 @@ static int oti6858_chars_in_buffer(struct tty_struct *tty) static void oti6858_init_termios(struct tty_struct *tty) { - *(tty->termios) = tty_std_termios; - tty->termios->c_cflag = B38400 | CS8 | CREAD | HUPCL | CLOCAL; - tty->termios->c_ispeed = 38400; - tty->termios->c_ospeed = 38400; + tty->termios = tty_std_termios; + tty->termios.c_cflag = B38400 | CS8 | CREAD | HUPCL | CLOCAL; + tty->termios.c_ispeed = 38400; + tty->termios.c_ospeed = 38400; } static void oti6858_set_termios(struct tty_struct *tty, @@ -425,7 +425,7 @@ static void oti6858_set_termios(struct tty_struct *tty, return; } - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; spin_lock_irqsave(&priv->lock, flags); divisor = priv->pending_setup.divisor; diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 13b8dd6481f5..2b9108a8ea64 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -260,16 +260,16 @@ static void pl2303_set_termios(struct tty_struct *tty, serial settings even to the same values as before. Thus we actually need to filter in this specific case */ - if (!tty_termios_hw_change(tty->termios, old_termios)) + if (!tty_termios_hw_change(&tty->termios, old_termios)) return; - cflag = tty->termios->c_cflag; + cflag = tty->termios.c_cflag; buf = kzalloc(7, GFP_KERNEL); if (!buf) { dev_err(&port->dev, "%s - out of memory.\n", __func__); /* Report back no change occurred */ - *tty->termios = *old_termios; + tty->termios = *old_termios; return; } diff --git a/drivers/usb/serial/quatech2.c b/drivers/usb/serial/quatech2.c index 151670b6b72a..7df9cdb053ed 100644 --- a/drivers/usb/serial/quatech2.c +++ b/drivers/usb/serial/quatech2.c @@ -275,7 +275,7 @@ static void qt2_set_termios(struct tty_struct *tty, { struct usb_device *dev = port->serial->dev; struct qt2_port_private *port_priv; - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; u16 baud; unsigned int cflag = termios->c_cflag; u16 new_lcr = 0; @@ -406,7 +406,7 @@ static int qt2_open(struct tty_struct *tty, struct usb_serial_port *port) port_priv->device_port = (u8) device_port; if (tty) - qt2_set_termios(tty, port, tty->termios); + qt2_set_termios(tty, port, &tty->termios); return 0; diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c index 0274710cced5..b14ebbd73567 100644 --- a/drivers/usb/serial/sierra.c +++ b/drivers/usb/serial/sierra.c @@ -382,7 +382,7 @@ static int sierra_send_setup(struct usb_serial_port *port) static void sierra_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { - tty_termios_copy_hw(tty->termios, old_termios); + tty_termios_copy_hw(&tty->termios, old_termios); sierra_send_setup(port); } diff --git a/drivers/usb/serial/spcp8x5.c b/drivers/usb/serial/spcp8x5.c index cad608984710..ab68a4d74d61 100644 --- a/drivers/usb/serial/spcp8x5.c +++ b/drivers/usb/serial/spcp8x5.c @@ -316,10 +316,10 @@ static void spcp8x5_dtr_rts(struct usb_serial_port *port, int on) static void spcp8x5_init_termios(struct tty_struct *tty) { /* for the 1st time call this function */ - *(tty->termios) = tty_std_termios; - tty->termios->c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL; - tty->termios->c_ispeed = 115200; - tty->termios->c_ospeed = 115200; + tty->termios = tty_std_termios; + tty->termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL; + tty->termios.c_ispeed = 115200; + tty->termios.c_ospeed = 115200; } /* set the serial param for transfer. we should check if we really need to @@ -330,7 +330,7 @@ static void spcp8x5_set_termios(struct tty_struct *tty, struct usb_serial *serial = port->serial; struct spcp8x5_private *priv = usb_get_serial_port_data(port); unsigned long flags; - unsigned int cflag = tty->termios->c_cflag; + unsigned int cflag = tty->termios.c_cflag; unsigned int old_cflag = old_termios->c_cflag; unsigned short uartdata; unsigned char buf[2] = {0, 0}; @@ -340,7 +340,7 @@ static void spcp8x5_set_termios(struct tty_struct *tty, /* check that they really want us to change something */ - if (!tty_termios_hw_change(tty->termios, old_termios)) + if (!tty_termios_hw_change(&tty->termios, old_termios)) return; /* set DTR/RTS active */ diff --git a/drivers/usb/serial/ssu100.c b/drivers/usb/serial/ssu100.c index 3fee23bf0c14..cf2d30cf7588 100644 --- a/drivers/usb/serial/ssu100.c +++ b/drivers/usb/serial/ssu100.c @@ -216,7 +216,7 @@ static void ssu100_set_termios(struct tty_struct *tty, struct ktermios *old_termios) { struct usb_device *dev = port->serial->dev; - struct ktermios *termios = tty->termios; + struct ktermios *termios = &tty->termios; u16 baud, divisor, remainder; unsigned int cflag = termios->c_cflag; u16 urb_value = 0; /* will hold the new flags */ @@ -322,7 +322,7 @@ static int ssu100_open(struct tty_struct *tty, struct usb_serial_port *port) dbg("%s - set uart failed", __func__); if (tty) - ssu100_set_termios(tty, port, tty->termios); + ssu100_set_termios(tty, port, &tty->termios); return usb_serial_generic_open(tty, port); } diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c index a4404f5ad68e..f502a16aac21 100644 --- a/drivers/usb/serial/ti_usb_3410_5052.c +++ b/drivers/usb/serial/ti_usb_3410_5052.c @@ -520,7 +520,7 @@ static int ti_open(struct tty_struct *tty, struct usb_serial_port *port) } if (tty) - ti_set_termios(tty, port, tty->termios); + ti_set_termios(tty, port, &tty->termios); dbg("%s - sending TI_OPEN_PORT", __func__); status = ti_command_out_sync(tdev, TI_OPEN_PORT, @@ -562,7 +562,7 @@ static int ti_open(struct tty_struct *tty, struct usb_serial_port *port) usb_clear_halt(dev, port->read_urb->pipe); if (tty) - ti_set_termios(tty, port, tty->termios); + ti_set_termios(tty, port, &tty->termios); dbg("%s - sending TI_OPEN_PORT (2)", __func__); status = ti_command_out_sync(tdev, TI_OPEN_PORT, @@ -831,8 +831,8 @@ static void ti_set_termios(struct tty_struct *tty, int port_number = port->number - port->serial->minor; unsigned int mcr; - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; + cflag = tty->termios.c_cflag; + iflag = tty->termios.c_iflag; dbg("%s - cflag %08x, iflag %08x", __func__, cflag, iflag); dbg("%s - old clfag %08x, old iflag %08x", __func__, @@ -871,7 +871,7 @@ static void ti_set_termios(struct tty_struct *tty, } /* CMSPAR isn't supported by this driver */ - tty->termios->c_cflag &= ~CMSPAR; + tty->termios.c_cflag &= ~CMSPAR; if (cflag & PARENB) { if (cflag & PARODD) { diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 27483f91a4a3..aa4b0d775992 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -207,7 +207,7 @@ static int serial_install(struct tty_driver *driver, struct tty_struct *tty) if (retval) goto error_get_interface; - retval = tty_standard_install(driver, tty); + retval = tty_port_install(&port->port, driver, tty); if (retval) goto error_init_termios; @@ -305,8 +305,7 @@ static void serial_close(struct tty_struct *tty, struct file *filp) * Do the resource freeing and refcount dropping for the port. * Avoid freeing the console. * - * Called asynchronously after the last tty kref is dropped, - * and the tty layer has already done the tty_shutdown(tty); + * Called asynchronously after the last tty kref is dropped. */ static void serial_cleanup(struct tty_struct *tty) { @@ -423,7 +422,7 @@ static void serial_set_termios(struct tty_struct *tty, struct ktermios *old) if (port->serial->type->set_termios) port->serial->type->set_termios(tty, port, old); else - tty_termios_copy_hw(tty->termios, old); + tty_termios_copy_hw(&tty->termios, old); } static int serial_break(struct tty_struct *tty, int break_state) diff --git a/drivers/usb/serial/usb_wwan.c b/drivers/usb/serial/usb_wwan.c index 6855d5ed0331..72b678d90831 100644 --- a/drivers/usb/serial/usb_wwan.c +++ b/drivers/usb/serial/usb_wwan.c @@ -67,7 +67,7 @@ void usb_wwan_set_termios(struct tty_struct *tty, struct usb_wwan_intf_private *intfdata = port->serial->private; /* Doesn't support option setting */ - tty_termios_copy_hw(tty->termios, old_termios); + tty_termios_copy_hw(&tty->termios, old_termios); if (intfdata->send_setup) intfdata->send_setup(port); diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c index 473635e7f5db..b36077de72b9 100644 --- a/drivers/usb/serial/whiteheat.c +++ b/drivers/usb/serial/whiteheat.c @@ -724,7 +724,7 @@ static void firm_setup_port(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct whiteheat_port_settings port_settings; - unsigned int cflag = tty->termios->c_cflag; + unsigned int cflag = tty->termios.c_cflag; port_settings.port = port->number + 1; |